A series of phosphorus-modified PITQ-13 catalysts was prepared by wet impregnation of NH4H2PO4 solution into an HITQ-13 parent. The catalysts were characterized using XRD, N2 adsorption, MAS NMR and NH3-TPD. Their cat...A series of phosphorus-modified PITQ-13 catalysts was prepared by wet impregnation of NH4H2PO4 solution into an HITQ-13 parent. The catalysts were characterized using XRD, N2 adsorption, MAS NMR and NH3-TPD. Their catalytic performance in 1-butene catalytic cracking was evaluated in a fixed fluidized bed reactor. The results showed that the crystallinity, surface area and pore volume of P-modified PITQ-13 catalysts decreased with the increasing amounts of P. The number of weak acid sites increased, whereas that of strong acidity decreased. The selectivity to propylene in 1-butene cracking reactions increased because of the decrease in strong acidity. The yield of propylene achieved 41.6% over PITQ-13-2 catalyst with a P content of 1.0 wt%, which was 5.1% greater than that achieved over HITQ-13 catalyst.展开更多
Effects of space velocity, reaction temperature and support acidity on product distribution and induction period in 1-butene isomerization and metathesis over Mo/mordenite-alumina were investigated. As revealed by the...Effects of space velocity, reaction temperature and support acidity on product distribution and induction period in 1-butene isomerization and metathesis over Mo/mordenite-alumina were investigated. As revealed by the catalytic performance results, induction period and objective product were closely related to the reaction conditions. Lower space velocity led to longer induction period and higher propene yield. The optimal reaction temperature for propene production is around 150 ~C and it shifted to 100 ~C for ethene production. 1-Butene auto-metathesis predominated in the reaction network if the support with lower degree of sodium exchanged. And propene gradually became the dominant product upon increasing the support sodium exchange degree. 6Mo/H100Na0M-30A1 catalyst with a support of full sodium exchange degree exhibited the highest propene yield.展开更多
A new propene production route from 1-butene metathesis has been developed on heterogeneous 10WO3/Al2O3-HY catalysts with different HY contents. It is found that the catalysts play bi-functionally first for the isomer...A new propene production route from 1-butene metathesis has been developed on heterogeneous 10WO3/Al2O3-HY catalysts with different HY contents. It is found that the catalysts play bi-functionally first for the isomerization of 1-butene to 2-butene and then for the cross-metathesis between 1-butene and 2-butene to propene and 2-pentene. The combination of HY zeolite and Al2O3 is prerequisite for the production of propene. The propene yield keeps increasing with the HY content in the range of 10-70 wt%, where 10WO3/Al2O3-70HY exhibits the highest propene yield. The MS-H2-TPR and MS-O2-TPO characterizations indicate that the increase of HY content in the catalysts weakens the interaction between W species and supports, whereas enhance the probability of coking on the metal species and acid sites.展开更多
Adsorption properties of an adsorbent or a catalyst towards adsorbates are crucial in the process of adsorption separation or catalytic reaction. Surface morphology and structure of adsorbents have a significant impac...Adsorption properties of an adsorbent or a catalyst towards adsorbates are crucial in the process of adsorption separation or catalytic reaction. Surface morphology and structure of adsorbents have a significant impact on the adsorption properties. In this study, a novel acidic ionic liquid, 1-butyl-3-(triethoxysilylpropyl)imidazolium hydrogen sulfate(i.e., [BTPIm][HSO_4]), was synthesized and subsequently grafted onto the MCM-36 zeolite for the regulation of its adsorption properties towards isobutane and 1-butene. The resultant [BTPIm][HSO_4]-immobilized MCM-36(i.e., MCM-36-IL) was characterized by FT-IR, XPS, XRD, SEM, TG/DTG and N_2 adsorption–desorption measurement. It was found that the specific surface area, micropore volume and mesopore volume of the MCM-36 support underwent a reduction upon the immobilization of ionic liquid,while the surface density of acid increased from 0.0014 to 0.0035 mmol·m^(-2). The adsorption capacity of isobutane and 1-butene on the MCM-36-IL was determined by a static volumetric method. Results demonstrated that the interaction between isobutane and MCM-36-IL was enhanced and the interaction between 1-butene and MCM-36-IL was reduced. As a result, a tunable adsorption ratio of isobutane/1-butene on MCM-36 was achieved.With the increase in surface density of acid and the tunable adsorption ratio of isobutane and 1-butene on the functionalized MCM-36, the acidic ionic liquid-immobilized zeolites are beneficial to obtain an improved reaction yield and a prolonged catalyst life in the reactions catalyzed by solid acid.展开更多
