To understand the hot compression deformation characteristics of the self-developed Al-9.3Zn-2.4Mg^(-1).1Cu alloy,the hot compression tests of Al-9.3Zn-2.4Mg^(-1).1Cu alloy were investigated by Gleeble 1500 thermo-mec...To understand the hot compression deformation characteristics of the self-developed Al-9.3Zn-2.4Mg^(-1).1Cu alloy,the hot compression tests of Al-9.3Zn-2.4Mg^(-1).1Cu alloy were investigated by Gleeble 1500 thermo-mechanical simulator to determine the best hot processing conditions.The hot deformation temperatures were 300,350,400,and 450℃,and the strain rates were 1,0.1,0.01,and 0.003 s^(-1),respectively.Based on the experimental results,the constitutive equation and hot processing maps are established,and the corresponding strain rate and temperature-sensitive index are analyzed.The results show that Al-9.3Zn-2.4Mg^(-1).1Cu alloy has a dynamic softening trend and high strain rate sensitivity during the isothermal compression process.The hot deformation behavior can be described by an Arrhenius-type equation after strain compensation.The temperature has a negligible effect on the hot processing properties,while a low strain rate is favorable for the hot working of alloy.The processing maps and microstructure show that the optimal processing conditions were in the temperature range of 400-450℃and strain rate range of 0.003-0.005 s^(-1).展开更多
The frequency and duration of observed concurrent hot and dry events(HDEs) over China during the growing season(April–September) exhibit significant decadal changes across the mid-1990s. These changes are characteriz...The frequency and duration of observed concurrent hot and dry events(HDEs) over China during the growing season(April–September) exhibit significant decadal changes across the mid-1990s. These changes are characterized by increases in HDE frequency and duration over most of China, with relatively large increases over southeastern China(SEC), northern China(NC), and northeastern China(NEC). The frequency of HDEs averaged over China in the present day(PD,1994–2011) is double that in the early period(EP, 1964–81);the duration of HDEs increases by 60%. Climate experiments with the Met Office Unified Model(MetUM-GOML2) are used to estimate the contributions of anthropogenic forcing to HDE decadal changes over China. Anthropogenic forcing changes can explain 60%–70% of the observed decadal changes,suggesting an important anthropogenic influence on HDE changes over China across the mid-1990s. Single-forcing experiments indicate that the increase in greenhouse gas(GHG) concentrations dominates the simulated decadal changes,increasing the frequency and duration of HDEs throughout China. The change in anthropogenic aerosol(AA) emissions significantly decreases the frequency and duration of HDEs over SEC and NC, but the magnitude of the decrease is much smaller than the increase induced by GHGs. The changes in HDEs in response to anthropogenic forcing are mainly due to the response of climatological mean surface air temperatures. The contributions from changes in variability and changes in climatological mean soil moisture and evapotranspiration are relatively small. The physical processes associated with the response of HDEs to GHG and AA changes are also revealed.展开更多
Understanding the differences in mechanical properties and damage characteristics of granitoid under high temperatures is crucial for exploring deep geothermal resources.This study analyzes the evolution of the acoust...Understanding the differences in mechanical properties and damage characteristics of granitoid under high temperatures is crucial for exploring deep geothermal resources.This study analyzes the evolution of the acoustic emission(AE)characteristics and mechanical parameters of granodiorite and granite after heating and water cooling by uniaxial compression and variable-angle shear tests under different temperature gradients.We identify their changes in mesostructure and mineral composition with electron probe microanalysis and scanning electron microscopy.Results show that these two hot dry rocks have similar diagenetic minerals and microstructure,but show significantly different mechanical and acoustic characteristics,and even opposing evolution trends in a certain temperature range.At the temperatures ranging from 100℃to 500℃,the compressive and shear mechanical properties of granodiorite switch repeatedly between weakening and strengthening,and those of granite show a continuous weakening trend.At 600℃,both rocks exhibit a deterioration of mechanical properties.The damage mode of granite is characterized by initiating at low stress,exponential evolutionary activity,and intensified energy release.In contrast,granodiorite exhibits the characteristics of initiating at high stress,volatile evolutionary activity,and intermittent energy release,due to its more stable microstructure and fewer thermal defects compared to granite.As the temperature increases,the initiation and propagation of secondary cracks in granodiorite are suppressed to a certain extent,and the seismicity and brittleness are enhanced.The subtle differences in grain size,microscopic heterogeneity,and mineral composition of the two hot dry rocks determine the different acoustic-mechanical characteristics under heating and cooling,and the evolution trends with temperature.These findings are of great significance for the scientific and efficient construction of rock mass engineering by rationally utilizing different rock strata properties.展开更多
Heavy components of low-alloy high-strength(LAHS) steels are generally formed by multi-pass forging. It is necessary to explore the flow characteristics and hot workability of LAHS steels during the multi-pass forging...Heavy components of low-alloy high-strength(LAHS) steels are generally formed by multi-pass forging. It is necessary to explore the flow characteristics and hot workability of LAHS steels during the multi-pass forging process, which is beneficial to the formulation of actual processing parameters. In the study, the multi-pass hot compression experiments of a typical LAHS steel are carried out at a wide range of deformation temperatures and strain rates. It is found that the work hardening rate of the experimental material depends on deformation parameters and deformation passes, which is ascribed to the impacts of static and dynamic softening behaviors. A new model is established to describe the flow characteristics at various deformation passes. Compared to the classical Arrhenius model and modified Zerilli and Armstrong model, the newly proposed model shows higher prediction accuracy with a confidence level of 0.98565. Furthermore, the connection between power dissipation efficiency(PDE) and deformation parameters is revealed by analyzing the microstructures. The PDE cannot be utilized to reflect the efficiency of energy dissipation for microstructure evolution during the entire deformation process, but only to assess the efficiency of energy dissipation for microstructure evolution in a specific deformation parameter state.As a result, an integrated processing map is proposed to better study the hot workability of the LAHS steel, which considers the effects of instability factor(IF), PDE, and distribution and size of grains. The optimized processing parameters for the multi-pass deformation process are the deformation parameters of 1223–1318 K and 0.01–0.08 s^(-1). Complete dynamic recrystallization occurs within the optimized processing parameters with an average grain size of 18.36–42.3 μm. This study will guide the optimization of the forging process of heavy components.展开更多
Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid...Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid environments are not mastered. This article evaluates the influence of architectural and constructive modes of buildings made of CEB walls and concrete block walls, to optimize and compare their thermal comfort in the hot and dry tropical climate of Ouagadougou, Burkina Faso. Two identical pilot buildings whose envelopes are made of CEB and concrete blocks were monitored for this study. The thermal models of the pilot buildings were implemented in the SketchUp software using an extension of EnergyPlus. The models were empirically validated after calibration against measured thermal data from the buildings. The models were used to do a parametric analysis for optimization of the thermal performances by simulating plaster coatings on the exterior of walls, airtight openings and natural ventilation depending on external weather conditions. The results show that the CEB building displays 7016 hours of discomfort, equivalent to 80.1% of the time, and the concrete building displays 6948 hours of discomfort, equivalent to 79.3% of the time. The optimization by modifications reduced the discomfort to 2918 and 3125 hours respectively;i.e. equivalent to only 33.3% for the CEB building and 35.7% for the concrete building. More study should evaluate thermal optimizations in buildings in real time of usage such as residential buildings commonly used by the local middle class. The use of CEB as a construction material and passive means of improving thermal comfort is a suitable ecological and economical option to replace cementitious material.展开更多
The high temperature compression test of Be/2024Al composites with 62wt%Be was conducted at 500–575℃ and strain rate of0.003–0.1 s^(-1).The strain-compensated Arrhenius model and modified Johnson–Cook model were i...The high temperature compression test of Be/2024Al composites with 62wt%Be was conducted at 500–575℃ and strain rate of0.003–0.1 s^(-1).The strain-compensated Arrhenius model and modified Johnson–Cook model were introduced to predict the hot deformation behavior of Be/2024Al composites.The result shows that the activation energy of Be/2024Al composites was 363.364 k J·mol^(-1).Compared with composites reinforced with traditional ceramics,Be/2024Al composites can be deformed with ultra-high content of reinforcement,attributing to the deformable property of Be particles.The average relative error of the two models shows that modified Johnson–Cook model was more suitable for low temperature condition while strain-compensated Arrhenius model was more suitable for high temperature condition.The processing map was generated and a hot extrusion experiment was conducted according to the map.A comparation of the microstructure of Be/2024Al composites before and after extrusion shows that the Be particle deformed coordinately with the matrix and elongated at the extrusion direction.展开更多
The hot deformation behavior of Mn18Cr18N and Mn18Cr18N+Ce high nitrogen austenitic stainless steels at 1173-1473 K and 0.01-1 s^(-1) were investigated by thermal compression tests.The influence mechanism of Ce on the...The hot deformation behavior of Mn18Cr18N and Mn18Cr18N+Ce high nitrogen austenitic stainless steels at 1173-1473 K and 0.01-1 s^(-1) were investigated by thermal compression tests.The influence mechanism of Ce on the hot deformation behavior was analyzed by Ce-containing inclusions and segregation of Ce.The results show that after the addition of Ce,large,angular,hard,and brittle inclusions(TiN-Al_(2)O_(3),TiN,and Al_(2)O_(3)) can be modified to fine and dispersed Ce-containing inclusions(Ce-Al-O-S and TiN-Ce-Al-O-S).During the solidification,Ce-containing inclusions can be used as heterogeneous nucleation particles to refine as-cast grains.During the hot deformation,Ce-containing inclusions can pin dislocation movement and grain boundary migration,induce dynamic recrystallization(DRX)nucleation,and avoid the formation and propagation of micro cracks and gaps.In addition,during the solidification,Ce atoms enrich at the front of solid-li-quid interface,resulting in composition supercooling and refining the secondary dendrites.Similarly,during the hot deformation,Ce atoms tend to segregate at the boundaries of DRX grains,inhibiting the growth of grains.Under the synergistic effect of Ce-containing inclusions and Ce segregation,although the hot deformation resistance and hot deformation activation energy are improved,DRX is more likely to occur and the size of DRX grains is significantly refined,and the problem of hot deformation cracking can be alleviated.Finally,the microhardness of the samples was measured.The results show that compared with as-cast samples,the microhardness of hot-deformed samples increases signific-antly,and with the increase of DRX degree,the microhardness decreases continuously.In addition,Ce can affect the microhardness of Mn18Cr18N steel by affecting as-cast and hot deformation microstructures.展开更多
Hot compression tests were performed to investigate the hot deformation behavior of Fe–27.34Mn–8.63Al–1.03C lightweight steel and optimize the hot workability parameters. The temperature range was 900–1150℃ and t...Hot compression tests were performed to investigate the hot deformation behavior of Fe–27.34Mn–8.63Al–1.03C lightweight steel and optimize the hot workability parameters. The temperature range was 900–1150℃ and the strain rate range was 0.01–5 s^(-1)on a Gleeble-3800 thermal simulator machine. The results showed that the flow stress increased with decreasing deformation temperature and increasing strain rate. According to the constitutive equation, the activation energy of hot deformation was 422.88 kJ·mol^(-1). The relationship between the critical stress and peak stress of the tested steel was established, and a dynamic recrystallization kinetic model was thus obtained. Based on this model, the effects of strain rate and deformation temperature on the volume fraction of dynamically recrystallized grains were explored. The microstructural examination and processing map results revealed that the tested steel exhibited a good hot workability at deformation temperatures of 1010–1100℃ and strain rate of 0.01 s^(-1).展开更多
The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindric...The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.展开更多
Microwave heating can rapidly and uniformly raise the temperature and accelerate the reaction rate.In this paper,microwave heating was used to improve the acid leaching,and the mechanism was investigated via microscop...Microwave heating can rapidly and uniformly raise the temperature and accelerate the reaction rate.In this paper,microwave heating was used to improve the acid leaching,and the mechanism was investigated via microscopic morphology analysis and numerical simulation by COMSOL Multiphysics software.The effects of the microwave power,leaching temperature,CaF_(2) dosage,H_(2)SO_(4) concentration,and leaching time on the vanadium recovery were investigated.A vanadium recovery of 80.66%is obtained at a microwave power of 550 W,leaching temperature of 95℃,CaF_(2) dosage of 5wt%,H_(2)SO_(4) concentration of 20vol%,and leaching time of 2.5 h.Compared with conventional leaching technology,the vanadium recovery increases by 6.18%,and the leaching time shortens by 79.17%.More obvious pulverization of shale particles and delamination of mica minerals happen in the microwave-assisted leaching process.Numerical simulation results show that the temperature of vanadium shales increases with an increase in electric field(E-field).The distributions of E-field and temperature among vanadium shale particles are relatively uniform,except for the higher content at the contact position of the particles.The analysis results of scaleup experiments and leaching experiments indicate high-temperature hot spots in the process of microwave-assisted leaching,and the local high temperature destroys the mineral structure and accelerates the reaction rate.展开更多
Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. Howev...Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. However, there are few reports about the microstructure characteristics on the strengthening and toughening mechanisms of powder hot isostatic pressed(HIPed) titanium alloys. Therefore, TA15powder was prepared into alloy by HIP approach, which was used to explore the microstructure characteristics at different HIP temperatures and the corresponding tensile properties and fracture toughness. Results show that the fabricated alloy has a “basket-like structure” when the HIP temperature is below 950℃, consisting of lath clusters and surrounding small equiaxed grains belts. When the HIP temperature is higher than 950℃, the microstructure gradually transforms into the Widmanstatten structure, accompanied by a significant increase in grain size. The tensile strength and elongation are reduced from 948 MPa and 17.3% for the 910℃ specimen to 861 MPa and 10% for the 970℃ specimen.The corresponding tensile fracture mode changes from transcrystalline plastic fracture to mixed fracture including intercrystalline cleavage.The fracture toughness of the specimens increases from 82.64 MPa·m^(1/2)for the 910℃ specimen to 140.18 MPa·m^(1/2)for the 970℃ specimen.Specimens below 950℃ tend to form holes due to the prior particle boundaries(PPBs), which is not conducive to toughening. Specimens above 950℃ have high fracture toughness due to the crack deflection, crack branching, and shear plastic deformation of the Widmanstatten structure. This study provides a valid reference for the development of powder HIPed titanium alloy.展开更多
Despite the industrial significance of grain size for enhancing mechanical properties and formability,the in-depth deformation mechanisms at elevated temperature are still unclear.To investigate the functions of grain...Despite the industrial significance of grain size for enhancing mechanical properties and formability,the in-depth deformation mechanisms at elevated temperature are still unclear.To investigate the functions of grain size on hot workability and deformation mechanisms,three groups of Mg-1.2Zn-0.2Y alloy specimens with different grain sizes were hot compressed and then studied by combining constitutive model,processing map and microstructural observations.The results showed that the enhanced hot workability accompanying low deformation activation energy and small instability regime was obtained with refined grain size.During hot deformation,the decreased grain size in Mg1.2Zn-0.2Y alloy mainly improved the plastic deformation homogeneity,especially for the weakened local straining around grain boundaries.As a result,the dynamic recrystallization nucleation and texture development at lower strain level were influenced by the initial grain size.At higher strain magnitude,the growth and coarsening of dynamic recrystallized grains would further release strain localization and improve hot workability,while the texture was less impacted.Further,unlike the primary basal slip and deformation twinning in the specimen with coarse grain at low temperature,non-basal slips of dislocations were initiated with less deformation twins in the specimens with refined grain size.展开更多
Isothermal hot compression experiments were conducted on homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy to investigate hot deformation behavior at the temperature range of 673-773 K and the strain rate range of 0.001-1 s...Isothermal hot compression experiments were conducted on homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy to investigate hot deformation behavior at the temperature range of 673-773 K and the strain rate range of 0.001-1 s^(-1)by using a Gleeble-1500D thermo mechanical simulator.Metallographic characterization on samples deformed to true strain of 0.70 illustrates the occurrence of flow localization and/or microcrack at deformation conditions of 673 K/0.01 s^(-1),673 K/1 s^(-1)and 698 K/1 s^(-1),indicating that these three deformation conditions should be excluded during hot working of homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy.Based on the measured true stress-strain data,the strain-compensated Arrhenius constitutive model was constructed and then incorporated into UHARD subroutine of ABAQUS software to study hot deformation process of homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy.By comparison with measured force-displacement curves,the predicted results can describe well the rheological behavior of homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy,verifying the validity of finite element simulation of hot compression process with this complicated constitutive model.Numerical results demonstrate that the distribution of values of material parameters(α,n,Q and ln A)within deformed sample is inhomogeneous.This issue is directly correlated to the uneven distribution of equivalent plastic strain due to the friction effect.Moreover,at a given temperature the increase of strain rate would result in the decrease of equivalent plastic strain within the central region of deformed sample,which hinders the occurrence of dynamic recrystallization(DRX).展开更多
Among the bottlenecks that hinder the improvement of the production efficiency of hot stamping are high strength and difficulty in edge cutting and hole punching.Starting from the preparation of hot stamping multiphas...Among the bottlenecks that hinder the improvement of the production efficiency of hot stamping are high strength and difficulty in edge cutting and hole punching.Starting from the preparation of hot stamping multiphase microstructure materials,this paper developed a plate quenching die system with controllable surface temperature and prepared four types of hot stamping plates with different martensite volume fractions.Then,straight edge cold cutting experiments were performed to study the influence of cutting clearance and cutting force on fracture quality.The results show that the bright zone is the largest when the cutting clearance is 0.14 mm,and the cutting experience coefficient of the hot stamping sheet with each martensite volume fraction is obtained when the cutting clearance is 0.14 mm.The research results of this paper were applied to the production of hot stamping parts.展开更多
Hot dry rock(HDR)geothermal energy is a kind of widely distributed clean energy with huge reserves.However,its commercial development has been constrained by reservoir stimulation.In the early stage of HDR geothermal ...Hot dry rock(HDR)geothermal energy is a kind of widely distributed clean energy with huge reserves.However,its commercial development has been constrained by reservoir stimulation.In the early stage of HDR geothermal energy development,properly determining spatial distribution patterns of natural fractures in HDR reservoirs can effectively guide reservoir stimulation.This study analyzes the spatial distribution of natural fractures by using FracMan software based on the actual geological data and log data of well M-2 in the Matouying Uplift area,Hebei Province.The fracture parameters are counted and Monte Carlo simulation technique is introduced to optimize the parameters,which makes the natural fracture model more accurate and reliable.Furthermore,this study simulates hydraulic fracturing using the model combined with the actual in-situ stress parameters and the construction scheme.As verified by fitting the changes in simulated wellhead pressure during hydraulic fracturing with the actual wellhead pressure data detected during construction,the methods for natural fracture modeling used in this study are scientific and reasonable.The preliminary prediction results show that the displacement design scheme with a pump displacement of 2.0-3.0 m^(3)/min,4.0-5.5 m^(3)/min and 6-7 m^(3)/min in the early,middle and late stages,respectively,has good fracturing effect.The results of this study can be utilized as a reference for preparing development schemes for HDR reservoirs.展开更多
