The microstructures and properties of hot-rolled low-carbon ferritic steel have been investigated by optical microscopy, field-emission scanning electron microscopy, transmission electron microscopy, and tensile tests...The microstructures and properties of hot-rolled low-carbon ferritic steel have been investigated by optical microscopy, field-emission scanning electron microscopy, transmission electron microscopy, and tensile tests after isothermal transformation from 600°C to 700°C for 60 min. It is found that the strength of the steel decreases with the increment of isothermal temperature, whereas the hole expansion ratio and the fraction of high-angle grain boundaries increase. A large amount of nanometer-sized carbides were homogeneously distributed throughout the material, and fine（Ti, Mo）C precipitates have a significant precipitation strengthening effect on the ferrite phase because of their high density. The nanometer-sized carbides have a lattice parameter of 0.411-0.431 nm. After isothermal transformation at 650°C for 60 min, the ferrite phase can be strengthened above 300 MPa by precipitation strengthening according to the Ashby-Orowan mechanism.展开更多
The microstructures and mechanical properties of C-Mn-Cr-Nb and C-Mn-Si-Nb ultra-high strength dual-phase steels were studied by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and tens...The microstructures and mechanical properties of C-Mn-Cr-Nb and C-Mn-Si-Nb ultra-high strength dual-phase steels were studied by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and tensile test. The results show that Si can promote the transformation of austenite （γ） to ferrite （α）, enlarge the （α＋γ） region, and increase the aging stability of martensite by inhibiting carbide precipitation. Adding Cr leads to the formation of retained austenite and martensite/austenite （M/A） constituents, as well as the decomposi- tion of martensite during the overaging stage. Both of the steels show higher initial strain-hardening rates and two-stage strain-hardening characteristics. The C-Mn-Si-Nb steel shows the higher strain-hardening rate than the C-Mn-Cr-Nb steel in the first stage; however, there is no significant difference in the second stage. Although the tensile strength and elongation of the two steels both exceed 1000 MPa and 15%, respectively, the comprehensive mechanical properties of the C-Mn-Si-Nb steel are superior.展开更多
The transformation behavior and tensile properties of an ultra-high-strength transformation-induced plasticity （TRIP） steel （0.2C-2.0Si-I.SMn） were investigated by different heat treatments for automobile applicat...The transformation behavior and tensile properties of an ultra-high-strength transformation-induced plasticity （TRIP） steel （0.2C-2.0Si-I.SMn） were investigated by different heat treatments for automobile applications. The results show that F-TRIP steel, a tradi- tional TRIP steel containing as-cold-rolled ferfite and pearlite as the original microstructure, consists of equiaxed grains of intercritical ferrite surrounded by discrete particles of M/RA and B. In contrast, M-TRIP steel, a modified TRiP-aided steel with martensite as the original mi- crostlucture, containing full martensite as the original microstructure is comprised of lath-shaped grains of ferrite separated by lath-shaped martensite/retained austenite and bainite. Most of the austenite in F-TRIP steel is granular, while the austenite in M-TRIP steel is lath-shaped. The volume fraction of the retained austenite as well as its carbon content is lower in F-TRIP steel than in M-TRIP steel, and austenite grains in M-TRIP steel are much finer than those in F-TRIP steel. Therefore, M-TRIP steel was concluded to have a higher austenite stability, re- sulting in a lower transformation rate and consequently contributing to a higher elongation compared to F-TRIP steel. Work hardening be- havior is also discussed for both types of steel.展开更多
The effects of Cr contents(0.3 and 1.0 wt.%)and isothermal holding temperatures(400,440,and 480℃)on the microstructure evolution and properties of complex phase steel with high formability(CH steel)were investigated ...The effects of Cr contents(0.3 and 1.0 wt.%)and isothermal holding temperatures(400,440,and 480℃)on the microstructure evolution and properties of complex phase steel with high formability(CH steel)were investigated using dilatometry,scanning electron microscopy,transmission electron microscopy(TEM),and X-ray diffraction.The results show that the microstructures of CH steel with 0.3 wt.%Cr are ferrite,granular bainite,martensite,and retained austenite,while no ferrite is observed in the microstructure of CH steel with 1.0 wt.%Cr in the same process.Cr promotes the precipitation of(Nb,Ti)C in the high-temperature austenite region through theoretical calculations and TEM observations.Cr retards the bainite transformation and refines the grain size of CH steel.Furthermore,as isothermal holding temperature increases from 400 to 480℃,the bainite and retained austenite fractions of two CH steels decrease,while the martensite fraction increases in the steels after final quenching.Consequently,the strength has an increasing tendency and the total elongation has a decreasing tendency with increasing isothermal temperature.展开更多