The adsorption ratio of isobutane/1-butene on the catalyst surface is one of the most important factors for the C4 alkylation process. Regulation of isobutane/1-butene adsorption ratio on the zeolite-supported acid ca...The adsorption ratio of isobutane/1-butene on the catalyst surface is one of the most important factors for the C4 alkylation process. Regulation of isobutane/1-butene adsorption ratio on the zeolite-supported acid catalyst is a big challenge for catalyst preparation. To regulate the isobutane/1-butene adsorption ratio, four types of ionic liquid （i.e., IL） with different alkyl chain lengths and different acid group numbers were synthesized and were subsequently immobilized onto the MCM-22 zeolite. The as-synthesized IL-immobilized MCM-22 （i.e., MCM-22-IL） was characterized by FT1R, TGA, BET, XPS and XRD, and their adsorption capacities and adsorption molar ratios of isobutane to l-butene （I/O） were investigated to correlate with surface features of MCM-22-IL Results showed that the immobilization of ILs led to a decrease of specific surface area and pore volume. But the surface density of acid groups was increased and the adsorption molar ratio of isobutane/1-butene （I/O） was significantly im- proved by the immobilization of ionic liquids. The adsorption molar ratio of I/O is substantially improved from 0.75 to above 0.9 at 300 kPa upon immobilizing ILs. Although the alkyl chain length oflLs was found to have little effect on the adsorption molar ratio of I/O, the increase of acid group numbers led to a dramatic decrease in the adsorption I/O ratio. The results illustrated that immobilizing ionic liquids is an effective way to modify the textural, chemical and morphological properties of MCM-22. Accordingly, the immobilization of ionic liquids provides a novel and a feasible way to regulate the adsorption I/O ratio on an adsorbent or a solid catalyst.展开更多
Crystallization in polymer systems actually is a process that transfers the entangled melts into a semi-crystalline layered structure. Whether or not a chain disentangles may result in different crystallization mechan...Crystallization in polymer systems actually is a process that transfers the entangled melts into a semi-crystalline layered structure. Whether or not a chain disentangles may result in different crystallization mechanism. When compared to the crystal thickness (d(c)), the volume occupied by the chain in the melts i.e., the radius of gyration (R-g), plays a very important role in polymer crystallization. When d(c) less than or equal to R-g, crystallization does not necessitate a chain disentangling. The entanglements are just shifted into the amorphous regions. However, as d(c)>R-g, i.e., as the crystal thickness gets larger than the radius of gyration of the chain in the melt, it becomes necessary for a chain to disentangle. Then a change of crystallization mechanism occurs. Such change has been experimentally observed in the crystallization of poly(I-butene). A change in the crystal morphologies from spherulite to quadrangle, is seen via PLM, as crystallization temperatures increase. Even more, such a change is molecular weight dependent, and shifts to lower temperature as molecular weight decreases. There exists a jump of crystal thickness and crystallinity associated with morphological change, as seen via SAXS. A change of crystallization kinetics and crystallinity is further evidenced via dilatometry. The unique feature of P1b crystallization has been discussed based on the radius of gyration of chain in the melt (R-g), and very good agreement is obtained.展开更多
The crystallization and crystalline structure of syndiotactic-polypropylene (sPP) and syndiotactic-poly(1-butene) (sPB) blend containing 10 (Bl-10), 25 (Bl-25), 50 (Bl-50), 75 (Bl-75), and 90 (Bl-90) wt% of sPB, have ...The crystallization and crystalline structure of syndiotactic-polypropylene (sPP) and syndiotactic-poly(1-butene) (sPB) blend containing 10 (Bl-10), 25 (Bl-25), 50 (Bl-50), 75 (Bl-75), and 90 (Bl-90) wt% of sPB, have been investigated by means of differential scanning calorimetry (DSC), FT-IR, and wide-angle X-ray diffraction (WAXD) analyses. The melt-crystallization behavior of the blend samples was studied by DSC on the cooling process at constant rates. Bl-50, Bl-75, and Bl-90 showed lower crystallization temperatures than the neat sPP. sPP in Bl-75 showed the lowest crystallization rate among the blend samples. Bl-90 showed a two-phase