The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian componen...The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian component.To obtain higher accuracy and resolution of ocean gravity information,researchers have proposed a novel altimeter called the wide-swath altimeter.This altimeter allows for the simultaneous acquisition of high-precision and high-resolution two-dimensional measurements of sea surface height(SSH).In this paper,the Surface Water and Ocean Topography(SWOT)mission with a wide-swath altimeter on board is selected for research.One cycle of swoT sea surface height data is simulated to inverse the DOV in the Arabian Sea(45°E—80°E,0°-30°N),and the inversion results are compared with those of conventional altimeter data.The results demonstrate that the difference between the meridian and prime components derived from the inversion of swoT wide-swath data is minimal,significantly outperforming the inversion results of conventional nadir altimeter data.The advantage of swoT wide-swath altimeter lies in its ability to use the multi-directional geoid slope at any sea surface measurement point to invert the components in the meridian and prime directions.To investigate the impact of this advantage on inversion precision,this paper employs a method to calculate the gradient of the geoid in multiple directions to invert DoV components.The improvement effect of calculating the gradient of the geoid in multiple directions on the precision of DoV component is analyzed.It is found that the accuracy of DoV inversion has significantly improved with the increase of geodetic gradient calculation direction.In addition,the effects of various errors and grid spacing in SwoT wide sea surface height data on the precision of Dov inversion are also analyzed.展开更多
Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, th...Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, the inversion accuracy of the traditional singular value decomposition （SVD） inversion method reduces with a decrease of SNR. In order to enhance the inversion accuracy and improve robustness of the inversion method to the SNR, an improved inversion method, based on damping factor and spectrum component residual correction, is proposed in this study. The numerical inversion results show that the oscillation of the RTS derived from the SVD method increased with a decrease of SNR, which makes it impossible to get accurate inversion components. However, the SNR has little influence on inversion components of the improved method, and the RTS has high inversion accuracy and robustness. Moreover, RTS derived from core sample data is basically in accord with the pore-size distribution curve, and the RTS derived from the actual induced polarization logging data is smooth and continuous, which indicates that the improved method is practicable.展开更多
A data-space inversion(DSI)method has been recently proposed and successfully applied to the history matching and production prediction of reservoirs.Based on Bayesian theory,DSI can directly and effectively obtain go...A data-space inversion(DSI)method has been recently proposed and successfully applied to the history matching and production prediction of reservoirs.Based on Bayesian theory,DSI can directly and effectively obtain good posterior flow predictions without inversion of geological parameters of reservoir model.This paper presents an improved DSI method to fast predict reservoir state fields(e.g.saturation and pressure profiles)via observed production data.Firstly,a large number of production curves and state data are generated by reservoir model simulation to expand the data space of original DSI.Then,efficient history matching only on the observed production data is carried out via the original DSI to obtain related parameters which reflects the weight of the real reservoir model relative to prior reservoir models.Finally,those parameters are used to predict the oil saturation and pressure profiles of the real reservoir model by combining large amounts of state data of prior reservoir models.Two examples including conventional heterogeneous and unconventional fractured reservoir are implemented to test the performances of predicting saturation and pressure profiles of this improved DSI method.Besides,this method is also tested in a real field and the obtained results show the high computational efficiency and high accuracy of the practical application of this method.展开更多
D-T_(2)two-dimensional nuclear magnetic resonance(2D NMR)logging technology can distinguish pore fluid types intuitively,and it is widely used in oil and gas exploration.Many 2D NMR inversion methods(e.g.,truncated si...D-T_(2)two-dimensional nuclear magnetic resonance(2D NMR)logging technology can distinguish pore fluid types intuitively,and it is widely used in oil and gas exploration.Many 2D NMR inversion methods(e.g.,truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization methods)have been proposed successively,but most are limited to numerical simulations.This study focused on the applicability of different inversion methods for NMR logging data of various acquisition sequences,from which the optimal inversion method was selected based on the comparative analysis.First,the two-dimensional NMR logging principle was studied.Then,these inversion methods were studied in detail,and the precision and computational efficiency of CPMG and diffusion editing(DE)sequences obtained from oil-water and gas-water models were compared,respectively.The inversion results and calculation time of truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization were compared and analyzed through numerical simulations.The inversion method was optimized to process SP mode logging data from the MR Scanner instrument.The results showed that the TIST-regularization and LM-norm smoothing methods were more accurate for the CPMG and DE sequence echo trains of the oil-water and gas-water models.However,the LM-norm smoothing method was less time-consuming,making it more suitable for logging data processing.A case study in well A25 showed that the processing results by the LM-norm smoothing method were consistent with GEOLOG software.This demonstrates that the LM-norm smoothing method is applicable in practical NMR logging processing.展开更多
