A hard problem that hinders the movement of waxy crude oil is wax deposition in oil pipelines.To ensure the safe operation of crude oil pipelines,an accurate model must be developed to predict the rate of wax depositi...A hard problem that hinders the movement of waxy crude oil is wax deposition in oil pipelines.To ensure the safe operation of crude oil pipelines,an accurate model must be developed to predict the rate of wax deposition in crude oil pipelines.Aiming at the shortcomings of the ENN prediction model,which easily falls into the local minimum value and weak generalization ability in the implementation process,an optimized ENN prediction model based on the IRSA is proposed.The validity of the new model was confirmed by the accurate prediction of two sets of experimental data on wax deposition in crude oil pipelines.The two groups of crude oil wax deposition rate case prediction results showed that the average absolute percentage errors of IRSA-ENN prediction models is 0.5476% and 0.7831%,respectively.Additionally,it shows a higher prediction accuracy compared to the ENN prediction model.In fact,the new model established by using the IRSA to optimize ENN can optimize the initial weights and thresholds in the prediction process,which can overcome the shortcomings of the ENN prediction model,such as weak generalization ability and tendency to fall into the local minimum value,so that it has the advantages of strong implementation and high prediction accuracy.展开更多
Titanium nitride thin films were deposited on silicon by high power impulse magnetron sputtering(HiPIMS)method at different frequencies(162-637 Hz)and pulse-on time(60-322μs).Response surface methodology(RSM)was empl...Titanium nitride thin films were deposited on silicon by high power impulse magnetron sputtering(HiPIMS)method at different frequencies(162-637 Hz)and pulse-on time(60-322μs).Response surface methodology(RSM)was employed to study the simultaneous effect of frequency and pulse-on time on the current waveforms and the crystallographic orientation,microstructure,and in particular,the deposition rate of titanium nitride at constant time and average power equal to 250 W.The crystallographic structure and morphology of deposited films were analyzed using XRD and FESEM,respectively.It is found that the deposition rate of HiPIMS samples is tremendously dependent on pulse-on time and frequency of pulses where the deposition rate changes from 4.5 to 14.5 nm/min.The regression equations and analyses of variance(ANOVA)reveal that the maximum deposition rate(equal to(17±0.8)nm/min)occurs when the frequency is 537 Hz and pulse-on time is 212μs.The experimental measurement of the deposition rate under this condition gives rise to the deposition rate of 16.7 nm/min that is in good agreement with the predicted value.展开更多
Wire arc additive manufacturing(WAAM)is a novel manufacturing technique by which high strength metal components can be fabricated layer by layer using an electric arc as the heat source and metal wire as feedstock,and...Wire arc additive manufacturing(WAAM)is a novel manufacturing technique by which high strength metal components can be fabricated layer by layer using an electric arc as the heat source and metal wire as feedstock,and offers the potential to produce large dimensional structures at much higher build rate and minimum waste of raw material.In the present work,a cold metal transfer(CMT)based additive manufacturing was carried out and the effect of deposition rate on the microstructure and mechanical properties of WAAM Ti-6Al-4V components was investigated.The microstructure of WAAM components showed similar microstructural morphology in all deposition conditions.When the deposition rate increased from 1.63 to 2.23 kg/h,the ultimate tensile strength(UTS)decreased from 984.6 MPa to 899.2 MPa and the micro-hardness showed a scattered but clear decline trend.展开更多
A new kind of plasma technology with both high deposition rate and low dilution ratio was developed under the calculation and analysis of the arc flame characteristics of plasma arc,the kinematics behavior of powder a...A new kind of plasma technology with both high deposition rate and low dilution ratio was developed under the calculation and analysis of the arc flame characteristics of plasma arc,the kinematics behavior of powder and powder's heating in the arc. Compared with normal plasma surfacing method, the idea using constricting nozzle with small orifice diameter, long plasma arc and increasing the distance from meeting point of the two beams of powder to workpiece, to achieve the goals of high deposition rate and low dilution ratio, was put forward here. In order to prove this idea, a set of experimental system was built up and obtained satisfied results including high deposition rate(more than 25 kg/h )and low dilution ratio(less than 5%). The success of this study offers a promising prospect for developing the powder plasma surface welding in China and may open a way to improve this technology further in efficiency and quality.展开更多
Continuous noise resistance calculation(CNRC)technique was used for online determination of the electroless nickel deposition rate on zirconium pretreated magnesium alloy.For this purpose,the noise resistance(R_n) var...Continuous noise resistance calculation(CNRC)technique was used for online determination of the electroless nickel deposition rate on zirconium pretreated magnesium alloy.For this purpose,the noise resistance(R_n) variation with time was calculated for the pretreated alloy surface in the electroless plating solution.The CNRC results were described by energy dispersive X-ray spectroscopy(EDS)and scanning electron microscopy(SEM)techniques.Also,potentiodynamic polarization and gravimetric measurements were used for determination of the electroless deposition rate at the same time period and the results were compared with the CNRC results.The Rn variation with plating time shows that the electroless plating consists of different stages with various deposition rates.The results of the CNRC and polarization methods were not in acceptable agreement due to the limitations of the polarization method for online monitoring of the deposition rate.However,the results of the gravimetric measurements were in complete agreement with the CNRC technique and so,the CNRC can be considered as suitable tool for online evaluation of the electroless deposition rate.展开更多
