This paper provided an effective method to further improve the mechanical properties of the AZ80+0.4%Ce magnesium alloy wheel spoke.The effect of high strength and ductility was obtained with a yield strength of 295.3...This paper provided an effective method to further improve the mechanical properties of the AZ80+0.4%Ce magnesium alloy wheel spoke.The effect of high strength and ductility was obtained with a yield strength of 295.36 MPa,an elongation of 10%,by the combination of pre-deformation(7%deformation)and two-stage aging treatment(120℃/9 h+175℃/24 h).The evolution of the microstructure and properties of the alloy was explored under the coupling conditions of different pre-deformation degrees and multi-stage aging.The results show that,pre-deformation introduced a large number of(1012)tensile twinning and dislocations,which greatly promoted the probability of continuous precipitates(CPs)appearing.On the contrary,the discontinuous precipitates(DPs)were limited by the vertical and horizontal twin structure.As a result,the pre-nucleation method of two-stage aging increased the proportion of CPs by 34%-38%.Owing to the DPs was effectively suppressed,the alloy's yield strength has been greatly improved.Besides,under multi-stage aging,the twin boundaries induce protruding nucleation to form static recrystallization by hindering the migration of dislocations,and the matrix swallows the twins,then the texture gradually tilts from the two poles to the basal plane.As an important supplement,the grain refinement and oblique texture promoted the improvement of the yield strength of the component.展开更多
The extruded AZ80+0.4%Ce magnesium alloy was twisted in the temperature range of 300-380℃by using a Gleeble 3500 thermal simulation test machine with a torsion unit.The deformed cylindrical specimens were cooled at a...The extruded AZ80+0.4%Ce magnesium alloy was twisted in the temperature range of 300-380℃by using a Gleeble 3500 thermal simulation test machine with a torsion unit.The deformed cylindrical specimens were cooled at a cooling rate of 10℃/s or 0.1℃/s,respectively,and aged at 170℃.The microstructure analysis results showed that the grain size decreased with increasing specimen radial position from center(SRPC),and that the strong initial basal texture of the extruded magnesium alloy was weakened.Both continuous and discontinuous dynamic recrystallization mechanisms were involved in contributing to the grain refinement for all specimens investigated.And a novel extension twinning induced dynamic recrystallization mechanism was proposed for specimen deformed at 300℃.For the specimens deformed at 300℃and 340℃followed by a slow cooling rate(0.1℃/s),precipitates of various shapes(β-Mg_(17)Al_(12)),with the dominant precipitates being on the grains boundaries,appeared on the surface section.For specimen deformed at 380℃,lamellar precipitates(LPS)in the interiors of the grains were predominant.After aging,the LPS still dominated for specimens twisted at 380℃;however,the LPS gradually decreased with decreasing deformation temperatures from 380℃to 300℃.Dynamically precipitatedβ,especially those decorating the grain boundaries,changed the competition pictures for the LPS and precipitates of other shapes after aging.Interestingly,LPS dominated the areas for the center section of the specimens after aging regardless of deformation temperatures.Low temperature deformation with high SRPC followed by rapid cooling rate increased the micro hardness of the alloy after aging due to refined grain,reduced precipitates size,decreased lamellar spacing as well as strain hardening.展开更多
The current single-atom catalysts(SACs)for medicine still suffer from the limited active site density.Here,we develop a synthetic method capable of increasing both the metal loading and mass-specific activity of SACs ...The current single-atom catalysts(SACs)for medicine still suffer from the limited active site density.Here,we develop a synthetic method capable of increasing both the metal loading and mass-specific activity of SACs by exchanging zinc with iron.The constructed iron SACs(h^(3)-FNC)with a high metal loading of 6.27 wt%and an optimized adjacent Fe distance of~4 A exhibit excellent oxidase-like catalytic performance without significant activity decay after being stored for six months and promising antibacterial effects.Attractively,a“density effect”has been found at a high-enough metal doping amount,at which individual active sites become close enough to interact with each other and alter the electronic structure,resulting in significantly boosted intrinsic activity of single-atomic iron sites in h^(3)-FNCs by 2.3 times compared to low-and medium-loading SACs.Consequently,the overall catalytic activity of h^(3)-FNC is highly improved,with mass activity and metal mass-specific activity that are,respectively,66 and 315 times higher than those of commercial Pt/C.In addition,h^(3)-FNCs demonstrate efficiently enhanced capability in catalyzing oxygen reduction into superoxide anion(O_(2)·^(−))and glutathione(GSH)depletion.Both in vitro and in vivo assays demonstrate the superior antibacterial efficacy of h^(3)-FNCs in promoting wound healing.This work presents an intriguing activity-enhancement effect in catalysts and exhibits impressive therapeutic efficacy in combating bacterial infections.展开更多
Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The ...Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The results indicated that the average grain sizes were refined forming gradient structure with increasing specimen radial position from center(12.2-5.4μm),and that the initial basal texture intensity of the extruded magnesium alloy was weakened from 46.2 to 8.3.Furthermore,the extension twins(ETs)could be disintegrated from the twins forming separated twins with smaller sizes.Interestingly,ETs with the same twin variant intersecting with each other could be coalesced forming grains with similar orientation,while ETs with different twin variants were separated by twins boundaries contributing to grain refinement.Moreover,in addition to the conventional continuous dynamic recrystallized(CDRX)grains with 30˚orientation rotated around C-axis of the parent grains,CDRXed grains with 30˚rotation around a-axis and random rotation axis were also discerned.Besides,the CDRX evolution induced twins were also elaborated,exhibiting the complex competition between CDRX and twining.Hot torsion deformation with constant decreasing temperatures rate is an effective way of grain refinement and texture modification.展开更多
Effective user authentication is key to ensuring equipment security,data privacy,and personalized services in Internet of Things(IoT)systems.However,conventional mode-based authentication methods(e.g.,passwords and sm...Effective user authentication is key to ensuring equipment security,data privacy,and personalized services in Internet of Things(IoT)systems.However,conventional mode-based authentication methods(e.g.,passwords and smart cards)may be vulnerable to a broad range of attacks(e.g.,eavesdropping and side-channel attacks).Hence,there have been attempts to design biometric-based authentication solutions,which rely on physiological and behavioral characteristics.Behavioral characteristics need continuous monitoring and specific environmental settings,which can be challenging to implement in practice.However,we can also leverage Artificial Intelligence(AI)in the extraction and classification of physiological characteristics from IoT devices processing to facilitate authentication.Thus,we review the literature on the use of AI in physiological characteristics recognition pub-lished after 2015.We use the three-layer architecture of the IoT(i.e.,sensing layer,feature layer,and algorithm layer)to guide the discussion of existing approaches and their limitations.We also identify a number of future research opportunities,which will hopefully guide the design of next generation solutions.展开更多
