Based on the advantage of phase coded signal and stepped frequency signal,a new hybrid modulation signal is introduced in this paper. It combines phase code modulation during the pulse with stepped frequency modulatio...Based on the advantage of phase coded signal and stepped frequency signal,a new hybrid modulation signal is introduced in this paper. It combines phase code modulation during the pulse with stepped frequency modulation between the pulses, which is named as phase-coded stepped-frequency ( PCSF ) signal. By analyzing its waveform and ambiguity function,the comparison between Stepped-Frequency ( SF) signal and PCSF signal is given,which shows that the PCSF signal is better than SF signal. Finally,the signal processing method with two stage compressed processing is presented. The simulation results show that this new hybrid modulation radar signal can get a higher stepped frequency than ordinary SF signal,realize the same equivalent bandwidth with less pulse number,and solve the conflict among the stepped frequency,the number of pulse, and transmit average power. Under the premises of a certain range resolution,this new hybrid modulation radar signal not only raises the data rate of radar system,but also reduces Doppler sensitivity with a good prospect, and the effect of one-dimensional range profile is much better than that of traditional SF signal. Therefore,this new hybrid modulation radar signal can be widely used in application.展开更多
A dual N-ary orthogonal hybrid modulation system is introduced in this paper, which can increase the data rate greatly compared with conventional N-ary orthogonal spread spectrum system, so it can be used for high rat...A dual N-ary orthogonal hybrid modulation system is introduced in this paper, which can increase the data rate greatly compared with conventional N-ary orthogonal spread spectrum system, so it can be used for high rate data communication. Then, three code recognition algorithms are presented for dual N-ary orthogonal hybrid modulation system and the analytic bit error rate （BER） performance of the system in additive white Gaussian noise （AWGN） and fiat Rayleigh fading channel is derived. Finally, the computer simulation of the system with three code recognition algorithms is performed, which shows that the simplified maximum a posteriori （MAP） algorithm is the best for the system with a compromise between the performance and the complexity.展开更多
Cascaded H-bridge inverter(CHBI) with supercapacitors(SCs) and dc-dc stage shows significant promise for medium to high voltage energy storage applications. This paper investigates the voltage balance of capacitors wi...Cascaded H-bridge inverter(CHBI) with supercapacitors(SCs) and dc-dc stage shows significant promise for medium to high voltage energy storage applications. This paper investigates the voltage balance of capacitors within the CHBI, including both the dc-link capacitors and SCs. Balance control over the dc-link capacitor voltages is realized by the dcdc stage in each submodule(SM), while a hybrid modulation strategy(HMS) is implemented in the H-bridge to balance the SC voltages among the SMs. Meanwhile, the dc-link voltage fluctuations are analyzed under the HMS. A virtual voltage variable is introduced to coordinate the balancing of dc-link capacitor voltages and SC voltages. Compared to the balancing method that solely considers the SC voltages, the presented method reduces the dc-link voltage fluctuations without affecting the voltage balance of SCs. Finally, both simulation and experimental results verify the effectiveness of the presented method.展开更多
In the context of next-generation optical access networks beyond 10 G, for high SE and flexible dynamic bandwidth allocation (DBA), the scheme of hybrid 64/16/4QAM-OFDM signal for downlink transmission and hybrid 16/8...In the context of next-generation optical access networks beyond 10 G, for high SE and flexible dynamic bandwidth allocation (DBA), the scheme of hybrid 64/16/4QAM-OFDM signal for downlink transmission and hybrid 16/8/QPSK-OFDM signal for uplink transmission is successfully proposed and experimentally presented in a full-duplex PON based on OFDM system. Here, for the uplink, in order to unit management of the optical line terminal (OLT) and reduce cost, the optical source functioned as the optical subcarrier at optical network units (ONUs) is from OLT in the central station. Moreover, there is an external cavity laser (ECL) with center frequency of 193.2 THz not only employed as optical modulated signal but also acted as LO signal. Our simulation results show that bit error ratio (BER) under hardware detection forward error correction has been successfully gained after 20 km of SSMF transmission. It is observed that the receiver sensitivity of multilevel PSK (M-PSK) is obviously larger than that of the M-QAM in this measurement scheme.展开更多