molten state, and sPP in Bl-90 crystallized via two-stepprocess. Time evolution of FT-IR spectroscopy at room temperature detected conformational transformation of the sPP polymer chain in the blend samples of Bl-50 and Bl-75. The absorption peaks intensity in the FT-IR spectra derived from the helical conformations in the crystalline phase decreased, and the planar zigzag conformations in the amorphous and mesophase phases decreased over the crystallization time. The time evolution of the WAXD profile of Bl-90 indicated that sPP in the blend accelerated the crystallization of sPB. The crystallized Bl-10, Bl-25, and Bl-50 samples showed diffraction peaks in WAXD profiles and melting endothermic peak in DSC profiles derived from only the sPP crystal. The crystallinity and melting temperature of sPP in the crystallized Bl-10, Bl-25, and Bl-50 samples were almost independent of the sPB content. Both the crystalline structure of sPP and sPB were detected in Bl-75 and Bl-90. Bl-75 showed the lowest crystallinity and melting temperature of sPP among the blend samples.展开更多
Four monodentate P-ligands and their mixtures（six groups of double-ligand systems,four groups of triple-ligand systems and one group of tetra-ligand system）were used with Rh（acac）（CO）2（acac=acetylacetonate）or...Four monodentate P-ligands and their mixtures（six groups of double-ligand systems,four groups of triple-ligand systems and one group of tetra-ligand system）were used with Rh（acac）（CO）2（acac=acetylacetonate）or Rh（acac）CO（PPh3）as the catalyst in the hydroformylation reaction of 1-butene.It was found that different Rh catalysts showed little difference in the catalysis performance.The general order of catalysis performance is doubleligand system 〉 single-ligand system〉triple-ligand system 〉 tetra-ligand system.Some synergistic effect in the double-ligand system was detected which needs a further investigation.展开更多
The macromolecular architecture is the crucial factor in determining the arrangement of the ordering structures,which,because of the multiscale feature,may exhibit distinct melting behaviors and induce the so-called m...The macromolecular architecture is the crucial factor in determining the arrangement of the ordering structures,which,because of the multiscale feature,may exhibit distinct melting behaviors and induce the so-called memory effect to affect the following recrystallization.Until present,the correlation between the occurrence of memory effect and the intrinsic molecular structure is still far from the comprehensive understanding.In this work,four kinds of 1-butene/α-olefin random copolymers were designed and synthesized using the(pyridyl-amino)hafnium catalyst to introduce the different branches.The branch length was precisely controlled by the specific α-olefin comonomers,which include 1-hexene,1-decene,1-tetradecene,and 1-octadecene,while the branch density was tuned by the incorporation.As expected,the incorporation of α-olefin co-units to poly(1-butene)backbone decreases the non-isothermal crystallization kinetics and the degree of crystallinity.More interestingly,the resulting linear branch can induce the occurrence of memory effect and the threshold concentration of co-units(i.e.,branch density)decreases with increasing the branch length.Based on the results of these 1-butene/α-olefin copolymers with designable branches,a direct correlation with the occurrence of memory effect and the fraction of amorphous region was established,which quantitatively indicates the degree of local segregation of the crystallized poly(1-butene)sequences by theα-olefin co-units.展开更多
A series of nickel（II） complexes have been synthesized and characterized. Molecular structure analysis exhibits that a square planar geometry around nickel is adopted. Upon activation with MAO, these nickel（II） co...A series of nickel（II） complexes have been synthesized and characterized. Molecular structure analysis exhibits that a square planar geometry around nickel is adopted. Upon activation with MAO, these nickel（II） complexes are efficient in catalyzing the ethylene dimerization, providing 1-butene with an activity of up to 1.4 ×10^7 g/（molohoatm）. The heteroatoms of the sidearm in the complexes were proved to have great impact on the activity and selectivity of 1-butene.展开更多