It was discovered the application of Al_(2)O_(3) nanofluid as lubricant for steel hot rolling could synchronously achieve oxidation protection of strips surface.The underlying mechanism was investigated through hot ro...It was discovered the application of Al_(2)O_(3) nanofluid as lubricant for steel hot rolling could synchronously achieve oxidation protection of strips surface.The underlying mechanism was investigated through hot rolling tests and molecular dynamics (MD) simulations.The employment of Al_(2)O_(3) nanoparticles contributed to significant enhancement in the lubrication performance of lubricant.The rolled strip exhibited the best surface topography that the roughness reached lowest with the sparsest surface defects.Besides,the oxide scale generated on steel surface was also thinner,and the ratio of Fe_(2)O_(3) among various iron oxides became lower.It was revealed the above oxidation protection effect of Al_(2)O_(3) nanofluid was attributed to the deposition of nanoparticles on metal surface during hot rolling.A protective layer in the thickness of about 193 nm was formed to prevent the direct contact between steel matrix and atmosphere,which was mainly composed of Al_(2)O_(3) and sintered organic molecules.MD simulations confirmed the diffusion of O_(2) and H_(2)O could be blocked by the Al_(2)O_(3) layer through physical absorption and penetration barrier effect.展开更多
The transport of hot electrons in inertial confinement fusion(ICF)is integrated issue due to the coupling of hydrodynamic evolution and many physical processes.A hot electron transport code is developed and coupled wi...The transport of hot electrons in inertial confinement fusion(ICF)is integrated issue due to the coupling of hydrodynamic evolution and many physical processes.A hot electron transport code is developed and coupled with the radiation hydrodynamic code MULTI1D in this study.Using the code,the slowing-down process and ablation process of the hot electron beam are simulated.The ablation pressure scaling law of hot electron beam is confirmed in our simulations.The hot electron transport is simulated in the radiation-ablated plasmas relevant to indirect-drive ICF,where the spatial profile of hot electron energy deposition is presented around the shock compressed region.It is shown that the hot electron can prominently increase the total ablation pressure in the early phase of radiation-ablated plasma.So,our study suggests that a potential-driven symmetric mechanism may occur under the irradiation of asymmetric hot electron beam.The possible degradation from the hot electron transport and preheating is also discussed.展开更多
The metastableβtitanium alloy TB8(Ti-12.76Mo-2.13Nb-2.73A1-0.16Si)was used as the original material,and the secondary processing method combining equal channel angular pressing(ECAP)and heat treatment was adopted.Wit...The metastableβtitanium alloy TB8(Ti-12.76Mo-2.13Nb-2.73A1-0.16Si)was used as the original material,and the secondary processing method combining equal channel angular pressing(ECAP)and heat treatment was adopted.With the help of optical microscope(OM),scanning electron microscope(SEM)and X-ray diffractometer(XRD),the corrosion behavior of TB8 titanium alloy after different secondary processing(800℃/850℃solid solution-520℃aging,ECAP-800℃/850℃solid solution-520℃aging,and800℃/850℃solid solution-ECAP-520℃aging)was studied.The experimental results show that the hot corrosion products of the six samples are similar,mainly Na_(2)Si_(2)O_(5),MoS_(2),TiCl_(2),Ti(SO_(4))_(2),and TiS.Due to the grains of the TB8 titanium alloy treated by 850℃solid solution-ECAP-520℃aging are obviously refined,the surface structure is the most smooth and dense,forming a continuous Al2O3protective film,and the surface defects are the least after corrosion.Its corrosion layer thickness is the lowest(102.3μm),only 36.5%-81.4%of that of other secondary processing titanium alloys.In addition,the corrosion kinetics curves of the six materials all follow parabolic laws,and the minimum corrosion weight gain of the samples after 850℃solutionECAP-520℃aging treatment is 0.7507 mg·mm^(-2),showing better hot corrosion resistance.展开更多
Producing complex fracture networks in a safe way plays a critical role in the hot dry rock (HDR) geothermal energy exploitation. However, conventional hydraulic fracturing (HF) generally produces high breakdown press...Producing complex fracture networks in a safe way plays a critical role in the hot dry rock (HDR) geothermal energy exploitation. However, conventional hydraulic fracturing (HF) generally produces high breakdown pressure and results only in single main fracture morphology. Furthermore, HF has also other problems such as the increased risk of seismic events and consuption of large amount of water. In this work, a new stimulation method based on cyclic soft stimulation (CSS) and liquid nitrogen (LN2) fracturing, known as cyclic LN2 fracturing is explored, which we believe has the potential to solve the above issues related to HF. The fracturing performances including breakdown pressure and fracture morphology on granites under true-triaxial stresses are investigated and compared with cyclic water fracturing. Cryo-scanning electron microscopy (Cryo-SEM) tests and X-ray computed tomography (CT) scanning tests were used for quantitative characterization of fracture parameters and to evaluate the cyclic LN2 fracturing performances. The results demonstrate that the cyclic LN2 fracturing results in reduced breakdown pressure, with between 21% and 67% lower pressure compared with using cyclic water fracturing. Cyclic LN2 fracturing tends to produce more complex and branched fractures, whereas cyclic water fracturing usually produces a single main fracture under a low number of cycles and pressure levels. Thermally-induced fractures mostly occur around the interfaces of different particles. This study shows the potential benefits of cyclic LN2 fracturing on HDR. It is expected to provide theoretical guidance for the cyclic LN2 fracturing application in HDR reservoirs.展开更多
基金Funded by the National Natural Science Foundation of China(No.52171138)Henan Provincial Science and Technology Research Project(No.222102230088)。
文摘To understand the hot compression deformation characteristics of the self-developed Al-9.3Zn-2.4Mg^(-1).1Cu alloy,the hot compression tests of Al-9.3Zn-2.4Mg^(-1).1Cu alloy were investigated by Gleeble 1500 thermo-mechanical simulator to determine the best hot processing conditions.The hot deformation temperatures were 300,350,400,and 450℃,and the strain rates were 1,0.1,0.01,and 0.003 s^(-1),respectively.Based on the experimental results,the constitutive equation and hot processing maps are established,and the corresponding strain rate and temperature-sensitive index are analyzed.The results show that Al-9.3Zn-2.4Mg^(-1).1Cu alloy has a dynamic softening trend and high strain rate sensitivity during the isothermal compression process.The hot deformation behavior can be described by an Arrhenius-type equation after strain compensation.The temperature has a negligible effect on the hot processing properties,while a low strain rate is favorable for the hot working of alloy.The processing maps and microstructure show that the optimal processing conditions were in the temperature range of 400-450℃and strain rate range of 0.003-0.005 s^(-1).