The quenching and partitioning steel is the representative of the third generation of advanced high-strength steel.The effect of quenching temperature on the microstructure and mechanical property of ferrite-containin...The quenching and partitioning steel is the representative of the third generation of advanced high-strength steel.The effect of quenching temperature on the microstructure and mechanical property of ferrite-containing quenching and partitioning steel was studied by intercritical annealing quenching and partitioning processes.When preparing a test steel with a tensile strength of 1300 MPa and total elongation of 19%,it is found that the actual optimum quenching temperature was lower than that calculated according to the constrained carbon equilibrium.The results indicate that the martensite start temperature of the austenite was overestimated when considering the diffusion of carbon only.Austenite grain size which is affected by low temperature and the existence of ferrite during intercritical annealing influenced the optimum quenching temperature.A scheme considering the diffusion of various alloying elements and austenite grain size was proposed and verified.Using this scheme,the optimum quenching temperature of intercritically annealed quenching and partitioning steel with complex microstructures was well predicted.展开更多
The mechanical properties of the hot-rolled plates of Ti steel and Ti-Mo steel after isothermal transformation in a temperature range of 600 700 ℃ for 60 min have been tested, and the microstructures of the matrix an...The mechanical properties of the hot-rolled plates of Ti steel and Ti-Mo steel after isothermal transformation in a temperature range of 600 700 ℃ for 60 min have been tested, and the microstructures of the matrix and the characteristics of precipitated nanometer-sized carbides have also been examined by scanning electron microscopy and transmission electron microscopy. The precipitation regularity of nanometer-sized carbides has been studied by thermodynamic method and the contributions of corresponding strengthening mechanisms to the total yield strength have been calculated. The tensile strength of hot-rolled Ti-Mo ferritie steel can achieve 780 MPa with an elongation of 20.0% after being isothermally treated at 600 ℃ for 60 rain, and the tensile strength of Ti steel is 605 MPa with an elongation of 22.7%, according to the results of tensile tests. The critical nucleation size of （Ti,Mo）C is smaller than that of TiC at a given isothermal temperature, but the nucleation rate of （Ti, Mo）C is larger than that of TiC. The grainrefinement strengthening and precipitation strengthening contribute the main amount of the total yield strength. The major increase in yield strength with the decrease of isothermal temperature results from the contribution of precipi tation strengthening. The contribution of precipitation strengthening to the yield strength of the steels has been esti mated. The ferrite phase can be strengthened by about 400 MPa through precipitation strengthening in Ti-Mo steel isothermally treated at 600 ℃ for 60 rain, which is about 200 MPa higher than that of Ti steel under the same conditions.展开更多
The microstructure characteristics and properties(especially hole expansion property)of 800 MPa hot-rolled complex phase steel with different coiling temperatures were studied.The microstructure consisted of polygonal...The microstructure characteristics and properties(especially hole expansion property)of 800 MPa hot-rolled complex phase steel with different coiling temperatures were studied.The microstructure consisted of polygonal ferrite and precipitates when the steel was coiled at 550℃,and when the steel was coiled between 460–520℃,the microstructure was composed of granular bainite and martensite and austenite(M/A)islands.The morphology of the crack was analyzed by scanning electron microscopy,and the in situ scanning electron microscope tensile test was used to find out the fracture mechanism and deformation behavior of the steel with different coiling temperatures.When the steel was coiled at 550℃,the cracks initiated at the ferrite grain boundary and propagated through the grains or along the grain boundaries.When the steel was coiled at 520℃,the cracks first initiated at the junction of ferrite and M/A island and then propagated through the grains.The steel coiled at 520℃ has quite good mechanical properties and relatively high hole expansion ratio.展开更多
