As an accurate 2D/3D fabrication tool,inkjet printing technology has great potential in preparation of micro electronic devices.The morphology of droplets produced by the inkjet printer has a great impact on the accur...As an accurate 2D/3D fabrication tool,inkjet printing technology has great potential in preparation of micro electronic devices.The morphology of droplets produced by the inkjet printer has a great impact on the accuracy of deposition.In this study,the drop-on-demand(DoD)inkjet simulation model was established,and the accuracy of the simulation model was verified by corresponding experiments.The simulation result shows that the velocity of the droplet front and tail,as well as the time to disconnect from the nozzle is mainly affected by density(ρ),viscosity(μ)and surface tension(σ)of droplets.When the liquid filament is about to disconnect from the nozzle,the filament length and filament front velocity are found to have a linear correlation withσ/ρμand ln(ρ/(μσ1/2)).展开更多
Polypropylene is commonly used as a binder for ceramic injection molding,and rapid cooling is often encountered during processing.However,the crystallization behavior of polypropylene shows a strong dependence on cool...Polypropylene is commonly used as a binder for ceramic injection molding,and rapid cooling is often encountered during processing.However,the crystallization behavior of polypropylene shows a strong dependence on cooling rate due to its semi-crystalline characteristics.Therefore,the influence of cooling rate on the quality of final product cannot be ignored.In this study,the fast differential scanning calorimetry(FSC)test was performed to study the influence of cooling rate on the non-isothermal crystallization behavior and non-isothermal crystallization kinetics of a copolymer polypropylene(PP BC03B).The results show that the crystallization temperatures and crystallinity decrease as the cooling rate increases.In addition,two exothermic peaks occur when cooling rate ranges from 30 to 300 K·s^(-1),indicating the formation of another crystal phase.Avrami,Ozawa and Mo equations were used to explore the non-isothermal crystallization kinetics,and it can be concluded that the Mo method is suitable for this study.展开更多
Study on turbine blades is crucial due to their critical role in ensuring the efficient and reliable operation of aircraft engines.Nickel-based single crystal superalloys are extensively used in the hot manufacturing ...Study on turbine blades is crucial due to their critical role in ensuring the efficient and reliable operation of aircraft engines.Nickel-based single crystal superalloys are extensively used in the hot manufacturing of turbine blades due to their exceptional high-temperature mechanical properties.The hot manufacturing of single crystal blades involves directional solidification and heat treatment.Experimental manufacturing of these blades is time-consuming,capital-intensive,and often insufficient to meet industrial demands.Numerical simulation techniques have gained widespread acceptance in blade manufacturing research due to their low energy consumption,high efficiency,and rapid turnaround time.This article introduces the modeling and simulation of hot manufacturing in single crystal blades.The discussion outlines the prevalent mathematical models employed in numerical simulations related to blade hot manufacturing.It encapsulates the advancements in research concerning macro to micro-level numerical simulation techniques for directional solidification and heat treatment processes.Furthermore,potential future trajectories for the numerical simulation of single crystal blade hot manufacturing are also discussed.展开更多
To enhance the accuracy of mechanical simulation in the directional solidification process of turbine blades for heavy-duty gas turbines,a new constitutive model that employs machine learning methods was developed.Thi...To enhance the accuracy of mechanical simulation in the directional solidification process of turbine blades for heavy-duty gas turbines,a new constitutive model that employs machine learning methods was developed.This model incorporates incremental learning and transfer learning,thus improves the predictive accuracy and generalization performance.To account for the anisotropy of the directionally solidified alloy,a deformation direction parameter is added to the model,enabling prediction of the stress-strain relationship of the alloy under different deformation directions.The predictive capabilities of both models are evaluated using correlation coefficient(R),average relative error(δ),and value of relative error(RE).Compared to the traditional model,the machine learning constitutive model achieves higher prediction accuracy and better generalization performance.This offers a new approach for the establishment of flow constitutive models for other directionally solidified and single-crystal superalloys.展开更多
