Ce3+-doped Mn-Zn ferrite fibers were successfully prepared by the organic gel-thermal decomposition method from metal salts and citric acid. The composition,structure,and magnetic properties of these ferrite fibers we...Ce3+-doped Mn-Zn ferrite fibers were successfully prepared by the organic gel-thermal decomposition method from metal salts and citric acid. The composition,structure,and magnetic properties of these ferrite fibers were characterized by X-ray diffraction (XRD),scanning electron microscopy (SEM),and vibrating sample magnetometer (VSM). The results show that Mn0.2Zn0.8Fe2-xCexO4 (x = 0-0.04) fibers are featured with an average grain size of 11.6-12.7 nm,with diameters ranging between 1.0 to 3.5 μm and a high ...展开更多
The fine powders of Mn-Zn ferrites with uniform size were prepared via chemical co- precipitation method. X-ray diffraction analysis （XRD）, scanning electron microscopy （SEM）, vibrating sample magnetometer （VSM）...The fine powders of Mn-Zn ferrites with uniform size were prepared via chemical co- precipitation method. X-ray diffraction analysis （XRD）, scanning electron microscopy （SEM）, vibrating sample magnetometer （VSM）, frequency dependence of permeability and metallographical microscope were used to investigate the crystal structure, surface topography and magnetic properties of the powders and the sintering samples. The experimental results demonstrate that the precursor powders have formed a pure phase cubic spinel MnxZn1-xfe2O4 while in the reactor and show definite magnetism, which can solve the difficult issue in washing process effectively. When calcined beneath 450 ℃, the powders have intact crystal form and the crystallite size is less than 20 nm. Comparison tests of sintering temperatures show that 1 300 ℃ is the ideal sintering temperature for Mn-Zn ferrites prepared by using the chemical co-precipitation.展开更多
The effects of additive SnO2 (0.4wt.%), with and without SiO2 (0.02wt.%) and/or CaO (0.04wt.%), on the microstructure and magnetic properties of Mn-Zn ferrites were reported. The results reveal that SnO2 on its own in...The effects of additive SnO2 (0.4wt.%), with and without SiO2 (0.02wt.%) and/or CaO (0.04wt.%), on the microstructure and magnetic properties of Mn-Zn ferrites were reported. The results reveal that SnO2 on its own increases the initial permeability (μi) slightly, but SnO2 with SiO2 and/or CaO decreases the values of μi. However, ferrites with SnO2 additions have reduced power losses. The separate contributions of hysteresis loss and eddy current loss to the total power loss show that SnO2 (with or without SiO2 and/or CaO) doping increases the hysteresis loss slightly, but SnO2 doping alone reduces the eddy current loss significantly (～14%). The additions of SiO2 or CaO further decrease the eddy current loss, and by interaction of SnO2-CaO-SiO2, the eddy current loss is reduced by more than 20%. These magnetic and microstructural effects were discussed in terms of the additive-impurity interaction, the existence of grain boundary phases, and the effective bulk and grain boundary resistivities of the ferrites.展开更多
Mn-Zn ferrites （Mn1-xZnxFe2O4） with different compositions were prepared by the coprecipitation method, and the influences of such synthesis conditions as pH value, composition and volume ratio （R） of the mixed so...Mn-Zn ferrites （Mn1-xZnxFe2O4） with different compositions were prepared by the coprecipitation method, and the influences of such synthesis conditions as pH value, composition and volume ratio （R） of the mixed solution and NH4HCO3 solution on their microstructures and magnetic properties were discussed. The samples were characterized by X-ray diffraction （XRD） and magnetization measurement instrument. Lattice parameters and average crystalline size of the synthesized materials were calculated from the corresponding XRD patterns with the related software Jade.5. For samples of different pH values, only one phase was found when pH values were 7.0, 8.0 and 9.0. The sample with pH value of 7.0 exhibited the highest saturation magnetic induction, the lowest coercive force, and crystallized best. For samples of different R values with pH value of 7.0, only one phase was observed in all samples, and the sample with R value of 2.3 exhibited the highest saturation magnetic induction and the lowest coercive force. The composition has mainly afected the magnetic properties, and the saturation magnetic induction increases with the increase of the content of Zn （x）, but decreases when x is beyond 0.6. The trend of coercive force is on the contrary. However, no magnetism is exhibited when the x value is up to 0.8.展开更多
Effect of the content of dopants in the manganese-zinc ferrites on the low power loss is studied by measuring magnetic properties and observing the grain boundary structures. The Mn0.738Zn0.206Fe2.066O4 composition po...Effect of the content of dopants in the manganese-zinc ferrites on the low power loss is studied by measuring magnetic properties and observing the grain boundary structures. The Mn0.738Zn0.206Fe2.066O4 composition powders were prepared by using conventional ceramic powder processing technique. The microstructure of grain boundary was observed by scanning electron microscope （SEM）. It has been found that power loss is greatly dependent upon the content of the additives.展开更多