Stimulated emission depletion microscopy(STED)holds great potential in biological science applications,especially in studying nanoscale subcellular structures.However,multi-color STED imaging in live-cell remains chal...Stimulated emission depletion microscopy(STED)holds great potential in biological science applications,especially in studying nanoscale subcellular structures.However,multi-color STED imaging in live-cell remains challenging due to the limited excitation wavelengths and large amount of laser radiation.Here,we develop a multiplexed live-cell STED method to observe more structures simultaneously with limited photo-bleaching and photo-cytotoxicity.By separating live-cell fluorescent probes with similar spectral properties using phasor analysis,our method enables five-color live-cell STED imaging and reveals long-term interactions between different subcellular structures.The results here provide an avenue for understanding the complex and delicate interactome of subcellular structures in live-cell.展开更多
The lightweight of high-end equipment relies on high mechanical properties magnesium(Mg) alloy structural components, because it is the best way to improve equipment service performance and reduce energy consumption. ...The lightweight of high-end equipment relies on high mechanical properties magnesium(Mg) alloy structural components, because it is the best way to improve equipment service performance and reduce energy consumption. This article summarizes the current progress and characteristics of large-scale high-performance Mg alloy components by analyzing the strengthening-toughening mechanisms, characteristics of plastic forming, and the preparation of large high mechanical properties forging blanks. Due to the lack of breakthroughs in the key technologies for forming large-scale Mg alloy components, their uniformity of mechanical properties and consistency are poor, the forming accuracy of components is low, and the production cost is high, which limit their engineering application and restrict the lightweight level of high-end equipment. In view of the above problems, the forming trends and research directions of large-scale and high mechanical properties Mg alloy components are proposed in this paper. It can provide help for the breakthrough of the key technology of large-scale Mg alloy components with high mechanical properties and expand the application of Mg alloy in high-end products.展开更多
RE-containing magnesium alloys were prepared via molten-salt-mediated magnesiothermic reduction by using RE_(2)O_(3)(RE=Y,Nd and Gd)and Mg metal as raw materials.The thermomechanical analysis of the magnesiothermic re...RE-containing magnesium alloys were prepared via molten-salt-mediated magnesiothermic reduction by using RE_(2)O_(3)(RE=Y,Nd and Gd)and Mg metal as raw materials.The thermomechanical analysis of the magnesiothermic reduction reactions in molten salt was investigated.Then the molten-salt-mediated magnesiothermic reduction process was studied from three different perspectives.After that,the RE-containing magnesium alloy was characterized by using chemical analysis,XRD analysis and SEM analysis.The magnesiothermic reduction was a liquid-liquid reaction with relatively weak driving force.During the melting process and the magnesiothermic reduction process,magnesium metal and the obtained alloy went up and down as a whole in molten salt,which improved the process safety without introducing chloride inclusions.Meanwhile,the hydrolysis of the RECl_(3^(-))containing molten salt occurred at elevated temperature,which severely impeded the magnesiothermic reduction process.After the magnesiothermic reduction at 750°C for 2.0 h,the content of RE and the common impurity elements in the obtained RE-containing alloy met the both requirements of the commercial WE43A and WE43B.展开更多
To satisfy the requirements for the precise formation of large-scale high-performance lightweight components with inner ring reinforcement, a new multidirectional loading rotary extrusion forming technology is develop...To satisfy the requirements for the precise formation of large-scale high-performance lightweight components with inner ring reinforcement, a new multidirectional loading rotary extrusion forming technology is developed to match the linear motion with the rotary motion and actively increases the strong shear force. Its principle is that the radial force and rotating torque increase when the blank is axially extruded and loaded. Through the synergistic action of axial, radial, and rotating motions, the orderly fow of metal is controlled, and the cumulative severe plastic deformation (SPD) of an“uplift-trowel” micro-area is generated. Consequently, materials are uniformly strengthened and toughened. Simultaneously, through the continuous deformation of a punch “ellipse-circle,” a high reinforcement component is grown on the cylinder wall to achieve the high-quality formation of cylindrical parts or the inner-ring-reinforcement components. Additionally, the efective strain increases with rotation speed, and the maximum intensity on the basal plane decreases as the number of revolutions increase. The punch structure also afects the axial extrusion loading and equivalent plastic strain. Thus, the proposed technology enriches the plastic forming theory and widens the application feld of plastic forming. Furthermore, the formed large-scale high-performance inner-ring-stifened magnesium components have been successfully verifed in aerospace equipment, thereby solving the problems of integral forming and severe deformation strengthening and toughening. The developed technology has good prospects for mass production and application.展开更多
The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shea...The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shear(CS)and compression-torsion(CT)samples are decreased,and the grain size of dynamic recrystallization(DRX)grains is also decreased.This is because that the precipitation number ofβphases is increased,and the hindering effect on grain growth can be significantly enhanced.The DRX fractions of CS and CT samples are decreased with increased strain rate.The low DRX fraction at high strain rate is related to the insufficient time for grains to nucleate.The DRX process can be promoted by the PSN mechanism of second phases,and the grain growth can be restricted by the pinning effect.At the same time,the texture strength is enhanced as the strain rate increased.Besides,the kinking degree of lamellar long-period stacking ordered(LPSO)phases is increased.Under complex shear stress conditions,non-basal slip,especially pyramidal slip,is easily activated and the texture is deflected greatly.Compared with the CS samples,CT samples have smaller average grain size,higher DRX fraction,and lower texture strength for a certain strain rate.This is because that the equivalent stress of the CT sample is larger,the stress triaxiality is smaller,so more serious dislocations are piled up near grain boundaries and second phases.At the same time,since CT sample was sheared with torsion,the dislocation movement path can be called“rotational dislocation accumulation”,and the longer distribution path of the CT sample is generated,so more sub-grains and low-angle grain boundaries(LAGBs)are formed.Compared with the CS sample,more huge-angle grain boundaries(HAGBs)and DRX grains are formed from grain boundary to grain interior,so better grain refinement effect is achieved.展开更多