Selective laser melting （SLM） is a powerful additive manufacturing （AM） technology, of which the most prominent advantage is the ability to produce components with a complex geometry. The service performances of t...Selective laser melting （SLM） is a powerful additive manufacturing （AM） technology, of which the most prominent advantage is the ability to produce components with a complex geometry. The service performances of the SLM-processed components depend on the microstructure and surface quality. In this work, the microstructures, mechanical properties, and fracture behaviors of SLM-processed Ti-6AI-4V alloy under machined and as-built surfaces after annealing treatments and hot isostatic pressing （HIP） were investigated. The microstructures were analyzed by optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscopy （TEM）. The mechanical properties were measured by tensile testing at room temperature. The results indicate that the as-deposited microstructures are characterized by columnar grains and fine brittle martensite and the as- deposited properties present high strength, low ductility and obvious anisotropy. After annealing at 800-900~C for 2-4 h and HIP at 920~C/100MPa for 2 h, the brittle martensite could be transformed into ductile lamellar （a＋~） microstructure and the static tensile properties of SLM-processed Ti-6AI-4V alloys in the machined condition could be comparable to that of wrought materials. Even after HIP treatment, the as-built surfaces could decrease the ductility and reduction of area of SLM-processed fi-6AI-4V alloys to 9.2% and 20%, respectively. The crack initiation could occur at the columnar grain boundaries or at the as-built surfaces. The lamellar （a＋13） microstructures and columnar grains could hinder or distort the crack propagation path during tensile tests.展开更多
An understanding of dendrite growth is required in order to improve the properties of castings. For this reason, cellular automaton-finite difference(CA-FD) method was used to investigate the dendrite growth during di...An understanding of dendrite growth is required in order to improve the properties of castings. For this reason, cellular automaton-finite difference(CA-FD) method was used to investigate the dendrite growth during directional solidification(DS)process. The solute diffusion model combined with macro temperature field model was established for predicting the dendrite growth behavior. Model validation was performed by the DS experiment, and the cooling curves and grain structures obtained by the experiment presented a reasonable agreement with the simulation results. The competitive growth of dendrites was also simulated by the proposed model, and the competitive behavior of dendrites with different misalignment angles was also discussed in detail.Subsequently, 3D dendrites growth was also investigated by experiment and simulation, and both were in good accordance. The influence on dendrites growth of initial nucleus was investigated by three simulation cases, and the results showed that the initial nuclei just had an effect on the initial growth stage of columnar dendrites, but had little influence on the final dendritic morphology and the primary dendrite arm spacing.展开更多
Turbine blades,produced by the directional solidification(DS)process,often require high dimensional accuracy and excellent mechanical properties.A critical step in their production is the fabrication of wax patterns.H...Turbine blades,produced by the directional solidification(DS)process,often require high dimensional accuracy and excellent mechanical properties.A critical step in their production is the fabrication of wax patterns.However,the traditional manufacturing process has many disadvantages,such as long-term production,low material utilization rate,and the high cost of producing a complex-shaped wax pattern.Selective laser sintering(SLS)is one of the most extensively used additive manufacturing techniques that substantially shortens the production cycle.In this study,SLS was adopted to fabricate the wax pattern instead of the traditional manufacturing process.The orthogonal experiment method was carried out to investigate the effects of laser power,scanning speed,scanning space,and layer thickness on the dimensional precision and morphologies of the SLS parts.The SLS parts showed a minimum dimensional deviation when laser power,scanning speed,scanning space,and layer thickness were 10 W,3000 mm·s^(-1),0.18 mm,and 0.25 mm,respectively.In addition,the tensile strength and fracture morphologies were closely associated with the laser volumetric energy density(VED).The tensile strength reached a maximum when the VED was 0.0762 J·mm-3,with an evident brittle fracture morphology.The wax pattern manufactured in this way meets the accuracy and strength requirements for investment casting.This research offers a novel path for the production of wax patterns for complex-shaped turbine blades by SLS.展开更多
Numerical heat-transfer and turbulent flow model for an industrial high-pressure gas quenching vacuum furnace was established to simulate the heating,holding and gas fan quenching of a low rhenium-bearing Ni-based sin...Numerical heat-transfer and turbulent flow model for an industrial high-pressure gas quenching vacuum furnace was established to simulate the heating,holding and gas fan quenching of a low rhenium-bearing Ni-based single crystal turbine blade.The mesh of simplified furnace model was built using finite volume method and the boundary conditions were set up according to the practical process.Simulation results show that the turbine blade geometry and the mutual shielding among blades have significant influence on the uniformity of the temperature distribution.The temperature distribution at sharp corner,thin wall and corner part is higher than that at thick wall part of blade during heating,and the isotherms show a toroidal line to the center of thick wall.The temperature of sheltered units is lower than that of the remaining part of blade.When there is no shelteration among multiple blades,the temperature distribution for all blades is almost identical.The fluid velocity field,temperature field and cooling curves of the single and multiple turbine blades during gas fan quenching were also simulated.Modeling results indicate that the loading tray,free outlet and the location of turbine blades have