基金the University of Reading, funded by the UK–China Research and Innovation Partnership Fund through the Met Office Climate Science for Service Partnership (CSSP) China as part of the Newton Fundsupported by the National Natural Science Foundation of China (Grant Nos. 42030603 and 42175044)+1 种基金supported by CSSP-China. NPK was supported by an Independent Research Fellowship from the Natural Environment Research Council (Grant No. NE/L010976/1)supported by the National Centre for Atmospheric Science via the NERC/GCRF programme “Atmospheric hazards in developing countries: risk assessment and early warnings ” (ACREW)。
文摘The frequency and duration of observed concurrent hot and dry events(HDEs) over China during the growing season(April–September) exhibit significant decadal changes across the mid-1990s. These changes are characterized by increases in HDE frequency and duration over most of China, with relatively large increases over southeastern China(SEC), northern China(NC), and northeastern China(NEC). The frequency of HDEs averaged over China in the present day(PD,1994–2011) is double that in the early period(EP, 1964–81);the duration of HDEs increases by 60%. Climate experiments with the Met Office Unified Model(MetUM-GOML2) are used to estimate the contributions of anthropogenic forcing to HDE decadal changes over China. Anthropogenic forcing changes can explain 60%–70% of the observed decadal changes,suggesting an important anthropogenic influence on HDE changes over China across the mid-1990s. Single-forcing experiments indicate that the increase in greenhouse gas(GHG) concentrations dominates the simulated decadal changes,increasing the frequency and duration of HDEs throughout China. The change in anthropogenic aerosol(AA) emissions significantly decreases the frequency and duration of HDEs over SEC and NC, but the magnitude of the decrease is much smaller than the increase induced by GHGs. The changes in HDEs in response to anthropogenic forcing are mainly due to the response of climatological mean surface air temperatures. The contributions from changes in variability and changes in climatological mean soil moisture and evapotranspiration are relatively small. The physical processes associated with the response of HDEs to GHG and AA changes are also revealed.
基金The authors would like to acknowledge the financial support from the National Natural Science Foundation of China(Grant No.52104112)the Research Foundation of the Department of Natural Resources of Hunan Province,China(Grant No.20230101DZ)the Natural Science Foundation of Hunan Province,China(Grant No.2023JJ20062).
文摘Understanding the differences in mechanical properties and damage characteristics of granitoid under high temperatures is crucial for exploring deep geothermal resources.This study analyzes the evolution of the acoustic emission(AE)characteristics and mechanical parameters of granodiorite and granite after heating and water cooling by uniaxial compression and variable-angle shear tests under different temperature gradients.We identify their changes in mesostructure and mineral composition with electron probe microanalysis and scanning electron microscopy.Results show that these two hot dry rocks have similar diagenetic minerals and microstructure,but show significantly different mechanical and acoustic characteristics,and even opposing evolution trends in a certain temperature range.At the temperatures ranging from 100℃to 500℃,the compressive and shear mechanical properties of granodiorite switch repeatedly between weakening and strengthening,and those of granite show a continuous weakening trend.At 600℃,both rocks exhibit a deterioration of mechanical properties.The damage mode of granite is characterized by initiating at low stress,exponential evolutionary activity,and intensified energy release.In contrast,granodiorite exhibits the characteristics of initiating at high stress,volatile evolutionary activity,and intermittent energy release,due to its more stable microstructure and fewer thermal defects compared to granite.As the temperature increases,the initiation and propagation of secondary cracks in granodiorite are suppressed to a certain extent,and the seismicity and brittleness are enhanced.The subtle differences in grain size,microscopic heterogeneity,and mineral composition of the two hot dry rocks determine the different acoustic-mechanical characteristics under heating and cooling,and the evolution trends with temperature.These findings are of great significance for the scientific and efficient construction of rock mass engineering by rationally utilizing different rock strata properties.
基金National Natural Science Foundation of China(No.52305373)Jiangxi Provincial Natural Science Foundation(No.20232BAB214053)+2 种基金Science and Technology Major Project of Jiangxi,China(No.20194ABC28001)Fund of Jiangxi Key Laboratory of Forming and Joining Technology for Aerospace Components,Nanchang Hangkong University(No.EL202303299)PhD Starting Foundation of Nanchang Hangkong University(No,EA202303235).
文摘Heavy components of low-alloy high-strength(LAHS) steels are generally formed by multi-pass forging. It is necessary to explore the flow characteristics and hot workability of LAHS steels during the multi-pass forging process, which is beneficial to the formulation of actual processing parameters. In the study, the multi-pass hot compression experiments of a typical LAHS steel are carried out at a wide range of deformation temperatures and strain rates. It is found that the work hardening rate of the experimental material depends on deformation parameters and deformation passes, which is ascribed to the impacts of static and dynamic softening behaviors. A new model is established to describe the flow characteristics at various deformation passes. Compared to the classical Arrhenius model and modified Zerilli and Armstrong model, the newly proposed model shows higher prediction accuracy with a confidence level of 0.98565. Furthermore, the connection between power dissipation efficiency(PDE) and deformation parameters is revealed by analyzing the microstructures. The PDE cannot be utilized to reflect the efficiency of energy dissipation for microstructure evolution during the entire deformation process, but only to assess the efficiency of energy dissipation for microstructure evolution in a specific deformation parameter state.As a result, an integrated processing map is proposed to better study the hot workability of the LAHS steel, which considers the effects of instability factor(IF), PDE, and distribution and size of grains. The optimized processing parameters for the multi-pass deformation process are the deformation parameters of 1223–1318 K and 0.01–0.08 s^(-1). Complete dynamic recrystallization occurs within the optimized processing parameters with an average grain size of 18.36–42.3 μm. This study will guide the optimization of the forging process of heavy components.