To develop super-high strength TRIP steel for automobile application with good combination of strength and plasticity, an ultra high-strength TRIP steel 0.2 %C-2.0% Si-1.8% Mn was investigated at different intercritic...To develop super-high strength TRIP steel for automobile application with good combination of strength and plasticity, an ultra high-strength TRIP steel 0.2 %C-2.0% Si-1.8% Mn was investigated at different intercritical annealing temperatures and bainitic isothermal temperatures. Microstructures were observed by scanning electron mi- croscopy, transmission electron microscopy, electron backscatter diffraction, and X-ray diffraction, and mechanical properties were tested under a uniaxial tensile testing machine. It shows that the best comprehensive mechanical properties were obtained for the experimental steel particularly annealed at 820 ℃ and austempered at 410 ℃. Yield strength of the tested steel mainly depends on ferrite, while the high strength of the tested steel is related to mar- tensite which forms through blocky austenite transformation during cooling and subsequent tensile test attributed to the TRIP effect. Hence, it could be concluded that the grain size of the retained austenite and carbon content in re- tained austenite are the main reasons for high elongation of the tested steel.展开更多
Based on the chemical composition of traditional hot-stamped steel(e.g.,22MnB5 and 30MnB5),Nb and V microalloying elements are added into 30MnB5 steel to meet the requirements of ultra-high strength,excellent ductilit...Based on the chemical composition of traditional hot-stamped steel(e.g.,22MnB5 and 30MnB5),Nb and V microalloying elements are added into 30MnB5 steel to meet the requirements of ultra-high strength,excellent ductility and potent resistance to hydrogen embrittlement(HE)at the same time.The influence of hot-stamped steel on HE was studied by conducting a hydrogen permeation method and pre-charged hydrogen slow strain rate test.Meanwhile,the experimental steel microstructures and corresponding fracture surfaces are observed and analyzed to characterize HE behavior.The results show that a finer microstructure,a lower apparent diffusion coefficient of hydrogen and a smaller percentage of strength and plasticity reduction are obtained due to the addition of the vanadium element into hot-stamped steel.Compared to the V free experimental steel,the steel with 0.14 wt.% V has a large number of dispersive precipitates and more grain boundary areas,which makes hydrogen atoms dispersedly distribute.展开更多
The Fe-0.21C 2.2Mn 0.49Si-1.77A1 transformation induced plasticity （TRIP） aided steel was heat trea- ted at various austenitizing temperatures under both TRiP-aided polygonal ferrite type （TPF） and an- nealed mart...The Fe-0.21C 2.2Mn 0.49Si-1.77A1 transformation induced plasticity （TRIP） aided steel was heat trea- ted at various austenitizing temperatures under both TRiP-aided polygonal ferrite type （TPF） and an- nealed martensite matrix （TAM） processes. The microstructure evolution and their effects on mechanical properties were systematically investigated through the microstructure observation and dilatometric analysis. The microstructure homogeneity is improved in TPF steel heated at a high temperature due to the reduced banded martensite and the increased bainite. Compared with the mechanical properties of the TPF steels, the yield strength and elongation of the TAM steels are much higher, while the tensile strength is lower than that of TPF steels. The stability of intercritical austenite is affected by the heating tempera- ture, and thus the following phase transformation influences the mechanical properties, such as the bain- ite transformation and the precipitation of polygonal ferrite. Obvious dynamic bainite transformation occurs at TAM850, TAM900 and TAM950, More proportion of polygonal ferrite is found in the sample heated at 950 ℃. The bainite transformation beginning at a higher temperature results in the wider bainitic ferrite laths. The more proportion of polygonal ferrite and wide bainitic ferrite laths commonly contribute to the lower strength and better elongation. The uniform microstructure with lath-like morphology and retained austenite with high average carbon content ensures a good mechanical property in TAM850 with the product of strength and elongation of about 28 GPa ·%,展开更多