important influences on the flow field.The high-speed gas flows out from the nozzle is divided by loading tray,and the free outlet enhanced the two vortex flow at the end of the furnace door.The closer the blade is to the exhaust outlet and the nozzle,the greater the flow velocity is and the more adequate the flow is.The blade geometry has an effect on the cooling for single blade and multiple blades during gas fan quenching,and the effects in double layers differs from that in single layer.For single blade,the cooing rate at thin-walled part is lower than that at thick-walled part,the cooling rate at sharp corner is greater than that at tenon and blade platform,and the temperature at regions close to the internal position is decreased more slowly than that close to the surface.For multiple blades in single layer,the temperature at sharp corner or thin wall in the blade that close to the nozzles is much lower,and the temperature distribution of blades is almost parallel.The cooling rate inside the air current channel is lower than that of at the position near blade platform and tenon,and the effect of blade location to the nozzles on the temperature field inside the blade is lower than that on the blade surface.For multiple blades in double layers,the flow velocity is low,and the flow is not uniform for blades in the second-layer due to the shielding of blades in the first-layer.the cooling rate of blades in the second-layer is lower than that in the first-layer.The cooling rate of blade close to the nozzles in the first-layer is the higher than that of blade away from the nozzles in the second-layer,and the temperature distribution on blades in the same layer is almost parallel.The cooling rate in thin wall position of blade away from the nozzles is larger than that in tenon of the blade closer to the nozzles in the same layer.The cooling rate for blades in the secondlayer is much lower both in thin wall and tenon for blades away from the nozzles.展开更多
Due to the extensive application of Al-Si alloys in the automotive and aerospace industries as structural components, an understanding of their microstructural formation, such as dendrite and(Al+Si) eutectic, is of gr...Due to the extensive application of Al-Si alloys in the automotive and aerospace industries as structural components, an understanding of their microstructural formation, such as dendrite and(Al+Si) eutectic, is of great importance to control the desirable microstructure, so as to modify the performance of castings. Since previous major themes of microstructural simulation are dendrite and regular eutectic growth, few efforts have been paid to simulate the irregular eutectic growth. Therefore, a multiphase cellular automaton(CA) model is developed and applied to simulate the time-dependent Al-Si irregular eutectic growth. Prior to model establishment, related experiments were carried out to investigate the influence of cooling rate and Sr modification on the growth of eutectic Si. This CA model incorporates several aspects, including growth algorithms and nucleation criterion, to achieve the competitive and cooperative growth mechanism for nonfaceted-faceted Al-Si irregular eutectic. The growth kinetics considers thermal undercooling, constitutional undercooling, and curvature undercooling, as well as the anisotropic characteristic of eutectic Si growth. The capturing rule takes into account the effects of modification on the silicon growth behaviors.The simulated results indicate that for unmodified alloy, the higher eutectic undercooling results in the higher eutectic growth velocity, and a more refined eutectic microstructure as well as narrower eutectic lamellar spacing. For modified alloy, the eutectic silicon tends to be obvious fibrous morphology and the morphology of eutectic Si is determined by both chemical modifier and cooling rate. The predicted microstructure of Al-7Si alloy under different solidification conditions shows that this proposed model can successfully reproduce both dendrite and eutectic microstructures.展开更多
Additive manufacturing,is originally known as rapid prototyping manufacturing,and nowadays more commonly known as 3D printing.It is a manufacturing method based on the principle of"discrete/stacking",which t...Additive manufacturing,is originally known as rapid prototyping manufacturing,and nowadays more commonly known as 3D printing.It is a manufacturing method based on the principle of"discrete/stacking",which transfers the traditional multidimensional"subtractive"manufacturing into the two-dimensional manufacturing by layer-by-layer additive stacking.展开更多
An effort to obtain superior impact properties for Al-7Si-0.35 Mg alloy is presented,where modification with 0.02 wt% Sr and 0.1 wt% La as well as solution treatment was jointly employed.The samples were solution trea...An effort to obtain superior impact properties for Al-7Si-0.35 Mg alloy is presented,where modification with 0.02 wt% Sr and 0.1 wt% La as well as solution treatment was jointly employed.The samples were solution treated at 535℃ for 15 min to 12 h.The microstructure,fracture mechanism,and their correlation with the impact properties of the alloy were studied in detail mainly through optical microscopy(OM),scanning electron microscopy(SEM) and oscillography impact test.The results show that the addition of Sr and La refined the eutectic Si particles significantly from~ 2.05 μm(modified with Sr alone) to~ 0.75 μm in as-cast microstructure,leading to a very homogeneous distribution of spheroidized Si particles in the alloy solution treated at 535℃ for 8 h.The alloy exhibits excellent impact toughness up to 75 J·cm^(-2),which is much higher than the maximum impact toughness of the alloys modified by Sr alone(~ 46 J·cm^(-2)).The major reason for this remarkable increase in the impact property is the dramatic increase in crack initiation energy.The dispersoid-free zones(DFZs)near the eutectic regions mainly consist of the ductile Al-matrix,which exhibits excellent ductility.The ductile Al-matrix of the DFZs hinders the crack propagation,resulting in a significant increase in crack propagation energy.展开更多