High performance electro-optic modulator,as the key device of integrated ultra-wideband optical systems,have be-come the focus of research.Meanwhile,the organic-based hybrid electro-optic modulators,which make full us...High performance electro-optic modulator,as the key device of integrated ultra-wideband optical systems,have be-come the focus of research.Meanwhile,the organic-based hybrid electro-optic modulators,which make full use of the advant-ages of organic electro-optic(OEO)materials(e.g.high electro-optic coefficient,fast response speed,high bandwidth,easy pro-cessing/integration and low cost)have attracted considerable attention.In this paper,we introduce a series of high-perform-ance OEO materials that exhibit good properties in electro-optic activity and thermal stability.In addition,the recent progress of organic-based hybrid electro-optic devices is reviewed,including photonic crystal-organic hybrid(PCOH),silicon-organic hy-brid(SOH)and plasmonic-organic hybrid(POH)modulators.A high-performance integrated optical platform based on OEO ma-terials is a promising solution for growing high speeds and low power consumption in compact sizes.展开更多
A compact wirebond packaged phase-leg SiC/Si hybrid module was designed,developed,and tested.Details of the layout and gate drive designs are described.The IC chip for gate drive is carefully selected and compared.Dua...A compact wirebond packaged phase-leg SiC/Si hybrid module was designed,developed,and tested.Details of the layout and gate drive designs are described.The IC chip for gate drive is carefully selected and compared.Dual pulse test confirmed that,the switching loss of hybrid module is close to pure SiC MOSFET module,and it is much less than pure Si IGBT device.The cost of hybrid module is closer to Si IGBT.展开更多
In this paper,the hybrid photovoltaic-thermoelectric generator(PVTEG)combined dynamic voltage restorer(DVR)system is proposed for the power quality disturbances compensation in a single-phase distribution system.The s...In this paper,the hybrid photovoltaic-thermoelectric generator(PVTEG)combined dynamic voltage restorer(DVR)system is proposed for the power quality disturbances compensation in a single-phase distribution system.The stable and precise level of input voltage is essential for the smooth and trouble-free operation of the electrically sensitive loads which are connected at the utility side to avoid system malfunctions.In this context,the hybrid PV-TEG energy module combined DVR system is proposed in this paper.With the support of the hybrid energy module,the DVR will perform the power quality disturbances compensation effectively with needed voltage and/or power.In the proposed system,the PV and TEG energy sources are connected electrically in series to produce adequate voltage for the DVR operation and the fractional factor-based variable incremental conduction(FFVINC)maximum power point tracking(MPPT)control algorithm is employed to extract the possible maximum power from the PV array.The intelligent fuzzy logic controller(FLC)is chosen for implementing the MPPT control algorithm.The half-bridge voltage source inverter(VSI)circuit and in-phase voltage compensation technique are used in the DVR for better power quality disturbances compensation.The performance and usefulness of the proposed DVR system are investigated by an extensive simulation study with four different modes of operation,the study results are confirmed that the proposed system promptly identifies the power quality disturbances for compensation.Moreover,the investigation proved that the combined PV and TEG energy module can provide better energy efficiency in converting solar irradiation into electricity.展开更多
Hybrid power sources have attracted much attention in the electric vehicle area. Particularly, electric-electric hybrid powertrain system consisting of supercapacitor modules and lithium-ion batteries has been widely ...Hybrid power sources have attracted much attention in the electric vehicle area. Particularly, electric-electric hybrid powertrain system consisting of supercapacitor modules and lithium-ion batteries has been widely applied because of the high power density of supercapacitors. In this study, we design a hybrid powertrain system containing two porous carbon electrode-based supercapacitor modules in parallel and one lithium ion battery pack. With the construction of the testing station, the performance and stability of the used supercapacitor modules are investigated in correlation with the structure of the supercapacitor and the nature of the electrode materials applied. It has been shown that the responding time for voltage vibration from 20 V to 48.5 V during charging or discharging process decreases from about 490 s to 94 s with the increase in applied current from 20 A to 100 A. The capacitance of the capacitor modules is nearly independent on the applied current. With the designed setup, the energy efficiency can reach as high as 0.99. The results described here provide a guidance for material selection of supercapacitors and optimized controlling strategy for hybrid power system applied in electric vehicles.展开更多