Meteorological conditions have a very important impact on the development of construction projects.In order to assist project site managers to quickly and accurately deal with the engineering risks brought by meteorol...Meteorological conditions have a very important impact on the development of construction projects.In order to assist project site managers to quickly and accurately deal with the engineering risks brought by meteorological conditions,meteorological risk assessment indicators for civil construction are established based on the actual impact of different meteorological conditions on each sub-project of civil engineering.A meteorological intelligent management system is created,and it will select reasonable countermeasures from the integrated existing database and push them to on-site construction managers based on meteorological risk assessment indicators.Through the pre-set construction log module,the managers can give feedback on the application effect of the pushed measures,and achieve the effect of construction data collection,correction and expansion of the existing database.展开更多
This paper provided an efficient single pass severe plastic deformation(SPD)method,annular channel angular extrusion(ACAE),for fabricating AZ80 magnesium alloy shell part.The effect of ACAE process on the microstructu...This paper provided an efficient single pass severe plastic deformation(SPD)method,annular channel angular extrusion(ACAE),for fabricating AZ80 magnesium alloy shell part.The effect of ACAE process on the microstructure homogeneity,texture,and mechanical properties of extruded part was experimentally investigated.For comparison,conventional backward extrusion(BE)was also conducted on processing AZ80 part with same specification.The results showed that ACAE process has a better capacity to refine the microstructure and dramatic improve the deformation homogeneity of the extruded part than BE process.Due to two strong shear deformations were implemented,ACAE process could also concurrently modify the basal texture more notably than BE process.In particular,a bimodal texture was found in ACAE extruded part,which was greatly related to the enhanced synergetic action of basal slip and secondary<c+a>slip caused by the effective shear stress.More uniform and superior hardness along the thickness and height of part were achieved via ACAE process.Further surveying of tensile tests also showed that the part fabricated by ACAE process exhibited significantly higher and far more homogeneous tensile properties with an excellent balance of strength and ductility.The remarkable enhanced tensile properties of ACAE extruded part could be primarily attributed to the significant grain refinement,which provided a powerful grain boundary strengthening effect and meaningfully suppressed the development of twin-sized cracks during tensile deformation.It was established that ACAE process seemed to be a very promising single pass SPD method for manufacturing Mg-based alloy shell parts with more homogeneous microstructure and superior performance.展开更多
Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dy...Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dynamic recrystallization mechanism and texture evolution were studied.The results show that the grain size of the alloy was obviously refined after rotary backward extrusion.As the circumferenlial strain rate increased,the dynamic recrystallization fraction gradually increased causing the grain size decreased and the distribution of microstructure became more uniform.At the same time,the texture of{0001},{10-10},{11-20}was weakened and the grain orientation distribution became more random.With the increase of circumferential strain rate,the discontinuous dynamic recrystallization mechanism became dominant,which promoted the weakening of texture and grain refinement of the alloy.展开更多
In the present work,two processing routes(A and B)with 3 CEE-AEC passes are performed on Mg-13 Gd-4 Y-2 Zn-0.4 Zr alloys,and the resultant microstructure evolution,texture analysis and mechanical properties are invest...In the present work,two processing routes(A and B)with 3 CEE-AEC passes are performed on Mg-13 Gd-4 Y-2 Zn-0.4 Zr alloys,and the resultant microstructure evolution,texture analysis and mechanical properties are investigated systematically.The core difference between the two processing routes is the orientation between the expansion and extrusion steps,i.e.,they are parallel to each other for on route A and perpendicular to each other for route B.The results show that a remarkable grain refinement is achieved via both processing routes due to dynamic recrystallization(DRX).Fine equiaxed grains are observed in the samples processed with route B with a final size of 3.6±0.4μm compared to the grain size of 4.5±0.5μm with route A.With an increasing number of CEE-AEC passes,the overall texture intensity decreases,and the basal texture gradually changes to the mixed texture components.The shear deformation introduced by the asymmetrical extrusion cavity promotes a broad angular distribution of the basal planes on routes A and B,leading to an obvious increase in the Schmid factor for the activation of the basal a slip system.The tensile test at ambient temperature reveals that the comprehensive mechanical properties are improved,and the conventional mechanical anisotropy of as-received alloys is alleviated by successive CEE-AEC processing,which is mainly derived from the competitive balance relation between the grain refinement and texture modification.展开更多
Regarding the as-cast Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy,the effect of heat treatment on its properties at room temperature(RT),as well as the mechanical properties and microstructure evolution of various peak-aging sample...Regarding the as-cast Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy,the effect of heat treatment on its properties at room temperature(RT),as well as the mechanical properties and microstructure evolution of various peak-aging samples at different tensile temperatures were discussed in this article.The results indicated that the optimal heat treatment process of the alloy was:520℃×24 h+200℃×112 h.Under this condition,the yield strength(YS),ultimate tensile strength(UTS)and elongation(EL)at RT were:238 MPa,327 MPa and 2.5%,respectively.As the tensile temperature increases,the strength increases firstly and then decreases,but the ductility increases monotonously.The microstructures evolution of 200℃ peak-aging(200PA)and 250℃ peak-aging(250PA)samples were different with the increasing tensile tenperature.When tensile test processed at 150℃,the denseβ’phase and rod-shaped basalγ’phase will be formed in the 200PA sample.However,at 300℃,theβ’phases disappeared.Theβ’and LPSO phases in the 250PA sample coarsened gradually as the tensile temperature increased,and 14H-LPSO phases were formed during tensile at 300℃.The 200PA sample reached the highest strength when tensile at 150℃,which was attributed to the hindrance of the basal dislocation and non-basal dislocation slip by the prismaticβ’phases and the newly formed basalγ’precipitates.展开更多