Since most typical alloys in industrial applications are multicomponent with three or more components, and various CA models proposed in the past mainly focus on the binary alloys, a two-dimensional modified cellular ...Since most typical alloys in industrial applications are multicomponent with three or more components, and various CA models proposed in the past mainly focus on the binary alloys, a two-dimensional modified cellular automaton model allowing for the quantitatively predicting dendrite growth of multicomponent alloys in the low P6clet number regime is presented. The elimination of the mesh-induced anisotropy is achieved by adopting a modified virtual front tracking method. A new efficient method based on the lever rule is applied to calculate the solid fraction increment of the interfacial cells. The thermodynamic data such as liquidus temperature, the partition coefficients, and the slope of liquidus surface, needed for determining the dynamics of dendrite growth, are obtained by coupling with PanEngine. This model is applied to simulate the dendrite morphology and microsegregation of A1-Cu-Mg temary alloy both for single and multi- dendrites growth. The simulated results demonstrate that the difference of the concentration distribution profiles ahead of the dendrite tip for each alloying element mainly results from the different partition coefficients and solute diffusion coefficients. Comparison with the prediction of analytical model is carded out and it reveals the correctness of the model. Consequently, the difference in interdendritic microsegregation behavior of different components is analyzed.展开更多
In the present investigation, a coupled crystal plasticity finite-element(CPFE) and cellular automaton(CA) model was developed to predict the microstructure of recrystallization in single-crystal(SX) Ni-based superall...In the present investigation, a coupled crystal plasticity finite-element(CPFE) and cellular automaton(CA) model was developed to predict the microstructure of recrystallization in single-crystal(SX) Ni-based superalloy.The quasi-static compressive tests of [001] orientated SX DD6 superalloy were conducted on Gleeble3500 tester to calibrate the CPFE model based on crystal slip kinematics.The simulated stress-strain curve agrees well with the experimental results. Quantitative deformation amount was introduced in the deformed samples of simulation and experiment, and these samples were subsequently subjected to the standard solution heat treatment(SSHT).Results of CA simulation show that the recrystallization(RX) nucleation tends to occur at the third stage of SSHT process due to the high critical temperature of RX nucleation for the samples deformed at room temperature. The inhomogeneous RX grains gradually coarsen and compete to reach more stable status by reducing the system energy.Simulated RX grain density decreases from 7.500 to1.875 mm,agreeing well with the value of 1.920 mmfrom electron backscattered diffraction(EBSD) detection of the experimental sample.展开更多
The thermosolutal convection can alter segregation pattern,change dendrite morphology and even cause freckles formation in alloy solidification.In this work,the multiphase-field model was coupled with lattice Boltzman...The thermosolutal convection can alter segregation pattern,change dendrite morphology and even cause freckles formation in alloy solidification.In this work,the multiphase-field model was coupled with lattice Boltzmann method to simulate the dendrite growth under melt convection in superalloy solidification.In the isothermal solidification simulations,zero and normal gravitational accelerations were applied to investigate the effects of gravity on the dendrite morphology and the magnitude of melt flow.The solute distribution of each alloy component along with the dendrite tip velocity during solidification was obtained,and the natural convection has been confirmed to affect the microsegregation pattern and the dendrite growth velocity.In the directional solidification simulations,two typical temperature gradients were applied,and the dendrite morphology and fluid velocity in the mushy zone during solidification were analyzed.It is found that the freckles will form when the average fluid velocity in the mushy zone exceeds the withdraw velocity.展开更多
基金supported by the Tsinghua University–Toyota Research Center Project。
文摘As an accurate 2D/3D fabrication tool,inkjet printing technology has great potential in preparation of micro electronic devices.The morphology of droplets produced by the inkjet printer has a great impact on the accuracy of deposition.In this study,the drop-on-demand(DoD)inkjet simulation model was established,and the accuracy of the simulation model was verified by corresponding experiments.The simulation result shows that the velocity of the droplet front and tail,as well as the time to disconnect from the nozzle is mainly affected by density(ρ),viscosity(μ)and surface tension(σ)of droplets.When the liquid filament is about to disconnect from the nozzle,the filament length and filament front velocity are found to have a linear correlation withσ/ρμand ln(ρ/(μσ1/2)).
