Pre-existing natural fractures and other structurally weak planes are usually well-developed in unconventional reservoirs.When such fractures intersect with hydraulic induced fractures,they will redirect and propagate...Pre-existing natural fractures and other structurally weak planes are usually well-developed in unconventional reservoirs.When such fractures intersect with hydraulic induced fractures,they will redirect and propagate as an important mechanical principle of volume fracturing by the formation of complex fracture networks.Under the shadow effect of natural fractures and other structurally weak planes with hydraulic supported fracture stress,hydraulic fractures do not fully propagate in the direction of the maximum horizontal-principal-stress.This paper computed the stress intensity factors of hydraulic fracture types I and II by integrating the various interactions,established universally-applicable mechanical principles for the propagation behavior when a hydraulic fracture propagating in an arbitrary direction intersects with a natural fracture at an arbitrary angle,and demonstrated the mechanical principles of the intersection between hydraulic induced fractures and pre-existing natural fractures.This study proved the following conclusions:as the intersection angle between the hydraulic fracture and the maximum horizontal-principal-stress increased,the possibility of the hydraulic fracture being captured by the natural fracture with an identical approaching angle first increased and then decreased;as the net stress increased,the intersection behavior between the hydraulic fracture and the natural fracture transitioned from penetration to capture.展开更多
Considering the danger of water inrush in mining very thick coal seam under water-rich roof in Majialiang Coal Mine,the universal discrete element(UDEC)software was used to simulate the overburden fracture evolution l...Considering the danger of water inrush in mining very thick coal seam under water-rich roof in Majialiang Coal Mine,the universal discrete element(UDEC)software was used to simulate the overburden fracture evolution laws when mining 4#coal seam.Besides,this study researched on the influence of face advancing length,speed and mining height on the height of the water flowing fractured zones(HWFFZ),and analyzed the correlation of face advancing length and change rules of aquifer water levels and goaf water inflow.Based on those mentioned above,this research proposed the following water-controlling technologies:draining the roof water before mining,draining goaf water,reasonable advancing speed and mining thickness.These water-controlling technologies were successfully used in the feld,thus ensured safely mining the very thick coal seam under water-rich roof.展开更多
Since 2000, the French National Radioactive Waste Management Agency （ANDRA） has been constructing an Underground Research Laboratory （URL） at Bure （east of the Paris Basin） to perform experiments in order to obt...Since 2000, the French National Radioactive Waste Management Agency （ANDRA） has been constructing an Underground Research Laboratory （URL） at Bure （east of the Paris Basin） to perform experiments in order to obtain in situ data necessary to demonstrate the feasibility of geological repository in the Callovo- Oxfordian claystone. An important experimental program is planned to characterize the response of the rock to different drift construction methods, Before 2008, at the main level of the laboratory, most of the drifts were excavated using pneumatic hammer and supported with rock bolts, sliding steel arches and fiber shotcrete. Other techniques, such as road header techniques, stiff and flexible supports, have also been used to characterize their impacts. The drift network is developed following the in situ major stresses. The parallel drifts are separated enough so as they can be considered independently when their hydromechanical （HM） behaviors are compared. Mine-by experiments have been performed to measure the HM response of the rock and the mechanical loading applied to the support system due to the digging and after excavation. Drifts exhibit extensional （mode I） and shear fractures （modes II and III） induced by excavation works. The extent of the induced fracture networks depends on the drift orientation versus the in situ stress field. This paper describes the drift convergence and deformation in the surrounding rock walls as function of time and the impact of different support methods on the rock mass behavior. An observation based method is finally applied to distinguish the instantaneous and time-dependent parts of the rock mass deformation around the drifts.展开更多
Crushing and embedment are two critical downhole proppant degradation mechanisms that lead to a significant drop in production outputs in unconventional oil/gas stimulation projects. These persistent production drops ...Crushing and embedment are two critical downhole proppant degradation mechanisms that lead to a significant drop in production outputs in unconventional oil/gas stimulation projects. These persistent production drops due to the non-linear responses of proppants under reservoir conditions put the future utilization of such advanced stimulation techniques in unconventional energy extraction in doubt. The aim of this study is to address these issues by conducting a comprehensive experimental approach. According to the results, whatever the type of proppant, all proppant packs tend to undergo significant plastic deformation under the first loading cycle.Moreover, the utilization