The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential,...The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential, the transport properties of CO2-N2 mixture are presented in a temperature range front 273.15 K to 3273.15 K at low density by employing the Chapman-Enskog scheme and the Wang Chang-Uhlenbeck de Boer theory, consisting of a viscosity coefficient, a thermal conductivity coefficient, a binary diffusion coefficient, and a thermal diffusion factor. The accuracy of the predicted results is estimated to be 2% for viscosity, 5% for thermal conductivity, and 10% for binary diffusion coefficient.展开更多
The magnetic interface forward and inversion method is realized using the Taylor series expansion to linearize the Fourier transform of the exponential function. With a large expansion step and unbounded neighborhood,...The magnetic interface forward and inversion method is realized using the Taylor series expansion to linearize the Fourier transform of the exponential function. With a large expansion step and unbounded neighborhood, the Taylor series is not convergent, and therefore, this paper presents the magnetic interface forward and inversion method based on Pade approximation instead of the Taylor series expansion. Compared with the Taylor series, Pade＇s expansion＇s convergence is more stable and its approximation more accurate. Model tests show the validity of the magnetic forward modeling and inversion of Pade approximation proposed in the paper, and when this inversion method is applied to the measured data of the Matagami area in Canada, a stable and reasonable distribution of underground interface is obtained.展开更多
The accurate reduced potential energies for two binary gas mixtures including benzene- methanol and methane-tetrafluoromethane at low density have been obtained by direct inversion of the viscosity collision integral ...The accurate reduced potential energies for two binary gas mixtures including benzene- methanol and methane-tetrafluoromethane at low density have been obtained by direct inversion of the viscosity collision integral equations. The kinetic theory along with the extended principle of corresponding-states has been used to calculate the viscosity and dif- fusion coefficients over a wide range of temperature and composition. Good agreements between calculated and experimental data are obtained.展开更多
In gravity gradient inversion,to choose an appropriate component combination is very important,that needs to understand the function of each component of gravity gradient in the inversion.In this paper,based on the pr...In gravity gradient inversion,to choose an appropriate component combination is very important,that needs to understand the function of each component of gravity gradient in the inversion.In this paper,based on the previous research on the characteristics of gravity gradient components,we propose a reweighted inversion method to evaluate the influence of single gravity gradient component on the inversion resolution The proposed method only adopts the misfit function of the regularized equation and introduce a depth weighting function to overcome skin effect produced in gravity gradient inversion.A comparison between different inversion results was undertaken to verify the influence of the depth weighting function on the inversion result resolution.To avoid the premise of introducing prior information,we select the depth weighting function based on the sensitivity matrix.The inversion results using the single-prism model and the complex model show that the influence of different components on the resolution of inversion results is different in different directions,however,the inversion results based on two kind of models with adding different levels of random noise are basically consistent with the results of inversion without noises.Finally,the method was applied to real data from the Vinton salt dome,Louisiana,USA.展开更多
The large-scale convergence of homotopy parametric inversion method on the water quality model parameters calculated was used,with application in parametric inversion calculation of total phosphorus of Beijing Miyun R...The large-scale convergence of homotopy parametric inversion method on the water quality model parameters calculated was used,with application in parametric inversion calculation of total phosphorus of Beijing Miyun Reservoir.Through calculated and compared the error of sedimentation rate by homotopy parametric inversion method and genetic inversion calculation method,the results indicate that homotopy parametric inversion method has good stability,calculating speed,and even if the initial selection away from the objective function,the solution still has a good convergence.展开更多
