Generalized stacking-fault energies （GSFEs） of basal-plane stacking faults 11 and 12 in Mg alloys have been studied based on first-principles calculations, where 43 alloying elements were considered. It is found tha...Generalized stacking-fault energies （GSFEs） of basal-plane stacking faults 11 and 12 in Mg alloys have been studied based on first-principles calculations, where 43 alloying elements were considered. It is found that the most contributing features of alloying elements to GSFEs are bulk modulus, equilibrium volume, binding energy, atomic radius and ionization energy. Both bulk modulus and ionization energy exhibit positive relationships with GSFEs, and the others show opposite relationships. Multiple regressions have been performed to offer a quantitative prediction for basal-plane GSFEs in Mg-X systems. GSFEs, alloying effects of elements and the prediction model established within this work may provide guidelines for new Mg alloys design with better ductility.展开更多
The effects of ternary solutes Ti, Co, V, Cr, Ta, W and Mo on the D03 phase 5tability of Fe3Alintermetallics are investigated by tight-binding linear Muffin-tin orbitaI method. The predictedsite preference5 of these e...The effects of ternary solutes Ti, Co, V, Cr, Ta, W and Mo on the D03 phase 5tability of Fe3Alintermetallics are investigated by tight-binding linear Muffin-tin orbitaI method. The predictedsite preference5 of these elements in Fe3AI are in agreement with the experimental observations.The calculated Iocal magnetic moment of Fe3AI is identical to the experimentaI. ln addition, itis found that the D03 phase stability of Fe3AI doped with Ti, V, Co and Cr depends on 'energygap- of energy band near Fermi level. while the D03 phase stability of Fe3AI doped with Ta, Wand Mo may be affected by Madelung energy.展开更多
The Mo 5Si 3 base alloys with a series of transition metal elements were prepared by arc melting, and were annealed at 1?250?℃ in vacuum for 24?h. Ternary alloying effect was investigated by X ray diffractometry (XRD...The Mo 5Si 3 base alloys with a series of transition metal elements were prepared by arc melting, and were annealed at 1?250?℃ in vacuum for 24?h. Ternary alloying effect was investigated by X ray diffractometry (XRD), optical microscopy, scanning electron microscopy (SEM) and energy dispersive spectroscopy(EDS). The EDS results show that Zr, Ti, Co and V have certain solubility in homogenized Mo 5Si 3, which are determined to be 2.20±1.42, 15.94±0.18, 3.33±0.76 and 7.43±0.22 (mole fraction, %), respectively. Microstructural characteristics indicate that all studied alloys have a two phase microstructure, i.e., Mo 5Si 3 matrix and the second phase Mo 37 Zr 20 Si 43 , Mo 66 Si 19 Ti 15 , MoCoSi or (Mo, V) 3Si.展开更多
The alloying effect of cerium in low carbon granular bainitic steel has been studied. Cerium increases the incubation time of granular bainitic transformation, exerts an influence on the morphology of nucleation and g...The alloying effect of cerium in low carbon granular bainitic steel has been studied. Cerium increases the incubation time of granular bainitic transformation, exerts an influence on the morphology of nucleation and growth of bainitic transformation, and refines the structure of normalized granular bainite.展开更多
The application of segmental semi-solid thixoforming of magnesium alloys is confined due to the dimensional distinction existing in solid particles of the alloy billet from edge to center zones. In the present study, ...The application of segmental semi-solid thixoforming of magnesium alloys is confined due to the dimensional distinction existing in solid particles of the alloy billet from edge to center zones. In the present study, the effects of Sm addition on the microstructural evolution of Mg-6Zn-0.4Zr and Mg-6Zn-4Sm-0.4Zr alloys by semi-solid isothermal heat treatment were investigated, to obtain optimum semi-solid microstructures for the subsequently thixoforming. The results indicate that the grains of the Sm-bearing alloy are evidently refined and gradually evolve from dendritic to globular and elliptic particles. In addition, the distinctly dimensional effect of the Mg-6Zn-0.4Zr alloy is eliminated with 4% Sm addition; the particle sizes in all zones from center to the edge of the billet are almost identical. With the increment of isothermal heat treatment temperature, the dendritic microstructures completely disappear, and meanwhile, the irregular and globular particles gradually form. The size, morphology and the distribution of solid particles mainly depend on the formation and permeation of the liquid phase in the process of isothermal heat treatment. As the isothermal temperature increases from 570 °C to 610 °C, the average size and shape factor of solid particles of both the alloys with and without Sm addition gradually decrease while the liquid fraction gradually increases.展开更多