Stereospecific polymerization of polar olefins has always been an attractive but challenging project because the Lewis basic polar groups of monomers are usually poisonous to the Lewis acidic metal centers of the cata...Stereospecific polymerization of polar olefins has always been an attractive but challenging project because the Lewis basic polar groups of monomers are usually poisonous to the Lewis acidic metal centers of the catalysts. In this contribution,thiophene-fused cyclopentadienyl scandium complexes 1-3 were successfully synthesized. Combined with alkylaluminium and organoborate, these complexes showed extremely low activity and no selectivity for 1-hexene polymerization. Surprisingly,highly stereo-selective coordination polymerization of unprotected polar 4-methylthio-1-butene has been achieved in high activity for the first time under the same polymerization conditions. High-molecular-weight(M_n=110×10~3) and perfectly syndiotactic(rrrr>99%) poly(4-methylthio-1-butene)(P(MTB)) was afforded. Thus the methylthio-group-assisted mechanism that the unmasked methylthio group promoted the polymerization through σ-π chelation to the active scandium center together with the vinyl group was proposed. Moreover, the methylsulfonyl functionalized syndiotactic poly(1-butene) was also easily prepared by the oxidation of P(MTB). These results provided a new route for the synthesis of functionalized stereo-regular polyolefins.展开更多
With TiCl4/MgCl2(Ti)and Al(i-Bu)3(Al)as catalysts,the thermoplastic copolymer of 1-butene(Bt)and 1-hexene(He)was synthesized successfully.The effects of Bt/He,Ti/(He+Bt),Al/Ti,temperature and reaction time on conversi...With TiCl4/MgCl2(Ti)and Al(i-Bu)3(Al)as catalysts,the thermoplastic copolymer of 1-butene(Bt)and 1-hexene(He)was synthesized successfully.The effects of Bt/He,Ti/(He+Bt),Al/Ti,temperature and reaction time on conversion,catalyst efficiency(CE),intrinsic viscosity([g])and insoluble content were studied.The copolymer was analyzed with Fourier transform-infrared(FTIR)and nuclear magnetic resonance(1H-NMR).Results showed that the optimal polymerization conditions were:He/Bt=0.25,temperature 40℃–50℃,Al/Ti=400–500,Ti/(Bt+He)=3x10-5-4x10-5,time 4 h.Intrinsic viscosity was found to increase with increasing Ti/(Bt+He)and decreasing Al/Ti and polymerization temperature.When the molar content of He,Al/Ti and polymerization temperature increased,the insoluble content in CH2Cl2 of copolymers decreased.When Ti/(Bt+He)and reaction time increased,the insoluble con-tent in CH2Cl2 of copolymers also increased.The crystal-lization and stereoregularity of poly(1-butene)decreased with the addition of He.展开更多
The Al2O3-supported PtAg catalysts were prepared and evaluated for the dehydrogenation of n-butane at 550°C in the presence of H2. The PtAg/Al2O3 catalyst prepared by an impregnation method using the Cl- removing...The Al2O3-supported PtAg catalysts were prepared and evaluated for the dehydrogenation of n-butane at 550°C in the presence of H2. The PtAg/Al2O3 catalyst prepared by an impregnation method using the Cl- removing Pt/Al2O3 and AgNO3 showed a higher activity and selectivity to butenes and 1,3-butadiene compared to the Pt/Al2O3 catalyst, but a large amount of coke (about 30 wt% versus the catalyst weight) was formed during the dehydrogenation. The free Ag metal on the prepared catalyst dramatically promoted the coke formation, because the dehydrogenation of 1-butene over the Ag/Al2O3 catalyst produced a large amount of coke. The Cl- addition to the Cl- free Pt/Al2O3 catalyst decreased the coke formation by the reaction of the free Ag particles and Cl to form AgCl which was inactive for the coke formation. The highest initial conversion (50.3%) was obtained with the selectivity to butenes and 1,3-butadiene (butenes = 80.2% and 1,3-butadiene = 5.9%) when the PtAg/Al2O3 catalyst modified with Cl- was used.展开更多
The present work contributed to a new developed production method for enhancing the quality of isoamylene （IA） by adding a small amount of tertiary amyl alcohol （TAA） to the catalyst of strong acid cation exchange...The present work contributed to a new developed production method for enhancing the quality of isoamylene （IA） by adding a small amount of tertiary amyl alcohol （TAA） to the catalyst of strong acid cation exchange resin. TAA improved the selectivity of 2-methyl-2-butene （2M2B） at a high conversion level for the isomerization of IA. Compared with the other results from the current IA units, the conversion of 2-methyl- 1-butene （2M1B）, the mass ratio of 2M2B to 2M1B and the selectivity of 2M2B were increased from 0.5474, 7.32 and 0.6864 to 0.72, 12 and 0.95, respectively, while the dimers content in the products decreased from 4.38% to below 1.0%. Optimized conditions for IA isomerization consisted of temperature between 28 and 33℃ and system pressure of 0.5 MPa, weight hourly space velocity of 8.0 h-1 with TAA mass fraction of 0.7%-0.9% in raw material. The results in lab supported bases for the developed process in industrial application which was later proved to be successful. In addition, a possible mechanism of the isomerization process was speculated to propose a key step of water formation in the TAA-added isomerization process and a verified experiment was conducted to support this speculation.展开更多