of ceramic proppants(which retain proppant pack porosity up to 75%), larger proppant sizes(which retain proppant pack porosity up to 15.2%) and higher proppant concentrations(which retain proppant pack porosity up to 29.5%) in the fracturing stimulations with higher in-situ stresses are recommended to de-escalate the critical consequences of crushing associated issues. Similarly, the selection of resin-coated proppants over ceramic and sand proppants may benefit in terms of obtaining reduced proppant embedment.In addition, selection of smaller proppant sizes and higher proppant concentrations are suggested for stimulation projects at depth with sedimentary formations and lower in-situ stresses where proppant embedment predominates. Furthermore, correlation between proppant embedment with repetitive loading cycles was studied.Importantly, microstructural analysis of the proppant-embedded siltstone rock samples revealed that the initiation of secondary induced fractures. Finally, the findings of this study can greatly contribute to accurately select optimum proppant properties(proppant type, size and concentration) depending on the oil/gas reservoir characteristics to minimize proppant crushing and embedment effects.展开更多
Oil exploration and production,well stability,sand production,geothermal drilling,waste-water or CO_(2) sequestration,geohazards assessment,and EOR processes such as hydraulic fracturing,require adequate information a...Oil exploration and production,well stability,sand production,geothermal drilling,waste-water or CO_(2) sequestration,geohazards assessment,and EOR processes such as hydraulic fracturing,require adequate information about in-situ stresses.There are several methods for analyzing the magnitude and direction of in-situ stresses.The evaluation of tensile fractures and shear fractures in vertical oil and gas wellbores using image logs is one of these methods.Furthermore,when image logs are run in boreholes,they can be extremely costly and possibly stop the drilling.The data for this study were gathered from seven directional wells drilled into a strike-slip fault reservoir in southern Iran.Vertical stress,minimum horizontal stress,pore pressure,Poisson's ratio of formations,and 233 mud loss reporting points make up the entire data.This is the first time maximum horizontal stress direction has been calculated without referring to image log data.In addition,the points of lost circulation were categorized into natural and induced fracture.The results revealed that,the maximum horizontal stress direction of the reservoir was calculated at 65northeast-southwest.The error rate is roughly 10when comparing the results of this investigation to those obtained from the image log.The maximum horizontal stress direction is calculated precisely.In terms of tensile fracture pressure,the in-situ stress ratio identifies the safest as well as the most critical inclination and azimuth for each well.展开更多
基金Sponsored by National Science and Technology Major Projects(2016ZX05052,2016ZX05014).
文摘Pre-existing natural fractures and other structurally weak planes are usually well-developed in unconventional reservoirs.When such fractures intersect with hydraulic induced fractures,they will redirect and propagate as an important mechanical principle of volume fracturing by the formation of complex fracture networks.Under the shadow effect of natural fractures and other structurally weak planes with hydraulic supported fracture stress,hydraulic fractures do not fully propagate in the direction of the maximum horizontal-principal-stress.This paper computed the stress intensity factors of hydraulic fracture types I and II by integrating the various interactions,established universally-applicable mechanical principles for the propagation behavior when a hydraulic fracture propagating in an arbitrary direction intersects with a natural fracture at an arbitrary angle,and demonstrated the mechanical principles of the intersection between hydraulic induced fractures and pre-existing natural fractures.This study proved the following conclusions:as the intersection angle between the hydraulic fracture and the maximum horizontal-principal-stress increased,the possibility of the hydraulic fracture being captured by the natural fracture with an identical approaching angle first increased and then decreased;as the net stress increased,the intersection behavior between the hydraulic fracture and the natural fracture transitioned from penetration to capture.
基金provided by the Priority Academic Program Development of Jiangsu Higher Education Institutions of China(No.SZBF2011-6-B35)the Fundamental Research Funds for the Central Universities of China(No.2012LWB42)
文摘Considering the danger of water inrush in mining very thick coal seam under water-rich roof in Majialiang Coal Mine,the universal discrete element(UDEC)software was used to simulate the overburden fracture evolution laws when mining 4#coal seam.Besides,this study researched on the influence of face advancing length,speed and mining height on the height of the water flowing fractured zones(HWFFZ),and analyzed the correlation of face advancing length and change rules of aquifer water levels and goaf water inflow.Based on those mentioned above,this research proposed the following water-controlling technologies:draining the roof water before mining,draining goaf water,reasonable advancing speed and mining thickness.These water-controlling technologies were successfully used in the feld,thus ensured safely mining the very thick coal seam under water-rich roof.