Based on the deforming technique of severe plastic deformation(SPD), the grain refinement of a Mg-9Gd-3Y-2Zn-0.5Zr alloy treated with decreasing temperature reciprocating upsetting-extrusion(RUE) and its influence on ...Based on the deforming technique of severe plastic deformation(SPD), the grain refinement of a Mg-9Gd-3Y-2Zn-0.5Zr alloy treated with decreasing temperature reciprocating upsetting-extrusion(RUE) and its influence on the mechanical properties and wear behavior of the alloy were studied. The RUE process was carried out for 4 passes in total, starting at 0 ℃ and decreasing by 10 ℃ for each pass. The results showed that as the number of RUE passes increased, the grain refinement effect was obvious, and the second phase in the alloy was evenly distributed. Room temperature tensile properties of the alloy and the deepening of the RUE degree showed a positive correlation trend, which was due to the grain refinement, uniform distribution of the second phase and texture weakening. And the microhardness of the alloy showed that the microhardness of RUE is the largest in 2 passes. The change in microhardness was the result of dynamic competition between the softening effect of DRX and the work hardening effect. In addition, the wear resistance of the alloy showed a positive correlation with the degree of RUE under low load conditions. When the applied load was higher, the wear resistance of the alloy treated with RUE decreased compared to the initial state alloy. This phenomenon was mainly due to the presence of oxidative wear on the surface of the alloy, which could balance the positive contribution of severe plastic deformation to wear resistance to a certain extent.展开更多
High-purity anhydrous magnesium chloride was prepared from magnesia and ammonium chloride.The chlorination process was analyzed and then the critical stages affecting the purity of anhydrous magnesium chloride were pi...High-purity anhydrous magnesium chloride was prepared from magnesia and ammonium chloride.The chlorination process was analyzed and then the critical stages affecting the purity of anhydrous magnesium chloride were pinpointed.The effect of sample dimension on the above critical stages was investigated respectively.The purity guarantee mechanism of anhydrous magnesium chloride was proposed.After that,magnesium metal was obtained via electrolyzing the anhydrous magnesium chloride-containing molten salt.The new process for the continuous production of magnesium metal from magnesia was proposed and discussed.The incomplete chlorination reaction and the hydrolysis of anhydrous magnesium chloride are the two critical stages affecting the purity of the anhydrous magnesium chloride.The dimension of the sample can influence reaction process and reaction mechanism,and thus the problems of incomplete chlorination reaction and hydrolysis can be solved together.The magnesia content in anhydrous magnesium chloride was below 0.1 wt.%when the ratio of height to diameter of the sample was over 2.43.The content of impurities in the magnesium metal obtained met the specifications of the product Mg9980.The current efficiency was(94.7±1.8)%and the electricity consumption was(9107±97)kW h/t.展开更多
In this paper, the author analyzes characteristics and extracting method of interference signal of the distributed optical fiber sensing. In the distributed optical fiber sensing, realizing alarm and positioning funct...In this paper, the author analyzes characteristics and extracting method of interference signal of the distributed optical fiber sensing. In the distributed optical fiber sensing, realizing alarm and positioning function only through the cross-correlation operation will increase the load of the system, can make misinformation rate of the system be improved greatly. Therefore, before the localization algorithm, adding a interference signal feature recognition is very necessary, can reduce unnecessary operation loss and reduce the load of the system, also reducing the number of the false positives.展开更多
Numerical 2D simulation and research on internal flow field and external flow field of rocket motor nozzle using FLUENT software. Analyze the flow condition of internal flow field and external flow field, and accordin...Numerical 2D simulation and research on internal flow field and external flow field of rocket motor nozzle using FLUENT software. Analyze the flow condition of internal flow field and external flow field, and according to add in the amount of the different gas components, obtain the clear distribution of contour of density flow field, pressure flow field and various material components and so on. Simulation results agree with the results observed from the test on the ground, and provide reference for solid rocket motor development.展开更多
基金the financial supports from Program for the Supported by the Innovative Talents Support Program of Higher Education Institutions in Shanxi Provincethe‘Shanxi Province’s Key Core Technology and Common Technology Research And Development Special Project’(2020XXX015)Special Project for Scientific and Technological Cooperation and Exchange in Shanxi Province(regional cooperation project):Key Technologies for flexible manufacturing of high-strength heat-resistant magnesium alloy cabin components(202104041101033)。
文摘This paper provided an effective method to further improve the mechanical properties of the AZ80+0.4%Ce magnesium alloy wheel spoke.The effect of high strength and ductility was obtained with a yield strength of 295.36 MPa,an elongation of 10%,by the combination of pre-deformation(7%deformation)and two-stage aging treatment(120℃/9 h+175℃/24 h).The evolution of the microstructure and properties of the alloy was explored under the coupling conditions of different pre-deformation degrees and multi-stage aging.The results show that,pre-deformation introduced a large number of(1012)tensile twinning and dislocations,which greatly promoted the probability of continuous precipitates(CPs)appearing.On the contrary,the discontinuous precipitates(DPs)were limited by the vertical and horizontal twin structure.As a result,the pre-nucleation method of two-stage aging increased the proportion of CPs by 34%-38%.Owing to the DPs was effectively suppressed,the alloy's yield strength has been greatly improved.Besides,under multi-stage aging,the twin boundaries induce protruding nucleation to form static recrystallization by hindering the migration of dislocations,and the matrix swallows the twins,then the texture gradually tilts from the two poles to the basal plane.As an important supplement,the grain refinement and oblique texture promoted the improvement of the yield strength of the component.