A new expression for calculating suspended fine-sediment deposition rate is developed based on theoretic analysis and experiments. The resulting equation is applied to simulation of fine sediment deposition in the rec...A new expression for calculating suspended fine-sediment deposition rate is developed based on theoretic analysis and experiments. The resulting equation is applied to simulation of fine sediment deposition in the reclaimed land in the Hangzhou Bay, China. The hydrodynamic environment in this area is solved by use of a long wave model, which gives the 2D-velocity field and considers bathymetric changes due to fine sediment deposition. The expression is proved convenient to use in engineering practice, and the predicted deposition rate agrees with the annual data available from field measurements from the first year to the third year after the construction of the long groin as a reclaiming method.展开更多
Carbon nanotubes （CNTs） were synthesized through the catalytic decomposition of a ferrocene-xylene mixture in a horizontal chemical vapor deposition reactor. The deposition rate of CNTs along the axial direction was...Carbon nanotubes （CNTs） were synthesized through the catalytic decomposition of a ferrocene-xylene mixture in a horizontal chemical vapor deposition reactor. The deposition rate of CNTs along the axial direction was measured. The morphology of CNTs was observed by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results showed that the deposition rate of CNTs along the axial direction first increased and later decreased, the position achieving the maximum deposition rate was influenced by the operating conditions. The morphologies of CNTs also changed along the axial direction.展开更多
Na-type bentonite is commonly used as a tunnel backfilling material to prevent groundwater and radionuclide migration during the construction of a geological disposal system for high-level radioactive waste in Japan. ...Na-type bentonite is commonly used as a tunnel backfilling material to prevent groundwater and radionuclide migration during the construction of a geological disposal system for high-level radioactive waste in Japan. However, host rock fractures with strong water flow can develop groundwater paths in the backfilling material. Especially, the alteration to Ca-type bentonite causes degradation of the barrier performance and accelerates the development of groundwater paths. Additionally, using cementitious materials gradually changes pH between 13 and 8. High alkaline groundwater results in high solubility of silicic acid; therefore, silicic acid is eluted from the host rock. Downstream, in the low alkaline area, the groundwater becomes supersaturated in silicic acid. This acid is deposited on Ca-type bentonite, thus leading to the clogging of the groundwater paths. In the present study, we investigate the silicic acid deposition rate on Ca-type bentonite under 288-323 K for depths greater or equal to 500 m. The results indicate that temperature does not affect the silicic acid deposition rate up to 323 K. However, in this temperature range, the deposition of silicic acid on Ca-type bentonite in backfilled tunnels results in clogging of the flow paths.展开更多
Mg-alloys have gained considerable attention in recent years for their outstanding properties such as lightweight,high specific strength,and corrosion resistance,making them attractive for applications in medical,aero...Mg-alloys have gained considerable attention in recent years for their outstanding properties such as lightweight,high specific strength,and corrosion resistance,making them attractive for applications in medical,aerospace,automotive,and other transport industries.However,their widespread application is hindered by their low formability at room temperature due to limited slip systems.Cast Mg-alloys have low mechanical properties due to the presence of casting defects such as porosity and anisotropy in addition to the high scrap.While casting methods benefit from established process optimization techniques for these problems,additive manufacturing methods are increasingly replacing casting methods in Mg alloys as they provide more precise control over the microstructure and allow specific grain orientations,potentially enabling easier optimization of anisotropy properties in certain applications.Although metal additive manufacturing(MAM)technology also results in some manufacturing defects such as inhomogeneous microstructural evolution and porosity and additively manufactured Mg alloy parts exhibit lower properties than the wrought parts,they in general exhibit superior properties than the cast counterparts.Thus,MAM is a promising technique to produce Mg alloy parts.Directed energy deposition processes,particularly wire arc directed energy deposition(WA-DED),have emerged as an advantageous additive manufacturing(AM)technique for metallic materials including magnesium alloys,offering advantages such as high deposition rates,improved material efficiency,and reduced production costs compared to subtractive processes.However,the inherent challenges associated with magnesium,such as its high reactivity and susceptibility to oxidation,pose unique hurdles in the application of this technology.This review paper delves into the progress made in the application of DED technology to Mg-alloys,its challenges,and prospects.Furthermore,the predominant imperfections,notably inhomogeneous microstructure evolution and porosity,observed in Mg-alloy components manufactured through DED are discussed.Additionally,the preventive measures implemented to counteract the formation of these defects are explored.展开更多
The southwestern Iran is one of the regions that are most prone to dust events.The objective of this study is the analysis of the spatial and temporal distributions of dust deposition rate as a key factor for finding ...The southwestern Iran is one of the regions that are most prone to dust events.The objective of this study is the analysis of the spatial and temporal distributions of dust deposition rate as a key factor for finding the relative impact of the dust.First,the monthly mean aerosol optical thickness(AOT)from Moderate Resolution Imaging Spectroradiometer(MODIS)was analyzed and compared with the dust amount variations from ground deposition rate(GDR),and the results were further used to investigate the spatial and temporal distributions of dust events in southwestern Iran for the period between 2014 and 2015.Moving air mass trajectories,using the Hybrid Single-Particle Lagrangian Integrated Trajectory(HYSPLIT)model,were proven to be a discriminator of their local and regional origin.The results from GDR analysis produced a correlation coefficient between dust event history and deposition rates at dust magnitudes of>0.93 that is meaningful at the 95%confidence level.Furthermore,the deposition rates varied from 3 g/m2 per month in summer to 10 g/m2 per month in spring and gave insight into the transport direction of the dust.Within the same time series,AOT correspondences with MODIS on Terra in four aerosol thickness layers(clean,thin,thick,and strong thick)were shown in relation to each other.The deepest mixed layers were observed in spring and summer with a thickness of approximately 3500 m above ground level in the study area.Investigations of ground-based observations were correlated with the same variations for each aerosol thickness layer from MODIS images and they can be applied to discriminate layers of aeolian dust from layers of other aerosols.Together,dust distribution plots from AOT participated to enhance mass calculations and estimation deposition rates from the thick and strong thick aerosol thickness layers using the results from GDR.Despite all the advances of AOT,under certain circumstances,ground-based observations are better able to represent aerosol conditions over the study area,which were tested in southwestern Iran,even though the low number of observations is a commonly acknowledged drawback of GDR.展开更多