基金financially supported by a grant provided by Mitsubishi Heavy Industries。
文摘Polypropylene is commonly used as a binder for ceramic injection molding,and rapid cooling is often encountered during processing.However,the crystallization behavior of polypropylene shows a strong dependence on cooling rate due to its semi-crystalline characteristics.Therefore,the influence of cooling rate on the quality of final product cannot be ignored.In this study,the fast differential scanning calorimetry(FSC)test was performed to study the influence of cooling rate on the non-isothermal crystallization behavior and non-isothermal crystallization kinetics of a copolymer polypropylene(PP BC03B).The results show that the crystallization temperatures and crystallinity decrease as the cooling rate increases.In addition,two exothermic peaks occur when cooling rate ranges from 30 to 300 K·s^(-1),indicating the formation of another crystal phase.Avrami,Ozawa and Mo equations were used to explore the non-isothermal crystallization kinetics,and it can be concluded that the Mo method is suitable for this study.
基金supported by the Stable Support Project and the Major National Science and Technology Project(Grant No.2017-VII-0008-0101).
文摘Study on turbine blades is crucial due to their critical role in ensuring the efficient and reliable operation of aircraft engines.Nickel-based single crystal superalloys are extensively used in the hot manufacturing of turbine blades due to their exceptional high-temperature mechanical properties.The hot manufacturing of single crystal blades involves directional solidification and heat treatment.Experimental manufacturing of these blades is time-consuming,capital-intensive,and often insufficient to meet industrial demands.Numerical simulation techniques have gained widespread acceptance in blade manufacturing research due to their low energy consumption,high efficiency,and rapid turnaround time.This article introduces the modeling and simulation of hot manufacturing in single crystal blades.The discussion outlines the prevalent mathematical models employed in numerical simulations related to blade hot manufacturing.It encapsulates the advancements in research concerning macro to micro-level numerical simulation techniques for directional solidification and heat treatment processes.Furthermore,potential future trajectories for the numerical simulation of single crystal blade hot manufacturing are also discussed.
基金supported by the National Science and Technology Major Project(2017-VII-0008-0101).
文摘To enhance the accuracy of mechanical simulation in the directional solidification process of turbine blades for heavy-duty gas turbines,a new constitutive model that employs machine learning methods was developed.This model incorporates incremental learning and transfer learning,thus improves the predictive accuracy and generalization performance.To account for the anisotropy of the directionally solidified alloy,a deformation direction parameter is added to the model,enabling prediction of the stress-strain relationship of the alloy under different deformation directions.The predictive capabilities of both models are evaluated using correlation coefficient(R),average relative error(δ),and value of relative error(RE).Compared to the traditional model,the machine learning constitutive model achieves higher prediction accuracy and better generalization performance.This offers a new approach for the establishment of flow constitutive models for other directionally solidified and single-crystal superalloys.