基金supported by key technology research and development project of Shan Xi province(20201102019)Natural science foundation of Shanxi Province(201901D111167)+1 种基金Shanxi Scholarship Council of China(2020–117)JCKY2018408B003Magnesium alloy high-performance XXX multi-directional extrusion technology and XX supporting scientific research project(xxxx-2019-021)。
文摘The extruded AZ80+0.4%Ce magnesium alloy was twisted in the temperature range of 300-380℃by using a Gleeble 3500 thermal simulation test machine with a torsion unit.The deformed cylindrical specimens were cooled at a cooling rate of 10℃/s or 0.1℃/s,respectively,and aged at 170℃.The microstructure analysis results showed that the grain size decreased with increasing specimen radial position from center(SRPC),and that the strong initial basal texture of the extruded magnesium alloy was weakened.Both continuous and discontinuous dynamic recrystallization mechanisms were involved in contributing to the grain refinement for all specimens investigated.And a novel extension twinning induced dynamic recrystallization mechanism was proposed for specimen deformed at 300℃.For the specimens deformed at 300℃and 340℃followed by a slow cooling rate(0.1℃/s),precipitates of various shapes(β-Mg_(17)Al_(12)),with the dominant precipitates being on the grains boundaries,appeared on the surface section.For specimen deformed at 380℃,lamellar precipitates(LPS)in the interiors of the grains were predominant.After aging,the LPS still dominated for specimens twisted at 380℃;however,the LPS gradually decreased with decreasing deformation temperatures from 380℃to 300℃.Dynamically precipitatedβ,especially those decorating the grain boundaries,changed the competition pictures for the LPS and precipitates of other shapes after aging.Interestingly,LPS dominated the areas for the center section of the specimens after aging regardless of deformation temperatures.Low temperature deformation with high SRPC followed by rapid cooling rate increased the micro hardness of the alloy after aging due to refined grain,reduced precipitates size,decreased lamellar spacing as well as strain hardening.
基金supported by the National Key Research and Development Program of China(Grant No.2022YFB3804500)the National Natural Science Foundation of China(Grant No.52202352,22335006)+4 种基金the Shanghai Municipal Health Commission(Grant No.20224Y0010)the CAMS Innovation Fund for Medical Sciences(Grant No.2021-I2M-5-012)the Basic Research Program of Shanghai Municipal Government(Grant No.21JC1406000)the Fundamental Research Funds for the Central Universities(Grant No.22120230237,2023-3-YB-11,22120220618)the Basic Research Program of Shanghai Municipal Government(23DX1900200).
文摘The current single-atom catalysts(SACs)for medicine still suffer from the limited active site density.Here,we develop a synthetic method capable of increasing both the metal loading and mass-specific activity of SACs by exchanging zinc with iron.The constructed iron SACs(h^(3)-FNC)with a high metal loading of 6.27 wt%and an optimized adjacent Fe distance of~4 A exhibit excellent oxidase-like catalytic performance without significant activity decay after being stored for six months and promising antibacterial effects.Attractively,a“density effect”has been found at a high-enough metal doping amount,at which individual active sites become close enough to interact with each other and alter the electronic structure,resulting in significantly boosted intrinsic activity of single-atomic iron sites in h^(3)-FNCs by 2.3 times compared to low-and medium-loading SACs.Consequently,the overall catalytic activity of h^(3)-FNC is highly improved,with mass activity and metal mass-specific activity that are,respectively,66 and 315 times higher than those of commercial Pt/C.In addition,h^(3)-FNCs demonstrate efficiently enhanced capability in catalyzing oxygen reduction into superoxide anion(O_(2)·^(−))and glutathione(GSH)depletion.Both in vitro and in vivo assays demonstrate the superior antibacterial efficacy of h^(3)-FNCs in promoting wound healing.This work presents an intriguing activity-enhancement effect in catalysts and exhibits impressive therapeutic efficacy in combating bacterial infections.
基金supported by key technology research and development project of ShanXi province(20201102019)Natural science foundation of Shanxi Province(201901D111167)+2 种基金Shanxi Scholarship Council of China(2020-117)JCKY2018408B003Magnesium alloy high-performance XXX multi-directional extrusion technologyXX supporting scientific research project(xxxx-2019-021).
文摘Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The results indicated that the average grain sizes were refined forming gradient structure with increasing specimen radial position from center(12.2-5.4μm),and that the initial basal texture intensity of the extruded magnesium alloy was weakened from 46.2 to 8.3.Furthermore,the extension twins(ETs)could be disintegrated from the twins forming separated twins with smaller sizes.Interestingly,ETs with the same twin variant intersecting with each other could be coalesced forming grains with similar orientation,while ETs with different twin variants were separated by twins boundaries contributing to grain refinement.Moreover,in addition to the conventional continuous dynamic recrystallized(CDRX)grains with 30˚orientation rotated around C-axis of the parent grains,CDRXed grains with 30˚rotation around a-axis and random rotation axis were also discerned.Besides,the CDRX evolution induced twins were also elaborated,exhibiting the complex competition between CDRX and twining.Hot torsion deformation with constant decreasing temperatures rate is an effective way of grain refinement and texture modification.