Experimental results of the investigation on the hardness of two Al-Zn-Mg alloys [Al-10.0 Zn-4.0 Mg and Al-8.5 Zn-3.0 Mg (wt pct)] aged in the temperature range 60～310℃ for different intervals of time from 1/4 h to ...Experimental results of the investigation on the hardness of two Al-Zn-Mg alloys [Al-10.0 Zn-4.0 Mg and Al-8.5 Zn-3.0 Mg (wt pct)] aged in the temperature range 60～310℃ for different intervals of time from 1/4 h to 168 h are presented. Both the alloys were found to show identical behaviour of hardness with ageing time. Alloy with higher Zn and Mg content had higher hardness than the alloy with lower solute content. There were three ranges of temperature in which different types of precipitates formed and affected the hardness. Some of the grain boundaries were found to migrate and precipitate free zone has been observed.展开更多
The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C ...The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C to 400°C was investigated. The microstructure evolution during the aging treatment was characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that the plate-like bainite precipitates distribute homogeneously within austenitic grains and at grain boundaries. The volume fraction of bainite increases with the increase in aging temperature and aging time, which substantially improves the martensitic transformation critical stress of the alloy, whereas the bainite only slightly affects the superelasticity. This behavior is attributed to a coherent relationship between the bainite and the austenite, as well as to the bainite and the martensite exhibiting the same crystal structure. The variations of the martensitic transformation critical stress and the superelasticity of columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with aging-temperature and aging time are described by the Austin-Rickett equation, where the activation energy of bainite precipitation is 77.2 kJ ·mol1. Finally, a columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with both excellent superelasticity（5%-9%） and high martensitic transformation critical stress（443-677 MPa） is obtained through the application of the appropriate aging treatments.展开更多
The microplasma oxidation process of LY 12 Al alloy in Na2SiO3-KOH-NaAL2 system has been studied. The voltage-time curve of oxidation process is changed with the variation of current ...The microplasma oxidation process of LY 12 Al alloy in Na2SiO3-KOH-NaAL2 system has been studied. The voltage-time curve of oxidation process is changed with the variation of current densities. The voltage breakdown and hardness of coating increase with increasing current density. The phase composition, morphologies, element and the distribution of ceramic coating are investigated by XRD, EPMA.展开更多
The effect of Ta addition on the martensitic transformation characteristics and the X-ray visibility on NiTi shape memory alloy have been studied in (Ni51Ti49)1-xTax system. It was found that the transformation temper...The effect of Ta addition on the martensitic transformation characteristics and the X-ray visibility on NiTi shape memory alloy have been studied in (Ni51Ti49)1-xTax system. It was found that the transformation temperatures of the Ni51Ti49 binary alloy increased drastically by an addition of 0～4 at. pet Ta, but only slightly when the concentration exceeded 4 at. pct; the addition of Ta greatly decreases the sensitivity of the martensitic transformations to the variation in the Ni-Ti ratio. The addition of Ta to the NiTi binary alloy can improve its X-ray visibility.展开更多
The effects of temperature on corrosion and the electrochemical behavior of Ni82.3Cr7Fe3Si4.5B3.2 glassy alloy in HC1,H2SO4,and H3PO4 acids were studied using AC and DC techniques.Impedance data reveal that the suscep...The effects of temperature on corrosion and the electrochemical behavior of Ni82.3Cr7Fe3Si4.5B3.2 glassy alloy in HC1,H2SO4,and H3PO4 acids were studied using AC and DC techniques.Impedance data reveal that the susceptibility to localized corrosion increases with increasing temperature.Potentiodynamic polarization curves reveal that the bulk glassy alloy is spontaneously passivated at all the investigated temperature in H2SO4 and H3PO4 solutions.A localized corrosion effect in HCl solution is clearly observed.The apparent activation energies in the regions of Tafel,active,and passive,as well as the enthalpies and entropies of the dissolution process were determined and discussed.The high apparent activation energy（Ea） value for H3PO4 solution in Tafel region is explained by the low aggressivity of PO4^3- ions.展开更多
The magnetic properties, structure defects of electrodeposited Fe-Ni-P alloys with various compositions and the thermostability at amorphous state have been studied by DSC, positron annihilation and electronic integra...The magnetic properties, structure defects of electrodeposited Fe-Ni-P alloys with various compositions and the thermostability at amorphous state have been studied by DSC, positron annihilation and electronic integrating instrument methods. The results show that the thermostability of amorphous Fe-Ni-P alloys increases with Fe content. Emergence and recrystallization of stable phases defer as the P content of the coating increases. The minimum H-c, B-r and P-h occur at 9.4 P (wt pet) content. Maximum H-c, B-r and P-h occur at the weight ratio of Fe to Ni equaling to 1/9.展开更多
Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at ...Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at 850℃ was investigated; and the Al-B master alloys formed under different temperature conditions have been studied to explore the morphologies of AIB2 particles; slowly cooled sample with addition of Al-B was made to explore the refinement mechanism. AI-B master alloy can refine not only a-AI, but eutectic Si. Theoretical analysis indicates that, although AIB2 does not take part directly in the nucleation process in pure Al in the presence of Si, it provides a substrate for precipitation of a small content of Si from which a-At will grow without any undercooling. When the temperature decreases to eutectic line, AIB2 subsequently nucleates eutectic Si; AIB2 particles appear in two different morphologies, namely, hexagonal platelet and tetradehedron morphology which depend on the processing temperature conditions.展开更多
The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current i...The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current intensity of the traveling magnetic field has a great influence on the mechanical properties of the ZL205 A castings. When the excitation current intensity is 15 A, the tensile strength and elongation of ZL205 A alloy castings increase 27.2% and 67.7%, respectively, compared with those of the same alloy solidified under gravity. The improvement of mechanical properties is attributed to the decrease of micro-porosity in the alloy. Under the traveling magnetic field, the feeding pressure in the alloy melt before solidification can be enhanced due to the electromagnetic force. Moreover, the melt flow induced by the traveling magnetic field can decrease the temperature gradient. The feeding resistance will be increased because the temperature gradient decrease. So traveling magnetic field has an optimum effect on feeding.展开更多
A two-way shape memory effect (TWSM E) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM ) observations. Based on the analysis of the ...A two-way shape memory effect (TWSM E) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM ) observations. Based on the analysis of the microstructure after training. the mechanism of TWSME in the Ti46.3 Ni44.7Nb9 alloy has been discussed.展开更多
The effect of thermal cycling under loading on martensitic transformation and two-way shape memory effect was investigated for Ti-49.8 at, pet Ni alloy. It is shown that M(s), and M(f) temperature increase with increa...The effect of thermal cycling under loading on martensitic transformation and two-way shape memory effect was investigated for Ti-49.8 at, pet Ni alloy. It is shown that M(s), and M(f) temperature increase with increasing the number of cycles, while A(s) and A(f) temperature decrease during thermal cycling. The total strain at and permanent strain epsilon (p) increase with increasing applied stress and number of cycles. The two-way shape memory effect can be improved by proper thermal cycling training under loading, while excessively high applied stress results in the deterioration of TWSME. The reason for the changes in martensitic transformation characteristics and two-way shape memory effect during thermal cycling under loading is discussed based on the analysis of microstructure by TEM observations.展开更多
The effects of non-magnetic atom vacancy on structural, martensitic phase transitions and the corresponding magnetocMoric effect in MnCoGel-x alloys are investigated using x-ray diffraction and magnetic measurements. ...The effects of non-magnetic atom vacancy on structural, martensitic phase transitions and the corresponding magnetocMoric effect in MnCoGel-x alloys are investigated using x-ray diffraction and magnetic measurements. The introduction of non-magnetic atom vacancy leads to the decrease of the martensitic transition temperature and realizes a temperature window where magnetic and martensitic phase transitions can be tuned together. Moreover, the giant magnetocaloric effect accompanied with the coupled magnetic-structural transition is ob- tained. It is observed that the peak values of magnetic entropy change of MnCoGeo.97 are about -13.9, -35.1 and -47.4J.kg-1K-1 for △H = 2, 5, 7T, respectively.展开更多
Precipitation reactions in the differential scanning calorimetry （DSC） of an Al-Cu-Mg-Ag alloy were identified by analyzing the results from hardness test,electrical conductivity test,and transmission electron micro...Precipitation reactions in the differential scanning calorimetry （DSC） of an Al-Cu-Mg-Ag alloy were identified by analyzing the results from hardness test,electrical conductivity test,and transmission electron microscope （TEM） examination.It is discovered that thermal effects can be identified through selected area electron diffraction and bright-field images.The reaction peaks around 171,231,and 276℃ can be attributed to a structural rearrangement of coherent zones,to the precipitation of Ω phases,and to the precipitation of Ω and θ＇ and possible combination with the transition of θ＇→θ,respectively.In addition,the hardness and electrical conductivity of the alloy change proportionately with the progression of reactions during the heating process.This phenomenon can be attributed to the evolution of the micro-structure.展开更多