The density, microstructure and magnetic properties of non-doped Mn-Zn ferrite nanoparticles sintered compacts were investigated. The compacts of non-doped Mn-Zn ferrite nanoparticles were sintered by segmented-sinter...The density, microstructure and magnetic properties of non-doped Mn-Zn ferrite nanoparticles sintered compacts were investigated. The compacts of non-doped Mn-Zn ferrite nanoparticles were sintered by segmented-sintering process at lower sintering temperature. The density of sintered samples was measured by Archimedes method, and the phase composition and microstructure were examined by XRD and SEM. The sintered Mn-Zn ferrite magnetic measurements were carried out with Vibrating Sample. The results show that the density of sintered compacts increases with the rising of sintering temperature, achieving 4.8245 g·cm-3 when sintered at 900 ℃, which is the optimal density of Mn-Zn functional ferrite needed and from the fractured surface of sintered samples, it can be seen that the grain grows well with small grain size and homogeneous distribution.展开更多
Nanosized Mn-Zn ferrite doped with Nd (Mn_ 0.6Zn_ 0.4Nd_xFe_ 2-xO_4) were fabricated by hydrothermal precipitation route and studied by XRD, TEM, DSC and VSM. The effects of Nd doping on manganese zinc ferrites were d...Nanosized Mn-Zn ferrite doped with Nd (Mn_ 0.6Zn_ 0.4Nd_xFe_ 2-xO_4) were fabricated by hydrothermal precipitation route and studied by XRD, TEM, DSC and VSM. The effects of Nd doping on manganese zinc ferrites were discussed. The results show that the samples with a small amount of Nd doping are spinel crystal structure and uniformly nanosized particles with little aggregation. DSC analysis of Mn_ 0.6Zn_ 0.4Fe_2O_4 and Mn_ 0.6Zn_ 0.4Nd_ 0.06Fe_ 1.94O_4 samples both present two exothermic peaks ascribed to the redistribution of Mn 2+, Zn 2+ and Fe 3+ ions in the two sub-lattices (tetrahedral (A) and octahedral (B) sites), and the oxidation of Mn 2+-ions at higher temperatures respectively. The saturation magnetization (M_s) for Mn_ 0.6Zn_ 0.4Nd_xFe_ 2-xO_4 ferrites increase with (x) up to 0.06 and decrease for higher concentrations. And supermagnetic behavior was observed at 25 ℃ in the M-H loops of Mn_ 0.6Zn_ 0.4Fe_2O_4 and Mn_ 0.6Zn_ 0.4Nd_ 0.06Fe_ 1.94O_4 samples for their extremely small sizes.展开更多
The microwave absorbing behaviour of Mn-Zn ferrite sintered at 1100,1200,1300,1400 and 1500℃ has been investigated.The phase constitution of the ferrite was analyzed by X-ray diffraction.The results show that the fer...The microwave absorbing behaviour of Mn-Zn ferrite sintered at 1100,1200,1300,1400 and 1500℃ has been investigated.The phase constitution of the ferrite was analyzed by X-ray diffraction.The results show that the ferrite sintered at 1 500℃ has better microwave absorbing prop- erty than those prepared at other temperatures,due to the increase of turbulent loss generated by the formation of excessive Fe^(2+) in deoxidizing of Fe_2O_3 at high temperatures.展开更多
Mn-Zn spinel ferrites were synthesized by sol-gel method. Effects of calcined temperature on structure and particle size of MnZnFe2O4 were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM)...Mn-Zn spinel ferrites were synthesized by sol-gel method. Effects of calcined temperature on structure and particle size of MnZnFe2O4 were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD patterns indicate that the ultra fine Mn-Zn ferrite exhibits a spinel crystal structure. SEM images show that the powder fired at 900℃for 2 h has an average diameter of 60 ~ 90 nm. The particle size becomes larger with the increasing of calcined temperature and the distribution of particle becomes even more homogeneous. Sintering behaviors of synthesized ferrite powders depend on the powder characteristics and high temperatures have induced the good crystallization of particles.展开更多
Soft ferrites have excellent a.c.permeability, but it is reduced under stress.It has a hyperbolic re- lationship between permeability μ and stress σ or a linear increase of 1/μ with σ.It is also found that the str...Soft ferrites have excellent a.c.permeability, but it is reduced under stress.It has a hyperbolic re- lationship between permeability μ and stress σ or a linear increase of 1/μ with σ.It is also found that the stress sensitive factor α depends on sample porosity p.For fully densified Mn-Zn ferrites α is only 10^(-7)～10^(-8) MPa^(-1),but it increases to 6× 10^(-6) MPa^(-1) for samples containing closed porosity 6%.Such materials could be used as a sensor for measuring pressure。展开更多
Magnesium-substituted Mn0.8Zn0.2Fe2O4 ferrite is synthesized by the sol–gel combustion method using citrate acid as the complex agent. The electromagnetic absorbing behaviors of ferrite/polymer coatings fabricated by...Magnesium-substituted Mn0.8Zn0.2Fe2O4 ferrite is synthesized by the sol–gel combustion method using citrate acid as the complex agent. The electromagnetic absorbing behaviors of ferrite/polymer coatings fabricated by dispersing Mn–Zn ferrite into epoxy resin （EP） are studied. The microstructure and morphology are characterized by X-ray diffraction and scanning electron microscope. Complex permittivity, complex permeability, and reflection loss of ferrite/EP composite coating are investigated in a low frequency range. It is found that the prepared ferrite particles are traditional cubic spinel ferrite particles with an average size of 200 nm. The results reveal that the electromagnetic microwave absorbing properties are significantly influenced by the weight ratio of ferrite to polymer. The composites with a weight ratio of ferrite/polymer being 3：20 have a maximum reflection loss of –16 dB and wide absorbing band. Thus, the Mn–Zn ferrite is the potential candidate in electromagnetic absorbing application in the low frequency range （10 MHz–1 GHz）.展开更多