The influence of microstructural characteristics on Lu¨ders strain and mechanical properties was explored by means of altering thermo-mechanical circumstances in an intercritical annealing(IA)medium-Mn Fe-11Mn-0....The influence of microstructural characteristics on Lu¨ders strain and mechanical properties was explored by means of altering thermo-mechanical circumstances in an intercritical annealing(IA)medium-Mn Fe-11Mn-0.09C-0.25Si(wt.%)steel.By IA of cold-rolled samples with severe plastic deformation,exclusively equiaxed dual phases were obtained because of active recovery and recrystallization.The equiaxed austenite(gamma E)with a larger size and inadequate chemical concentration was more readily transformed into martensite,and subsequent transformation-induced plasticity(TRIP)effect was triggered actively at relatively higher IA temperature,lessening localized deformation.In addition,grown-in dislocations were prone to multiply and migrate around a broad mean free path for coarser equiaxed ferrite(alpha E)due to weakening dynamic recovery;therefore,it was the ensuing increased mobility of dislocations instead of reserving plentiful initial dislocation density that facilitated the propagation velocity of Luders bands and the accumulation of work hardening.In contrast,the bimodal-grained microstructure with lath-like and equiaxed austenite(gamma L+gamma E)satisfactorily contributed to a smaller yield point elongation(YPE)without compromise of comprehensive mechanical properties on the grounds that austenitic gradient stability gave rise to discontinuous but sustainable TRIP effect and incremental work hardening.Hence,Luders strain is closely related to the absence of work hardening in the region which yields locally.It follows that the decreased stability of retained austenite,favorable mobility of dislocations and the bimodal-grained structure all prominently make up for the insufficiency of work hardening,thereof resulting in a limited YPE.展开更多
基金financial support by the National Natural Science Foundation of China (No. 51271035)the Specialized Research Fund for the Doctoral Program of Higher Education of China (No. 20110006110007)
文摘The microstructures and properties of hot-rolled low-carbon ferritic steel have been investigated by optical microscopy, field-emission scanning electron microscopy, transmission electron microscopy, and tensile tests after isothermal transformation from 600°C to 700°C for 60 min. It is found that the strength of the steel decreases with the increment of isothermal temperature, whereas the hole expansion ratio and the fraction of high-angle grain boundaries increase. A large amount of nanometer-sized carbides were homogeneously distributed throughout the material, and fine（Ti, Mo）C precipitates have a significant precipitation strengthening effect on the ferrite phase because of their high density. The nanometer-sized carbides have a lattice parameter of 0.411-0.431 nm. After isothermal transformation at 650°C for 60 min, the ferrite phase can be strengthened above 300 MPa by precipitation strengthening according to the Ashby-Orowan mechanism.
基金financially supported by the National Natural Science Foundation of China(No.50904006)the Fundamental Research Funds for the Central Universities of China(No.FRT-TP-10-001A)
文摘The microstructures and mechanical properties of C-Mn-Cr-Nb and C-Mn-Si-Nb ultra-high strength dual-phase steels were studied by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and tensile test. The results show that Si can promote the transformation of austenite （γ） to ferrite （α）, enlarge the （α＋γ） region, and increase the aging stability of martensite by inhibiting carbide precipitation. Adding Cr leads to the formation of retained austenite and martensite/austenite （M/A） constituents, as well as the decomposi- tion of martensite during the overaging stage. Both of the steels show higher initial strain-hardening rates and two-stage strain-hardening characteristics. The C-Mn-Si-Nb steel shows the higher strain-hardening rate than the C-Mn-Cr-Nb steel in the first stage; however, there is no significant difference in the second stage. Although the tensile strength and elongation of the two steels both exceed 1000 MPa and 15%, respectively, the comprehensive mechanical properties of the C-Mn-Si-Nb steel are superior.