A one-dimensional fluid/Monte-Carlo（MC）hybrid model is developed to describe capacitively coupled SiH_4/Ar discharge,in which the lower electrode is applied by a RF source and pulse modulated by a square-wave,to inv...A one-dimensional fluid/Monte-Carlo（MC）hybrid model is developed to describe capacitively coupled SiH_4/Ar discharge,in which the lower electrode is applied by a RF source and pulse modulated by a square-wave,to investigate the modulation effects of the pulse duty cycle on the discharge mechanism.An electron Monte Carlo simulation is used to calculate the electron energy distribution as a function of position and time phase.Rate coefficients in chemical reactions can then be obtained and transferred to the fluid model for the calculation of electron temperature and densities of different species,such as electrons,ions,and radicals.The simulation results show that,the electron energy distribution f（ε）is modulated evidently within a pulse cycle,with its tail extending to higher energies during the power-on period,while shrinking back promptly in the afterglow period.Thus,the rate coefficients could be controlled during the discharge,resulting in modulation of the species composition on the substrate compared with continuous excitation.Meanwhile,more negative ions,like Si H_3^-and Si H_2^-,may escape to the electrodes owing to the collapse of ambipolar electric fields,which is beneficial to films deposition.Pulse modulation is thus expected to provide additional methods to customize the plasma densities and components.展开更多
In this paper, an improved hybrid space vector pulse width modulation (HSVPWM) technique is proposed for IM (induction motor) drives. The basic principle involved in the proposed random pulse width modulation (RPWM) c...In this paper, an improved hybrid space vector pulse width modulation (HSVPWM) technique is proposed for IM (induction motor) drives. The basic principle involved in the proposed random pulse width modulation (RPWM) cuddled SVPWM is amalgamating the pre-calculated switching timings for various sections of hexagonal space vector boundary and the random selection of carrier between two triangular signals, in order to disband acoustic switching noise spectrum with improved fundamental component. The arbitrary selection between triangular carriers, which is decided by digital signal states (Low or High) of the linear feedback shift register (LFSR) based pseudo random binary sequence (PRBS) generator. The SVPWM offers a control degree of freedom in terms of positioning of vectors inside every sampling interval and hence it has six possible variants of the voltage vectors arrangements in each sector. The developed HSVPWM is thoroughly analyzed in using the MATLAB? based simulation for all SVPWM variants. From the simulation and experimental results viz. harmonic spectrum, harmonic spread factor (HSF), total harmonic distortion (THD) etc., and the superiority of the proposed scheme such as better utilization of DC bus and the randomization of the harmonic power are evidenced. For the practical implementation, Xilinx XC3S500E FPGA device has been used.展开更多
Modulation of lower hybrid current drive was used successfully to suppress MHD activity. This was achieved in discharges with MHD m = 2 tearing modes during the discharge conditions Ip = 110 kA, Bt = 1.75 T, ne0 - 1.1...Modulation of lower hybrid current drive was used successfully to suppress MHD activity. This was achieved in discharges with MHD m = 2 tearing modes during the discharge conditions Ip = 110 kA, Bt = 1.75 T, ne0 - 1.1 × 1013 cm-3. The delivering time of LHCD pulse is less then 30 μs. The amplitude, interval and the period of LHCD modulation pulse can be adjusted very conveniently. The modulation LHCD can be delivered very fast at any time during the discharge. The modulation LHCD period was always much shorter than the plasma resistive time (Tη ≈100 ms). So the profile of plasma current is changed much faster than the plasma resistive time. The different forms of LHCD modulating can be proved.展开更多
SiC Hybrid switch(HyS)combines low conduction loss of Si IGBT and low switching loss of SiC MOSFET,and the cost is closer to that of Si IGBT.The promising high performances of HyS will bring considerable achievement i...SiC Hybrid switch(HyS)combines low conduction loss of Si IGBT and low switching loss of SiC MOSFET,and the cost is closer to that of Si IGBT.The promising high performances of HyS will bring considerable achievement in terms of enhancing power density of a converter system.By reviewing the gate drive pattern,gate drive hardware,current sharing,module design,converter design,and cost,this paper introduces state-of-the-art SiC HyS.展开更多
Based on the hybrid integration technology, an ultra-compact and low cost transmitter optical subassembly module is proposed. Four directly modulated lasers are combined with a coarse wavelength division multiplexer o...Based on the hybrid integration technology, an ultra-compact and low cost transmitter optical subassembly module is proposed. Four directly modulated lasers are combined with a coarse wavelength division multiplexer operated at the O-band. The bandwidth for all channels is measured to be approximately 3 GHz. The 112 Gb∕s transmission is experimentally demonstrated for a 10 km standard single mode fiber（SSMF）, in which an optical isolator is used for avoiding the back-reflected and scattered light to improve the bit error rate（BER） performance. A low BER and clear eye opening are achieved for 10 km transmission.展开更多