Generalized Inversion Method has been used to estimate the spatial variation of site effects,using the digital data of SH-waves recorded by 63 stations in the Capital Circle Region of China from 2001 to 2006.We gained...Generalized Inversion Method has been used to estimate the spatial variation of site effects,using the digital data of SH-waves recorded by 63 stations in the Capital Circle Region of China from 2001 to 2006.We gained the site effects of all stations participating in the calculation.We found that the site effect of rock was stabile and about 1.0 from 1.0Hz to 10.0Hz,while the site effect of deposit was high in low frequencies,about 3 ～ 7 from 1.0Hz to 8.0Hz,and the site effect was protuberant at about 5.0Hz,then fell as the frequency increased.The result shows the shape and intensity of station site effects are mainly influenced by the lithology below the station,and possibly also by the local geological structure.展开更多
This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire pattern...This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire patterns indicate that the copper interconnects are a series of curves with continuous variations instead of beelines. The control equation set of the copper interconnects central lines is attained through the Moire inversion method. This work can be extended to inspect the structural defects and provide a reliable support for the interconnects structure fabrication.展开更多
Elastic impedance inversion with high efficiency and high stability has become one of the main directions of seismic pre-stack inversion. The nonlinear elastic impedance inversion method based on a fast Markov chain M...Elastic impedance inversion with high efficiency and high stability has become one of the main directions of seismic pre-stack inversion. The nonlinear elastic impedance inversion method based on a fast Markov chain Monte Carlo （MCMC） method is proposed in this paper, combining conventional MCMC method based on global optimization with a preconditioned conjugate gradient （PCG） algorithm based on local optimization, so this method does not depend strongly on the initial model. It converges to the global optimum quickly and efficiently on the condition that effi- ciency and stability of inversion are both taken into consid- eration at the same time. The test data verify the feasibility and robustness of the method, and based on this method, we extract the effective pore-fluid bulk modulus, which is applied to reservoir fluid identification and detection, and consequently, a better result has been achieved.展开更多
Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea...Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea surface phenomena.SAR systems,for instance,are hindered by an azimuth cut-off phenomenon in sea surface wind field observation.Wave spectrometers,while unaffected by the azimuth cutoff phenomenon,struggle with low azimuth resolution,impacting the capture of detailed wave and wind field data.This study utilizes SAR and surface wave investigation and monitoring(SWIM)data to initially extract key feature parameters,which are then prioritized using the extreme gradient boosting(XGBoost)algorithm.The research further addresses feature collinearity through a combined analysis of feature importance and correlation,leading to the development of an inversion model for wave and wind parameters based on XGBoost.A comparative analysis of this model with ERA5 reanalysis and buoy data for of significant wave height,mean wave period,wind direction,and wind speed reveals root mean square errors of 0.212 m,0.525 s,27.446°,and 1.092 m/s,compared to 0.314 m,0.888 s,27.698°,and 1.315 m/s from buoy data,respectively.These results demonstrate the model’s effective retrieval of wave and wind parameters.Finally,the model,incorporating altimeter and scatterometer data,is evaluated against SAR/SWIM single and dual payload inversion methods across different wind speeds.This comparison highlights the model’s superior inversion accuracy over other methods.展开更多
The ^(12)C+^(12)C fusion is one of the most important reactions in modern nuclear astrophysics.The trend and magnitude of the reaction rate within the Gamow window strongly influence various astrophysical processes.Ho...The ^(12)C+^(12)C fusion is one of the most important reactions in modern nuclear astrophysics.The trend and magnitude of the reaction rate within the Gamow window strongly influence various astrophysical processes.However,direct measurement of this reaction is extremely difficult,which makes it necessary to develop indirect methods.In this study,the ^(23)Na+p reaction system was used to study the compound nucleus ^(24)Mg.We employed a thick-target inverse kinematics method combined with theγ-charged-particle coincidence technique to measure the proton andα exit channels of ^(24)Mg.Technical details of the ^(23)Na+p thick-target inverse kinematics experiment and analysis are presented herein.展开更多
This study presents a novel two-step approach to assess plate-like structural laminar damages,particularly for delamination damage detection of composite structures.Firstly,a 2-D continuous wavelet transform is employ...This study presents a novel two-step approach to assess plate-like structural laminar damages,particularly for delamination damage detection of composite structures.Firstly,a 2-D continuous wavelet transform is employed to identify the damage location and sizes from vibration curvature data.An inverse method is subsequently then used to determine the bending stiffness reduction ratio along a specified direction,enabling the quantification of the delamination severity.The method employed in this study is an extension of the one-dimensional inverse method developed in a previous work of the authors.The applicability of the two-step inverse approach is demonstrated in a simulation analysis and by an experimental study on a cantilever composite plate containing a single delamination.The inverse method is shown to have the capacity to reveal the detailed damage information of delamination within a constrained searching space and can be used to determine the effective flexural stiffness of composite plate structures,even in cases of complex delamination damage.展开更多