基金funded in part by the National Natural Science Foundation of China under Grant No.61872038in part by the Fundamental Research Funds for the Central Universities under Grant No.FRF-GF-20-15B.
文摘Effective user authentication is key to ensuring equipment security,data privacy,and personalized services in Internet of Things(IoT)systems.However,conventional mode-based authentication methods(e.g.,passwords and smart cards)may be vulnerable to a broad range of attacks(e.g.,eavesdropping and side-channel attacks).Hence,there have been attempts to design biometric-based authentication solutions,which rely on physiological and behavioral characteristics.Behavioral characteristics need continuous monitoring and specific environmental settings,which can be challenging to implement in practice.However,we can also leverage Artificial Intelligence(AI)in the extraction and classification of physiological characteristics from IoT devices processing to facilitate authentication.Thus,we review the literature on the use of AI in physiological characteristics recognition pub-lished after 2015.We use the three-layer architecture of the IoT(i.e.,sensing layer,feature layer,and algorithm layer)to guide the discussion of existing approaches and their limitations.We also identify a number of future research opportunities,which will hopefully guide the design of next generation solutions.
基金supported by the following grants:National Natural Science Foundation of China(62125504,62361166631)STI 2030-Major Projects(2021ZD0200401)+1 种基金the Fundamental Research Funds for the Central Universities(226-2022-00201)the Open Project Program of Wuhan National Laboratory for Optoelectronics(2021WNLOKF007).
文摘Stimulated emission depletion microscopy(STED)holds great potential in biological science applications,especially in studying nanoscale subcellular structures.However,multi-color STED imaging in live-cell remains challenging due to the limited excitation wavelengths and large amount of laser radiation.Here,we develop a multiplexed live-cell STED method to observe more structures simultaneously with limited photo-bleaching and photo-cytotoxicity.By separating live-cell fluorescent probes with similar spectral properties using phasor analysis,our method enables five-color live-cell STED imaging and reveals long-term interactions between different subcellular structures.The results here provide an avenue for understanding the complex and delicate interactome of subcellular structures in live-cell.
基金The financial support from Joint Funds of the National Natural Science Foundation of China (No.U20A20230)the Natural Science Foundation of China (No.52075501)+1 种基金Young Elite Scientists Sponsorship Program by CAST (2022QNRC001)the Key R&D program of Shanxi Province (No.2020XXX015)。
文摘The lightweight of high-end equipment relies on high mechanical properties magnesium(Mg) alloy structural components, because it is the best way to improve equipment service performance and reduce energy consumption. This article summarizes the current progress and characteristics of large-scale high-performance Mg alloy components by analyzing the strengthening-toughening mechanisms, characteristics of plastic forming, and the preparation of large high mechanical properties forging blanks. Due to the lack of breakthroughs in the key technologies for forming large-scale Mg alloy components, their uniformity of mechanical properties and consistency are poor, the forming accuracy of components is low, and the production cost is high, which limit their engineering application and restrict the lightweight level of high-end equipment. In view of the above problems, the forming trends and research directions of large-scale and high mechanical properties Mg alloy components are proposed in this paper. It can provide help for the breakthrough of the key technology of large-scale Mg alloy components with high mechanical properties and expand the application of Mg alloy in high-end products.
基金supported by the National Natural Science Foundation of China(51501178)Autonomous Research Fund of State Key Laboratory of Multiphase Complex Systems(MPCS-2019-A-10)
文摘RE-containing magnesium alloys were prepared via molten-salt-mediated magnesiothermic reduction by using RE_(2)O_(3)(RE=Y,Nd and Gd)and Mg metal as raw materials.The thermomechanical analysis of the magnesiothermic reduction reactions in molten salt was investigated.Then the molten-salt-mediated magnesiothermic reduction process was studied from three different perspectives.After that,the RE-containing magnesium alloy was characterized by using chemical analysis,XRD analysis and SEM analysis.The magnesiothermic reduction was a liquid-liquid reaction with relatively weak driving force.During the melting process and the magnesiothermic reduction process,magnesium metal and the obtained alloy went up and down as a whole in molten salt,which improved the process safety without introducing chloride inclusions.Meanwhile,the hydrolysis of the RECl_(3^(-))containing molten salt occurred at elevated temperature,which severely impeded the magnesiothermic reduction process.After the magnesiothermic reduction at 750°C for 2.0 h,the content of RE and the common impurity elements in the obtained RE-containing alloy met the both requirements of the commercial WE43A and WE43B.
基金Supported by National Natural Science Foundation of China(Grant Nos.52075501,51775520)Joint Funds of National Natural Science Foundation of China(Grant No.U20A20230)Shanxi Scholarship Council of China(2021-127).
文摘To satisfy the requirements for the precise formation of large-scale high-performance lightweight components with inner ring reinforcement, a new multidirectional loading rotary extrusion forming technology is developed to match the linear motion with the rotary motion and actively increases the strong shear force. Its principle is that the radial force and rotating torque increase when the blank is axially extruded and loaded. Through the synergistic action of axial, radial, and rotating motions, the orderly fow of metal is controlled, and the cumulative severe plastic deformation (SPD) of an“uplift-trowel” micro-area is generated. Consequently, materials are uniformly strengthened and toughened. Simultaneously, through the continuous deformation of a punch “ellipse-circle,” a high reinforcement component is grown on the cylinder wall to achieve the high-quality formation of cylindrical parts or the inner-ring-reinforcement components. Additionally, the efective strain increases with rotation speed, and the maximum intensity on the basal plane decreases as the number of revolutions increase. The punch structure also afects the axial extrusion loading and equivalent plastic strain. Thus, the proposed technology enriches the plastic forming theory and widens the application feld of plastic forming. Furthermore, the formed large-scale high-performance inner-ring-stifened magnesium components have been successfully verifed in aerospace equipment, thereby solving the problems of integral forming and severe deformation strengthening and toughening. The developed technology has good prospects for mass production and application.