Multicarrier transmission systems like orthogonal frequency division multiplexing （OFDM） support high data rate and generally require no equalization at the receiver, making them simple and efficient. This paper stu...Multicarrier transmission systems like orthogonal frequency division multiplexing （OFDM） support high data rate and generally require no equalization at the receiver, making them simple and efficient. This paper studies the design and performance analysis of a hybrid modulation system derived from multifrequency and MQAM signals, employed in OFDM. This modulation scheme has better bit error rate （BER） performance and exhibits low PAPR. The proposed hybrid modulator reduces PAPR while keeping the OFDM transceiver design simple, as it does not require any side information or a little side information （only one bit） to be sent and is efficient for arbitrary number of subcarriers. The results of the implementations are compared with those of conventional OFDM system.展开更多
Wafer-level mass production of photonic integrated circuits(PIC)has become a technological mainstay in the field of optics and photonics,enabling many novel and disrupting a wide range of existing applications.However...Wafer-level mass production of photonic integrated circuits(PIC)has become a technological mainstay in the field of optics and photonics,enabling many novel and disrupting a wide range of existing applications.However,scalable photonic packaging and system assembly still represents a major challenge that often hinders commercial adoption of PIC-based solutions.Specifically,chip-to-chip and fiber-to-chip connections often rely on so-called active alignment techniques,where the coupling efficiency is continuously measured and optimized during the assembly process.This unavoidably leads to technically complex assembly processes and high cost,thereby eliminating most of the inherent scalability advantages of PIC-based solutions.In this paper,we demonstrate that 3D-printed facet-attached microlenses(FaML)can overcome this problem by opening an attractive path towards highly scalable photonic system assembly,relying entirely on passive assembly techniques based on industry-standard machine vision and/or simple mechanical stops.FaML can be printed with high precision to the facets of optical components using multi-photon lithography,thereby offering the possibility to shape the emitted beams by freely designed refractive or reflective surfaces.Specifically,the emitted beams can be collimated to a comparatively large diameter that is independent of the device-specific mode fields,thereby relaxing both axial and lateral alignment tolerances.Moreover,the FaML concept allows to insert discrete optical elements such as optical isolators into the free-space beam paths between PIC facets.We show the viability and the versatility of the scheme in a series of selected experiments of high technical relevance,comprising pluggable fiber-chip interfaces,the combination of PIC with discrete micro-optical elements such as polarization beam splitters,as well as coupling with ultra-low back-reflection based on non-planar beam paths that only comprise tilted optical surfaces.Based on our results,we believe that the FaML concept opens an attractive path towards novel PIC-based system architectures that combine the distinct advantages of different photonic integration platforms.展开更多
Background HEPS-BPIX is a prototype of photon counting pixel detector developed for the High Energy Photon Source.It consists of 16 silicon pixel modules which should be tested individually to ensure the function and ...Background HEPS-BPIX is a prototype of photon counting pixel detector developed for the High Energy Photon Source.It consists of 16 silicon pixel modules which should be tested individually to ensure the function and performance.Purpose Due to various factors such as the non-uniformity of the processes and voltage drop,the response of each pixel in the silicon pixel module is not identical completely.The response difference of pixels can be minimized by the threshold calibration.This system is developed for the quality test and calibration of the silicon pixel modules.Methods The system consists of a mother board,a control board and a data acquisition(DAQ)system.The mother board provides necessary resources including power supplies and the fanout of calibration signals.Besides,it can be used to test the connectivity by monitoring the power states.The control board reads data out and provides the clock,trigger and configuration data for the silicon pixel module.The DAQ system sends the control commands and receives the readout data through an Ethernet link.Results Compared with the previous readout system,this designed system has a lower noise level and better scanning curves making the calibration more accurate.And it has been successfully applied to the comparison experiments of the through silicon via and wire-bonding silicon pixel modules.Conclusion The results show that this test system can be used to the quality test and calibration of the silicon pixel modules.In addition,the system can be adapted to the measurement of different pixel array detector modules.展开更多