基金financially supported by the National Natural Science Foundation of China (No. 51271035)The financial support of the Beijing Laboratory of Metallic Materials and Processing for Modern Transportation
文摘The transformation behavior and tensile properties of an ultra-high-strength transformation-induced plasticity （TRIP） steel （0.2C-2.0Si-I.SMn） were investigated by different heat treatments for automobile applications. The results show that F-TRIP steel, a tradi- tional TRIP steel containing as-cold-rolled ferfite and pearlite as the original microstructure, consists of equiaxed grains of intercritical ferrite surrounded by discrete particles of M/RA and B. In contrast, M-TRIP steel, a modified TRiP-aided steel with martensite as the original mi- crostlucture, containing full martensite as the original microstructure is comprised of lath-shaped grains of ferrite separated by lath-shaped martensite/retained austenite and bainite. Most of the austenite in F-TRIP steel is granular, while the austenite in M-TRIP steel is lath-shaped. The volume fraction of the retained austenite as well as its carbon content is lower in F-TRIP steel than in M-TRIP steel, and austenite grains in M-TRIP steel are much finer than those in F-TRIP steel. Therefore, M-TRIP steel was concluded to have a higher austenite stability, re- sulting in a lower transformation rate and consequently contributing to a higher elongation compared to F-TRIP steel. Work hardening be- havior is also discussed for both types of steel.
基金The authors gratefully acknowledge the support from the Key Research and Development Plan of Shandong Province(No.2019TSLH0103)the New Energy Automobile Material Production and Application Demonstration Platform Project(No.TC180A6MR-1)Guangxi Innovation-Driven Development Special Fund Project(No.AA18242012).
文摘The effects of Cr contents(0.3 and 1.0 wt.%)and isothermal holding temperatures(400,440,and 480℃)on the microstructure evolution and properties of complex phase steel with high formability(CH steel)were investigated using dilatometry,scanning electron microscopy,transmission electron microscopy(TEM),and X-ray diffraction.The results show that the microstructures of CH steel with 0.3 wt.%Cr are ferrite,granular bainite,martensite,and retained austenite,while no ferrite is observed in the microstructure of CH steel with 1.0 wt.%Cr in the same process.Cr promotes the precipitation of(Nb,Ti)C in the high-temperature austenite region through theoretical calculations and TEM observations.Cr retards the bainite transformation and refines the grain size of CH steel.Furthermore,as isothermal holding temperature increases from 400 to 480℃,the bainite and retained austenite fractions of two CH steels decrease,while the martensite fraction increases in the steels after final quenching.Consequently,the strength has an increasing tendency and the total elongation has a decreasing tendency with increasing isothermal temperature.
基金The authors gratefully acknowledge the support of the National Key Research and Development Program of Thirteenth Five-Year Plan Period(Grant No.2017YFB0304400)Production and Application Demonstration Platform of New Energy Automotive Material(Grant No.TC180A6MR-1).
文摘The quenching and partitioning steel is the representative of the third generation of advanced high-strength steel.The effect of quenching temperature on the microstructure and mechanical property of ferrite-containing quenching and partitioning steel was studied by intercritical annealing quenching and partitioning processes.When preparing a test steel with a tensile strength of 1300 MPa and total elongation of 19%,it is found that the actual optimum quenching temperature was lower than that calculated according to the constrained carbon equilibrium.The results indicate that the martensite start temperature of the austenite was overestimated when considering the diffusion of carbon only.Austenite grain size which is affected by low temperature and the existence of ferrite during intercritical annealing influenced the optimum quenching temperature.A scheme considering the diffusion of various alloying elements and austenite grain size was proposed and verified.Using this scheme,the optimum quenching temperature of intercritically annealed quenching and partitioning steel with complex microstructures was well predicted.
