Developing a molten salt reactor needs molten salt-impermeable nuclear graphite. Ultra-fine grain graphite is a good choice as it is better in permeability than fine grain graphite. In this paper, ultra-fine grain gra...Developing a molten salt reactor needs molten salt-impermeable nuclear graphite. Ultra-fine grain graphite is a good choice as it is better in permeability than fine grain graphite. In this paper, ultra-fine grain graphite(HPG-510) and fine grain graphite(IG-110) samples are irradiated at room temperature by 7 MeV Xe ions to doses of 1 × 10^(14)-5 × 10^(15) ions/cm^2. Scanning electron microscopy, transmission electron microscopy(TEM), Raman spectroscopy and nano-indentation are used to study the radiation-induced changes. After irradiation of different doses, all the HPG-510 samples show less surface fragment than the IG-110 samples. The TEM and Raman spectra,and the hardness and modulus characterized by nano-indentation, also indicate that HPG-510 is more resistant to irradiation.展开更多
The effect of long-term thermal exposure on the grain boundary carbides and the tensile behavior of two kinds of Ni–Mo–Cr superalloys with different silicon contents(0 and 0.46 wt%) was investigated. Experimental re...The effect of long-term thermal exposure on the grain boundary carbides and the tensile behavior of two kinds of Ni–Mo–Cr superalloys with different silicon contents(0 and 0.46 wt%) was investigated. Experimental results showed granular M2C carbides formed at the grain boundaries after exposure for 100 h for the non-silicon alloy. Furthermore, these fine granular M2C carbides will transform into plate-like M6C carbides as exposure time increases. For the Si-containing alloys,only the granular M6C carbides formed at the grain boundaries during the whole exposure time. The coarsening of the grain boundary carbides occurred in both alloys with increasing exposure time. In addition, the coarsening kinetics of the grain boundary carbides for the non-silicon alloy is faster than that of the standard alloy. The tensile properties of both alloys are improved after exposure for 100 h due to the formation of nano-sized grain boundary carbides. The grain boundary carbides are coarsened more seriously for non-silicon alloys than that of Si-containing alloys, resulting in a more significant decrease in the tensile strength and elongation for the former case. Silicon additions can effectively inhibit the severe coarsening of the grain boundary carbides and thus avoid the obvious deterioration of the tensile properties after a long-term thermal exposure.展开更多
Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure...Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.展开更多
Irradiation effects in Ni–17Mo–7Cr alloy have been systematically investigated by using 3 Me V Au ions at different fluences ranging from 8 9 1013cm-2to 2.3 9 1015cm-2,corresponding to doses of 1–30 dpa.The results...Irradiation effects in Ni–17Mo–7Cr alloy have been systematically investigated by using 3 Me V Au ions at different fluences ranging from 8 9 1013cm-2to 2.3 9 1015cm-2,corresponding to doses of 1–30 dpa.The results indicated that sample microstrain increased gradually from 0.14 to 0.22% as dose increased from 0 to 30 dpa.Besides,the nanohardness of Ni–17Mo–7Cr alloy increased with irradiation dose until 10 dpa,and then,softening effect became dominant while further increasing dose to 30 dpa.After being irradiated at room temperature,the swelling rate of Ni–17Mo–7Cr alloy was found to be around 0.04% per dpa.These data are helpful in estimating the irradiation resistance of this newly developed Ni–17Mo–7Cr alloy in nuclear energy systems.展开更多
Corrosion test of a Ni–16Mo–7Cr alloy with a decarburized layer was conducted in FLiNaK salt at 700 °C. A detailed microstructure study was performed to investigate the corrosion behavior and mechanisms. The re...Corrosion test of a Ni–16Mo–7Cr alloy with a decarburized layer was conducted in FLiNaK salt at 700 °C. A detailed microstructure study was performed to investigate the corrosion behavior and mechanisms. The results show that the Ferich layers were formed on the corroded alloys with and without decarburization. The surface decarburization had little influence on the corrosion resistance of the alloy, whereas it caused more M_2C carbide formation beneath the corrosion layer. That is attributed to the higher concentration of C gradient near the alloy surface, which was resulted from the increase in C content liberated from graphite crucible wall during the corrosion process.展开更多
基金supported by the Program of International S&T Cooperation of China(No.2014DFG60230)the National Natural Science Foundation of China(No.11305240)the"Strategic Priority Research Program"of the Chinese Academy of Sciences(No.XDA02040200)
文摘Developing a molten salt reactor needs molten salt-impermeable nuclear graphite. Ultra-fine grain graphite is a good choice as it is better in permeability than fine grain graphite. In this paper, ultra-fine grain graphite(HPG-510) and fine grain graphite(IG-110) samples are irradiated at room temperature by 7 MeV Xe ions to doses of 1 × 10^(14)-5 × 10^(15) ions/cm^2. Scanning electron microscopy, transmission electron microscopy(TEM), Raman spectroscopy and nano-indentation are used to study the radiation-induced changes. After irradiation of different doses, all the HPG-510 samples show less surface fragment than the IG-110 samples. The TEM and Raman spectra,and the hardness and modulus characterized by nano-indentation, also indicate that HPG-510 is more resistant to irradiation.