基金Sponsored by the Nation Nature Science Foundation of China(Grant No. 61201237)the Nature Science Foundation of Heilongjiang Province of China(Grant No. QC2012C069)the Fundationtal Research Funds for the Central Universities (Grant No. HEUCFZ1129, HEUCF130810,HEUCF130817)
文摘Based on the advantage of phase coded signal and stepped frequency signal,a new hybrid modulation signal is introduced in this paper. It combines phase code modulation during the pulse with stepped frequency modulation between the pulses, which is named as phase-coded stepped-frequency ( PCSF ) signal. By analyzing its waveform and ambiguity function,the comparison between Stepped-Frequency ( SF) signal and PCSF signal is given,which shows that the PCSF signal is better than SF signal. Finally,the signal processing method with two stage compressed processing is presented. The simulation results show that this new hybrid modulation radar signal can get a higher stepped frequency than ordinary SF signal,realize the same equivalent bandwidth with less pulse number,and solve the conflict among the stepped frequency,the number of pulse, and transmit average power. Under the premises of a certain range resolution,this new hybrid modulation radar signal not only raises the data rate of radar system,but also reduces Doppler sensitivity with a good prospect, and the effect of one-dimensional range profile is much better than that of traditional SF signal. Therefore,this new hybrid modulation radar signal can be widely used in application.
基金the National Basic Research Program of China(No5130601)Jiangsu Provincial Natural Science Foundation(NoBK2006701)
文摘A dual N-ary orthogonal hybrid modulation system is introduced in this paper, which can increase the data rate greatly compared with conventional N-ary orthogonal spread spectrum system, so it can be used for high rate data communication. Then, three code recognition algorithms are presented for dual N-ary orthogonal hybrid modulation system and the analytic bit error rate （BER） performance of the system in additive white Gaussian noise （AWGN） and fiat Rayleigh fading channel is derived. Finally, the computer simulation of the system with three code recognition algorithms is performed, which shows that the simplified maximum a posteriori （MAP） algorithm is the best for the system with a compromise between the performance and the complexity.
基金supported in part by the CAS Project for Young Scientists in Basic Research under Grant No. YSBR-045the Youth Innovation Promotion Association CAS under Grant 2022137the Institute of Electrical Engineering CAS under Grant E155320101。
文摘Cascaded H-bridge inverter(CHBI) with supercapacitors(SCs) and dc-dc stage shows significant promise for medium to high voltage energy storage applications. This paper investigates the voltage balance of capacitors within the CHBI, including both the dc-link capacitors and SCs. Balance control over the dc-link capacitor voltages is realized by the dcdc stage in each submodule(SM), while a hybrid modulation strategy(HMS) is implemented in the H-bridge to balance the SC voltages among the SMs. Meanwhile, the dc-link voltage fluctuations are analyzed under the HMS. A virtual voltage variable is introduced to coordinate the balancing of dc-link capacitor voltages and SC voltages. Compared to the balancing method that solely considers the SC voltages, the presented method reduces the dc-link voltage fluctuations without affecting the voltage balance of SCs. Finally, both simulation and experimental results verify the effectiveness of the presented method.
文摘In the context of next-generation optical access networks beyond 10 G, for high SE and flexible dynamic bandwidth allocation (DBA), the scheme of hybrid 64/16/4QAM-OFDM signal for downlink transmission and hybrid 16/8/QPSK-OFDM signal for uplink transmission is successfully proposed and experimentally presented in a full-duplex PON based on OFDM system. Here, for the uplink, in order to unit management of the optical line terminal (OLT) and reduce cost, the optical source functioned as the optical subcarrier at optical network units (ONUs) is from OLT in the central station. Moreover, there is an external cavity laser (ECL) with center frequency of 193.2 THz not only employed as optical modulated signal but also acted as LO signal. Our simulation results show that bit error ratio (BER) under hardware detection forward error correction has been successfully gained after 20 km of SSMF transmission. It is observed that the receiver sensitivity of multilevel PSK (M-PSK) is obviously larger than that of the M-QAM in this measurement scheme.
基金the National Natural Science Foundation of China(No.62175267)the Beijing Municipal Natural Science Foundation(No.4192061)+1 种基金the Fundamental Research Funds for the Central Universities(2020MDJC13)the Beijing Talents Foundation(2018000021223ZK45)for the financial support.