基金supported by PetroChina Company Limited(12-09-01-01)the National Basic Research Program of China(973 Program,2012CB215001)
文摘A series of phosphorus-modified PITQ-13 catalysts was prepared by wet impregnation of NH4H2PO4 solution into an HITQ-13 parent. The catalysts were characterized using XRD, N2 adsorption, MAS NMR and NH3-TPD. Their catalytic performance in 1-butene catalytic cracking was evaluated in a fixed fluidized bed reactor. The results showed that the crystallinity, surface area and pore volume of P-modified PITQ-13 catalysts decreased with the increasing amounts of P. The number of weak acid sites increased, whereas that of strong acidity decreased. The selectivity to propylene in 1-butene cracking reactions increased because of the decrease in strong acidity. The yield of propylene achieved 41.6% over PITQ-13-2 catalyst with a P content of 1.0 wt%, which was 5.1% greater than that achieved over HITQ-13 catalyst.
基金the National Natural Science Foundation of China(Grant No.20903088 and 21006104)
文摘Effects of space velocity, reaction temperature and support acidity on product distribution and induction period in 1-butene isomerization and metathesis over Mo/mordenite-alumina were investigated. As revealed by the catalytic performance results, induction period and objective product were closely related to the reaction conditions. Lower space velocity led to longer induction period and higher propene yield. The optimal reaction temperature for propene production is around 150 ~C and it shifted to 100 ~C for ethene production. 1-Butene auto-metathesis predominated in the reaction network if the support with lower degree of sodium exchanged. And propene gradually became the dominant product upon increasing the support sodium exchange degree. 6Mo/H100Na0M-30A1 catalyst with a support of full sodium exchange degree exhibited the highest propene yield.
基金supported by the National Natural Science Foundation of China (No.20773120)National 973 Project of China (No.2005CB221403)
文摘A new propene production route from 1-butene metathesis has been developed on heterogeneous 10WO3/Al2O3-HY catalysts with different HY contents. It is found that the catalysts play bi-functionally first for the isomerization of 1-butene to 2-butene and then for the cross-metathesis between 1-butene and 2-butene to propene and 2-pentene. The combination of HY zeolite and Al2O3 is prerequisite for the production of propene. The propene yield keeps increasing with the HY content in the range of 10-70 wt%, where 10WO3/Al2O3-70HY exhibits the highest propene yield. The MS-H2-TPR and MS-O2-TPO characterizations indicate that the increase of HY content in the catalysts weakens the interaction between W species and supports, whereas enhance the probability of coking on the metal species and acid sites.
基金Supported by the National Natural Science Foundation of China(No.21276163,and No.21576168)
文摘Adsorption properties of an adsorbent or a catalyst towards adsorbates are crucial in the process of adsorption separation or catalytic reaction. Surface morphology and structure of adsorbents have a significant impact on the adsorption properties. In this study, a novel acidic ionic liquid, 1-butyl-3-(triethoxysilylpropyl)imidazolium hydrogen sulfate(i.e., [BTPIm][HSO_4]), was synthesized and subsequently grafted onto the MCM-36 zeolite for the regulation of its adsorption properties towards isobutane and 1-butene. The resultant [BTPIm][HSO_4]-immobilized MCM-36(i.e., MCM-36-IL) was characterized by FT-IR, XPS, XRD, SEM, TG/DTG and N_2 adsorption–desorption measurement. It was found that the specific surface area, micropore volume and mesopore volume of the MCM-36 support underwent a reduction upon the immobilization of ionic liquid,while the surface density of acid increased from 0.0014 to 0.0035 mmol·m^(-2). The adsorption capacity of isobutane and 1-butene on the MCM-36-IL was determined by a static volumetric method. Results demonstrated that the interaction between isobutane and MCM-36-IL was enhanced and the interaction between 1-butene and MCM-36-IL was reduced. As a result, a tunable adsorption ratio of isobutane/1-butene on MCM-36 was achieved.With the increase in surface density of acid and the tunable adsorption ratio of isobutane and 1-butene on the functionalized MCM-36, the acidic ionic liquid-immobilized zeolites are beneficial to obtain an improved reaction yield and a prolonged catalyst life in the reactions catalyzed by solid acid.