文摘Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid environments are not mastered. This article evaluates the influence of architectural and constructive modes of buildings made of CEB walls and concrete block walls, to optimize and compare their thermal comfort in the hot and dry tropical climate of Ouagadougou, Burkina Faso. Two identical pilot buildings whose envelopes are made of CEB and concrete blocks were monitored for this study. The thermal models of the pilot buildings were implemented in the SketchUp software using an extension of EnergyPlus. The models were empirically validated after calibration against measured thermal data from the buildings. The models were used to do a parametric analysis for optimization of the thermal performances by simulating plaster coatings on the exterior of walls, airtight openings and natural ventilation depending on external weather conditions. The results show that the CEB building displays 7016 hours of discomfort, equivalent to 80.1% of the time, and the concrete building displays 6948 hours of discomfort, equivalent to 79.3% of the time. The optimization by modifications reduced the discomfort to 2918 and 3125 hours respectively;i.e. equivalent to only 33.3% for the CEB building and 35.7% for the concrete building. More study should evaluate thermal optimizations in buildings in real time of usage such as residential buildings commonly used by the local middle class. The use of CEB as a construction material and passive means of improving thermal comfort is a suitable ecological and economical option to replace cementitious material.
基金National Natural Science Foundation of China(Nos.52171136,51871072,51871073)the Excellent Youth Scholars project of Natural Science Foundation of Heilongjiang Province(No.YQ2021E 016)Heilongjiang Touyan Team Program。
文摘The high temperature compression test of Be/2024Al composites with 62wt%Be was conducted at 500–575℃ and strain rate of0.003–0.1 s^(-1).The strain-compensated Arrhenius model and modified Johnson–Cook model were introduced to predict the hot deformation behavior of Be/2024Al composites.The result shows that the activation energy of Be/2024Al composites was 363.364 k J·mol^(-1).Compared with composites reinforced with traditional ceramics,Be/2024Al composites can be deformed with ultra-high content of reinforcement,attributing to the deformable property of Be particles.The average relative error of the two models shows that modified Johnson–Cook model was more suitable for low temperature condition while strain-compensated Arrhenius model was more suitable for high temperature condition.The processing map was generated and a hot extrusion experiment was conducted according to the map.A comparation of the microstructure of Be/2024Al composites before and after extrusion shows that the Be particle deformed coordinately with the matrix and elongated at the extrusion direction.
基金supported by the National Natural Science Foundation of China(No.51874084)the Fundamental Research Funds for the Central Universities(No.2125026)。
文摘The hot deformation behavior of Mn18Cr18N and Mn18Cr18N+Ce high nitrogen austenitic stainless steels at 1173-1473 K and 0.01-1 s^(-1) were investigated by thermal compression tests.The influence mechanism of Ce on the hot deformation behavior was analyzed by Ce-containing inclusions and segregation of Ce.The results show that after the addition of Ce,large,angular,hard,and brittle inclusions(TiN-Al_(2)O_(3),TiN,and Al_(2)O_(3)) can be modified to fine and dispersed Ce-containing inclusions(Ce-Al-O-S and TiN-Ce-Al-O-S).During the solidification,Ce-containing inclusions can be used as heterogeneous nucleation particles to refine as-cast grains.During the hot deformation,Ce-containing inclusions can pin dislocation movement and grain boundary migration,induce dynamic recrystallization(DRX)nucleation,and avoid the formation and propagation of micro cracks and gaps.In addition,during the solidification,Ce atoms enrich at the front of solid-li-quid interface,resulting in composition supercooling and refining the secondary dendrites.Similarly,during the hot deformation,Ce atoms tend to segregate at the boundaries of DRX grains,inhibiting the growth of grains.Under the synergistic effect of Ce-containing inclusions and Ce segregation,although the hot deformation resistance and hot deformation activation energy are improved,DRX is more likely to occur and the size of DRX grains is significantly refined,and the problem of hot deformation cracking can be alleviated.Finally,the microhardness of the samples was measured.The results show that compared with as-cast samples,the microhardness of hot-deformed samples increases signific-antly,and with the increase of DRX degree,the microhardness decreases continuously.In addition,Ce can affect the microhardness of Mn18Cr18N steel by affecting as-cast and hot deformation microstructures.
基金financially supported by the National Natural Science Foundation of China (Nos. 52071300 and 51904278)the Special Funding Projects for Local Science and Technology Development guided by the Central Committee (No. YDZX20191400004587)+1 种基金the Key Research and Development Project of Zhejiang Province, China (No.2020C01131)the Innovation projects of colleges and universities in Shanxi Province, China (No. 2019L0577)。
文摘Hot compression tests were performed to investigate the hot deformation behavior of Fe–27.34Mn–8.63Al–1.03C lightweight steel and optimize the hot workability parameters. The temperature range was 900–1150℃ and the strain rate range was 0.01–5 s^(-1)on a Gleeble-3800 thermal simulator machine. The results showed that the flow stress increased with decreasing deformation temperature and increasing strain rate. According to the constitutive equation, the activation energy of hot deformation was 422.88 kJ·mol^(-1). The relationship between the critical stress and peak stress of the tested steel was established, and a dynamic recrystallization kinetic model was thus obtained. Based on this model, the effects of strain rate and deformation temperature on the volume fraction of dynamically recrystallized grains were explored. The microstructural examination and processing map results revealed that the tested steel exhibited a good hot workability at deformation temperatures of 1010–1100℃ and strain rate of 0.01 s^(-1).
基金financially supported by Guangdong Province Key Field R&D Program, China (No. 2019B01 0935001)the National Nature Science Foundation of China (No. 51905192)the Fundamental Research Funds for the Central Universities (No. FRT-TP-20-006A2)
文摘The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.
基金supported by the National Natural Science Foundation of China(No.51904211)the National Natural Science Foundation of China(No.52004187)。
文摘Microwave heating can rapidly and uniformly raise the temperature and accelerate the reaction rate.In this paper,microwave heating was used to improve the acid leaching,and the mechanism was investigated via microscopic morphology analysis and numerical simulation by COMSOL Multiphysics software.The effects of the microwave power,leaching temperature,CaF_(2) dosage,H_(2)SO_(4) concentration,and leaching time on the vanadium recovery were investigated.A vanadium recovery of 80.66%is obtained at a microwave power of 550 W,leaching temperature of 95℃,CaF_(2) dosage of 5wt%,H_(2)SO_(4) concentration of 20vol%,and leaching time of 2.5 h.Compared with conventional leaching technology,the vanadium recovery increases by 6.18%,and the leaching time shortens by 79.17%.More obvious pulverization of shale particles and delamination of mica minerals happen in the microwave-assisted leaching process.Numerical simulation results show that the temperature of vanadium shales increases with an increase in electric field(E-field).The distributions of E-field and temperature among vanadium shale particles are relatively uniform,except for the higher content at the contact position of the particles.The analysis results of scaleup experiments and leaching experiments indicate high-temperature hot spots in the process of microwave-assisted leaching,and the local high temperature destroys the mineral structure and accelerates the reaction rate.