文摘High performance electro-optic modulator,as the key device of integrated ultra-wideband optical systems,have be-come the focus of research.Meanwhile,the organic-based hybrid electro-optic modulators,which make full use of the advant-ages of organic electro-optic(OEO)materials(e.g.high electro-optic coefficient,fast response speed,high bandwidth,easy pro-cessing/integration and low cost)have attracted considerable attention.In this paper,we introduce a series of high-perform-ance OEO materials that exhibit good properties in electro-optic activity and thermal stability.In addition,the recent progress of organic-based hybrid electro-optic devices is reviewed,including photonic crystal-organic hybrid(PCOH),silicon-organic hy-brid(SOH)and plasmonic-organic hybrid(POH)modulators.A high-performance integrated optical platform based on OEO ma-terials is a promising solution for growing high speeds and low power consumption in compact sizes.
基金This work is supported by The National key research and development program of China(2016YFB0100600)the Key Program of Bureau of Frontier Sciences and Education,Chinese Academy of Sciences(QYZDBSSW-JSC044)the National Natural Science Foundation of China(No.51507166).
文摘A compact wirebond packaged phase-leg SiC/Si hybrid module was designed,developed,and tested.Details of the layout and gate drive designs are described.The IC chip for gate drive is carefully selected and compared.Dual pulse test confirmed that,the switching loss of hybrid module is close to pure SiC MOSFET module,and it is much less than pure Si IGBT device.The cost of hybrid module is closer to Si IGBT.
文摘In this paper,the hybrid photovoltaic-thermoelectric generator(PVTEG)combined dynamic voltage restorer(DVR)system is proposed for the power quality disturbances compensation in a single-phase distribution system.The stable and precise level of input voltage is essential for the smooth and trouble-free operation of the electrically sensitive loads which are connected at the utility side to avoid system malfunctions.In this context,the hybrid PV-TEG energy module combined DVR system is proposed in this paper.With the support of the hybrid energy module,the DVR will perform the power quality disturbances compensation effectively with needed voltage and/or power.In the proposed system,the PV and TEG energy sources are connected electrically in series to produce adequate voltage for the DVR operation and the fractional factor-based variable incremental conduction(FFVINC)maximum power point tracking(MPPT)control algorithm is employed to extract the possible maximum power from the PV array.The intelligent fuzzy logic controller(FLC)is chosen for implementing the MPPT control algorithm.The half-bridge voltage source inverter(VSI)circuit and in-phase voltage compensation technique are used in the DVR for better power quality disturbances compensation.The performance and usefulness of the proposed DVR system are investigated by an extensive simulation study with four different modes of operation,the study results are confirmed that the proposed system promptly identifies the power quality disturbances for compensation.Moreover,the investigation proved that the combined PV and TEG energy module can provide better energy efficiency in converting solar irradiation into electricity.
基金Funded by the National Key Basic Research Development Program of China(973 Plan)(No.2013CB632505)the National Natural Science Foundation of China(51477125)the Scientific Research Foundation for the Returned Overseas Chinese Scholars
文摘Hybrid power sources have attracted much attention in the electric vehicle area. Particularly, electric-electric hybrid powertrain system consisting of supercapacitor modules and lithium-ion batteries has been widely applied because of the high power density of supercapacitors. In this study, we design a hybrid powertrain system containing two porous carbon electrode-based supercapacitor modules in parallel and one lithium ion battery pack. With the construction of the testing station, the performance and stability of the used supercapacitor modules are investigated in correlation with the structure of the supercapacitor and the nature of the electrode materials applied. It has been shown that the responding time for voltage vibration from 20 V to 48.5 V during charging or discharging process decreases from about 490 s to 94 s with the increase in applied current from 20 A to 100 A. The capacitance of the capacitor modules is nearly independent on the applied current. With the designed setup, the energy efficiency can reach as high as 0.99. The results described here provide a guidance for material selection of supercapacitors and optimized controlling strategy for hybrid power system applied in electric vehicles.