Single variable and deposition weight methods were adopted in the experiment. The hafnium crystal bar was fabricated by the iodide process. Influence of hafnium filament temperature（K value）, temperature controlling...Single variable and deposition weight methods were adopted in the experiment. The hafnium crystal bar was fabricated by the iodide process. Influence of hafnium filament temperature（K value）, temperature controlling method, types of feed, and the loading methods on the deposition rate were studied. The results show that the K value, temperature control method, types of feed, and the loading methods have obvious effects on the deposition rate of the hafnium crystal bar. The deposition rate increases with the K value rising in the range of certain temperature;the salt bath controlling temperature method could effectively obtain the better deposition rate; the greater the contact areas of the feeds are, the faster the deposition rate is.So, the optimal iodide deposition techniques of preparing hafnium crystal bar are as follows： hafnium turnings as feed,molybdenum feed retainer charging, salt bath temperature controlling under the higher K value.展开更多
The radial basis function neural network is a popular supervised learning tool based on machinery learning technology.Its high precision having been proven,the radial basis function neural network has been applied in ...The radial basis function neural network is a popular supervised learning tool based on machinery learning technology.Its high precision having been proven,the radial basis function neural network has been applied in many areas.The accumulation of deposited materials in the pipeline may lead to the need for increased pumping power,a decreased flow rate or even to the total blockage of the line,with losses of production and capital investment,so research on predicting the wax deposition rate is significant for the safe and economical operation of an oil pipeline.This paper adopts the radial basis function neural network to predict the wax deposition rate by considering four main influencing factors,the pipe wall temperature gradient,pipe wall wax crystal solubility coefficient,pipe wall shear stress and crude oil viscosity,by the gray correlational analysis method.MATLAB software is employed to establish the RBF neural network.Compared with the previous literature,favorable consistency exists between the predicted outcomes and the experimental results,with a relative error of 1.5%.It can be concluded that the prediction method of wax deposition rate based on the RBF neural network is feasible.展开更多
This paper is to present an efficient approach to enriching the quantification model of human-riverine interactions and its anthropogenic impact by a retrospective study on one of the four most famous historical hydra...This paper is to present an efficient approach to enriching the quantification model of human-riverine interactions and its anthropogenic impact by a retrospective study on one of the four most famous historical hydraulic projects in China,the Tuoshan Weir.It was constructed in 833 AD and had trajectories of natural resilience and hydraulic engineering maturity more than thousand years.Extensive historical data and maturation procedure of the hydraulic system were used judiciously to examine the spatial patterns of the long-term water conservancy system with agriculture,urbanization and civilization of Ningbo City in Zhejiang Province,Southeast China.Interaction framework is assessed from historical perspective and the deposition rate(DR)is calculated by analyzing the continuous increase of the Tuoshan Weir height.The results show that the declining DR during the 1180 years guaranteed the beneficial role the Tuoshan Weir played in spite of some negative river responses caused by the increase of sediment deposition and decrease of fresh water-retention capacity.The following up revamped workings and well matured hydraulic system around the Tuoshan Weir also contribute a lot to the designed mission of the weir.We conclude that hydraulic system maturation is very important for the proper function and life span of huge hydraulic projects.展开更多
The role of deposition rate in the structural, optical and electrical properties of SnOthin films deposited by electron beam evaporation method is investigated by varying the deposition powers viz. 50, 75, and 100 W.T...The role of deposition rate in the structural, optical and electrical properties of SnOthin films deposited by electron beam evaporation method is investigated by varying the deposition powers viz. 50, 75, and 100 W.The structural characterization of the films is done by X-ray diffraction(XRD) technique. The surface morphology of the films is studied by scanning electron microscopy(SEM). Rutherford back scattering(RBS) measurements revealed the thickness of the films ranging from 200 nm to 400 and also a change in the concentration of oxygen vacancies which is found to be the maximum in the film deposited at the lowest deposition rate. Optical absorption spectrum is recorded using the UV–V is spectroscopy and the films are found to be transparent in nature. A shift in the absorption edge is observed and is attributed to a different level of allowed energy states in conduction band minimum. The Hall effect and electrical measurements show a variation in the carrier concentrations, mobility and resistivity of the films. In order to explore a better compromise in electrical and optical properties for transparent electrode applications, skin depths calculations are also done to find the optimized values of carrier concentration and mobility.展开更多
CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen （H2）/nitrogen （N2） and growth temperature of the selective area growth （SAG） method with metal organic chemical vapor deposit...CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen （H2）/nitrogen （N2） and growth temperature of the selective area growth （SAG） method with metal organic chemical vapor deposition （MOCVD）. The SAG template is obtained by nanospherical-lens photolithography. It is found that increasing the flow rate of 1-12 will change the CaN crystal shape from pyramid to vertical rod, while increasing the growth temperature will reduce the diameters of GaN rods to nanometer scale. Finally the CaN nanorods with smooth lateral surface and relatively good quality are obtained under the condition that the H2：N2 ratio is 1：1 and the growth temperature is 1030℃. The good crystal quality and orientation of GaN nanorods are confirmed by high resolution transmission electron microscopy. The cathodoluminescence spectrum suggests that the crystal and optical quality is also improved with increasing the temperature.展开更多
The magnetic field profiles,which are produced by three ways in the deposition chamber and plasma chamber of single coil divergent field MWECR CVD system,are investigated.The magnetic field gradient of these magnetic ...The magnetic field profiles,which are produced by three ways in the deposition chamber and plasma chamber of single coil divergent field MWECR CVD system,are investigated.The magnetic field gradient of these magnetic field profiles is obtained quantitatively by using Lorentz fit.The results indicate that the gradient value of the magnetic field profile near by the substrate,which is produced by a coil current with 137.7A if a SmCo permanent magnet is equipped under the substrate holder,is the largest;when the SmCo permanent magnet is taken away,the larger one is produced by the coil current with 137.7A and the smallest one produced by a coil current with 115.2A.High deposition rate of a-Si∶H film is observed near by the substrate with high magnetic field gradient.But uneven deposition rate along the radius of the sample holder is also found by infrared analysis technology when sample is deposited in magnetic field profile,which is produced by the coil current with 137.7A if the SmCo permanent magnet is equipped under the substrate holder.展开更多
The mechanical and frictional properties of ta-C coatings deposited on the substrate surface affect applications in the field of cutting tools and wear-resistant components.In this paper,the effect of bias parameters ...The mechanical and frictional properties of ta-C coatings deposited on the substrate surface affect applications in the field of cutting tools and wear-resistant components.In this paper,the effect of bias parameters on the performance of ta-C coatings was investigated based on high power impulse magnetron sputtering(HiPIMS)technology.The results show that bias voltage has a significant effect on the deposition rate,structure,and wear resistance of the coating.In the range of bias voltage−50 V to−200 V,the ta-C coating performance was the best under bias voltage−150 V.The thickness reached 530.4 nm,the hardness value reached 35.996 GPa,and the bonding force in-creased to 14.2 N.The maximum sp3 bond content was 59.53% at this condition.展开更多
Radionuclide dating techniques characterized by137Cs and210Pbex have recently been applied in the study of lake sediments around the world.In this study,a chronological series of sediment cores was established based o...Radionuclide dating techniques characterized by137Cs and210Pbex have recently been applied in the study of lake sediments around the world.In this study,a chronological series of sediment cores was established based on137Cs and210Pbex analyses along with the evaluation of sediment properties,such as particle size distribution,total organic carbon(TOC),carbonate content,and acid-insoluble residue,to study sediment accumulation rates,sediment sources,and responses to human activities in the Jiuzhaigou National Nature Reserve in southwestern China.In terms of the particle size distribution of sediments,silt content was the highest,and clay and sand contents were relatively low.The sediments displayed high TOC contents because of the significant amounts of vegetation grown in the lakes.The carbonate content was also high due to the overall geological background of carbonates in Jiuzhaigou.Carbonate content tended to decline from top to bottom in the sediment cores,whereas the acid-insoluble residue tended to increase.These results suggested that the depth variation of the environmental parameters of the sediments in two lakes in Jiuzhaigou would correspond to each other.The results indicated that the sediment rate of Jiuzhaigou was generally high with strong siltation,indicating that serious soil loss was induced by intensive human activities in the basin over the past decades.The increases in the mass accumulation rate,contents of acid-insoluble residue,and mean particle size during the periods of 1840–1900s,late 1930s–early 1950s,1966–1978,and2003–2006 revealed the occurrence of severe soil and water loss as a result of extensive agricultural expansion,large-scale deforestation,and road construction in Jiuzhaigou.The deposition rate and the properties of lacustrine sediments could reflect the significant impact of human activities on lake sedimentation during Jiuzhaigou′s history.展开更多
The aim of this research is to pulse co-deposit nano-CeO2 particles into Ni-W-B alloy coatings in order to improve the surface properties. The influence of pulse frequency and duty circle on deposition rate, microhard...The aim of this research is to pulse co-deposit nano-CeO2 particles into Ni-W-B alloy coatings in order to improve the surface properties. The influence of pulse frequency and duty circle on deposition rate, microhardness and microstructures, and the influence of heat treatment temperature on phase structures, microhardness and abrasivity of Ni-W-B-CeO2 composite coatings were investigated. The results indicated that the pulse co-deposition of nickel, tungsten, boron and nano-CeO2 particle from the bath which nano-CeO2 particle was suspended by high speed mechanical stirring led to the Ni-W-B-CeO2 composite coatings, possessing better microhardness and abrasion resistance when heat-treated at 400 ℃ for 1 h. The microhardness as-deposited with 636 Hz and the deposition rate with 0.0281 mm·h-1 was the highest at pulse frequency with 1000 Hz and pulse duty circle with 10%. Microstructures analysis displays that decreasing pulse duty cycle leads to refinement in grain structures and the improvement of microstructures. X-ray diffraction shows that the composite coating as-deposited was mainly in the amorphous state and partially crystallized, but when heat treated at 400 ℃, the crystallization trend was strengthened further.展开更多