文摘Since 2000, the French National Radioactive Waste Management Agency （ANDRA） has been constructing an Underground Research Laboratory （URL） at Bure （east of the Paris Basin） to perform experiments in order to obtain in situ data necessary to demonstrate the feasibility of geological repository in the Callovo- Oxfordian claystone. An important experimental program is planned to characterize the response of the rock to different drift construction methods, Before 2008, at the main level of the laboratory, most of the drifts were excavated using pneumatic hammer and supported with rock bolts, sliding steel arches and fiber shotcrete. Other techniques, such as road header techniques, stiff and flexible supports, have also been used to characterize their impacts. The drift network is developed following the in situ major stresses. The parallel drifts are separated enough so as they can be considered independently when their hydromechanical （HM） behaviors are compared. Mine-by experiments have been performed to measure the HM response of the rock and the mechanical loading applied to the support system due to the digging and after excavation. Drifts exhibit extensional （mode I） and shear fractures （modes II and III） induced by excavation works. The extent of the induced fracture networks depends on the drift orientation versus the in situ stress field. This paper describes the drift convergence and deformation in the surrounding rock walls as function of time and the impact of different support methods on the rock mass behavior. An observation based method is finally applied to distinguish the instantaneous and time-dependent parts of the rock mass deformation around the drifts.
文摘Crushing and embedment are two critical downhole proppant degradation mechanisms that lead to a significant drop in production outputs in unconventional oil/gas stimulation projects. These persistent production drops due to the non-linear responses of proppants under reservoir conditions put the future utilization of such advanced stimulation techniques in unconventional energy extraction in doubt. The aim of this study is to address these issues by conducting a comprehensive experimental approach. According to the results, whatever the type of proppant, all proppant packs tend to undergo significant plastic deformation under the first loading cycle.Moreover, the utilization of ceramic proppants(which retain proppant pack porosity up to 75%), larger proppant sizes(which retain proppant pack porosity up to 15.2%) and higher proppant concentrations(which retain proppant pack porosity up to 29.5%) in the fracturing stimulations with higher in-situ stresses are recommended to de-escalate the critical consequences of crushing associated issues. Similarly, the selection of resin-coated proppants over ceramic and sand proppants may benefit in terms of obtaining reduced proppant embedment.In addition, selection of smaller proppant sizes and higher proppant concentrations are suggested for stimulation projects at depth with sedimentary formations and lower in-situ stresses where proppant embedment predominates. Furthermore, correlation between proppant embedment with repetitive loading cycles was studied.Importantly, microstructural analysis of the proppant-embedded siltstone rock samples revealed that the initiation of secondary induced fractures. Finally, the findings of this study can greatly contribute to accurately select optimum proppant properties(proppant type, size and concentration) depending on the oil/gas reservoir characteristics to minimize proppant crushing and embedment effects.
文摘Oil exploration and production,well stability,sand production,geothermal drilling,waste-water or CO_(2) sequestration,geohazards assessment,and EOR processes such as hydraulic fracturing,require adequate information about in-situ stresses.There are several methods for analyzing the magnitude and direction of in-situ stresses.The evaluation of tensile fractures and shear fractures in vertical oil and gas wellbores using image logs is one of these methods.Furthermore,when image logs are run in boreholes,they can be extremely costly and possibly stop the drilling.The data for this study were gathered from seven directional wells drilled into a strike-slip fault reservoir in southern Iran.Vertical stress,minimum horizontal stress,pore pressure,Poisson's ratio of formations,and 233 mud loss reporting points make up the entire data.This is the first time maximum horizontal stress direction has been calculated without referring to image log data.In addition,the points of lost circulation were categorized into natural and induced fracture.The results revealed that,the maximum horizontal stress direction of the reservoir was calculated at 65northeast-southwest.The error rate is roughly 10when comparing the results of this investigation to those obtained from the image log.The maximum horizontal stress direction is calculated precisely.In terms of tensile fracture pressure,the in-situ stress ratio identifies the safest as well as the most critical inclination and azimuth for each well.