The remote measurement of the vertical distribution of acoustical parameters of the sea bottom is an inverse method in acoustics. The existing methods can be divided into two types: the wave method and the ray method....The remote measurement of the vertical distribution of acoustical parameters of the sea bottom is an inverse method in acoustics. The existing methods can be divided into two types: the wave method and the ray method. The former usually does not apply to cases with discontinuity in acoustical parameter profiles[1] , whereas the latter usually ignores the contributions made by multiple reflections, resulting in the appearance of pseudo interfaces. However, under certain practical circumstances, the ray method can produce satisfactory results[2,3]. In this paper, at first we use the conception of equitime layer thickness to obtain the pulse response iteration method. The anti-interference capability of this method is poor. In order to improve this capability, we develope the sample iteration method and the sample-averaging iteration method. The sample-averaging iteration method introduces a way of statistical averaging, which can further improve the anti-interference capability.展开更多
A method for the inversion of the transmission losses for the bottom reflection loss is proposed on the basis of the theory of the smooth- averaged sound field. The procedure of the inversion is based on the criterion...A method for the inversion of the transmission losses for the bottom reflection loss is proposed on the basis of the theory of the smooth- averaged sound field. The procedure of the inversion is based on the criterion of the least square error in the transmission losses between calculation and measurement. By using the Gauss - Newton iterative approach, the non - linear least square aloqrithm is equivalent to solving a sequence of lineared least square problems. The physical causes of the instability of the inversion problem are discussed and the stability is improved by means of the Levenberg- Marquardt method. Both numerical simulations with noise and experimental results show that the inversion for the bottom reflection loss of small grazing angle has high precision and the certain perturbation in the measured transmission losses does not lead to serious deviation in the inversion result of the bottom reflection loss.展开更多
Genetic algorithm finite element method (GA FEM) is applied to the study of tectonic stress field of part of East Asia area. From the observed stress distribution, 2 D elastic plane stress inversion is made to dedu...Genetic algorithm finite element method (GA FEM) is applied to the study of tectonic stress field of part of East Asia area. From the observed stress distribution, 2 D elastic plane stress inversion is made to deduce the boundary forces and investigate controlling factors. It is suggested that the continent continent collision is the dominant factor controlling the Chinese tectonic stress field. The ocean continent convergence along the subduction zone is an important factor. There exists tensile boundary force along the marginal sea.展开更多
The traditional automotive catalytic converter using commercial ceramic honeycomb carriers has many problems such as high back pressure,low engine efficiency,and high usage of precious metals.This study proposes a fou...The traditional automotive catalytic converter using commercial ceramic honeycomb carriers has many problems such as high back pressure,low engine efficiency,and high usage of precious metals.This study proposes a four-channel catalytic micro-reactor based on alumina hollow fiber membrane,which uses phase inversion method for structural molding and regulation.Due to the advantages of its carrier,it can achieve lower ignition temperature under low noble metal loading.With Pd/CeO_(2) at a loading rate of 2.3%(mass),the result showed that the reaction ignition temperature is even less than 160℃,which is more than 90℃ lower than the data of commercial ceramic substrates under similar catalyst loading and airspeed conditions.The technology in turn significantly reduces the energy consumption of the reaction.And stability tests were conducted under constant conditions for 1000 h,which proved that this catalytic converter has high catalytic efficiency and stability,providing prospects for the design of innovative catalytic converters in the future.展开更多
In this work,a sponge-like polysulfonamide(PSA)/SiO_2 composite membrane is unprecedentedly prepared by the phase inversion method,and successfully demonstrated as a novel separator of lithium-ion batteries(LIBs).Comp...In this work,a sponge-like polysulfonamide(PSA)/SiO_2 composite membrane is unprecedentedly prepared by the phase inversion method,and successfully demonstrated as a novel separator of lithium-ion batteries(LIBs).Compared to the commercial polypropylene(PP) separator,the sponge-like PSA/SiO_2 composite possesses better physical and electrochemical properties,such as higher porosity,ionic conductivity,thermal stability and flame retarding ability.The LiCoO_2/Li half-cells using the sponge-like composite separator demonstrate superior rate capability and cyclability over those using the commercial PP separator.Moreover,the sponge-like composite separator can ensure the normal operation of LiCoO_2/Li half-cell at an extremely high temperature of 90 °C,while the commercial PP separator cannot.All these encouraging results suggest that this phase inversion based sponge-like PSA/SiO_2 composite separator is really a promising separator for high performance LIBs.展开更多
基金support from the National Natural Science Foundation of China(No.42274006,42192535,42242015).