The influences of mass concentration of nickel chloride hexahydrate, sodium borohydride, ethylenediamine, pH value, bath temperature on deposition rate were studied with orthogonal experiments by a series of pre-treat...The influences of mass concentration of nickel chloride hexahydrate, sodium borohydride, ethylenediamine, pH value, bath temperature on deposition rate were studied with orthogonal experiments by a series of pre-treatments on micro-diamond particle, and the optimized parameters were obtained. Both the morphology and the composition of original diamond and the diamond with Ni-B coating were analyzed by SEM and XRD respectively. The SEM image shows that the spherical Ni-B particle is coated upon diamond. XRD pattern shows that the coating compositions are Ni and Ni2B.展开更多
文摘A hard problem that hinders the movement of waxy crude oil is wax deposition in oil pipelines.To ensure the safe operation of crude oil pipelines,an accurate model must be developed to predict the rate of wax deposition in crude oil pipelines.Aiming at the shortcomings of the ENN prediction model,which easily falls into the local minimum value and weak generalization ability in the implementation process,an optimized ENN prediction model based on the IRSA is proposed.The validity of the new model was confirmed by the accurate prediction of two sets of experimental data on wax deposition in crude oil pipelines.The two groups of crude oil wax deposition rate case prediction results showed that the average absolute percentage errors of IRSA-ENN prediction models is 0.5476% and 0.7831%,respectively.Additionally,it shows a higher prediction accuracy compared to the ENN prediction model.In fact,the new model established by using the IRSA to optimize ENN can optimize the initial weights and thresholds in the prediction process,which can overcome the shortcomings of the ENN prediction model,such as weak generalization ability and tendency to fall into the local minimum value,so that it has the advantages of strong implementation and high prediction accuracy.
文摘Titanium nitride thin films were deposited on silicon by high power impulse magnetron sputtering(HiPIMS)method at different frequencies(162-637 Hz)and pulse-on time(60-322μs).Response surface methodology(RSM)was employed to study the simultaneous effect of frequency and pulse-on time on the current waveforms and the crystallographic orientation,microstructure,and in particular,the deposition rate of titanium nitride at constant time and average power equal to 250 W.The crystallographic structure and morphology of deposited films were analyzed using XRD and FESEM,respectively.It is found that the deposition rate of HiPIMS samples is tremendously dependent on pulse-on time and frequency of pulses where the deposition rate changes from 4.5 to 14.5 nm/min.The regression equations and analyses of variance(ANOVA)reveal that the maximum deposition rate(equal to(17±0.8)nm/min)occurs when the frequency is 537 Hz and pulse-on time is 212μs.The experimental measurement of the deposition rate under this condition gives rise to the deposition rate of 16.7 nm/min that is in good agreement with the predicted value.
基金Projects(52075317,51905333)supported by the National Natural Science Foundation of ChinaProject(IEC\NSFC\181278)supported by the Royal Society through International Exchanges 2018 Cost Share(China)Scheme+2 种基金Project(19YF1418100)supported by Shanghai Sailing Program,ChinaProjects(19511106400,19511106402)supported by Shanghai Science and Technology Committee Innovation,ChinaProject(19030501300)supported by Shanghai Local Colleges and Universities Capacity Building Special Plan,China。
文摘Wire arc additive manufacturing(WAAM)is a novel manufacturing technique by which high strength metal components can be fabricated layer by layer using an electric arc as the heat source and metal wire as feedstock,and offers the potential to produce large dimensional structures at much higher build rate and minimum waste of raw material.In the present work,a cold metal transfer(CMT)based additive manufacturing was carried out and the effect of deposition rate on the microstructure and mechanical properties of WAAM Ti-6Al-4V components was investigated.The microstructure of WAAM components showed similar microstructural morphology in all deposition conditions.When the deposition rate increased from 1.63 to 2.23 kg/h,the ultimate tensile strength(UTS)decreased from 984.6 MPa to 899.2 MPa and the micro-hardness showed a scattered but clear decline trend.
文摘A new kind of plasma technology with both high deposition rate and low dilution ratio was developed under the calculation and analysis of the arc flame characteristics of plasma arc,the kinematics behavior of powder and powder's heating in the arc. Compared with normal plasma surfacing method, the idea using constricting nozzle with small orifice diameter, long plasma arc and increasing the distance from meeting point of the two beams of powder to workpiece, to achieve the goals of high deposition rate and low dilution ratio, was put forward here. In order to prove this idea, a set of experimental system was built up and obtained satisfied results including high deposition rate(more than 25 kg/h )and low dilution ratio(less than 5%). The success of this study offers a promising prospect for developing the powder plasma surface welding in China and may open a way to improve this technology further in efficiency and quality.
文摘Continuous noise resistance calculation(CNRC)technique was used for online determination of the electroless nickel deposition rate on zirconium pretreated magnesium alloy.For this purpose,the noise resistance(R_n) variation with time was calculated for the pretreated alloy surface in the electroless plating solution.The CNRC results were described by energy dispersive X-ray spectroscopy(EDS)and scanning electron microscopy(SEM)techniques.Also,potentiodynamic polarization and gravimetric measurements were used for determination of the electroless deposition rate at the same time period and the results were compared with the CNRC results.The Rn variation with plating time shows that the electroless plating consists of different stages with various deposition rates.The results of the CNRC and polarization methods were not in acceptable agreement due to the limitations of the polarization method for online monitoring of the deposition rate.However,the results of the gravimetric measurements were in complete agreement with the CNRC technique and so,the CNRC can be considered as suitable tool for online evaluation of the electroless deposition rate.