基金financially supported by the program of International S&T Cooperation, ANSTO-SINAP (No. 2014DFG60230)the National Natural Science Foundation of China (No. 51371188)+1 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences (No. XDA02004210)Science and Technology Commission of Shanghai Municipality (No. 11JC1414900)
文摘The effect of long-term thermal exposure on the grain boundary carbides and the tensile behavior of two kinds of Ni–Mo–Cr superalloys with different silicon contents(0 and 0.46 wt%) was investigated. Experimental results showed granular M2C carbides formed at the grain boundaries after exposure for 100 h for the non-silicon alloy. Furthermore, these fine granular M2C carbides will transform into plate-like M6C carbides as exposure time increases. For the Si-containing alloys,only the granular M6C carbides formed at the grain boundaries during the whole exposure time. The coarsening of the grain boundary carbides occurred in both alloys with increasing exposure time. In addition, the coarsening kinetics of the grain boundary carbides for the non-silicon alloy is faster than that of the standard alloy. The tensile properties of both alloys are improved after exposure for 100 h due to the formation of nano-sized grain boundary carbides. The grain boundary carbides are coarsened more seriously for non-silicon alloys than that of Si-containing alloys, resulting in a more significant decrease in the tensile strength and elongation for the former case. Silicon additions can effectively inhibit the severe coarsening of the grain boundary carbides and thus avoid the obvious deterioration of the tensile properties after a long-term thermal exposure.
基金supported by the China-Australia Joint Research Project (Grant No.2014DFG60230)Knowledge Innovation program of Chinese Academy of Sciences and National Basic Research Program of China (Grant No.2010CB832903 and 2010CB834503)
文摘Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.
基金supported by the ChinaAustralia Joint Research Project (Grant No.2014DFG60230)the Joint Fund of the National Natural Science Foundation of China and the China Academy of Engineering Physics (Grant No.U1230111)the National Natural Science Foundation of China (Grant No.91226202)
文摘Irradiation effects in Ni–17Mo–7Cr alloy have been systematically investigated by using 3 Me V Au ions at different fluences ranging from 8 9 1013cm-2to 2.3 9 1015cm-2,corresponding to doses of 1–30 dpa.The results indicated that sample microstrain increased gradually from 0.14 to 0.22% as dose increased from 0 to 30 dpa.Besides,the nanohardness of Ni–17Mo–7Cr alloy increased with irradiation dose until 10 dpa,and then,softening effect became dominant while further increasing dose to 30 dpa.After being irradiated at room temperature,the swelling rate of Ni–17Mo–7Cr alloy was found to be around 0.04% per dpa.These data are helpful in estimating the irradiation resistance of this newly developed Ni–17Mo–7Cr alloy in nuclear energy systems.
基金supported financially by the National Natural Science Foundation of China (Nos. 51601214, 51674237 and 11705264)the National Key Research and Development Program (No. 2017YFA0402803)
文摘Corrosion test of a Ni–16Mo–7Cr alloy with a decarburized layer was conducted in FLiNaK salt at 700 °C. A detailed microstructure study was performed to investigate the corrosion behavior and mechanisms. The results show that the Ferich layers were formed on the corroded alloys with and without decarburization. The surface decarburization had little influence on the corrosion resistance of the alloy, whereas it caused more M_2C carbide formation beneath the corrosion layer. That is attributed to the higher concentration of C gradient near the alloy surface, which was resulted from the increase in C content liberated from graphite crucible wall during the corrosion process.