基金Supported by the National Natural Science Foundation of China(21576168,21276163)
文摘The adsorption ratio of isobutane/1-butene on the catalyst surface is one of the most important factors for the C4 alkylation process. Regulation of isobutane/1-butene adsorption ratio on the zeolite-supported acid catalyst is a big challenge for catalyst preparation. To regulate the isobutane/1-butene adsorption ratio, four types of ionic liquid （i.e., IL） with different alkyl chain lengths and different acid group numbers were synthesized and were subsequently immobilized onto the MCM-22 zeolite. The as-synthesized IL-immobilized MCM-22 （i.e., MCM-22-IL） was characterized by FT1R, TGA, BET, XPS and XRD, and their adsorption capacities and adsorption molar ratios of isobutane to l-butene （I/O） were investigated to correlate with surface features of MCM-22-IL Results showed that the immobilization of ILs led to a decrease of specific surface area and pore volume. But the surface density of acid groups was increased and the adsorption molar ratio of isobutane/1-butene （I/O） was significantly im- proved by the immobilization of ionic liquids. The adsorption molar ratio of I/O is substantially improved from 0.75 to above 0.9 at 300 kPa upon immobilizing ILs. Although the alkyl chain length oflLs was found to have little effect on the adsorption molar ratio of I/O, the increase of acid group numbers led to a dramatic decrease in the adsorption I/O ratio. The results illustrated that immobilizing ionic liquids is an effective way to modify the textural, chemical and morphological properties of MCM-22. Accordingly, the immobilization of ionic liquids provides a novel and a feasible way to regulate the adsorption I/O ratio on an adsorbent or a solid catalyst.
基金This work was supported by the Deutsche Forschungsgemeinschall and der Chemischen Industrierate, Alexander von Humboldt Stiffeng and the China National Distinguished Young Investigator Fund (No. 29925413).
文摘Crystallization in polymer systems actually is a process that transfers the entangled melts into a semi-crystalline layered structure. Whether or not a chain disentangles may result in different crystallization mechanism. When compared to the crystal thickness (d(c)), the volume occupied by the chain in the melts i.e., the radius of gyration (R-g), plays a very important role in polymer crystallization. When d(c) less than or equal to R-g, crystallization does not necessitate a chain disentangling. The entanglements are just shifted into the amorphous regions. However, as d(c)>R-g, i.e., as the crystal thickness gets larger than the radius of gyration of the chain in the melt, it becomes necessary for a chain to disentangle. Then a change of crystallization mechanism occurs. Such change has been experimentally observed in the crystallization of poly(I-butene). A change in the crystal morphologies from spherulite to quadrangle, is seen via PLM, as crystallization temperatures increase. Even more, such a change is molecular weight dependent, and shifts to lower temperature as molecular weight decreases. There exists a jump of crystal thickness and crystallinity associated with morphological change, as seen via SAXS. A change of crystallization kinetics and crystallinity is further evidenced via dilatometry. The unique feature of P1b crystallization has been discussed based on the radius of gyration of chain in the melt (R-g), and very good agreement is obtained.