基金supported by Project supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U20A20230)Natural Science Foundation of Shanxi Province(No.201901D111176)+2 种基金Project supported by the Key R&D program of Shanxi Province(No.2020XXX015)Research Project Supported by Shanxi Scholarship Council of China(2021-127)Graduate Education Innovation Program of Shanxi Province(2022Y579).
文摘The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shear(CS)and compression-torsion(CT)samples are decreased,and the grain size of dynamic recrystallization(DRX)grains is also decreased.This is because that the precipitation number ofβphases is increased,and the hindering effect on grain growth can be significantly enhanced.The DRX fractions of CS and CT samples are decreased with increased strain rate.The low DRX fraction at high strain rate is related to the insufficient time for grains to nucleate.The DRX process can be promoted by the PSN mechanism of second phases,and the grain growth can be restricted by the pinning effect.At the same time,the texture strength is enhanced as the strain rate increased.Besides,the kinking degree of lamellar long-period stacking ordered(LPSO)phases is increased.Under complex shear stress conditions,non-basal slip,especially pyramidal slip,is easily activated and the texture is deflected greatly.Compared with the CS samples,CT samples have smaller average grain size,higher DRX fraction,and lower texture strength for a certain strain rate.This is because that the equivalent stress of the CT sample is larger,the stress triaxiality is smaller,so more serious dislocations are piled up near grain boundaries and second phases.At the same time,since CT sample was sheared with torsion,the dislocation movement path can be called“rotational dislocation accumulation”,and the longer distribution path of the CT sample is generated,so more sub-grains and low-angle grain boundaries(LAGBs)are formed.Compared with the CS sample,more huge-angle grain boundaries(HAGBs)and DRX grains are formed from grain boundary to grain interior,so better grain refinement effect is achieved.
基金Supported by the Scientific Research Project of Shanghai Scientific and Technological Commission(19DZ1201403)Rising-Star Program of"Science and Technology Innovation Action Plan"of Shanghai City in 2021(21QB1403200).
文摘Meteorological conditions have a very important impact on the development of construction projects.In order to assist project site managers to quickly and accurately deal with the engineering risks brought by meteorological conditions,meteorological risk assessment indicators for civil construction are established based on the actual impact of different meteorological conditions on each sub-project of civil engineering.A meteorological intelligent management system is created,and it will select reasonable countermeasures from the integrated existing database and push them to on-site construction managers based on meteorological risk assessment indicators.Through the pre-set construction log module,the managers can give feedback on the application effect of the pushed measures,and achieve the effect of construction data collection,correction and expansion of the existing database.
基金The authors gratefully acknowledge the financial supports from the National Natural Science Foundation of China(Grant no.51605448)Natural Science Foundation of Shanxi(Grant no.201701D221093)"HIGH-GRADE CNC machine tools and basic manufacturing equipment"Major National Science and technology projects(Grant no.2019ZX04022001-004).
文摘This paper provided an efficient single pass severe plastic deformation(SPD)method,annular channel angular extrusion(ACAE),for fabricating AZ80 magnesium alloy shell part.The effect of ACAE process on the microstructure homogeneity,texture,and mechanical properties of extruded part was experimentally investigated.For comparison,conventional backward extrusion(BE)was also conducted on processing AZ80 part with same specification.The results showed that ACAE process has a better capacity to refine the microstructure and dramatic improve the deformation homogeneity of the extruded part than BE process.Due to two strong shear deformations were implemented,ACAE process could also concurrently modify the basal texture more notably than BE process.In particular,a bimodal texture was found in ACAE extruded part,which was greatly related to the enhanced synergetic action of basal slip and secondary<c+a>slip caused by the effective shear stress.More uniform and superior hardness along the thickness and height of part were achieved via ACAE process.Further surveying of tensile tests also showed that the part fabricated by ACAE process exhibited significantly higher and far more homogeneous tensile properties with an excellent balance of strength and ductility.The remarkable enhanced tensile properties of ACAE extruded part could be primarily attributed to the significant grain refinement,which provided a powerful grain boundary strengthening effect and meaningfully suppressed the development of twin-sized cracks during tensile deformation.It was established that ACAE process seemed to be a very promising single pass SPD method for manufacturing Mg-based alloy shell parts with more homogeneous microstructure and superior performance.
基金the National Natural Science Foundation of China(Grant No.51775520)the National Key Research and Development Plan(Grant No.2016YFB0301103-3).
文摘Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dynamic recrystallization mechanism and texture evolution were studied.The results show that the grain size of the alloy was obviously refined after rotary backward extrusion.As the circumferenlial strain rate increased,the dynamic recrystallization fraction gradually increased causing the grain size decreased and the distribution of microstructure became more uniform.At the same time,the texture of{0001},{10-10},{11-20}was weakened and the grain orientation distribution became more random.With the increase of circumferential strain rate,the discontinuous dynamic recrystallization mechanism became dominant,which promoted the weakening of texture and grain refinement of the alloy.