文摘The deflection of the vertical(DOV)is the key information in the study of ocean gravity field.However,in most areas,the precision of the prime component of DoV is significantly lower than that of the meridian component.To obtain higher accuracy and resolution of ocean gravity information,researchers have proposed a novel altimeter called the wide-swath altimeter.This altimeter allows for the simultaneous acquisition of high-precision and high-resolution two-dimensional measurements of sea surface height(SSH).In this paper,the Surface Water and Ocean Topography(SWOT)mission with a wide-swath altimeter on board is selected for research.One cycle of swoT sea surface height data is simulated to inverse the DOV in the Arabian Sea(45°E—80°E,0°-30°N),and the inversion results are compared with those of conventional altimeter data.The results demonstrate that the difference between the meridian and prime components derived from the inversion of swoT wide-swath data is minimal,significantly outperforming the inversion results of conventional nadir altimeter data.The advantage of swoT wide-swath altimeter lies in its ability to use the multi-directional geoid slope at any sea surface measurement point to invert the components in the meridian and prime directions.To investigate the impact of this advantage on inversion precision,this paper employs a method to calculate the gradient of the geoid in multiple directions to invert DoV components.The improvement effect of calculating the gradient of the geoid in multiple directions on the precision of DoV component is analyzed.It is found that the accuracy of DoV inversion has significantly improved with the increase of geodetic gradient calculation direction.In addition,the effects of various errors and grid spacing in SwoT wide sea surface height data on the precision of Dov inversion are also analyzed.
基金supported by a project from the Youth Science Foundation of the National Natural Science Foundation of China (11104089)
文摘Relaxation time spectra （RTS） derived from time domain induced polarization data （TDIP） are helpful to assess oil reservoir pore structures. However, due to the sensitivity to the signal-to-noise ratio （SNR）, the inversion accuracy of the traditional singular value decomposition （SVD） inversion method reduces with a decrease of SNR. In order to enhance the inversion accuracy and improve robustness of the inversion method to the SNR, an improved inversion method, based on damping factor and spectrum component residual correction, is proposed in this study. The numerical inversion results show that the oscillation of the RTS derived from the SVD method increased with a decrease of SNR, which makes it impossible to get accurate inversion components. However, the SNR has little influence on inversion components of the improved method, and the RTS has high inversion accuracy and robustness. Moreover, RTS derived from core sample data is basically in accord with the pore-size distribution curve, and the RTS derived from the actual induced polarization logging data is smooth and continuous, which indicates that the improved method is practicable.
基金supported by Southern Marine Science and Engineering Guangdong Laboratory(Zhanjiang)(No.ZJW-2019-04)Cooperative Innovation Center of Unconventional Oil and Gas(Ministry of Education&Hubei Province),Yangtze University(No.UOG2020-17)the National Natural Science Foundation of China(No.51874044,51922007)。
文摘A data-space inversion(DSI)method has been recently proposed and successfully applied to the history matching and production prediction of reservoirs.Based on Bayesian theory,DSI can directly and effectively obtain good posterior flow predictions without inversion of geological parameters of reservoir model.This paper presents an improved DSI method to fast predict reservoir state fields(e.g.saturation and pressure profiles)via observed production data.Firstly,a large number of production curves and state data are generated by reservoir model simulation to expand the data space of original DSI.Then,efficient history matching only on the observed production data is carried out via the original DSI to obtain related parameters which reflects the weight of the real reservoir model relative to prior reservoir models.Finally,those parameters are used to predict the oil saturation and pressure profiles of the real reservoir model by combining large amounts of state data of prior reservoir models.Two examples including conventional heterogeneous and unconventional fractured reservoir are implemented to test the performances of predicting saturation and pressure profiles of this improved DSI method.Besides,this method is also tested in a real field and the obtained results show the high computational efficiency and high accuracy of the practical application of this method.
基金sponsored by the National Natural Science Foundation of China(Nos.42174149,41774144)the National Major Projects(No.2016ZX05014-001).
文摘D-T_(2)two-dimensional nuclear magnetic resonance(2D NMR)logging technology can distinguish pore fluid types intuitively,and it is widely used in oil and gas exploration.Many 2D NMR inversion methods(e.g.,truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization methods)have been proposed successively,but most are limited to numerical simulations.This study focused on the applicability of different inversion methods for NMR logging data of various acquisition sequences,from which the optimal inversion method was selected based on the comparative analysis.First,the two-dimensional NMR logging principle was studied.Then,these inversion methods were studied in detail,and the precision and computational efficiency of CPMG and diffusion editing(DE)sequences obtained from oil-water and gas-water models were compared,respectively.The inversion results and calculation time of truncated singular value decomposition(TSVD),Butler-Reds-Dawson(BRD),LM-norm smoothing,and TIST-L1 regularization were compared and analyzed through numerical simulations.The inversion method was optimized to process SP mode logging data from the MR Scanner instrument.The results showed that the TIST-regularization and LM-norm smoothing methods were more accurate for the CPMG and DE sequence echo trains of the oil-water and gas-water models.However,the LM-norm smoothing method was less time-consuming,making it more suitable for logging data processing.A case study in well A25 showed that the processing results by the LM-norm smoothing method were consistent with GEOLOG software.This demonstrates that the LM-norm smoothing method is applicable in practical NMR logging processing.