基金supported by National Natural Science Foundation of China(No.11275038)
文摘A one-dimensional fluid/Monte-Carlo（MC）hybrid model is developed to describe capacitively coupled SiH_4/Ar discharge,in which the lower electrode is applied by a RF source and pulse modulated by a square-wave,to investigate the modulation effects of the pulse duty cycle on the discharge mechanism.An electron Monte Carlo simulation is used to calculate the electron energy distribution as a function of position and time phase.Rate coefficients in chemical reactions can then be obtained and transferred to the fluid model for the calculation of electron temperature and densities of different species,such as electrons,ions,and radicals.The simulation results show that,the electron energy distribution f（ε）is modulated evidently within a pulse cycle,with its tail extending to higher energies during the power-on period,while shrinking back promptly in the afterglow period.Thus,the rate coefficients could be controlled during the discharge,resulting in modulation of the species composition on the substrate compared with continuous excitation.Meanwhile,more negative ions,like Si H_3^-and Si H_2^-,may escape to the electrodes owing to the collapse of ambipolar electric fields,which is beneficial to films deposition.Pulse modulation is thus expected to provide additional methods to customize the plasma densities and components.
文摘In this paper, an improved hybrid space vector pulse width modulation (HSVPWM) technique is proposed for IM (induction motor) drives. The basic principle involved in the proposed random pulse width modulation (RPWM) cuddled SVPWM is amalgamating the pre-calculated switching timings for various sections of hexagonal space vector boundary and the random selection of carrier between two triangular signals, in order to disband acoustic switching noise spectrum with improved fundamental component. The arbitrary selection between triangular carriers, which is decided by digital signal states (Low or High) of the linear feedback shift register (LFSR) based pseudo random binary sequence (PRBS) generator. The SVPWM offers a control degree of freedom in terms of positioning of vectors inside every sampling interval and hence it has six possible variants of the voltage vectors arrangements in each sector. The developed HSVPWM is thoroughly analyzed in using the MATLAB? based simulation for all SVPWM variants. From the simulation and experimental results viz. harmonic spectrum, harmonic spread factor (HSF), total harmonic distortion (THD) etc., and the superiority of the proposed scheme such as better utilization of DC bus and the randomization of the harmonic power are evidenced. For the practical implementation, Xilinx XC3S500E FPGA device has been used.
基金The project supported by the National Natural Science Foundation of China (Nos. 10275068 and 10075049)
文摘Modulation of lower hybrid current drive was used successfully to suppress MHD activity. This was achieved in discharges with MHD m = 2 tearing modes during the discharge conditions Ip = 110 kA, Bt = 1.75 T, ne0 - 1.1 × 1013 cm-3. The delivering time of LHCD pulse is less then 30 μs. The amplitude, interval and the period of LHCD modulation pulse can be adjusted very conveniently. The modulation LHCD can be delivered very fast at any time during the discharge. The modulation LHCD period was always much shorter than the plasma resistive time (Tη ≈100 ms). So the profile of plasma current is changed much faster than the plasma resistive time. The different forms of LHCD modulating can be proved.
基金Supported by the National Key Research and Development Program of China(2016YFB0100600)the Key Program of Bureau of Frontier Sciences and Education,and Chinese Academy of Sciences(QYZDBSSW-JSC044).
文摘SiC Hybrid switch(HyS)combines low conduction loss of Si IGBT and low switching loss of SiC MOSFET,and the cost is closer to that of Si IGBT.The promising high performances of HyS will bring considerable achievement in terms of enhancing power density of a converter system.By reviewing the gate drive pattern,gate drive hardware,current sharing,module design,converter design,and cost,this paper introduces state-of-the-art SiC HyS.
基金supported by the National Natural Science Foundation of China(NSFC)(Nos.61575186,61635001,61727815,and 61625504)
文摘Based on the hybrid integration technology, an ultra-compact and low cost transmitter optical subassembly module is proposed. Four directly modulated lasers are combined with a coarse wavelength division multiplexer operated at the O-band. The bandwidth for all channels is measured to be approximately 3 GHz. The 112 Gb∕s transmission is experimentally demonstrated for a 10 km standard single mode fiber（SSMF）, in which an optical isolator is used for avoiding the back-reflected and scattered light to improve the bit error rate（BER） performance. A low BER and clear eye opening are achieved for 10 km transmission.