The impact of Cr3+ ion on the magnetic properties of Mn0.50Zn0.50CrxFe2-xO4 (with x = 0.0, 0.1, 0.2, 0.3, 0.4 and 0.5) has been studied. Ferrite samples were synthesized by combustion method and sintered at various te...The impact of Cr3+ ion on the magnetic properties of Mn0.50Zn0.50CrxFe2-xO4 (with x = 0.0, 0.1, 0.2, 0.3, 0.4 and 0.5) has been studied. Ferrite samples were synthesized by combustion method and sintered at various temperatures (1250°C, 1300°C and 1350°C). The structural properties were investigated by means of X-ray diffraction patterns and indicated that the samples possess single phase cubic spinel structure. The lattice parameter decreases with the increase in Cr3+ content, as the ionic radius of Cr3+ ion is smaller than that of Fe3+. The average grain size (D), bulk density (ρB) and initial permeability (μi’ )decreases with increase in Cr3+ content whereas porosity follows its opposite trend. The ρB was found to increase with increase in Cr3+ content as the sintering temperature (Ts) is increased from 1250°C to 1350°C. The Ts affects the densification, grain growth and (μi’ ) of the samples. The (μi’ ) strongly depends on average grain size, density and intragranular porosity. The B-H loops of the compositions were measured at room temperature. The saturation magnetization (Ms), coercivity (Hc) and hysteresis losses were studied as a function of Cr3+ content. The Ms was found to decrease with the increase of Cr3+ content, which is attributed to the dilution of A-B interaction.展开更多
Pure MnO2, ZnO and Fe2O3 were used to prepare a Mn-Zn Ferrite sample of the nominal composition Mn0.64Zn0.29Fe2.07O4. These oxides were mixed firstly for 1hr, and then were milled for 20 and for 40 hrs. The as-mixed a...Pure MnO2, ZnO and Fe2O3 were used to prepare a Mn-Zn Ferrite sample of the nominal composition Mn0.64Zn0.29Fe2.07O4. These oxides were mixed firstly for 1hr, and then were milled for 20 and for 40 hrs. The as-mixed and the milled powders were examined by XRD and ME spectroscopy. The investigated samples were further mixed with PVA, granulated, cold pressed and sintered at different temperatures (1000, 1300 and 1400 oC) for 2 hrs and were then reinvestigated again. The magnetic properties of all samples before and after sintering were characterized using VSM at a field of 15 k Oe. When the powder oxides were milled for 20 hrs, detectable diffusion reaction was observed where the centers of all XRD peaks (due to Fe2O3 and MnO2) shifted to higher 2? angles, suggesting that Zn2+ cations had diffused through Fe3+ and/or Mn4+ lattices. The observed increase in the width of the XRD peaks can be attributed to the refinement of the powders by milling. Milling of the powder for 40 hrs resulted in the formation of spinel phase of (Zn, Fe), but MnO2 was disappeared probably due to the formation of amorphous structure. Sintering at 1000, 1300, and 1400 oC resulted in the formation of different spinel (Mn-Zn) ferrites. The ME measurements followed the gradual formation the manganese zinc ferrite until complete formation which observed in the sample that milled for 40 hrs followed by sintering at 1300 oC for two hrs. However, it can be concluded that, the processing conditions of such sample represent are the best conditions for obtaining a soft manganese zinc ferrite (single phase).展开更多
Mn-Zn ferrite powders were produced from low-grade manganese ore(LMO) via the chemical coprecipitation method combined with the ceramic method,after the LMO was leached in sulfuric acid and the obtained solution was p...Mn-Zn ferrite powders were produced from low-grade manganese ore(LMO) via the chemical coprecipitation method combined with the ceramic method,after the LMO was leached in sulfuric acid and the obtained solution was purified.The effect of the pH on the magnetic properties of Mn-Zn ferrite was investigated by the varying pH of the co-precipitation system.The crystal structure and phases of the samples were characterized by X-ray diffraction and infrared spectrum,respectively.The magnetic measurements were carried out on a vibrating sample magnetometer.The optimal sample was obtained with a saturation magnetization of 55.02 emu/g,a coercivity of 8.20 G and a remanent magnetization of1.71 emu/g when pH is 7.5.展开更多