文摘A new expression for calculating suspended fine-sediment deposition rate is developed based on theoretic analysis and experiments. The resulting equation is applied to simulation of fine sediment deposition in the reclaimed land in the Hangzhou Bay, China. The hydrodynamic environment in this area is solved by use of a long wave model, which gives the 2D-velocity field and considers bathymetric changes due to fine sediment deposition. The expression is proved convenient to use in engineering practice, and the predicted deposition rate agrees with the annual data available from field measurements from the first year to the third year after the construction of the long groin as a reclaiming method.
文摘Carbon nanotubes （CNTs） were synthesized through the catalytic decomposition of a ferrocene-xylene mixture in a horizontal chemical vapor deposition reactor. The deposition rate of CNTs along the axial direction was measured. The morphology of CNTs was observed by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results showed that the deposition rate of CNTs along the axial direction first increased and later decreased, the position achieving the maximum deposition rate was influenced by the operating conditions. The morphologies of CNTs also changed along the axial direction.
文摘Na-type bentonite is commonly used as a tunnel backfilling material to prevent groundwater and radionuclide migration during the construction of a geological disposal system for high-level radioactive waste in Japan. However, host rock fractures with strong water flow can develop groundwater paths in the backfilling material. Especially, the alteration to Ca-type bentonite causes degradation of the barrier performance and accelerates the development of groundwater paths. Additionally, using cementitious materials gradually changes pH between 13 and 8. High alkaline groundwater results in high solubility of silicic acid; therefore, silicic acid is eluted from the host rock. Downstream, in the low alkaline area, the groundwater becomes supersaturated in silicic acid. This acid is deposited on Ca-type bentonite, thus leading to the clogging of the groundwater paths. In the present study, we investigate the silicic acid deposition rate on Ca-type bentonite under 288-323 K for depths greater or equal to 500 m. The results indicate that temperature does not affect the silicic acid deposition rate up to 323 K. However, in this temperature range, the deposition of silicic acid on Ca-type bentonite in backfilled tunnels results in clogging of the flow paths.
文摘Mg-alloys have gained considerable attention in recent years for their outstanding properties such as lightweight,high specific strength,and corrosion resistance,making them attractive for applications in medical,aerospace,automotive,and other transport industries.However,their widespread application is hindered by their low formability at room temperature due to limited slip systems.Cast Mg-alloys have low mechanical properties due to the presence of casting defects such as porosity and anisotropy in addition to the high scrap.While casting methods benefit from established process optimization techniques for these problems,additive manufacturing methods are increasingly replacing casting methods in Mg alloys as they provide more precise control over the microstructure and allow specific grain orientations,potentially enabling easier optimization of anisotropy properties in certain applications.Although metal additive manufacturing(MAM)technology also results in some manufacturing defects such as inhomogeneous microstructural evolution and porosity and additively manufactured Mg alloy parts exhibit lower properties than the wrought parts,they in general exhibit superior properties than the cast counterparts.Thus,MAM is a promising technique to produce Mg alloy parts.Directed energy deposition processes,particularly wire arc directed energy deposition(WA-DED),have emerged as an advantageous additive manufacturing(AM)technique for metallic materials including magnesium alloys,offering advantages such as high deposition rates,improved material efficiency,and reduced production costs compared to subtractive processes.However,the inherent challenges associated with magnesium,such as its high reactivity and susceptibility to oxidation,pose unique hurdles in the application of this technology.This review paper delves into the progress made in the application of DED technology to Mg-alloys,its challenges,and prospects.Furthermore,the predominant imperfections,notably inhomogeneous microstructure evolution and porosity,observed in Mg-alloy components manufactured through DED are discussed.Additionally,the preventive measures implemented to counteract the formation of these defects are explored.
文摘The southwestern Iran is one of the regions that are most prone to dust events.The objective of this study is the analysis of the spatial and temporal distributions of dust deposition rate as a key factor for finding the relative impact of the dust.First,the monthly mean aerosol optical thickness(AOT)from Moderate Resolution Imaging Spectroradiometer(MODIS)was analyzed and compared with the dust amount variations from ground deposition rate(GDR),and the results were further used to investigate the spatial and temporal distributions of dust events in southwestern Iran for the period between 2014 and 2015.Moving air mass trajectories,using the Hybrid Single-Particle Lagrangian Integrated Trajectory(HYSPLIT)model,were proven to be a discriminator of their local and regional origin.The results from GDR analysis produced a correlation coefficient between dust event history and deposition rates at dust magnitudes of>0.93 that is meaningful at the 95%confidence level.Furthermore,the deposition rates varied from 3 g/m2 per month in summer to 10 g/m2 per month in spring and gave insight into the transport direction of the dust.Within the same time series,AOT correspondences with MODIS on Terra in four aerosol thickness layers(clean,thin,thick,and strong thick)were shown in relation to each other.The deepest mixed layers were observed in spring and summer with a thickness of approximately 3500 m above ground level in the study area.Investigations of ground-based observations were correlated with the same variations for each aerosol thickness layer from MODIS images and they can be applied to discriminate layers of aeolian dust from layers of other aerosols.Together,dust distribution plots from AOT participated to enhance mass calculations and estimation deposition rates from the thick and strong thick aerosol thickness layers using the results from GDR.Despite all the advances of AOT,under certain circumstances,ground-based observations are better able to represent aerosol conditions over the study area,which were tested in southwestern Iran,even though the low number of observations is a commonly acknowledged drawback of GDR.