文摘The crystallization and crystalline structure of syndiotactic-polypropylene (sPP) and syndiotactic-poly(1-butene) (sPB) blend containing 10 (Bl-10), 25 (Bl-25), 50 (Bl-50), 75 (Bl-75), and 90 (Bl-90) wt% of sPB, have been investigated by means of differential scanning calorimetry (DSC), FT-IR, and wide-angle X-ray diffraction (WAXD) analyses. The melt-crystallization behavior of the blend samples was studied by DSC on the cooling process at constant rates. Bl-50, Bl-75, and Bl-90 showed lower crystallization temperatures than the neat sPP. sPP in Bl-75 showed the lowest crystallization rate among the blend samples. Bl-90 showed a two-phase molten state, and sPP in Bl-90 crystallized via two-stepprocess. Time evolution of FT-IR spectroscopy at room temperature detected conformational transformation of the sPP polymer chain in the blend samples of Bl-50 and Bl-75. The absorption peaks intensity in the FT-IR spectra derived from the helical conformations in the crystalline phase decreased, and the planar zigzag conformations in the amorphous and mesophase phases decreased over the crystallization time. The time evolution of the WAXD profile of Bl-90 indicated that sPP in the blend accelerated the crystallization of sPB. The crystallized Bl-10, Bl-25, and Bl-50 samples showed diffraction peaks in WAXD profiles and melting endothermic peak in DSC profiles derived from only the sPP crystal. The crystallinity and melting temperature of sPP in the crystallized Bl-10, Bl-25, and Bl-50 samples were almost independent of the sPB content. Both the crystalline structure of sPP and sPB were detected in Bl-75 and Bl-90. Bl-75 showed the lowest crystallinity and melting temperature of sPP among the blend samples.
基金Supported by the National Natural Science Foundation of China(21306227)the Science Foundation of China University of Petroleum,Beijing(C201604)
文摘Four monodentate P-ligands and their mixtures（six groups of double-ligand systems,four groups of triple-ligand systems and one group of tetra-ligand system）were used with Rh（acac）（CO）2（acac=acetylacetonate）or Rh（acac）CO（PPh3）as the catalyst in the hydroformylation reaction of 1-butene.It was found that different Rh catalysts showed little difference in the catalysis performance.The general order of catalysis performance is doubleligand system 〉 single-ligand system〉triple-ligand system 〉 tetra-ligand system.Some synergistic effect in the double-ligand system was detected which needs a further investigation.
基金financially supported by the National Natural Science Foundation of China(No.52022065)the National Key Research and Development Program of China(No.2018YFB0704200).
文摘The macromolecular architecture is the crucial factor in determining the arrangement of the ordering structures,which,because of the multiscale feature,may exhibit distinct melting behaviors and induce the so-called memory effect to affect the following recrystallization.Until present,the correlation between the occurrence of memory effect and the intrinsic molecular structure is still far from the comprehensive understanding.In this work,four kinds of 1-butene/α-olefin random copolymers were designed and synthesized using the(pyridyl-amino)hafnium catalyst to introduce the different branches.The branch length was precisely controlled by the specific α-olefin comonomers,which include 1-hexene,1-decene,1-tetradecene,and 1-octadecene,while the branch density was tuned by the incorporation.As expected,the incorporation of α-olefin co-units to poly(1-butene)backbone decreases the non-isothermal crystallization kinetics and the degree of crystallinity.More interestingly,the resulting linear branch can induce the occurrence of memory effect and the threshold concentration of co-units(i.e.,branch density)decreases with increasing the branch length.Based on the results of these 1-butene/α-olefin copolymers with designable branches,a direct correlation with the occurrence of memory effect and the fraction of amorphous region was established,which quantitatively indicates the degree of local segregation of the crystallized poly(1-butene)sequences by theα-olefin co-units.
文摘A series of nickel（II） complexes have been synthesized and characterized. Molecular structure analysis exhibits that a square planar geometry around nickel is adopted. Upon activation with MAO, these nickel（II） complexes are efficient in catalyzing the ethylene dimerization, providing 1-butene with an activity of up to 1.4 ×10^7 g/（molohoatm）. The heteroatoms of the sidearm in the complexes were proved to have great impact on the activity and selectivity of 1-butene.