基金supported by the National Natural Science Foundation of China (Grant No. 51006083)the China Postdoctoral Science Foundation (Grant No. 20110491658)the Fundamental Research Funds for the Central Universities
文摘The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential, the transport properties of CO2-N2 mixture are presented in a temperature range front 273.15 K to 3273.15 K at low density by employing the Chapman-Enskog scheme and the Wang Chang-Uhlenbeck de Boer theory, consisting of a viscosity coefficient, a thermal conductivity coefficient, a binary diffusion coefficient, and a thermal diffusion factor. The accuracy of the predicted results is estimated to be 2% for viscosity, 5% for thermal conductivity, and 10% for binary diffusion coefficient.
基金supported by Sino Probe-09-01-Integrated geophysical data processing and integrated system for moving platform(No.201311192)Graduate innovation fund of Jilin University(No.2015025)
文摘The magnetic interface forward and inversion method is realized using the Taylor series expansion to linearize the Fourier transform of the exponential function. With a large expansion step and unbounded neighborhood, the Taylor series is not convergent, and therefore, this paper presents the magnetic interface forward and inversion method based on Pade approximation instead of the Taylor series expansion. Compared with the Taylor series, Pade＇s expansion＇s convergence is more stable and its approximation more accurate. Model tests show the validity of the magnetic forward modeling and inversion of Pade approximation proposed in the paper, and when this inversion method is applied to the measured data of the Matagami area in Canada, a stable and reasonable distribution of underground interface is obtained.
文摘The accurate reduced potential energies for two binary gas mixtures including benzene- methanol and methane-tetrafluoromethane at low density have been obtained by direct inversion of the viscosity collision integral equations. The kinetic theory along with the extended principle of corresponding-states has been used to calculate the viscosity and dif- fusion coefficients over a wide range of temperature and composition. Good agreements between calculated and experimental data are obtained.
基金supported by the National Key R&D Program of China(Nos.2016YFC0303002 and 2017YFC0601701)China Geological Survey Program(No.DD20191007)
文摘In gravity gradient inversion,to choose an appropriate component combination is very important,that needs to understand the function of each component of gravity gradient in the inversion.In this paper,based on the previous research on the characteristics of gravity gradient components,we propose a reweighted inversion method to evaluate the influence of single gravity gradient component on the inversion resolution The proposed method only adopts the misfit function of the regularized equation and introduce a depth weighting function to overcome skin effect produced in gravity gradient inversion.A comparison between different inversion results was undertaken to verify the influence of the depth weighting function on the inversion result resolution.To avoid the premise of introducing prior information,we select the depth weighting function based on the sensitivity matrix.The inversion results using the single-prism model and the complex model show that the influence of different components on the resolution of inversion results is different in different directions,however,the inversion results based on two kind of models with adding different levels of random noise are basically consistent with the results of inversion without noises.Finally,the method was applied to real data from the Vinton salt dome,Louisiana,USA.
文摘The large-scale convergence of homotopy parametric inversion method on the water quality model parameters calculated was used,with application in parametric inversion calculation of total phosphorus of Beijing Miyun Reservoir.Through calculated and compared the error of sedimentation rate by homotopy parametric inversion method and genetic inversion calculation method,the results indicate that homotopy parametric inversion method has good stability,calculating speed,and even if the initial selection away from the objective function,the solution still has a good convergence.
基金sponsored by the Special Foundation of China Earthquake Administration (2007-8-26)
文摘Generalized Inversion Method has been used to estimate the spatial variation of site effects,using the digital data of SH-waves recorded by 63 stations in the Capital Circle Region of China from 2001 to 2006.We gained the site effects of all stations participating in the calculation.We found that the site effect of rock was stabile and about 1.0 from 1.0Hz to 10.0Hz,while the site effect of deposit was high in low frequencies,about 3 ～ 7 from 1.0Hz to 8.0Hz,and the site effect was protuberant at about 5.0Hz,then fell as the frequency increased.The result shows the shape and intensity of station site effects are mainly influenced by the lithology below the station,and possibly also by the local geological structure.