Analytical electron microscopy methods have been used to establish correlatjons between lattice parameters and phase compositions in binary TiAl and ternary TiAlCr alloys based on Ti-48 at.-%Al.On traversing the stoic...Analytical electron microscopy methods have been used to establish correlatjons between lattice parameters and phase compositions in binary TiAl and ternary TiAlCr alloys based on Ti-48 at.-%Al.On traversing the stoichiometric composition in the binary TiAl system the lattice parameters show linear relationships with Al concentration suggesting antisite defects influence the structural parameters. The relationship between lattice parameters and phase composition in the ternary TiAl (Cr) phase is influenced by the site occupation behaviour of Cr in the TiAl lattice. Comparisons are made between' bulk' and' local' measurements for obtaining such information in complex two-phase alloys. Possible implications for the mechanical properties are briefly discussed.展开更多
Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heatin...Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heating was performed at the same constant rate of increasing temperature while cooling was carried out at different rates of decreasing temperature. For each cooling rate, the temperature decreased in the same thermal interval. During each cooling stage, an exothermic peak（maximum） was observed on the DSC thermogram. This peak was associated with forward martensitic transformation. The DSC thermograms were analyzed with PROTEUS software： the critical martensitic transformation start（Ms） and finish（Mf） temperatures were determined by means of integral and tangent methods, and the dissipated heat was evaluated by the area between the corresponding maximum plot and a sigmoid baseline. The effects of the increase in cooling rate, assessed from a calorimetric viewpoint, consisted in the augmentation of the exothermic peak and the delay of direct martensitic transformation. The latter had the tendency to move to lower critical transformation temperatures. The martensite plates changed in morphology by becoming more oriented and by an augmenting in surface relief, which corresponded with the increase in cooling rate as observed by scanning electron microscopy（SEM） and atomic force microscopy（AFM）.展开更多
Residual electrical resistivity due to short-range order has been calculated for Cu100-xAlx (x=9.13,13.56, 14.5 and 14.76 in at pct) alloys using pseudopotential approach, and the results have been discussed in the li...Residual electrical resistivity due to short-range order has been calculated for Cu100-xAlx (x=9.13,13.56, 14.5 and 14.76 in at pct) alloys using pseudopotential approach, and the results have been discussed in the light of experimental studies of the local-order structure of these alloys. In case of Cu85.5Al14.5, change in the total residual electrical resistivity due to neutron-irradiation effects has been estimated by including contributions from the short-range order and static atomic displacement correction. Our results show a decrease in the residual resistivity in the irradiated Cu-Al solid solution as compared to the unirradiated sample. This is in accordance with the experimental results展开更多
基金financially supported by the National Key Research and Development Program of China(No.2016YFB0701202)the National Natural Science Foundation of China(General Program No.51474149 and Key Program No.51631006)
文摘Generalized stacking-fault energies （GSFEs） of basal-plane stacking faults 11 and 12 in Mg alloys have been studied based on first-principles calculations, where 43 alloying elements were considered. It is found that the most contributing features of alloying elements to GSFEs are bulk modulus, equilibrium volume, binding energy, atomic radius and ionization energy. Both bulk modulus and ionization energy exhibit positive relationships with GSFEs, and the others show opposite relationships. Multiple regressions have been performed to offer a quantitative prediction for basal-plane GSFEs in Mg-X systems. GSFEs, alloying effects of elements and the prediction model established within this work may provide guidelines for new Mg alloys design with better ductility.
文摘The effects of ternary solutes Ti, Co, V, Cr, Ta, W and Mo on the D03 phase 5tability of Fe3Alintermetallics are investigated by tight-binding linear Muffin-tin orbitaI method. The predictedsite preference5 of these elements in Fe3AI are in agreement with the experimental observations.The calculated Iocal magnetic moment of Fe3AI is identical to the experimentaI. ln addition, itis found that the D03 phase stability of Fe3AI doped with Ti, V, Co and Cr depends on 'energygap- of energy band near Fermi level. while the D03 phase stability of Fe3AI doped with Ta, Wand Mo may be affected by Madelung energy.