基金financially supported by the National Natural Science Foundation of China (Nos. 51874037 and 51922004)the Beijing Natural Science Foundation (No. 2212035)+1 种基金the Fundamental Research Funds for the Central Universities (No. FRF-TP-19005C1Z)the National Defense Basic Research Project (No. JCKY2017213004)。
文摘Powder hot isostatic pressing(HIP) is an effective method to achieve near-net-shape manufacturing of high-quality complex thinwalled titanium alloy parts, and it has received extensive attention in recent years. However, there are few reports about the microstructure characteristics on the strengthening and toughening mechanisms of powder hot isostatic pressed(HIPed) titanium alloys. Therefore, TA15powder was prepared into alloy by HIP approach, which was used to explore the microstructure characteristics at different HIP temperatures and the corresponding tensile properties and fracture toughness. Results show that the fabricated alloy has a “basket-like structure” when the HIP temperature is below 950℃, consisting of lath clusters and surrounding small equiaxed grains belts. When the HIP temperature is higher than 950℃, the microstructure gradually transforms into the Widmanstatten structure, accompanied by a significant increase in grain size. The tensile strength and elongation are reduced from 948 MPa and 17.3% for the 910℃ specimen to 861 MPa and 10% for the 970℃ specimen.The corresponding tensile fracture mode changes from transcrystalline plastic fracture to mixed fracture including intercrystalline cleavage.The fracture toughness of the specimens increases from 82.64 MPa·m^(1/2)for the 910℃ specimen to 140.18 MPa·m^(1/2)for the 970℃ specimen.Specimens below 950℃ tend to form holes due to the prior particle boundaries(PPBs), which is not conducive to toughening. Specimens above 950℃ have high fracture toughness due to the crack deflection, crack branching, and shear plastic deformation of the Widmanstatten structure. This study provides a valid reference for the development of powder HIPed titanium alloy.
基金supported by the National Natural Science Foundation of China(51774124,52074114)Hunan Provincial Natural Science Foundation of China(2019JJ40017,2020JJ5062)+1 种基金Key Technologies R&D in Strategic Emerging Industries and Transformation in High-tech Achievements Program of Hunan Province(2019GK4045)Graduate Training and Innovation Practice Base of Hunan Province.
文摘Despite the industrial significance of grain size for enhancing mechanical properties and formability,the in-depth deformation mechanisms at elevated temperature are still unclear.To investigate the functions of grain size on hot workability and deformation mechanisms,three groups of Mg-1.2Zn-0.2Y alloy specimens with different grain sizes were hot compressed and then studied by combining constitutive model,processing map and microstructural observations.The results showed that the enhanced hot workability accompanying low deformation activation energy and small instability regime was obtained with refined grain size.During hot deformation,the decreased grain size in Mg1.2Zn-0.2Y alloy mainly improved the plastic deformation homogeneity,especially for the weakened local straining around grain boundaries.As a result,the dynamic recrystallization nucleation and texture development at lower strain level were influenced by the initial grain size.At higher strain magnitude,the growth and coarsening of dynamic recrystallized grains would further release strain localization and improve hot workability,while the texture was less impacted.Further,unlike the primary basal slip and deformation twinning in the specimen with coarse grain at low temperature,non-basal slips of dislocations were initiated with less deformation twins in the specimens with refined grain size.
基金supported by the National Natural Science Foundation of China(Grant Nos.51805064,51701034)the Scientific and Technological Research Program of Chongqing Municipal Education Commission(Grant Nos.KJQN201801137,KJ1600922)+1 种基金the Basic and Advanced Research Project of Chongqing Science and Technology Commission(Grant Nos.cstc2017jcyj AX0062,cstc2018jcyj AX0035)the Chongqing University Key Laboratory of Micro/Nano Materials Engineering and Technology(Grant Nos.KFJJ2003)
文摘Isothermal hot compression experiments were conducted on homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy to investigate hot deformation behavior at the temperature range of 673-773 K and the strain rate range of 0.001-1 s^(-1)by using a Gleeble-1500D thermo mechanical simulator.Metallographic characterization on samples deformed to true strain of 0.70 illustrates the occurrence of flow localization and/or microcrack at deformation conditions of 673 K/0.01 s^(-1),673 K/1 s^(-1)and 698 K/1 s^(-1),indicating that these three deformation conditions should be excluded during hot working of homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy.Based on the measured true stress-strain data,the strain-compensated Arrhenius constitutive model was constructed and then incorporated into UHARD subroutine of ABAQUS software to study hot deformation process of homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy.By comparison with measured force-displacement curves,the predicted results can describe well the rheological behavior of homogenized Mg-8.5Gd-4.5Y-0.8Zn-0.4Zr alloy,verifying the validity of finite element simulation of hot compression process with this complicated constitutive model.Numerical results demonstrate that the distribution of values of material parameters(α,n,Q and ln A)within deformed sample is inhomogeneous.This issue is directly correlated to the uneven distribution of equivalent plastic strain due to the friction effect.Moreover,at a given temperature the increase of strain rate would result in the decrease of equivalent plastic strain within the central region of deformed sample,which hinders the occurrence of dynamic recrystallization(DRX).
文摘Among the bottlenecks that hinder the improvement of the production efficiency of hot stamping are high strength and difficulty in edge cutting and hole punching.Starting from the preparation of hot stamping multiphase microstructure materials,this paper developed a plate quenching die system with controllable surface temperature and prepared four types of hot stamping plates with different martensite volume fractions.Then,straight edge cold cutting experiments were performed to study the influence of cutting clearance and cutting force on fracture quality.The results show that the bright zone is the largest when the cutting clearance is 0.14 mm,and the cutting experience coefficient of the hot stamping sheet with each martensite volume fraction is obtained when the cutting clearance is 0.14 mm.The research results of this paper were applied to the production of hot stamping parts.