基金financially supported by the National Program on Key Basic Research Project of China(973 Program)under Grant(No.613281)the National Natural Science Foundation of China(No.51505451)+3 种基金the Natural Science Foundation of Beijing(No.3172042)supported by EMUSIC which is part of an EU-China collaborationthe European Union’s Horizon 2020 research and innovation programme under Grant Agreement No.690725MIIT under the programme number MJ-2015-H-G-104
文摘Selective laser melting （SLM） is a powerful additive manufacturing （AM） technology, of which the most prominent advantage is the ability to produce components with a complex geometry. The service performances of the SLM-processed components depend on the microstructure and surface quality. In this work, the microstructures, mechanical properties, and fracture behaviors of SLM-processed Ti-6AI-4V alloy under machined and as-built surfaces after annealing treatments and hot isostatic pressing （HIP） were investigated. The microstructures were analyzed by optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscopy （TEM）. The mechanical properties were measured by tensile testing at room temperature. The results indicate that the as-deposited microstructures are characterized by columnar grains and fine brittle martensite and the as- deposited properties present high strength, low ductility and obvious anisotropy. After annealing at 800-900~C for 2-4 h and HIP at 920~C/100MPa for 2 h, the brittle martensite could be transformed into ductile lamellar （a＋~） microstructure and the static tensile properties of SLM-processed Ti-6AI-4V alloys in the machined condition could be comparable to that of wrought materials. Even after HIP treatment, the as-built surfaces could decrease the ductility and reduction of area of SLM-processed fi-6AI-4V alloys to 9.2% and 20%, respectively. The crack initiation could occur at the columnar grain boundaries or at the as-built surfaces. The lamellar （a＋13） microstructures and columnar grains could hinder or distort the crack propagation path during tensile tests.
基金Project(2017ZX04014001) supported by the National Science and Technology Major Project of ChinaProject(2017YFB0701503) supported by the National Key R&D Program of ChinaProject(51374137) supported by the National Natural Science Foundation of China
文摘An understanding of dendrite growth is required in order to improve the properties of castings. For this reason, cellular automaton-finite difference(CA-FD) method was used to investigate the dendrite growth during directional solidification(DS)process. The solute diffusion model combined with macro temperature field model was established for predicting the dendrite growth behavior. Model validation was performed by the DS experiment, and the cooling curves and grain structures obtained by the experiment presented a reasonable agreement with the simulation results. The competitive growth of dendrites was also simulated by the proposed model, and the competitive behavior of dendrites with different misalignment angles was also discussed in detail.Subsequently, 3D dendrites growth was also investigated by experiment and simulation, and both were in good accordance. The influence on dendrites growth of initial nucleus was investigated by three simulation cases, and the results showed that the initial nuclei just had an effect on the initial growth stage of columnar dendrites, but had little influence on the final dendritic morphology and the primary dendrite arm spacing.
基金financially supported by National Science and Technology Major Project(2017ZX04014001-002)China-EU(European Union)Science&Technology Cooperation in Aviation+1 种基金Horizon 2020 Framework Programme for Research and Innovation(2014-2020)of EU(No.690725)National Natural Science Foundation of China(No.51374137)
文摘Turbine blades,produced by the directional solidification(DS)process,often require high dimensional accuracy and excellent mechanical properties.A critical step in their production is the fabrication of wax patterns.However,the traditional manufacturing process has many disadvantages,such as long-term production,low material utilization rate,and the high cost of producing a complex-shaped wax pattern.Selective laser sintering(SLS)is one of the most extensively used additive manufacturing techniques that substantially shortens the production cycle.In this study,SLS was adopted to fabricate the wax pattern instead of the traditional manufacturing process.The orthogonal experiment method was carried out to investigate the effects of laser power,scanning speed,scanning space,and layer thickness on the dimensional precision and morphologies of the SLS parts.The SLS parts showed a minimum dimensional deviation when laser power,scanning speed,scanning space,and layer thickness were 10 W,3000 mm·s^(-1),0.18 mm,and 0.25 mm,respectively.In addition,the tensile strength and fracture morphologies were closely associated with the laser volumetric energy density(VED).The tensile strength reached a maximum when the VED was 0.0762 J·mm-3,with an evident brittle fracture morphology.The wax pattern manufactured in this way meets the accuracy and strength requirements for investment casting.This research offers a novel path for the production of wax patterns for complex-shaped turbine blades by SLS.