文摘The Mo 5Si 3 base alloys with a series of transition metal elements were prepared by arc melting, and were annealed at 1?250?℃ in vacuum for 24?h. Ternary alloying effect was investigated by X ray diffractometry (XRD), optical microscopy, scanning electron microscopy (SEM) and energy dispersive spectroscopy(EDS). The EDS results show that Zr, Ti, Co and V have certain solubility in homogenized Mo 5Si 3, which are determined to be 2.20±1.42, 15.94±0.18, 3.33±0.76 and 7.43±0.22 (mole fraction, %), respectively. Microstructural characteristics indicate that all studied alloys have a two phase microstructure, i.e., Mo 5Si 3 matrix and the second phase Mo 37 Zr 20 Si 43 , Mo 66 Si 19 Ti 15 , MoCoSi or (Mo, V) 3Si.
文摘The alloying effect of cerium in low carbon granular bainitic steel has been studied. Cerium increases the incubation time of granular bainitic transformation, exerts an influence on the morphology of nucleation and growth of bainitic transformation, and refines the structure of normalized granular bainite.
基金supported by the National Natural Science Foundations of China(51464032)the National Basic Research Program of China(grant No.2010CB635106)
文摘The application of segmental semi-solid thixoforming of magnesium alloys is confined due to the dimensional distinction existing in solid particles of the alloy billet from edge to center zones. In the present study, the effects of Sm addition on the microstructural evolution of Mg-6Zn-0.4Zr and Mg-6Zn-4Sm-0.4Zr alloys by semi-solid isothermal heat treatment were investigated, to obtain optimum semi-solid microstructures for the subsequently thixoforming. The results indicate that the grains of the Sm-bearing alloy are evidently refined and gradually evolve from dendritic to globular and elliptic particles. In addition, the distinctly dimensional effect of the Mg-6Zn-0.4Zr alloy is eliminated with 4% Sm addition; the particle sizes in all zones from center to the edge of the billet are almost identical. With the increment of isothermal heat treatment temperature, the dendritic microstructures completely disappear, and meanwhile, the irregular and globular particles gradually form. The size, morphology and the distribution of solid particles mainly depend on the formation and permeation of the liquid phase in the process of isothermal heat treatment. As the isothermal temperature increases from 570 °C to 610 °C, the average size and shape factor of solid particles of both the alloys with and without Sm addition gradually decrease while the liquid fraction gradually increases.
文摘Experimental results of the investigation on the hardness of two Al-Zn-Mg alloys [Al-10.0 Zn-4.0 Mg and Al-8.5 Zn-3.0 Mg (wt pct)] aged in the temperature range 60～310℃ for different intervals of time from 1/4 h to 168 h are presented. Both the alloys were found to show identical behaviour of hardness with ageing time. Alloy with higher Zn and Mg content had higher hardness than the alloy with lower solute content. There were three ranges of temperature in which different types of precipitates formed and affected the hardness. Some of the grain boundaries were found to migrate and precipitate free zone has been observed.
基金financially supported by the National Natural Science Foundation of China (Nos. 51574027 and 51604206)the Financial Support from the State Key Laboratory for Advanced Metals and Materials (No. 2016Z-22)
文摘The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C to 400°C was investigated. The microstructure evolution during the aging treatment was characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that the plate-like bainite precipitates distribute homogeneously within austenitic grains and at grain boundaries. The volume fraction of bainite increases with the increase in aging temperature and aging time, which substantially improves the martensitic transformation critical stress of the alloy, whereas the bainite only slightly affects the superelasticity. This behavior is attributed to a coherent relationship between the bainite and the austenite, as well as to the bainite and the martensite exhibiting the same crystal structure. The variations of the martensitic transformation critical stress and the superelasticity of columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with aging-temperature and aging time are described by the Austin-Rickett equation, where the activation energy of bainite precipitation is 77.2 kJ ·mol1. Finally, a columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with both excellent superelasticity（5%-9%） and high martensitic transformation critical stress（443-677 MPa） is obtained through the application of the appropriate aging treatments.