A new structure of integrated low-pass LC filter of DC-DC power converter is proposed in this paper. This filter consists in a circular planar coil enclosed between two ferrites substrates. Mn-Zn ferrite has been chos...A new structure of integrated low-pass LC filter of DC-DC power converter is proposed in this paper. This filter consists in a circular planar coil enclosed between two ferrites substrates. Mn-Zn ferrite has been chosen because of its high permeability and permittivity. In this filter Mn-Zn substrates act not only as a magnetic core but also as a capacitor. In order to reduce the conduction losses in the part of the ferrite used as a capacitor, a particular topology using a blocking layer is proposed. A modelling of the dielectric behaviour of the materials has been performed and injected in a simulation in order to find the resulting LC filter performances and its power range of use. In order to increase the filter efficiency, different solutions have been explored. In particular the inter-turn gap evolution has been optimized to reduce the inter-turn losses. Regarding the bulk losses, BaTiO3?blocking layers have?been added, either upon the ground or the conductor. In this last case a co-firing ferrite tape has been inserted between turns to increase the LC product. Finally the use of low losses Mn-Zn and BaTiO3?has been proposed and the final characteristics (both electrical and dimensional) of our filter have been compared toconventional ones.展开更多
Permanent ferrite magnet materials are extensively employed due to their exceptional magnetic properties and cost-effectiveness.The fast development in electromobile and household appliance industries contributes to a...Permanent ferrite magnet materials are extensively employed due to their exceptional magnetic properties and cost-effectiveness.The fast development in electromobile and household appliance industries contributes to a new progress in permanent ferrite materials.This paper reviews the deveolpement and progress of permanent ferrite magnet industry in recent years.The emergence of new raw material,the advancement of perparation methods and manufacturing techniques,and the potential applications of permanent ferrite materials are introduced and discussed.Specifically,nanocrystallization plays a crucial role in achieving high performance at a low cost and reducing reliance on rare earth resources,and therefore it could be a promising development trendency.展开更多
This review paper explores the efficacy of magnesium ferrite-based catalysts in photocatalytic degradation of organic contaminates(antibiotic and dyes).We report the influence of different doping strategies,synthesis ...This review paper explores the efficacy of magnesium ferrite-based catalysts in photocatalytic degradation of organic contaminates(antibiotic and dyes).We report the influence of different doping strategies,synthesis methods,and composite materials on the degradation efficiency of these pollutants.Our analysis reveals the versatile and promising nature of magnesium ferrite-based catalysts,offering the valuable insights into their practical application for restoring the environment.Due to the smaller band gap and magnetic nature of magnesium ferrite,it holds the benefit of utilising the broader spectrum of light while also being recoverable.The in-depth analysis of magnesium ferrites'photocatalytic mechanism could lead to the development of cheap and reliable photocatalyst for the wastewater treatment.This concise review offers a thorough summary of the key advancements in this field,highlighting the pivotal role of the magnesium ferrite based photocatalysts in addressing the pressing global issue of organic pollutants in wastewater.展开更多
A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling t...A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.展开更多
Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural co...Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural configuration.Herein,we employ controlled Co doping to effectively enhance the nanoparticle exsolution process in layered perovskite ferrites materials.CoFe alloy nanoparticles with ultra-high-density are exsolved on the(PrBa)_(0.95)(Fe_(0.8)Co_(0.1)Nb_(0.1))2O_(5+δ)(PBFCN_(0.1))surface under reducing atmosphere,providing significant amounts of reaction sites and good durability for hydrocarbon catalysis.Under a reducing atmosphere,cobalt facilitates the reduction of iron cations within PBFCN_(0.1),leading to the formation of CoFe alloy nanoparticles.This formation is accompanied by a cation exchange process,wherein,with the increase in temperature,partial cobalt ions are substituted by iron.Meanwhile,Co doping significantly enhance the electrical conductivity due to the stronger covalency of the Cosingle bondO bond compared with Fesingle bondO bond.A single cell with the configuration of PBFCN_(0.1)-Sm_(0.2)Ce_(0.8)O_(1.9)(SDC)|SDC|Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_(3−δ)(BSCF)-SDC achieves an extremely low polarization resistance of 0.0163Ωcm^(2)and a high peak power density of 740 mW cm^(−2)at 800℃.The cell also shows stable operation for 120 h in H_(2)with a constant current density of 285 mA cm^(−2).Furthermore,employing wet C_(2)H_(6)as fuel,the cell demonstrates remarkable performance,achieving peak power densities of 455 mW cm^(−2)at 800℃and 320 mW cm^(−2)at 750℃,marking improvements of 36%and 70%over the cell with(PrBa)_(0.95)(Fe_(0.9)Nb_(0.1))_(2)O_(5+δ)(PBFN)-SDC at these respective temperatures.This discovery emphasizes how temperature influences alloy nanoparticles exsolution within doped layered perovskite ferrites materials,paving the way for the development of high-performance ceramic fuel cell anodes.展开更多