基金supported by the JSPS Postdoctoral Fellowship for Foreign Researchersthe National Basic Research Program of China ("973" Project) (2010CB631005,2011CB606105)+1 种基金the National Natural Science Foundation of China (11172151,90916010)Specialized Research Fund for the Doctoral Program of Higher Education(20090002110048)
文摘This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire patterns indicate that the copper interconnects are a series of curves with continuous variations instead of beelines. The control equation set of the copper interconnects central lines is attained through the Moire inversion method. This work can be extended to inspect the structural defects and provide a reliable support for the interconnects structure fabrication.
基金the sponsorship of the National Basic Research Program of China (973 Program,2013CB228604,2014CB239201)the National Oil and Gas Major Projects of China (2011ZX05014-001-010HZ,2011ZX05014-001-006-XY570) for their funding of this research
文摘Elastic impedance inversion with high efficiency and high stability has become one of the main directions of seismic pre-stack inversion. The nonlinear elastic impedance inversion method based on a fast Markov chain Monte Carlo （MCMC） method is proposed in this paper, combining conventional MCMC method based on global optimization with a preconditioned conjugate gradient （PCG） algorithm based on local optimization, so this method does not depend strongly on the initial model. It converges to the global optimum quickly and efficiently on the condition that effi- ciency and stability of inversion are both taken into consid- eration at the same time. The test data verify the feasibility and robustness of the method, and based on this method, we extract the effective pore-fluid bulk modulus, which is applied to reservoir fluid identification and detection, and consequently, a better result has been achieved.
基金The project supported by Key Laboratory of Space Ocean Remote Sensing and Application,Ministry of Natural Resources under contract No.2023CFO016the National Natural Science Foundation of China under contract No.61931025+1 种基金the Innovation Fund Project for Graduate Student of China University of Petroleum(East China)the Fundamental Research Funds for the Central Universities under contract No.23CX04042A.
文摘Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea surface phenomena.SAR systems,for instance,are hindered by an azimuth cut-off phenomenon in sea surface wind field observation.Wave spectrometers,while unaffected by the azimuth cutoff phenomenon,struggle with low azimuth resolution,impacting the capture of detailed wave and wind field data.This study utilizes SAR and surface wave investigation and monitoring(SWIM)data to initially extract key feature parameters,which are then prioritized using the extreme gradient boosting(XGBoost)algorithm.The research further addresses feature collinearity through a combined analysis of feature importance and correlation,leading to the development of an inversion model for wave and wind parameters based on XGBoost.A comparative analysis of this model with ERA5 reanalysis and buoy data for of significant wave height,mean wave period,wind direction,and wind speed reveals root mean square errors of 0.212 m,0.525 s,27.446°,and 1.092 m/s,compared to 0.314 m,0.888 s,27.698°,and 1.315 m/s from buoy data,respectively.These results demonstrate the model’s effective retrieval of wave and wind parameters.Finally,the model,incorporating altimeter and scatterometer data,is evaluated against SAR/SWIM single and dual payload inversion methods across different wind speeds.This comparison highlights the model’s superior inversion accuracy over other methods.
基金supported by the National Key Research and Development Project (No. 2022YFA1602301)the National Natural Science Foundation of China (Nos. U2267205, 12275361, 12125509, 12222514, 11961141003, and 12005304)+2 种基金the CAST Young Talent Support Planthe CNNC Science Fund for Talented Young Scholarsthe Continuous-Support Basic Scientific Research Project
文摘The ^(12)C+^(12)C fusion is one of the most important reactions in modern nuclear astrophysics.The trend and magnitude of the reaction rate within the Gamow window strongly influence various astrophysical processes.However,direct measurement of this reaction is extremely difficult,which makes it necessary to develop indirect methods.In this study,the ^(23)Na+p reaction system was used to study the compound nucleus ^(24)Mg.We employed a thick-target inverse kinematics method combined with theγ-charged-particle coincidence technique to measure the proton andα exit channels of ^(24)Mg.Technical details of the ^(23)Na+p thick-target inverse kinematics experiment and analysis are presented herein.
文摘This study presents a novel two-step approach to assess plate-like structural laminar damages,particularly for delamination damage detection of composite structures.Firstly,a 2-D continuous wavelet transform is employed to identify the damage location and sizes from vibration curvature data.An inverse method is subsequently then used to determine the bending stiffness reduction ratio along a specified direction,enabling the quantification of the delamination severity.The method employed in this study is an extension of the one-dimensional inverse method developed in a previous work of the authors.The applicability of the two-step inverse approach is demonstrated in a simulation analysis and by an experimental study on a cantilever composite plate containing a single delamination.The inverse method is shown to have the capacity to reveal the detailed damage information of delamination within a constrained searching space and can be used to determine the effective flexural stiffness of composite plate structures,even in cases of complex delamination damage.