文摘The microplasma oxidation process of LY 12 Al alloy in Na2SiO3-KOH-NaAL2 system has been studied. The voltage-time curve of oxidation process is changed with the variation of current densities. The voltage breakdown and hardness of coating increase with increasing current density. The phase composition, morphologies, element and the distribution of ceramic coating are investigated by XRD, EPMA.
基金Shanxi Province Natural Science FOundation State Key Laboratory of Solidilication Processing.
文摘The effect of Ta addition on the martensitic transformation characteristics and the X-ray visibility on NiTi shape memory alloy have been studied in (Ni51Ti49)1-xTax system. It was found that the transformation temperatures of the Ni51Ti49 binary alloy increased drastically by an addition of 0～4 at. pet Ta, but only slightly when the concentration exceeded 4 at. pct; the addition of Ta greatly decreases the sensitivity of the martensitic transformations to the variation in the Ni-Ti ratio. The addition of Ta to the NiTi binary alloy can improve its X-ray visibility.
基金supported by the Kink Abdulaziz City of Science and Technology (KACST) (No.GSP–14–105)
文摘The effects of temperature on corrosion and the electrochemical behavior of Ni82.3Cr7Fe3Si4.5B3.2 glassy alloy in HC1,H2SO4,and H3PO4 acids were studied using AC and DC techniques.Impedance data reveal that the susceptibility to localized corrosion increases with increasing temperature.Potentiodynamic polarization curves reveal that the bulk glassy alloy is spontaneously passivated at all the investigated temperature in H2SO4 and H3PO4 solutions.A localized corrosion effect in HCl solution is clearly observed.The apparent activation energies in the regions of Tafel,active,and passive,as well as the enthalpies and entropies of the dissolution process were determined and discussed.The high apparent activation energy（Ea） value for H3PO4 solution in Tafel region is explained by the low aggressivity of PO4^3- ions.
文摘The magnetic properties, structure defects of electrodeposited Fe-Ni-P alloys with various compositions and the thermostability at amorphous state have been studied by DSC, positron annihilation and electronic integrating instrument methods. The results show that the thermostability of amorphous Fe-Ni-P alloys increases with Fe content. Emergence and recrystallization of stable phases defer as the P content of the coating increases. The minimum H-c, B-r and P-h occur at 9.4 P (wt pet) content. Maximum H-c, B-r and P-h occur at the weight ratio of Fe to Ni equaling to 1/9.
基金Shandong Natural Foundation !(Grant No:Z99F01)the Natiotal Natals Science Foundation of China !(Grant NO.59671046).
文摘Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at 850℃ was investigated; and the Al-B master alloys formed under different temperature conditions have been studied to explore the morphologies of AIB2 particles; slowly cooled sample with addition of Al-B was made to explore the refinement mechanism. AI-B master alloy can refine not only a-AI, but eutectic Si. Theoretical analysis indicates that, although AIB2 does not take part directly in the nucleation process in pure Al in the presence of Si, it provides a substrate for precipitation of a small content of Si from which a-At will grow without any undercooling. When the temperature decreases to eutectic line, AIB2 subsequently nucleates eutectic Si; AIB2 particles appear in two different morphologies, namely, hexagonal platelet and tetradehedron morphology which depend on the processing temperature conditions.
基金financially supported by the National Basic Research Program of China(2011CB610406)the Natural Science Foundation of Hei Longjiang Province(JC201209)the National Natural Science Foundation of China(51425402)
文摘The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current intensity of the traveling magnetic field has a great influence on the mechanical properties of the ZL205 A castings. When the excitation current intensity is 15 A, the tensile strength and elongation of ZL205 A alloy castings increase 27.2% and 67.7%, respectively, compared with those of the same alloy solidified under gravity. The improvement of mechanical properties is attributed to the decrease of micro-porosity in the alloy. Under the traveling magnetic field, the feeding pressure in the alloy melt before solidification can be enhanced due to the electromagnetic force. Moreover, the melt flow induced by the traveling magnetic field can decrease the temperature gradient. The feeding resistance will be increased because the temperature gradient decrease. So traveling magnetic field has an optimum effect on feeding.
文摘A two-way shape memory effect (TWSM E) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM ) observations. Based on the analysis of the microstructure after training. the mechanism of TWSME in the Ti46.3 Ni44.7Nb9 alloy has been discussed.