A novel topology of modular ferrite magnet fluxswitching linear motor(FMFSLM)use for track transport is presented in this paper,which enables more ferrite magnets to be inserted into the primary iron core.The motor ha...A novel topology of modular ferrite magnet fluxswitching linear motor(FMFSLM)use for track transport is presented in this paper,which enables more ferrite magnets to be inserted into the primary iron core.The motor has a significant low-cost advantage in long-distance linear drive.The proposed FMFSLM’s structure and working principle were introduced.Further,the thrust force expression of the motor was established.The thrust force components triggering thrust force ripple were investigated,and their expressions can be obtained according to the inductances’Fourier series expressions.Resultantly,the relationship between the harmonics of thrust force and that of self-and mutual inductances was revealed clearly.Based on the relationship,a skewed secondary should be practical to reduce the thrust force ripple.Thus,the effect of employing a skewed secondary to the proposed FMFSLM was investigated,and an optimized skewing span distance was determined.Finite element analysis(FEA)was conducted to validate the exactness of the theoretical analysis.The simulation results indicate that the strategy of suppressing thrust force ripple has a significant effect.Meanwhile,the motor maintains a good efficiency characteristic.The results of the prototype experiment are in good agreement with FEAs,which further verifies the proposed modular interior FMFSLM’s practicability.展开更多
基金the National Natural Science Foundation of China (No. 50674048)the Avigation Science Foundation of China (No. 2007ZF52062)
文摘Ce3+-doped Mn-Zn ferrite fibers were successfully prepared by the organic gel-thermal decomposition method from metal salts and citric acid. The composition,structure,and magnetic properties of these ferrite fibers were characterized by X-ray diffraction (XRD),scanning electron microscopy (SEM),and vibrating sample magnetometer (VSM). The results show that Mn0.2Zn0.8Fe2-xCexO4 (x = 0-0.04) fibers are featured with an average grain size of 11.6-12.7 nm,with diameters ranging between 1.0 to 3.5 μm and a high ...
基金Funded by the National Natural Science Foundation of China(Nos.51162019 and 51462019)
文摘The fine powders of Mn-Zn ferrites with uniform size were prepared via chemical co- precipitation method. X-ray diffraction analysis （XRD）, scanning electron microscopy （SEM）, vibrating sample magnetometer （VSM）, frequency dependence of permeability and metallographical microscope were used to investigate the crystal structure, surface topography and magnetic properties of the powders and the sintering samples. The experimental results demonstrate that the precursor powders have formed a pure phase cubic spinel MnxZn1-xfe2O4 while in the reactor and show definite magnetism, which can solve the difficult issue in washing process effectively. When calcined beneath 450 ℃, the powders have intact crystal form and the crystallite size is less than 20 nm. Comparison tests of sintering temperatures show that 1 300 ℃ is the ideal sintering temperature for Mn-Zn ferrites prepared by using the chemical co-precipitation.
文摘The effects of additive SnO2 (0.4wt.%), with and without SiO2 (0.02wt.%) and/or CaO (0.04wt.%), on the microstructure and magnetic properties of Mn-Zn ferrites were reported. The results reveal that SnO2 on its own increases the initial permeability (μi) slightly, but SnO2 with SiO2 and/or CaO decreases the values of μi. However, ferrites with SnO2 additions have reduced power losses. The separate contributions of hysteresis loss and eddy current loss to the total power loss show that SnO2 (with or without SiO2 and/or CaO) doping increases the hysteresis loss slightly, but SnO2 doping alone reduces the eddy current loss significantly (～14%). The additions of SiO2 or CaO further decrease the eddy current loss, and by interaction of SnO2-CaO-SiO2, the eddy current loss is reduced by more than 20%. These magnetic and microstructural effects were discussed in terms of the additive-impurity interaction, the existence of grain boundary phases, and the effective bulk and grain boundary resistivities of the ferrites.
基金Funded by the Basic Key Project in Shanghai City (06JC14033)the Key Discipline Construction Fund in Shanghai City (P1304)
文摘Mn-Zn ferrites （Mn1-xZnxFe2O4） with different compositions were prepared by the coprecipitation method, and the influences of such synthesis conditions as pH value, composition and volume ratio （R） of the mixed solution and NH4HCO3 solution on their microstructures and magnetic properties were discussed. The samples were characterized by X-ray diffraction （XRD） and magnetization measurement instrument. Lattice parameters and average crystalline size of the synthesized materials were calculated from the corresponding XRD patterns with the related software Jade.5. For samples of different pH values, only one phase was found when pH values were 7.0, 8.0 and 9.0. The sample with pH value of 7.0 exhibited the highest saturation magnetic induction, the lowest coercive force, and crystallized best. For samples of different R values with pH value of 7.0, only one phase was observed in all samples, and the sample with R value of 2.3 exhibited the highest saturation magnetic induction and the lowest coercive force. The composition has mainly afected the magnetic properties, and the saturation magnetic induction increases with the increase of the content of Zn （x）, but decreases when x is beyond 0.6. The trend of coercive force is on the contrary. However, no magnetism is exhibited when the x value is up to 0.8.