文摘The remote measurement of the vertical distribution of acoustical parameters of the sea bottom is an inverse method in acoustics. The existing methods can be divided into two types: the wave method and the ray method. The former usually does not apply to cases with discontinuity in acoustical parameter profiles[1] , whereas the latter usually ignores the contributions made by multiple reflections, resulting in the appearance of pseudo interfaces. However, under certain practical circumstances, the ray method can produce satisfactory results[2,3]. In this paper, at first we use the conception of equitime layer thickness to obtain the pulse response iteration method. The anti-interference capability of this method is poor. In order to improve this capability, we develope the sample iteration method and the sample-averaging iteration method. The sample-averaging iteration method introduces a way of statistical averaging, which can further improve the anti-interference capability.
基金The Project Supported by National Natural Science Fundation of China
文摘A method for the inversion of the transmission losses for the bottom reflection loss is proposed on the basis of the theory of the smooth- averaged sound field. The procedure of the inversion is based on the criterion of the least square error in the transmission losses between calculation and measurement. By using the Gauss - Newton iterative approach, the non - linear least square aloqrithm is equivalent to solving a sequence of lineared least square problems. The physical causes of the instability of the inversion problem are discussed and the stability is improved by means of the Levenberg- Marquardt method. Both numerical simulations with noise and experimental results show that the inversion for the bottom reflection loss of small grazing angle has high precision and the certain perturbation in the measured transmission losses does not lead to serious deviation in the inversion result of the bottom reflection loss.
文摘Genetic algorithm finite element method (GA FEM) is applied to the study of tectonic stress field of part of East Asia area. From the observed stress distribution, 2 D elastic plane stress inversion is made to deduce the boundary forces and investigate controlling factors. It is suggested that the continent continent collision is the dominant factor controlling the Chinese tectonic stress field. The ocean continent convergence along the subduction zone is an important factor. There exists tensile boundary force along the marginal sea.
基金funded by the Natural Science Foundation of Jiangsu Province(BK20210252)。
文摘The traditional automotive catalytic converter using commercial ceramic honeycomb carriers has many problems such as high back pressure,low engine efficiency,and high usage of precious metals.This study proposes a four-channel catalytic micro-reactor based on alumina hollow fiber membrane,which uses phase inversion method for structural molding and regulation.Due to the advantages of its carrier,it can achieve lower ignition temperature under low noble metal loading.With Pd/CeO_(2) at a loading rate of 2.3%(mass),the result showed that the reaction ignition temperature is even less than 160℃,which is more than 90℃ lower than the data of commercial ceramic substrates under similar catalyst loading and airspeed conditions.The technology in turn significantly reduces the energy consumption of the reaction.And stability tests were conducted under constant conditions for 1000 h,which proved that this catalytic converter has high catalytic efficiency and stability,providing prospects for the design of innovative catalytic converters in the future.
基金Supported by the funding from "135" Projects Fund of CAS-QIBEBT Director Innovation FoundationThink-Tank Mutual Fund of Qingdao Energy Storage Industry Scientific Research+3 种基金Qingdao Key Lab of Solar Energy Utilization and Energy Storage Technologythe Strategic Priority Research Program of the Chinese Academy of Sciences(XDA09010105)National Natural Science Foundation of China(51502319)Shandong Provincial Natural Science Foundation(ZR2016BQ18)
文摘In this work,a sponge-like polysulfonamide(PSA)/SiO_2 composite membrane is unprecedentedly prepared by the phase inversion method,and successfully demonstrated as a novel separator of lithium-ion batteries(LIBs).Compared to the commercial polypropylene(PP) separator,the sponge-like PSA/SiO_2 composite possesses better physical and electrochemical properties,such as higher porosity,ionic conductivity,thermal stability and flame retarding ability.The LiCoO_2/Li half-cells using the sponge-like composite separator demonstrate superior rate capability and cyclability over those using the commercial PP separator.Moreover,the sponge-like composite separator can ensure the normal operation of LiCoO_2/Li half-cell at an extremely high temperature of 90 °C,while the commercial PP separator cannot.All these encouraging results suggest that this phase inversion based sponge-like PSA/SiO_2 composite separator is really a promising separator for high performance LIBs.