基金financially supported by the National Technology Support Project of China (No. 2012BAB10B10)China–Russia Corporation Program, Ministry of Science (No.2010DFR50800)
文摘Single variable and deposition weight methods were adopted in the experiment. The hafnium crystal bar was fabricated by the iodide process. Influence of hafnium filament temperature（K value）, temperature controlling method, types of feed, and the loading methods on the deposition rate were studied. The results show that the K value, temperature control method, types of feed, and the loading methods have obvious effects on the deposition rate of the hafnium crystal bar. The deposition rate increases with the K value rising in the range of certain temperature;the salt bath controlling temperature method could effectively obtain the better deposition rate; the greater the contact areas of the feeds are, the faster the deposition rate is.So, the optimal iodide deposition techniques of preparing hafnium crystal bar are as follows： hafnium turnings as feed,molybdenum feed retainer charging, salt bath temperature controlling under the higher K value.
文摘The radial basis function neural network is a popular supervised learning tool based on machinery learning technology.Its high precision having been proven,the radial basis function neural network has been applied in many areas.The accumulation of deposited materials in the pipeline may lead to the need for increased pumping power,a decreased flow rate or even to the total blockage of the line,with losses of production and capital investment,so research on predicting the wax deposition rate is significant for the safe and economical operation of an oil pipeline.This paper adopts the radial basis function neural network to predict the wax deposition rate by considering four main influencing factors,the pipe wall temperature gradient,pipe wall wax crystal solubility coefficient,pipe wall shear stress and crude oil viscosity,by the gray correlational analysis method.MATLAB software is employed to establish the RBF neural network.Compared with the previous literature,favorable consistency exists between the predicted outcomes and the experimental results,with a relative error of 1.5%.It can be concluded that the prediction method of wax deposition rate based on the RBF neural network is feasible.
基金supported by National Natural Science Foundation of China(Grant No.40972198)Chinese Special Funds for Major State Basic Research Project(Grant No.2010CB732001)+1 种基金Brain Korea 21 Project in 2008 and from the Research Institute of Engineering Science,Seoul National University,State Key Laboratory of Geohazard Prevention and Geoenvironment Protection(Grant No.SKLGP2011K007)Chengdu University of Technology
文摘This paper is to present an efficient approach to enriching the quantification model of human-riverine interactions and its anthropogenic impact by a retrospective study on one of the four most famous historical hydraulic projects in China,the Tuoshan Weir.It was constructed in 833 AD and had trajectories of natural resilience and hydraulic engineering maturity more than thousand years.Extensive historical data and maturation procedure of the hydraulic system were used judiciously to examine the spatial patterns of the long-term water conservancy system with agriculture,urbanization and civilization of Ningbo City in Zhejiang Province,Southeast China.Interaction framework is assessed from historical perspective and the deposition rate(DR)is calculated by analyzing the continuous increase of the Tuoshan Weir height.The results show that the declining DR during the 1180 years guaranteed the beneficial role the Tuoshan Weir played in spite of some negative river responses caused by the increase of sediment deposition and decrease of fresh water-retention capacity.The following up revamped workings and well matured hydraulic system around the Tuoshan Weir also contribute a lot to the designed mission of the weir.We conclude that hydraulic system maturation is very important for the proper function and life span of huge hydraulic projects.
文摘The role of deposition rate in the structural, optical and electrical properties of SnOthin films deposited by electron beam evaporation method is investigated by varying the deposition powers viz. 50, 75, and 100 W.The structural characterization of the films is done by X-ray diffraction(XRD) technique. The surface morphology of the films is studied by scanning electron microscopy(SEM). Rutherford back scattering(RBS) measurements revealed the thickness of the films ranging from 200 nm to 400 and also a change in the concentration of oxygen vacancies which is found to be the maximum in the film deposited at the lowest deposition rate. Optical absorption spectrum is recorded using the UV–V is spectroscopy and the films are found to be transparent in nature. A shift in the absorption edge is observed and is attributed to a different level of allowed energy states in conduction band minimum. The Hall effect and electrical measurements show a variation in the carrier concentrations, mobility and resistivity of the films. In order to explore a better compromise in electrical and optical properties for transparent electrode applications, skin depths calculations are also done to find the optimized values of carrier concentration and mobility.
基金Supported by the Key Program of the National Natural Science Foundation of China under Grant No 61334009the National High Technology Research and Development Program of China under Grant No 2014AA032604
文摘CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen （H2）/nitrogen （N2） and growth temperature of the selective area growth （SAG） method with metal organic chemical vapor deposition （MOCVD）. The SAG template is obtained by nanospherical-lens photolithography. It is found that increasing the flow rate of 1-12 will change the CaN crystal shape from pyramid to vertical rod, while increasing the growth temperature will reduce the diameters of GaN rods to nanometer scale. Finally the CaN nanorods with smooth lateral surface and relatively good quality are obtained under the condition that the H2：N2 ratio is 1：1 and the growth temperature is 1030℃. The good crystal quality and orientation of GaN nanorods are confirmed by high resolution transmission electron microscopy. The cathodoluminescence spectrum suggests that the crystal and optical quality is also improved with increasing the temperature.