基金Project supported by National High-Technology Research and De-velopment Program(Grant No .2001AA3250380)
文摘Effect of the content of dopants in the manganese-zinc ferrites on the low power loss is studied by measuring magnetic properties and observing the grain boundary structures. The Mn0.738Zn0.206Fe2.066O4 composition powders were prepared by using conventional ceramic powder processing technique. The microstructure of grain boundary was observed by scanning electron microscope （SEM）. It has been found that power loss is greatly dependent upon the content of the additives.
基金This work was financially supported by the Natural Science Fund of Hebei Province, China (No.E2005000027), and the Natural Science Foundation of Tianjin, China (No.06YFJMJC02400).
文摘The density, microstructure and magnetic properties of non-doped Mn-Zn ferrite nanoparticles sintered compacts were investigated. The compacts of non-doped Mn-Zn ferrite nanoparticles were sintered by segmented-sintering process at lower sintering temperature. The density of sintered samples was measured by Archimedes method, and the phase composition and microstructure were examined by XRD and SEM. The sintered Mn-Zn ferrite magnetic measurements were carried out with Vibrating Sample. The results show that the density of sintered compacts increases with the rising of sintering temperature, achieving 4.8245 g·cm-3 when sintered at 900 ℃, which is the optimal density of Mn-Zn functional ferrite needed and from the fractured surface of sintered samples, it can be seen that the grain grows well with small grain size and homogeneous distribution.
文摘Nanosized Mn-Zn ferrite doped with Nd (Mn_ 0.6Zn_ 0.4Nd_xFe_ 2-xO_4) were fabricated by hydrothermal precipitation route and studied by XRD, TEM, DSC and VSM. The effects of Nd doping on manganese zinc ferrites were discussed. The results show that the samples with a small amount of Nd doping are spinel crystal structure and uniformly nanosized particles with little aggregation. DSC analysis of Mn_ 0.6Zn_ 0.4Fe_2O_4 and Mn_ 0.6Zn_ 0.4Nd_ 0.06Fe_ 1.94O_4 samples both present two exothermic peaks ascribed to the redistribution of Mn 2+, Zn 2+ and Fe 3+ ions in the two sub-lattices (tetrahedral (A) and octahedral (B) sites), and the oxidation of Mn 2+-ions at higher temperatures respectively. The saturation magnetization (M_s) for Mn_ 0.6Zn_ 0.4Nd_xFe_ 2-xO_4 ferrites increase with (x) up to 0.06 and decrease for higher concentrations. And supermagnetic behavior was observed at 25 ℃ in the M-H loops of Mn_ 0.6Zn_ 0.4Fe_2O_4 and Mn_ 0.6Zn_ 0.4Nd_ 0.06Fe_ 1.94O_4 samples for their extremely small sizes.
文摘The microwave absorbing behaviour of Mn-Zn ferrite sintered at 1100,1200,1300,1400 and 1500℃ has been investigated.The phase constitution of the ferrite was analyzed by X-ray diffraction.The results show that the ferrite sintered at 1 500℃ has better microwave absorbing prop- erty than those prepared at other temperatures,due to the increase of turbulent loss generated by the formation of excessive Fe^(2+) in deoxidizing of Fe_2O_3 at high temperatures.
基金Project supported by the Fund for Harbin Young Scholars (2005AFQXJ031)
文摘Mn-Zn spinel ferrites were synthesized by sol-gel method. Effects of calcined temperature on structure and particle size of MnZnFe2O4 were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD patterns indicate that the ultra fine Mn-Zn ferrite exhibits a spinel crystal structure. SEM images show that the powder fired at 900℃for 2 h has an average diameter of 60 ~ 90 nm. The particle size becomes larger with the increasing of calcined temperature and the distribution of particle becomes even more homogeneous. Sintering behaviors of synthesized ferrite powders depend on the powder characteristics and high temperatures have induced the good crystallization of particles.
文摘Soft ferrites have excellent a.c.permeability, but it is reduced under stress.It has a hyperbolic re- lationship between permeability μ and stress σ or a linear increase of 1/μ with σ.It is also found that the stress sensitive factor α depends on sample porosity p.For fully densified Mn-Zn ferrites α is only 10^(-7)～10^(-8) MPa^(-1),but it increases to 6× 10^(-6) MPa^(-1) for samples containing closed porosity 6%.Such materials could be used as a sensor for measuring pressure。
基金Project supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China(Grant No.20121101110014)
文摘Magnesium-substituted Mn0.8Zn0.2Fe2O4 ferrite is synthesized by the sol–gel combustion method using citrate acid as the complex agent. The electromagnetic absorbing behaviors of ferrite/polymer coatings fabricated by dispersing Mn–Zn ferrite into epoxy resin （EP） are studied. The microstructure and morphology are characterized by X-ray diffraction and scanning electron microscope. Complex permittivity, complex permeability, and reflection loss of ferrite/EP composite coating are investigated in a low frequency range. It is found that the prepared ferrite particles are traditional cubic spinel ferrite particles with an average size of 200 nm. The results reveal that the electromagnetic microwave absorbing properties are significantly influenced by the weight ratio of ferrite to polymer. The composites with a weight ratio of ferrite/polymer being 3：20 have a maximum reflection loss of –16 dB and wide absorbing band. Thus, the Mn–Zn ferrite is the potential candidate in electromagnetic absorbing application in the low frequency range （10 MHz–1 GHz）.