基金financially supported by the National Natural Science Foundation of China(grant nos.51374137 and 51171089)National Science and Technology Major Special Project of China(grant no.2012ZX04012-011)National Basic Research Program of China(grant no.2011CB706801)
文摘Numerical heat-transfer and turbulent flow model for an industrial high-pressure gas quenching vacuum furnace was established to simulate the heating,holding and gas fan quenching of a low rhenium-bearing Ni-based single crystal turbine blade.The mesh of simplified furnace model was built using finite volume method and the boundary conditions were set up according to the practical process.Simulation results show that the turbine blade geometry and the mutual shielding among blades have significant influence on the uniformity of the temperature distribution.The temperature distribution at sharp corner,thin wall and corner part is higher than that at thick wall part of blade during heating,and the isotherms show a toroidal line to the center of thick wall.The temperature of sheltered units is lower than that of the remaining part of blade.When there is no shelteration among multiple blades,the temperature distribution for all blades is almost identical.The fluid velocity field,temperature field and cooling curves of the single and multiple turbine blades during gas fan quenching were also simulated.Modeling results indicate that the loading tray,free outlet and the location of turbine blades have important influences on the flow field.The high-speed gas flows out from the nozzle is divided by loading tray,and the free outlet enhanced the two vortex flow at the end of the furnace door.The closer the blade is to the exhaust outlet and the nozzle,the greater the flow velocity is and the more adequate the flow is.The blade geometry has an effect on the cooling for single blade and multiple blades during gas fan quenching,and the effects in double layers differs from that in single layer.For single blade,the cooing rate at thin-walled part is lower than that at thick-walled part,the cooling rate at sharp corner is greater than that at tenon and blade platform,and the temperature at regions close to the internal position is decreased more slowly than that close to the surface.For multiple blades in single layer,the temperature at sharp corner or thin wall in the blade that close to the nozzles is much lower,and the temperature distribution of blades is almost parallel.The cooling rate inside the air current channel is lower than that of at the position near blade platform and tenon,and the effect of blade location to the nozzles on the temperature field inside the blade is lower than that on the blade surface.For multiple blades in double layers,the flow velocity is low,and the flow is not uniform for blades in the second-layer due to the shielding of blades in the first-layer.the cooling rate of blades in the second-layer is lower than that in the first-layer.The cooling rate of blade close to the nozzles in the first-layer is the higher than that of blade away from the nozzles in the second-layer,and the temperature distribution on blades in the same layer is almost parallel.The cooling rate in thin wall position of blade away from the nozzles is larger than that in tenon of the blade closer to the nozzles in the same layer.The cooling rate for blades in the secondlayer is much lower both in thin wall and tenon for blades away from the nozzles.
基金financially supported by the National Basic Research Program of China(Grant No.2011CB706801)the National Natural Science Foundation of China(Grant No.51374137,51171089)the National Science and Technology Major Projects(Grant No.2012ZX04012-011,2011ZX04014-052)
文摘Due to the extensive application of Al-Si alloys in the automotive and aerospace industries as structural components, an understanding of their microstructural formation, such as dendrite and(Al+Si) eutectic, is of great importance to control the desirable microstructure, so as to modify the performance of castings. Since previous major themes of microstructural simulation are dendrite and regular eutectic growth, few efforts have been paid to simulate the irregular eutectic growth. Therefore, a multiphase cellular automaton(CA) model is developed and applied to simulate the time-dependent Al-Si irregular eutectic growth. Prior to model establishment, related experiments were carried out to investigate the influence of cooling rate and Sr modification on the growth of eutectic Si. This CA model incorporates several aspects, including growth algorithms and nucleation criterion, to achieve the competitive and cooperative growth mechanism for nonfaceted-faceted Al-Si irregular eutectic. The growth kinetics considers thermal undercooling, constitutional undercooling, and curvature undercooling, as well as the anisotropic characteristic of eutectic Si growth. The capturing rule takes into account the effects of modification on the silicon growth behaviors.The simulated results indicate that for unmodified alloy, the higher eutectic undercooling results in the higher eutectic growth velocity, and a more refined eutectic microstructure as well as narrower eutectic lamellar spacing. For modified alloy, the eutectic silicon tends to be obvious fibrous morphology and the morphology of eutectic Si is determined by both chemical modifier and cooling rate. The predicted microstructure of Al-7Si alloy under different solidification conditions shows that this proposed model can successfully reproduce both dendrite and eutectic microstructures.
文摘Additive manufacturing,is originally known as rapid prototyping manufacturing,and nowadays more commonly known as 3D printing.It is a manufacturing method based on the principle of"discrete/stacking",which transfers the traditional multidimensional"subtractive"manufacturing into the two-dimensional manufacturing by layer-by-layer additive stacking.