文摘The magnetic field profiles,which are produced by three ways in the deposition chamber and plasma chamber of single coil divergent field MWECR CVD system,are investigated.The magnetic field gradient of these magnetic field profiles is obtained quantitatively by using Lorentz fit.The results indicate that the gradient value of the magnetic field profile near by the substrate,which is produced by a coil current with 137.7A if a SmCo permanent magnet is equipped under the substrate holder,is the largest;when the SmCo permanent magnet is taken away,the larger one is produced by the coil current with 137.7A and the smallest one produced by a coil current with 115.2A.High deposition rate of a-Si∶H film is observed near by the substrate with high magnetic field gradient.But uneven deposition rate along the radius of the sample holder is also found by infrared analysis technology when sample is deposited in magnetic field profile,which is produced by the coil current with 137.7A if the SmCo permanent magnet is equipped under the substrate holder.
基金supported by the National Key R&D Program of China(No.2019YFE0123900)the National Natural Sci-ence Foundation of China(Grant No.51974069)the Special Fund for Basic Scientific Research of Central Colleges(N2125035).
文摘The mechanical and frictional properties of ta-C coatings deposited on the substrate surface affect applications in the field of cutting tools and wear-resistant components.In this paper,the effect of bias parameters on the performance of ta-C coatings was investigated based on high power impulse magnetron sputtering(HiPIMS)technology.The results show that bias voltage has a significant effect on the deposition rate,structure,and wear resistance of the coating.In the range of bias voltage−50 V to−200 V,the ta-C coating performance was the best under bias voltage−150 V.The thickness reached 530.4 nm,the hardness value reached 35.996 GPa,and the bonding force in-creased to 14.2 N.The maximum sp3 bond content was 59.53% at this condition.
基金Under the auspices of Programme of Introducing Talents of Discipline to Universities(the 111 Project)(No.B08037)National Key Technology R&D Program of China(No.2012BAC06B02)
文摘Radionuclide dating techniques characterized by137Cs and210Pbex have recently been applied in the study of lake sediments around the world.In this study,a chronological series of sediment cores was established based on137Cs and210Pbex analyses along with the evaluation of sediment properties,such as particle size distribution,total organic carbon(TOC),carbonate content,and acid-insoluble residue,to study sediment accumulation rates,sediment sources,and responses to human activities in the Jiuzhaigou National Nature Reserve in southwestern China.In terms of the particle size distribution of sediments,silt content was the highest,and clay and sand contents were relatively low.The sediments displayed high TOC contents because of the significant amounts of vegetation grown in the lakes.The carbonate content was also high due to the overall geological background of carbonates in Jiuzhaigou.Carbonate content tended to decline from top to bottom in the sediment cores,whereas the acid-insoluble residue tended to increase.These results suggested that the depth variation of the environmental parameters of the sediments in two lakes in Jiuzhaigou would correspond to each other.The results indicated that the sediment rate of Jiuzhaigou was generally high with strong siltation,indicating that serious soil loss was induced by intensive human activities in the basin over the past decades.The increases in the mass accumulation rate,contents of acid-insoluble residue,and mean particle size during the periods of 1840–1900s,late 1930s–early 1950s,1966–1978,and2003–2006 revealed the occurrence of severe soil and water loss as a result of extensive agricultural expansion,large-scale deforestation,and road construction in Jiuzhaigou.The deposition rate and the properties of lacustrine sediments could reflect the significant impact of human activities on lake sedimentation during Jiuzhaigou′s history.
基金Projects supported by Applied Basic Research Plans Programof Yunnan Province (2007E 187M)Scientific Research Fund(2006-02)Analysis and Measurement Research Fund (2007-22) of Kunming University of Science and Technology
文摘The aim of this research is to pulse co-deposit nano-CeO2 particles into Ni-W-B alloy coatings in order to improve the surface properties. The influence of pulse frequency and duty circle on deposition rate, microhardness and microstructures, and the influence of heat treatment temperature on phase structures, microhardness and abrasivity of Ni-W-B-CeO2 composite coatings were investigated. The results indicated that the pulse co-deposition of nickel, tungsten, boron and nano-CeO2 particle from the bath which nano-CeO2 particle was suspended by high speed mechanical stirring led to the Ni-W-B-CeO2 composite coatings, possessing better microhardness and abrasion resistance when heat-treated at 400 ℃ for 1 h. The microhardness as-deposited with 636 Hz and the deposition rate with 0.0281 mm·h-1 was the highest at pulse frequency with 1000 Hz and pulse duty circle with 10%. Microstructures analysis displays that decreasing pulse duty cycle leads to refinement in grain structures and the improvement of microstructures. X-ray diffraction shows that the composite coating as-deposited was mainly in the amorphous state and partially crystallized, but when heat treated at 400 ℃, the crystallization trend was strengthened further.
基金the National Key Technology R & D Program of MOST(No.2003BA328C)Chinese Nature Science Foundation Committee(No.50472043)+2 种基金Program for New Century Excellent Talents in University(No.NCET-06-0658)the Excellent Young Teachers Program of MOE(No.EYTP 2003-355)Science and Technology Key Project of MOE(No:Key 104136).
文摘The influences of mass concentration of nickel chloride hexahydrate, sodium borohydride, ethylenediamine, pH value, bath temperature on deposition rate were studied with orthogonal experiments by a series of pre-treatments on micro-diamond particle, and the optimized parameters were obtained. Both the morphology and the composition of original diamond and the diamond with Ni-B coating were analyzed by SEM and XRD respectively. The SEM image shows that the spherical Ni-B particle is coated upon diamond. XRD pattern shows that the coating compositions are Ni and Ni2B.