文摘The impact of Cr3+ ion on the magnetic properties of Mn0.50Zn0.50CrxFe2-xO4 (with x = 0.0, 0.1, 0.2, 0.3, 0.4 and 0.5) has been studied. Ferrite samples were synthesized by combustion method and sintered at various temperatures (1250°C, 1300°C and 1350°C). The structural properties were investigated by means of X-ray diffraction patterns and indicated that the samples possess single phase cubic spinel structure. The lattice parameter decreases with the increase in Cr3+ content, as the ionic radius of Cr3+ ion is smaller than that of Fe3+. The average grain size (D), bulk density (ρB) and initial permeability (μi’ )decreases with increase in Cr3+ content whereas porosity follows its opposite trend. The ρB was found to increase with increase in Cr3+ content as the sintering temperature (Ts) is increased from 1250°C to 1350°C. The Ts affects the densification, grain growth and (μi’ ) of the samples. The (μi’ ) strongly depends on average grain size, density and intragranular porosity. The B-H loops of the compositions were measured at room temperature. The saturation magnetization (Ms), coercivity (Hc) and hysteresis losses were studied as a function of Cr3+ content. The Ms was found to decrease with the increase of Cr3+ content, which is attributed to the dilution of A-B interaction.
文摘Pure MnO2, ZnO and Fe2O3 were used to prepare a Mn-Zn Ferrite sample of the nominal composition Mn0.64Zn0.29Fe2.07O4. These oxides were mixed firstly for 1hr, and then were milled for 20 and for 40 hrs. The as-mixed and the milled powders were examined by XRD and ME spectroscopy. The investigated samples were further mixed with PVA, granulated, cold pressed and sintered at different temperatures (1000, 1300 and 1400 oC) for 2 hrs and were then reinvestigated again. The magnetic properties of all samples before and after sintering were characterized using VSM at a field of 15 k Oe. When the powder oxides were milled for 20 hrs, detectable diffusion reaction was observed where the centers of all XRD peaks (due to Fe2O3 and MnO2) shifted to higher 2? angles, suggesting that Zn2+ cations had diffused through Fe3+ and/or Mn4+ lattices. The observed increase in the width of the XRD peaks can be attributed to the refinement of the powders by milling. Milling of the powder for 40 hrs resulted in the formation of spinel phase of (Zn, Fe), but MnO2 was disappeared probably due to the formation of amorphous structure. Sintering at 1000, 1300, and 1400 oC resulted in the formation of different spinel (Mn-Zn) ferrites. The ME measurements followed the gradual formation the manganese zinc ferrite until complete formation which observed in the sample that milled for 40 hrs followed by sintering at 1300 oC for two hrs. However, it can be concluded that, the processing conditions of such sample represent are the best conditions for obtaining a soft manganese zinc ferrite (single phase).
基金financed by the Bureau of Land Resources and Housing Management of Chongqing(Scientific & Technologic Program in 2011)the Science and Technology Bureau of Hengyang(Scientific & Technologic Program in 2013)the State Administration of Work Safety(Scientific & Technologic Program in 2013)
文摘Mn-Zn ferrite powders were produced from low-grade manganese ore(LMO) via the chemical coprecipitation method combined with the ceramic method,after the LMO was leached in sulfuric acid and the obtained solution was purified.The effect of the pH on the magnetic properties of Mn-Zn ferrite was investigated by the varying pH of the co-precipitation system.The crystal structure and phases of the samples were characterized by X-ray diffraction and infrared spectrum,respectively.The magnetic measurements were carried out on a vibrating sample magnetometer.The optimal sample was obtained with a saturation magnetization of 55.02 emu/g,a coercivity of 8.20 G and a remanent magnetization of1.71 emu/g when pH is 7.5.
文摘A new structure of integrated low-pass LC filter of DC-DC power converter is proposed in this paper. This filter consists in a circular planar coil enclosed between two ferrites substrates. Mn-Zn ferrite has been chosen because of its high permeability and permittivity. In this filter Mn-Zn substrates act not only as a magnetic core but also as a capacitor. In order to reduce the conduction losses in the part of the ferrite used as a capacitor, a particular topology using a blocking layer is proposed. A modelling of the dielectric behaviour of the materials has been performed and injected in a simulation in order to find the resulting LC filter performances and its power range of use. In order to increase the filter efficiency, different solutions have been explored. In particular the inter-turn gap evolution has been optimized to reduce the inter-turn losses. Regarding the bulk losses, BaTiO3?blocking layers have?been added, either upon the ground or the conductor. In this last case a co-firing ferrite tape has been inserted between turns to increase the LC product. Finally the use of low losses Mn-Zn and BaTiO3?has been proposed and the final characteristics (both electrical and dimensional) of our filter have been compared toconventional ones.