基金supported by the National Natural Science Foundation of China (21674108, 21634007, 21774118)the Science and Technology Development Project of Jilin Province (20190201067JC)
文摘Stereospecific polymerization of polar olefins has always been an attractive but challenging project because the Lewis basic polar groups of monomers are usually poisonous to the Lewis acidic metal centers of the catalysts. In this contribution,thiophene-fused cyclopentadienyl scandium complexes 1-3 were successfully synthesized. Combined with alkylaluminium and organoborate, these complexes showed extremely low activity and no selectivity for 1-hexene polymerization. Surprisingly,highly stereo-selective coordination polymerization of unprotected polar 4-methylthio-1-butene has been achieved in high activity for the first time under the same polymerization conditions. High-molecular-weight(M_n=110×10~3) and perfectly syndiotactic(rrrr>99%) poly(4-methylthio-1-butene)(P(MTB)) was afforded. Thus the methylthio-group-assisted mechanism that the unmasked methylthio group promoted the polymerization through σ-π chelation to the active scandium center together with the vinyl group was proposed. Moreover, the methylsulfonyl functionalized syndiotactic poly(1-butene) was also easily prepared by the oxidation of P(MTB). These results provided a new route for the synthesis of functionalized stereo-regular polyolefins.
基金supported by the National High-Tech Research and Development Program of China(863 Program)(Grant No.2006AA03Z546).
文摘With TiCl4/MgCl2(Ti)and Al(i-Bu)3(Al)as catalysts,the thermoplastic copolymer of 1-butene(Bt)and 1-hexene(He)was synthesized successfully.The effects of Bt/He,Ti/(He+Bt),Al/Ti,temperature and reaction time on conversion,catalyst efficiency(CE),intrinsic viscosity([g])and insoluble content were studied.The copolymer was analyzed with Fourier transform-infrared(FTIR)and nuclear magnetic resonance(1H-NMR).Results showed that the optimal polymerization conditions were:He/Bt=0.25,temperature 40℃–50℃,Al/Ti=400–500,Ti/(Bt+He)=3x10-5-4x10-5,time 4 h.Intrinsic viscosity was found to increase with increasing Ti/(Bt+He)and decreasing Al/Ti and polymerization temperature.When the molar content of He,Al/Ti and polymerization temperature increased,the insoluble content in CH2Cl2 of copolymers decreased.When Ti/(Bt+He)and reaction time increased,the insoluble con-tent in CH2Cl2 of copolymers also increased.The crystal-lization and stereoregularity of poly(1-butene)decreased with the addition of He.
文摘The Al2O3-supported PtAg catalysts were prepared and evaluated for the dehydrogenation of n-butane at 550°C in the presence of H2. The PtAg/Al2O3 catalyst prepared by an impregnation method using the Cl- removing Pt/Al2O3 and AgNO3 showed a higher activity and selectivity to butenes and 1,3-butadiene compared to the Pt/Al2O3 catalyst, but a large amount of coke (about 30 wt% versus the catalyst weight) was formed during the dehydrogenation. The free Ag metal on the prepared catalyst dramatically promoted the coke formation, because the dehydrogenation of 1-butene over the Ag/Al2O3 catalyst produced a large amount of coke. The Cl- addition to the Cl- free Pt/Al2O3 catalyst decreased the coke formation by the reaction of the free Ag particles and Cl to form AgCl which was inactive for the coke formation. The highest initial conversion (50.3%) was obtained with the selectivity to butenes and 1,3-butadiene (butenes = 80.2% and 1,3-butadiene = 5.9%) when the PtAg/Al2O3 catalyst modified with Cl- was used.
文摘The present work contributed to a new developed production method for enhancing the quality of isoamylene （IA） by adding a small amount of tertiary amyl alcohol （TAA） to the catalyst of strong acid cation exchange resin. TAA improved the selectivity of 2-methyl-2-butene （2M2B） at a high conversion level for the isomerization of IA. Compared with the other results from the current IA units, the conversion of 2-methyl- 1-butene （2M1B）, the mass ratio of 2M2B to 2M1B and the selectivity of 2M2B were increased from 0.5474, 7.32 and 0.6864 to 0.72, 12 and 0.95, respectively, while the dimers content in the products decreased from 4.38% to below 1.0%. Optimized conditions for IA isomerization consisted of temperature between 28 and 33℃ and system pressure of 0.5 MPa, weight hourly space velocity of 8.0 h-1 with TAA mass fraction of 0.7%-0.9% in raw material. The results in lab supported bases for the developed process in industrial application which was later proved to be successful. In addition, a possible mechanism of the isomerization process was speculated to propose a key step of water formation in the TAA-added isomerization process and a verified experiment was conducted to support this speculation.