文摘The effect of thermal cycling under loading on martensitic transformation and two-way shape memory effect was investigated for Ti-49.8 at, pet Ni alloy. It is shown that M(s), and M(f) temperature increase with increasing the number of cycles, while A(s) and A(f) temperature decrease during thermal cycling. The total strain at and permanent strain epsilon (p) increase with increasing applied stress and number of cycles. The two-way shape memory effect can be improved by proper thermal cycling training under loading, while excessively high applied stress results in the deterioration of TWSME. The reason for the changes in martensitic transformation characteristics and two-way shape memory effect during thermal cycling under loading is discussed based on the analysis of microstructure by TEM observations.
基金Supported by the National Natural Science Foundation of China under Grant No 11504222
文摘The effects of non-magnetic atom vacancy on structural, martensitic phase transitions and the corresponding magnetocMoric effect in MnCoGel-x alloys are investigated using x-ray diffraction and magnetic measurements. The introduction of non-magnetic atom vacancy leads to the decrease of the martensitic transition temperature and realizes a temperature window where magnetic and martensitic phase transitions can be tuned together. Moreover, the giant magnetocaloric effect accompanied with the coupled magnetic-structural transition is ob- tained. It is observed that the peak values of magnetic entropy change of MnCoGeo.97 are about -13.9, -35.1 and -47.4J.kg-1K-1 for △H = 2, 5, 7T, respectively.
文摘Precipitation reactions in the differential scanning calorimetry （DSC） of an Al-Cu-Mg-Ag alloy were identified by analyzing the results from hardness test,electrical conductivity test,and transmission electron microscope （TEM） examination.It is discovered that thermal effects can be identified through selected area electron diffraction and bright-field images.The reaction peaks around 171,231,and 276℃ can be attributed to a structural rearrangement of coherent zones,to the precipitation of Ω phases,and to the precipitation of Ω and θ＇ and possible combination with the transition of θ＇→θ,respectively.In addition,the hardness and electrical conductivity of the alloy change proportionately with the progression of reactions during the heating process.This phenomenon can be attributed to the evolution of the micro-structure.
文摘Analytical electron microscopy methods have been used to establish correlatjons between lattice parameters and phase compositions in binary TiAl and ternary TiAlCr alloys based on Ti-48 at.-%Al.On traversing the stoichiometric composition in the binary TiAl system the lattice parameters show linear relationships with Al concentration suggesting antisite defects influence the structural parameters. The relationship between lattice parameters and phase composition in the ternary TiAl (Cr) phase is influenced by the site occupation behaviour of Cr in the TiAl lattice. Comparisons are made between' bulk' and' local' measurements for obtaining such information in complex two-phase alloys. Possible implications for the mechanical properties are briefly discussed.
基金supported by the project PN-II-ID-PCE-2012-4-0033,contract 13/2013
文摘Different fragments of a hot-rolled and homogenized Cu–Zn–Al shape memory alloy（SMA） were subjected to thermal cycling by means of a differential scanning calorimetric（DSC） device. During thermal cycling, heating was performed at the same constant rate of increasing temperature while cooling was carried out at different rates of decreasing temperature. For each cooling rate, the temperature decreased in the same thermal interval. During each cooling stage, an exothermic peak（maximum） was observed on the DSC thermogram. This peak was associated with forward martensitic transformation. The DSC thermograms were analyzed with PROTEUS software： the critical martensitic transformation start（Ms） and finish（Mf） temperatures were determined by means of integral and tangent methods, and the dissipated heat was evaluated by the area between the corresponding maximum plot and a sigmoid baseline. The effects of the increase in cooling rate, assessed from a calorimetric viewpoint, consisted in the augmentation of the exothermic peak and the delay of direct martensitic transformation. The latter had the tendency to move to lower critical transformation temperatures. The martensite plates changed in morphology by becoming more oriented and by an augmenting in surface relief, which corresponded with the increase in cooling rate as observed by scanning electron microscopy（SEM） and atomic force microscopy（AFM）.
文摘Residual electrical resistivity due to short-range order has been calculated for Cu100-xAlx (x=9.13,13.56, 14.5 and 14.76 in at pct) alloys using pseudopotential approach, and the results have been discussed in the light of experimental studies of the local-order structure of these alloys. In case of Cu85.5Al14.5, change in the total residual electrical resistivity due to neutron-irradiation effects has been estimated by including contributions from the short-range order and static atomic displacement correction. Our results show a decrease in the residual resistivity in the irradiated Cu-Al solid solution as compared to the unirradiated sample. This is in accordance with the experimental results