基金Project(1053320222852)supported by the Graduate Student Innovation Program of Central South University,China。
文摘Permanent ferrite magnet materials are extensively employed due to their exceptional magnetic properties and cost-effectiveness.The fast development in electromobile and household appliance industries contributes to a new progress in permanent ferrite materials.This paper reviews the deveolpement and progress of permanent ferrite magnet industry in recent years.The emergence of new raw material,the advancement of perparation methods and manufacturing techniques,and the potential applications of permanent ferrite materials are introduced and discussed.Specifically,nanocrystallization plays a crucial role in achieving high performance at a low cost and reducing reliance on rare earth resources,and therefore it could be a promising development trendency.
文摘This review paper explores the efficacy of magnesium ferrite-based catalysts in photocatalytic degradation of organic contaminates(antibiotic and dyes).We report the influence of different doping strategies,synthesis methods,and composite materials on the degradation efficiency of these pollutants.Our analysis reveals the versatile and promising nature of magnesium ferrite-based catalysts,offering the valuable insights into their practical application for restoring the environment.Due to the smaller band gap and magnetic nature of magnesium ferrite,it holds the benefit of utilising the broader spectrum of light while also being recoverable.The in-depth analysis of magnesium ferrites'photocatalytic mechanism could lead to the development of cheap and reliable photocatalyst for the wastewater treatment.This concise review offers a thorough summary of the key advancements in this field,highlighting the pivotal role of the magnesium ferrite based photocatalysts in addressing the pressing global issue of organic pollutants in wastewater.
文摘A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.
基金supported by National Natural Science Foundation of China Project (Grant No. 52374133, 52262034)the Guangdong Basic and Applied Basic Research Committee Foundation (Grant No. KCXST20221021111601003)Shenzhen Science and Technology Innovation Commission Foundation (Grant No. KCXST20221021111601003)
文摘Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural configuration.Herein,we employ controlled Co doping to effectively enhance the nanoparticle exsolution process in layered perovskite ferrites materials.CoFe alloy nanoparticles with ultra-high-density are exsolved on the(PrBa)_(0.95)(Fe_(0.8)Co_(0.1)Nb_(0.1))2O_(5+δ)(PBFCN_(0.1))surface under reducing atmosphere,providing significant amounts of reaction sites and good durability for hydrocarbon catalysis.Under a reducing atmosphere,cobalt facilitates the reduction of iron cations within PBFCN_(0.1),leading to the formation of CoFe alloy nanoparticles.This formation is accompanied by a cation exchange process,wherein,with the increase in temperature,partial cobalt ions are substituted by iron.Meanwhile,Co doping significantly enhance the electrical conductivity due to the stronger covalency of the Cosingle bondO bond compared with Fesingle bondO bond.A single cell with the configuration of PBFCN_(0.1)-Sm_(0.2)Ce_(0.8)O_(1.9)(SDC)|SDC|Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_(3−δ)(BSCF)-SDC achieves an extremely low polarization resistance of 0.0163Ωcm^(2)and a high peak power density of 740 mW cm^(−2)at 800℃.The cell also shows stable operation for 120 h in H_(2)with a constant current density of 285 mA cm^(−2).Furthermore,employing wet C_(2)H_(6)as fuel,the cell demonstrates remarkable performance,achieving peak power densities of 455 mW cm^(−2)at 800℃and 320 mW cm^(−2)at 750℃,marking improvements of 36%and 70%over the cell with(PrBa)_(0.95)(Fe_(0.9)Nb_(0.1))_(2)O_(5+δ)(PBFN)-SDC at these respective temperatures.This discovery emphasizes how temperature influences alloy nanoparticles exsolution within doped layered perovskite ferrites materials,paving the way for the development of high-performance ceramic fuel cell anodes.
基金supported by Shandong Provincial Natural Science Foundation under Grant ZR2020ME205.
文摘A novel topology of modular ferrite magnet fluxswitching linear motor(FMFSLM)use for track transport is presented in this paper,which enables more ferrite magnets to be inserted into the primary iron core.The motor has a significant low-cost advantage in long-distance linear drive.The proposed FMFSLM’s structure and working principle were introduced.Further,the thrust force expression of the motor was established.The thrust force components triggering thrust force ripple were investigated,and their expressions can be obtained according to the inductances’Fourier series expressions.Resultantly,the relationship between the harmonics of thrust force and that of self-and mutual inductances was revealed clearly.Based on the relationship,a skewed secondary should be practical to reduce the thrust force ripple.Thus,the effect of employing a skewed secondary to the proposed FMFSLM was investigated,and an optimized skewing span distance was determined.Finite element analysis(FEA)was conducted to validate the exactness of the theoretical analysis.The simulation results indicate that the strategy of suppressing thrust force ripple has a significant effect.Meanwhile,the motor maintains a good efficiency characteristic.The results of the prototype experiment are in good agreement with FEAs,which further verifies the proposed modular interior FMFSLM’s practicability.
