[Objectives]To determine the optimal reflux extraction process conditions for Compound Coptis Ointment.[Methods]The study employed the orthogonal experimental design method and drug-sensitive disc agar diffusion metho...[Objectives]To determine the optimal reflux extraction process conditions for Compound Coptis Ointment.[Methods]The study employed the orthogonal experimental design method and drug-sensitive disc agar diffusion method to evaluate the extraction rate,berberine hydrochloride content,and bacteriostatic ring diameter of the extract as comprehensive indices,and optimized the extraction process conditions of Compound Coptis Ointment using ethanol reflux.[Results]Based on the results of comprehensive indices,the optimal reflux extraction conditions for Compound Coptis Ointment were determined to be soaking in 1.5 times the amount of 70%ethanol for 2 h,followed by two extractions with 6 times the amount of 70%ethanol for 1 h each time.Three verification tests were conducted under the optimal process conditions.The yield of the extract was 28.32%±0.53%,the content of berberine hydrochloride was 4.68%±0.45%,and the diameter of the bacteriostatic ring was(2.5±0.2)cm.[Conclusions]The extract had higher drug content and exhibited better antibacterial effects.The optimized extraction process is simple,stable,and reliable,and can be effectively used to optimize the extraction process of Compound Coptis Ointment.展开更多
To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diamet...To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.展开更多
Biogas is a kind of regenerable energy which is inexpensive and friendly to the environment, but the potential of biogas is difficult to develop fully in China, for most biogas have badly qualities and the utilization...Biogas is a kind of regenerable energy which is inexpensive and friendly to the environment, but the potential of biogas is difficult to develop fully in China, for most biogas have badly qualities and the utilization of it is monotonous. The suitable operation term about biogas upgrading by pressurized water scrubbing was researched through the orthogonal test in this study. Two sorts of scrubber packing included the random multidimensional hollow sphere packing and the structured screen packing were also used, and the effects of experiment factors included packing, water temperature, gas flow speed, water flow speed and washing pressure were studied. The results showed that better effect was got when the screen structured packing was used; all the five test factors affected the processing significantly in the arrange as before and had better and better significant effects.展开更多
Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants ment...Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants mentioned above are installed as four factors,and three levels are selected for every factor.The test is actualized according to L 9(3 4) orthogonal array.Results An optimized recipe A 3 B 3 C 3 D 1 has been obtained after considering multifarious factors such as the resources of these plants and the water-solubility of samples.Conclusion The dry powder insecticide prepared by mixing the plant samples mentioned above as 1∶1∶1mass ratio revealed that insecticidal activities for cickets,grasshopper,aphid,and 3rd instar Mythimna separata walker are significant,respectively.展开更多
[Objectives] This study was conducted to optimize the ethanol extraction technology of monoester alkaloids from Radix Aconiti Preparata. [Methods]On the basis of defined extraction times,ethanol concentration,ethanol ...[Objectives] This study was conducted to optimize the ethanol extraction technology of monoester alkaloids from Radix Aconiti Preparata. [Methods]On the basis of defined extraction times,ethanol concentration,ethanol times and extraction time were investigated by HPLC-MS combined with orthogonal test to optimize extraction process using the content of monoester alkaloids( the sum of benzoyl neoaconitine,benzoyl hypoaconitine and benzoyl aconitine) as an index.[Results]The optimum ethanol extraction technology was as follows: 75% ethanol,ethanol amount 25 times of the medicinal material,and each extraction for 1. 5 h.[Conclusions] The optimal extraction technology is simple,feasible,stable and reliable. It can provide reference for the industrial production and quality control of monoester alkaloids from Radix Aconiti Preparata.展开更多
Objective To optimize the extract technology of active lignins from the fruits of Schisandra chinensis. Methods The content of schizandrin, gomisin A, and deoxyschizandrin were selected as standards to evaluate the ef...Objective To optimize the extract technology of active lignins from the fruits of Schisandra chinensis. Methods The content of schizandrin, gomisin A, and deoxyschizandrin were selected as standards to evaluate the efficiency of smashing tissue extraction (STE). Solid-liquid ratio, extracting times, ethanol concentration, and extracting time were investigated through orthogonal test. Results The optimized conditions for STE were ten times amount of 80% EtOH, extracting for three times, and 2 min for each time. Conclusion STE could obtain relatively higher yield, simplicity of operation, and benefit for environment protection. It could be better choice for the extraction of S. chinensis.展开更多
Objective To optimize microwave-assisted extraction of polyphenols from Enteromorpha prolifra. Methods Based on single-factor tests, an efficient microwave-assisted extraction (MAE) technique was developed to extract ...Objective To optimize microwave-assisted extraction of polyphenols from Enteromorpha prolifra. Methods Based on single-factor tests, an efficient microwave-assisted extraction (MAE) technique was developed to extract bioactive polyphenols from E. prolifra through orthogonal L16(4)5 test. Results The highest yield (0.923 ± 0.013) mg/g was obtained when microwave power, solvent to raw material ratio, irradiation time, ethanol concentration, and extraction cycles were 500 W, 25 mL/g, 25 min, 40%, and 3, respectively, which was higher than that of Soxhlet extraction with methanol for 6 h, ultrasound-assisted extraction with 40% ethanol for 1 h twice and heat reflux extraction with 40% ethanol for 2 h twice. Conclusion This finding indicates that MAE is a superior technique for the extraction of polyphenols due to less impurity, higher time efficiency and yield.展开更多