基金Supported by the Higher Education Commission (HEC), Pakistan
文摘Multicarrier transmission systems like orthogonal frequency division multiplexing （OFDM） support high data rate and generally require no equalization at the receiver, making them simple and efficient. This paper studies the design and performance analysis of a hybrid modulation system derived from multifrequency and MQAM signals, employed in OFDM. This modulation scheme has better bit error rate （BER） performance and exhibits low PAPR. The proposed hybrid modulator reduces PAPR while keeping the OFDM transceiver design simple, as it does not require any side information or a little side information （only one bit） to be sent and is efficient for arbitrary number of subcarriers. The results of the implementations are compared with those of conventional OFDM system.
基金the Deutsche Forschungsgemeinschaft(DFG,German Research Foundation)under Germany’s Excellence Strategy via the Excellence Cluster 3D Matter Made to Order(EXC-2082/1-390761711)the Collaborative Research Center WavePhenomena(CRC 1173)+4 种基金by the Bundesministerium für Bildung und Forschung(BMBF)via the projects PRIMA(#13N14630),DiFeMiS(#16ES0948)which is part of the programme“Forschungslabore Mikroelektronik Deutschland(ForLab),and Open6GHub(#16KISK010)by the European Research Council(ERC Consolidator Grant‘TeraSHAPE’#773248),by the H2020 Photonic Packaging Pilot Line PIXAPP(#731954)by the Alfried Krupp von Bohlen und Halbach Foundation,and by the Karlsruhe School of Optics and Photonics(KSOP).
文摘Wafer-level mass production of photonic integrated circuits(PIC)has become a technological mainstay in the field of optics and photonics,enabling many novel and disrupting a wide range of existing applications.However,scalable photonic packaging and system assembly still represents a major challenge that often hinders commercial adoption of PIC-based solutions.Specifically,chip-to-chip and fiber-to-chip connections often rely on so-called active alignment techniques,where the coupling efficiency is continuously measured and optimized during the assembly process.This unavoidably leads to technically complex assembly processes and high cost,thereby eliminating most of the inherent scalability advantages of PIC-based solutions.In this paper,we demonstrate that 3D-printed facet-attached microlenses(FaML)can overcome this problem by opening an attractive path towards highly scalable photonic system assembly,relying entirely on passive assembly techniques based on industry-standard machine vision and/or simple mechanical stops.FaML can be printed with high precision to the facets of optical components using multi-photon lithography,thereby offering the possibility to shape the emitted beams by freely designed refractive or reflective surfaces.Specifically,the emitted beams can be collimated to a comparatively large diameter that is independent of the device-specific mode fields,thereby relaxing both axial and lateral alignment tolerances.Moreover,the FaML concept allows to insert discrete optical elements such as optical isolators into the free-space beam paths between PIC facets.We show the viability and the versatility of the scheme in a series of selected experiments of high technical relevance,comprising pluggable fiber-chip interfaces,the combination of PIC with discrete micro-optical elements such as polarization beam splitters,as well as coupling with ultra-low back-reflection based on non-planar beam paths that only comprise tilted optical surfaces.Based on our results,we believe that the FaML concept opens an attractive path towards novel PIC-based system architectures that combine the distinct advantages of different photonic integration platforms.
基金the State Key Laboratoryof Particle Detection and Electronics, SKLPDE-ZZ-202002.
文摘Background HEPS-BPIX is a prototype of photon counting pixel detector developed for the High Energy Photon Source.It consists of 16 silicon pixel modules which should be tested individually to ensure the function and performance.Purpose Due to various factors such as the non-uniformity of the processes and voltage drop,the response of each pixel in the silicon pixel module is not identical completely.The response difference of pixels can be minimized by the threshold calibration.This system is developed for the quality test and calibration of the silicon pixel modules.Methods The system consists of a mother board,a control board and a data acquisition(DAQ)system.The mother board provides necessary resources including power supplies and the fanout of calibration signals.Besides,it can be used to test the connectivity by monitoring the power states.The control board reads data out and provides the clock,trigger and configuration data for the silicon pixel module.The DAQ system sends the control commands and receives the readout data through an Ethernet link.Results Compared with the previous readout system,this designed system has a lower noise level and better scanning curves making the calibration more accurate.And it has been successfully applied to the comparison experiments of the through silicon via and wire-bonding silicon pixel modules.Conclusion The results show that this test system can be used to the quality test and calibration of the silicon pixel modules.In addition,the system can be adapted to the measurement of different pixel array detector modules.