基金Sponsored by National Natural Science Foundation of China(51271035)
文摘The mechanical properties of the hot-rolled plates of Ti steel and Ti-Mo steel after isothermal transformation in a temperature range of 600 700 ℃ for 60 min have been tested, and the microstructures of the matrix and the characteristics of precipitated nanometer-sized carbides have also been examined by scanning electron microscopy and transmission electron microscopy. The precipitation regularity of nanometer-sized carbides has been studied by thermodynamic method and the contributions of corresponding strengthening mechanisms to the total yield strength have been calculated. The tensile strength of hot-rolled Ti-Mo ferritie steel can achieve 780 MPa with an elongation of 20.0% after being isothermally treated at 600 ℃ for 60 rain, and the tensile strength of Ti steel is 605 MPa with an elongation of 22.7%, according to the results of tensile tests. The critical nucleation size of （Ti,Mo）C is smaller than that of TiC at a given isothermal temperature, but the nucleation rate of （Ti, Mo）C is larger than that of TiC. The grainrefinement strengthening and precipitation strengthening contribute the main amount of the total yield strength. The major increase in yield strength with the decrease of isothermal temperature results from the contribution of precipi tation strengthening. The contribution of precipitation strengthening to the yield strength of the steels has been esti mated. The ferrite phase can be strengthened by about 400 MPa through precipitation strengthening in Ti-Mo steel isothermally treated at 600 ℃ for 60 rain, which is about 200 MPa higher than that of Ti steel under the same conditions.
基金This work was supported by the Foundation of China Electric Power Research Institute(No.51601174).
文摘The microstructure characteristics and properties(especially hole expansion property)of 800 MPa hot-rolled complex phase steel with different coiling temperatures were studied.The microstructure consisted of polygonal ferrite and precipitates when the steel was coiled at 550℃,and when the steel was coiled between 460–520℃,the microstructure was composed of granular bainite and martensite and austenite(M/A)islands.The morphology of the crack was analyzed by scanning electron microscopy,and the in situ scanning electron microscope tensile test was used to find out the fracture mechanism and deformation behavior of the steel with different coiling temperatures.When the steel was coiled at 550℃,the cracks initiated at the ferrite grain boundary and propagated through the grains or along the grain boundaries.When the steel was coiled at 520℃,the cracks first initiated at the junction of ferrite and M/A island and then propagated through the grains.The steel coiled at 520℃ has quite good mechanical properties and relatively high hole expansion ratio.
基金Item Sponsored by National Natural Science Foundation of China(51271035)
文摘To develop super-high strength TRIP steel for automobile application with good combination of strength and plasticity, an ultra high-strength TRIP steel 0.2 %C-2.0% Si-1.8% Mn was investigated at different intercritical annealing temperatures and bainitic isothermal temperatures. Microstructures were observed by scanning electron mi- croscopy, transmission electron microscopy, electron backscatter diffraction, and X-ray diffraction, and mechanical properties were tested under a uniaxial tensile testing machine. It shows that the best comprehensive mechanical properties were obtained for the experimental steel particularly annealed at 820 ℃ and austempered at 410 ℃. Yield strength of the tested steel mainly depends on ferrite, while the high strength of the tested steel is related to mar- tensite which forms through blocky austenite transformation during cooling and subsequent tensile test attributed to the TRIP effect. Hence, it could be concluded that the grain size of the retained austenite and carbon content in re- tained austenite are the main reasons for high elongation of the tested steel.
基金the National Natural Science Foundation of China(Grant No.51574028)the Development Program of Thirteenth Five-year Plan Period(Grant No.2017 YFB0304400)for Grant and financial support.