基金financially supported by Beijing Natural Science Foundation (No.L223001)。
文摘An effort to obtain superior impact properties for Al-7Si-0.35 Mg alloy is presented,where modification with 0.02 wt% Sr and 0.1 wt% La as well as solution treatment was jointly employed.The samples were solution treated at 535℃ for 15 min to 12 h.The microstructure,fracture mechanism,and their correlation with the impact properties of the alloy were studied in detail mainly through optical microscopy(OM),scanning electron microscopy(SEM) and oscillography impact test.The results show that the addition of Sr and La refined the eutectic Si particles significantly from~ 2.05 μm(modified with Sr alone) to~ 0.75 μm in as-cast microstructure,leading to a very homogeneous distribution of spheroidized Si particles in the alloy solution treated at 535℃ for 8 h.The alloy exhibits excellent impact toughness up to 75 J·cm^(-2),which is much higher than the maximum impact toughness of the alloys modified by Sr alone(~ 46 J·cm^(-2)).The major reason for this remarkable increase in the impact property is the dramatic increase in crack initiation energy.The dispersoid-free zones(DFZs)near the eutectic regions mainly consist of the ductile Al-matrix,which exhibits excellent ductility.The ductile Al-matrix of the DFZs hinders the crack propagation,resulting in a significant increase in crack propagation energy.
基金financially supported by the National Basic Research Program of China (No. 2011CB706801)the National Natural Science Foundation of China (Nos. 51171089 and 51374137)the National Science and Technology Major Project of the Ministry of Science and Technology of China (No. 2012ZX04012-011)
文摘Since most typical alloys in industrial applications are multicomponent with three or more components, and various CA models proposed in the past mainly focus on the binary alloys, a two-dimensional modified cellular automaton model allowing for the quantitatively predicting dendrite growth of multicomponent alloys in the low P6clet number regime is presented. The elimination of the mesh-induced anisotropy is achieved by adopting a modified virtual front tracking method. A new efficient method based on the lever rule is applied to calculate the solid fraction increment of the interfacial cells. The thermodynamic data such as liquidus temperature, the partition coefficients, and the slope of liquidus surface, needed for determining the dynamics of dendrite growth, are obtained by coupling with PanEngine. This model is applied to simulate the dendrite morphology and microsegregation of A1-Cu-Mg temary alloy both for single and multi- dendrites growth. The simulated results demonstrate that the difference of the concentration distribution profiles ahead of the dendrite tip for each alloying element mainly results from the different partition coefficients and solute diffusion coefficients. Comparison with the prediction of analytical model is carded out and it reveals the correctness of the model. Consequently, the difference in interdendritic microsegregation behavior of different components is analyzed.
基金financially supported by the National Key R&D Program of China (No.2017YFB0701503)the National Basic Research Program of China(No.2011CB706801)
文摘In the present investigation, a coupled crystal plasticity finite-element(CPFE) and cellular automaton(CA) model was developed to predict the microstructure of recrystallization in single-crystal(SX) Ni-based superalloy.The quasi-static compressive tests of [001] orientated SX DD6 superalloy were conducted on Gleeble3500 tester to calibrate the CPFE model based on crystal slip kinematics.The simulated stress-strain curve agrees well with the experimental results. Quantitative deformation amount was introduced in the deformed samples of simulation and experiment, and these samples were subsequently subjected to the standard solution heat treatment(SSHT).Results of CA simulation show that the recrystallization(RX) nucleation tends to occur at the third stage of SSHT process due to the high critical temperature of RX nucleation for the samples deformed at room temperature. The inhomogeneous RX grains gradually coarsen and compete to reach more stable status by reducing the system energy.Simulated RX grain density decreases from 7.500 to1.875 mm,agreeing well with the value of 1.920 mmfrom electron backscattered diffraction(EBSD) detection of the experimental sample.
基金financially supported by the National Key Research and Development Program of China(No.2017YFB0701503)the National Science and Technology Major Project(No.2017ZX04014001)the National Natural Science Foundation of China(No.51374137).
文摘The thermosolutal convection can alter segregation pattern,change dendrite morphology and even cause freckles formation in alloy solidification.In this work,the multiphase-field model was coupled with lattice Boltzmann method to simulate the dendrite growth under melt convection in superalloy solidification.In the isothermal solidification simulations,zero and normal gravitational accelerations were applied to investigate the effects of gravity on the dendrite morphology and the magnitude of melt flow.The solute distribution of each alloy component along with the dendrite tip velocity during solidification was obtained,and the natural convection has been confirmed to affect the microsegregation pattern and the dendrite growth velocity.In the directional solidification simulations,two typical temperature gradients were applied,and the dendrite morphology and fluid velocity in the mushy zone during solidification were analyzed.It is found that the freckles will form when the average fluid velocity in the mushy zone exceeds the withdraw velocity.