文摘Hot dry rock(HDR)geothermal energy is a kind of widely distributed clean energy with huge reserves.However,its commercial development has been constrained by reservoir stimulation.In the early stage of HDR geothermal energy development,properly determining spatial distribution patterns of natural fractures in HDR reservoirs can effectively guide reservoir stimulation.This study analyzes the spatial distribution of natural fractures by using FracMan software based on the actual geological data and log data of well M-2 in the Matouying Uplift area,Hebei Province.The fracture parameters are counted and Monte Carlo simulation technique is introduced to optimize the parameters,which makes the natural fracture model more accurate and reliable.Furthermore,this study simulates hydraulic fracturing using the model combined with the actual in-situ stress parameters and the construction scheme.As verified by fitting the changes in simulated wellhead pressure during hydraulic fracturing with the actual wellhead pressure data detected during construction,the methods for natural fracture modeling used in this study are scientific and reasonable.The preliminary prediction results show that the displacement design scheme with a pump displacement of 2.0-3.0 m^(3)/min,4.0-5.5 m^(3)/min and 6-7 m^(3)/min in the early,middle and late stages,respectively,has good fracturing effect.The results of this study can be utilized as a reference for preparing development schemes for HDR reservoirs.
基金financially supported by the National Natural Science Foundation of China(No.51874036)National Key Research and Development Program of China(No.2021YFB3701305)。
文摘It was discovered the application of Al_(2)O_(3) nanofluid as lubricant for steel hot rolling could synchronously achieve oxidation protection of strips surface.The underlying mechanism was investigated through hot rolling tests and molecular dynamics (MD) simulations.The employment of Al_(2)O_(3) nanoparticles contributed to significant enhancement in the lubrication performance of lubricant.The rolled strip exhibited the best surface topography that the roughness reached lowest with the sparsest surface defects.Besides,the oxide scale generated on steel surface was also thinner,and the ratio of Fe_(2)O_(3) among various iron oxides became lower.It was revealed the above oxidation protection effect of Al_(2)O_(3) nanofluid was attributed to the deposition of nanoparticles on metal surface during hot rolling.A protective layer in the thickness of about 193 nm was formed to prevent the direct contact between steel matrix and atmosphere,which was mainly composed of Al_(2)O_(3) and sintered organic molecules.MD simulations confirmed the diffusion of O_(2) and H_(2)O could be blocked by the Al_(2)O_(3) layer through physical absorption and penetration barrier effect.
基金Project supported by the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDA25050600)the DCI joint team。
文摘The transport of hot electrons in inertial confinement fusion(ICF)is integrated issue due to the coupling of hydrodynamic evolution and many physical processes.A hot electron transport code is developed and coupled with the radiation hydrodynamic code MULTI1D in this study.Using the code,the slowing-down process and ablation process of the hot electron beam are simulated.The ablation pressure scaling law of hot electron beam is confirmed in our simulations.The hot electron transport is simulated in the radiation-ablated plasmas relevant to indirect-drive ICF,where the spatial profile of hot electron energy deposition is presented around the shock compressed region.It is shown that the hot electron can prominently increase the total ablation pressure in the early phase of radiation-ablated plasma.So,our study suggests that a potential-driven symmetric mechanism may occur under the irradiation of asymmetric hot electron beam.The possible degradation from the hot electron transport and preheating is also discussed.
基金Funded by the Key Projects of Equipment Pre-research Foundation of the Ministry of Equipment Development of the Central Military Commission of China(No.6140922010201)the Key R&D Plan of Zhenjiang(No.GY2018021)。
文摘The metastableβtitanium alloy TB8(Ti-12.76Mo-2.13Nb-2.73A1-0.16Si)was used as the original material,and the secondary processing method combining equal channel angular pressing(ECAP)and heat treatment was adopted.With the help of optical microscope(OM),scanning electron microscope(SEM)and X-ray diffractometer(XRD),the corrosion behavior of TB8 titanium alloy after different secondary processing(800℃/850℃solid solution-520℃aging,ECAP-800℃/850℃solid solution-520℃aging,and800℃/850℃solid solution-ECAP-520℃aging)was studied.The experimental results show that the hot corrosion products of the six samples are similar,mainly Na_(2)Si_(2)O_(5),MoS_(2),TiCl_(2),Ti(SO_(4))_(2),and TiS.Due to the grains of the TB8 titanium alloy treated by 850℃solid solution-ECAP-520℃aging are obviously refined,the surface structure is the most smooth and dense,forming a continuous Al2O3protective film,and the surface defects are the least after corrosion.Its corrosion layer thickness is the lowest(102.3μm),only 36.5%-81.4%of that of other secondary processing titanium alloys.In addition,the corrosion kinetics curves of the six materials all follow parabolic laws,and the minimum corrosion weight gain of the samples after 850℃solutionECAP-520℃aging treatment is 0.7507 mg·mm^(-2),showing better hot corrosion resistance.
基金supported by the Youth Program of the National Natural Science Foundation of China(52004299)Major Project of the National Natural Science Foundation of China(52192621)+2 种基金the National Science Foundation for National R&D Program for Major Research Instruments of China(51827804)Beijing Outstanding Young Scientist Program(BJJWZYJH01201911414038)the National Science Foundation for Distinguished Young Scholars of China(51725404).
文摘Producing complex fracture networks in a safe way plays a critical role in the hot dry rock (HDR) geothermal energy exploitation. However, conventional hydraulic fracturing (HF) generally produces high breakdown pressure and results only in single main fracture morphology. Furthermore, HF has also other problems such as the increased risk of seismic events and consuption of large amount of water. In this work, a new stimulation method based on cyclic soft stimulation (CSS) and liquid nitrogen (LN2) fracturing, known as cyclic LN2 fracturing is explored, which we believe has the potential to solve the above issues related to HF. The fracturing performances including breakdown pressure and fracture morphology on granites under true-triaxial stresses are investigated and compared with cyclic water fracturing. Cryo-scanning electron microscopy (Cryo-SEM) tests and X-ray computed tomography (CT) scanning tests were used for quantitative characterization of fracture parameters and to evaluate the cyclic LN2 fracturing performances. The results demonstrate that the cyclic LN2 fracturing results in reduced breakdown pressure, with between 21% and 67% lower pressure compared with using cyclic water fracturing. Cyclic LN2 fracturing tends to produce more complex and branched fractures, whereas cyclic water fracturing usually produces a single main fracture under a low number of cycles and pressure levels. Thermally-induced fractures mostly occur around the interfaces of different particles. This study shows the potential benefits of cyclic LN2 fracturing on HDR. It is expected to provide theoretical guidance for the cyclic LN2 fracturing application in HDR reservoirs.