文摘Based on the chemical composition of traditional hot-stamped steel(e.g.,22MnB5 and 30MnB5),Nb and V microalloying elements are added into 30MnB5 steel to meet the requirements of ultra-high strength,excellent ductility and potent resistance to hydrogen embrittlement(HE)at the same time.The influence of hot-stamped steel on HE was studied by conducting a hydrogen permeation method and pre-charged hydrogen slow strain rate test.Meanwhile,the experimental steel microstructures and corresponding fracture surfaces are observed and analyzed to characterize HE behavior.The results show that a finer microstructure,a lower apparent diffusion coefficient of hydrogen and a smaller percentage of strength and plasticity reduction are obtained due to the addition of the vanadium element into hot-stamped steel.Compared to the V free experimental steel,the steel with 0.14 wt.% V has a large number of dispersive precipitates and more grain boundary areas,which makes hydrogen atoms dispersedly distribute.
基金funded by National Natural Science Foundation of China(51574028)
文摘The Fe-0.21C 2.2Mn 0.49Si-1.77A1 transformation induced plasticity （TRIP） aided steel was heat trea- ted at various austenitizing temperatures under both TRiP-aided polygonal ferrite type （TPF） and an- nealed martensite matrix （TAM） processes. The microstructure evolution and their effects on mechanical properties were systematically investigated through the microstructure observation and dilatometric analysis. The microstructure homogeneity is improved in TPF steel heated at a high temperature due to the reduced banded martensite and the increased bainite. Compared with the mechanical properties of the TPF steels, the yield strength and elongation of the TAM steels are much higher, while the tensile strength is lower than that of TPF steels. The stability of intercritical austenite is affected by the heating tempera- ture, and thus the following phase transformation influences the mechanical properties, such as the bain- ite transformation and the precipitation of polygonal ferrite. Obvious dynamic bainite transformation occurs at TAM850, TAM900 and TAM950, More proportion of polygonal ferrite is found in the sample heated at 950 ℃. The bainite transformation beginning at a higher temperature results in the wider bainitic ferrite laths. The more proportion of polygonal ferrite and wide bainitic ferrite laths commonly contribute to the lower strength and better elongation. The uniform microstructure with lath-like morphology and retained austenite with high average carbon content ensures a good mechanical property in TAM850 with the product of strength and elongation of about 28 GPa ·%,
基金the support of the National Key Research and Development Program of Thirteenth Five-Year Plan Period(Grant No.2017YFB0304400)the National Natural Science Foundation of China(Grant No.51574028).
文摘The influence of microstructural characteristics on Lu¨ders strain and mechanical properties was explored by means of altering thermo-mechanical circumstances in an intercritical annealing(IA)medium-Mn Fe-11Mn-0.09C-0.25Si(wt.%)steel.By IA of cold-rolled samples with severe plastic deformation,exclusively equiaxed dual phases were obtained because of active recovery and recrystallization.The equiaxed austenite(gamma E)with a larger size and inadequate chemical concentration was more readily transformed into martensite,and subsequent transformation-induced plasticity(TRIP)effect was triggered actively at relatively higher IA temperature,lessening localized deformation.In addition,grown-in dislocations were prone to multiply and migrate around a broad mean free path for coarser equiaxed ferrite(alpha E)due to weakening dynamic recovery;therefore,it was the ensuing increased mobility of dislocations instead of reserving plentiful initial dislocation density that facilitated the propagation velocity of Luders bands and the accumulation of work hardening.In contrast,the bimodal-grained microstructure with lath-like and equiaxed austenite(gamma L+gamma E)satisfactorily contributed to a smaller yield point elongation(YPE)without compromise of comprehensive mechanical properties on the grounds that austenitic gradient stability gave rise to discontinuous but sustainable TRIP effect and incremental work hardening.Hence,Luders strain is closely related to the absence of work hardening in the region which yields locally.It follows that the decreased stability of retained austenite,favorable mobility of dislocations and the bimodal-grained structure all prominently make up for the insufficiency of work hardening,thereof resulting in a limited YPE.