基金support of the National Natural Science Foundation of China under grant No.51775520,No.52075501the Key R&D program of Shanxi Province(International Cooperation)under grant No.201903D421036+1 种基金the Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi under grant No.2018002the Natural Science Foundation of Shanxi Province under grant No.201801D121106。
文摘In the present work,two processing routes(A and B)with 3 CEE-AEC passes are performed on Mg-13 Gd-4 Y-2 Zn-0.4 Zr alloys,and the resultant microstructure evolution,texture analysis and mechanical properties are investigated systematically.The core difference between the two processing routes is the orientation between the expansion and extrusion steps,i.e.,they are parallel to each other for on route A and perpendicular to each other for route B.The results show that a remarkable grain refinement is achieved via both processing routes due to dynamic recrystallization(DRX).Fine equiaxed grains are observed in the samples processed with route B with a final size of 3.6±0.4μm compared to the grain size of 4.5±0.5μm with route A.With an increasing number of CEE-AEC passes,the overall texture intensity decreases,and the basal texture gradually changes to the mixed texture components.The shear deformation introduced by the asymmetrical extrusion cavity promotes a broad angular distribution of the basal planes on routes A and B,leading to an obvious increase in the Schmid factor for the activation of the basal a slip system.The tensile test at ambient temperature reveals that the comprehensive mechanical properties are improved,and the conventional mechanical anisotropy of as-received alloys is alleviated by successive CEE-AEC processing,which is mainly derived from the competitive balance relation between the grain refinement and texture modification.
基金supported by the National Natu-ral Science Foundation of China(Grant No.52075501).
文摘Regarding the as-cast Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy,the effect of heat treatment on its properties at room temperature(RT),as well as the mechanical properties and microstructure evolution of various peak-aging samples at different tensile temperatures were discussed in this article.The results indicated that the optimal heat treatment process of the alloy was:520℃×24 h+200℃×112 h.Under this condition,the yield strength(YS),ultimate tensile strength(UTS)and elongation(EL)at RT were:238 MPa,327 MPa and 2.5%,respectively.As the tensile temperature increases,the strength increases firstly and then decreases,but the ductility increases monotonously.The microstructures evolution of 200℃ peak-aging(200PA)and 250℃ peak-aging(250PA)samples were different with the increasing tensile tenperature.When tensile test processed at 150℃,the denseβ’phase and rod-shaped basalγ’phase will be formed in the 200PA sample.However,at 300℃,theβ’phases disappeared.Theβ’and LPSO phases in the 250PA sample coarsened gradually as the tensile temperature increased,and 14H-LPSO phases were formed during tensile at 300℃.The 200PA sample reached the highest strength when tensile at 150℃,which was attributed to the hindrance of the basal dislocation and non-basal dislocation slip by the prismaticβ’phases and the newly formed basalγ’precipitates.
基金financially supported by the Natural Science Foundation of Shanxi Province (No. 201901D111176)the Joint Funds of the National Natural Science Foundation of china (Grant No. U20A20230)+3 种基金the Bureau of science, technology and industry for National Defense of China (No. WDZC2019JJ006)the Key R&D program of Shanxi Province (International Cooperation) (No. 201903D421036)the National Natural Science Foundation of China (Grant No. 52075501)Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi (No. 2018002)。
文摘Based on the deforming technique of severe plastic deformation(SPD), the grain refinement of a Mg-9Gd-3Y-2Zn-0.5Zr alloy treated with decreasing temperature reciprocating upsetting-extrusion(RUE) and its influence on the mechanical properties and wear behavior of the alloy were studied. The RUE process was carried out for 4 passes in total, starting at 0 ℃ and decreasing by 10 ℃ for each pass. The results showed that as the number of RUE passes increased, the grain refinement effect was obvious, and the second phase in the alloy was evenly distributed. Room temperature tensile properties of the alloy and the deepening of the RUE degree showed a positive correlation trend, which was due to the grain refinement, uniform distribution of the second phase and texture weakening. And the microhardness of the alloy showed that the microhardness of RUE is the largest in 2 passes. The change in microhardness was the result of dynamic competition between the softening effect of DRX and the work hardening effect. In addition, the wear resistance of the alloy showed a positive correlation with the degree of RUE under low load conditions. When the applied load was higher, the wear resistance of the alloy treated with RUE decreased compared to the initial state alloy. This phenomenon was mainly due to the presence of oxidative wear on the surface of the alloy, which could balance the positive contribution of severe plastic deformation to wear resistance to a certain extent.
基金supported by the National Natural Science Foundation of China(51501178)Autonomous Research Fund of State Key Laboratory of Multiphase Complex Systems(MPCS-2019-A-10)。
文摘High-purity anhydrous magnesium chloride was prepared from magnesia and ammonium chloride.The chlorination process was analyzed and then the critical stages affecting the purity of anhydrous magnesium chloride were pinpointed.The effect of sample dimension on the above critical stages was investigated respectively.The purity guarantee mechanism of anhydrous magnesium chloride was proposed.After that,magnesium metal was obtained via electrolyzing the anhydrous magnesium chloride-containing molten salt.The new process for the continuous production of magnesium metal from magnesia was proposed and discussed.The incomplete chlorination reaction and the hydrolysis of anhydrous magnesium chloride are the two critical stages affecting the purity of the anhydrous magnesium chloride.The dimension of the sample can influence reaction process and reaction mechanism,and thus the problems of incomplete chlorination reaction and hydrolysis can be solved together.The magnesia content in anhydrous magnesium chloride was below 0.1 wt.%when the ratio of height to diameter of the sample was over 2.43.The content of impurities in the magnesium metal obtained met the specifications of the product Mg9980.The current efficiency was(94.7±1.8)%and the electricity consumption was(9107±97)kW h/t.
文摘In this paper, the author analyzes characteristics and extracting method of interference signal of the distributed optical fiber sensing. In the distributed optical fiber sensing, realizing alarm and positioning function only through the cross-correlation operation will increase the load of the system, can make misinformation rate of the system be improved greatly. Therefore, before the localization algorithm, adding a interference signal feature recognition is very necessary, can reduce unnecessary operation loss and reduce the load of the system, also reducing the number of the false positives.
文摘Numerical 2D simulation and research on internal flow field and external flow field of rocket motor nozzle using FLUENT software. Analyze the flow condition of internal flow field and external flow field, and according to add in the amount of the different gas components, obtain the clear distribution of contour of density flow field, pressure flow field and various material components and so on. Simulation results agree with the results observed from the test on the ground, and provide reference for solid rocket motor development.