A composite rubber concrete(CRC)was designed by combining waste tire rubber particles with particle sizes of 3~5 mm,1~3 mm and 20 mesh.Taking the rubber content of different particle sizes as the influencing factors,t...A composite rubber concrete(CRC)was designed by combining waste tire rubber particles with particle sizes of 3~5 mm,1~3 mm and 20 mesh.Taking the rubber content of different particle sizes as the influencing factors,the range and variance analysis of the mechanical and impermeability properties of CRC was carried out by orthogonal test.Through analysis,it is concluded that the optimal proportion of 3~5 mm,1~3 mm,and 20 mesh particle size composite rubber is 1:2.5:5.5 kinds of CRC and 3 kinds of ordinary single-mixed rubber concrete(RC)with a total content of 10%~20%were designed under this ratio,and the salt-freezing cycle test was carried out with a concentration of 5%Na 2 SO4 solution.The physical and mechanical damage laws during 120 salt-freezing cycles are obtained,and the corresponding damage prediction model is established according to the experimental data.The results show that:on the one hand,the composite rubber in CRC produces a more uniform“graded”structure,forms a retractable particle group,and reduces the loss of mechanical properties of CRC.On the other hand,colloidal particles with different particle sizes are used as air entraining agent to improve the pore structure of concrete and introduce evenly dispersed bubbles,which fundamentally improves the durability of concrete.Under the experimental conditions,the CRC performance is the best when the overall content of composite rubber is 15%.展开更多
[Objectives] To optimize the pet dog dyeing process of plant hair dye. [Methods]Three factors affecting dyeing were selected including pH,concentration of dye and dyeing time. The L_9(3~3) orthogonal design was used t...[Objectives] To optimize the pet dog dyeing process of plant hair dye. [Methods]Three factors affecting dyeing were selected including pH,concentration of dye and dyeing time. The L_9(3~3) orthogonal design was used to evaluate the hair coloring effect and the absorbance of cleaning solution after hair was dyed. [Results] The optimum pet dog dyeing process of plant hair dye was dye concentration of50 mg/mL,dye pH of 7. 5 and dyeing time of 1 h. [Conclusions] The coloring and fixing effects of the dye and dyeing process are good,which can lay a foundation for the development and utilization of plant dyes.展开更多
[Objectives]To optimize the processing technology for roasted licorice with water.[Methods]Through the orthogonal experimental design,taking the water added,moistening time,frying temperature and frying time as the fa...[Objectives]To optimize the processing technology for roasted licorice with water.[Methods]Through the orthogonal experimental design,taking the water added,moistening time,frying temperature and frying time as the factors,and the content of glycyrrhizin and glycyrrhizic acid as the evaluation index,the processing technology for roasted licorice with water was optimized.[Results]The best processing technology of licorice was as follows:Pure licorice slices were mixed with water and moistened for 3 h,and then fried at 160℃for 6 min.20 kg of water was added to every 100 kg of licorice.[Conclusions]The best processing technology for roasted licorice with water was established,laying a foundation for the research and application of roasted licorice with water and its preparation.展开更多
Railways built in cold,snowy,and lightly populated areas are subjected to wind and snow disasters.In this study,we selected a snow hazard prevention and control section of the Altay–Zhundong Railway in Xinjiang Uygur...Railways built in cold,snowy,and lightly populated areas are subjected to wind and snow disasters.In this study,we selected a snow hazard prevention and control section of the Altay–Zhundong Railway in Xinjiang Uygur Autonomous Region of China as the research object.We investigated the deposited snowfall variation characteristics on the two sides and in the embankment pavement area of snow fences with different porosities,fence heights,and arrangement distances using single-factor tests and orthogonal tests based on global atmospheric reanalysis climate data,field survey data,and a multi-phase flow analysis model.The results showed significant differences in the characteristics of snow cover distribution and snow cover thickness between the embankment and the cutting in the absence of snow protection measures.The maximum snow cover thickness of the embankment pavement decreased by 12.6%relative to the cutting pavement.The snow cover thickness of the embankment exhibited an increasing trend from windward shoulder to leeward shoulder,whereas the snow cover thickness of the cutting presented a declining trend from windward shoulder to leeward toe.In the collaborative prevention and control of snow fences and embankments,the three factors can be ranked in terms of their sensitivity to deposited snowfall within the influence scope of snow fences as follows:fence height>arrangement distance>porosity.At the same time,fence height yielded a significant relationship for the influence scope of snow fences(P<0.05).The three factors can also be ranked in terms of their sensitivity to deposited snowfall on the pavement as follows:porosity>fence height>arrangement distance.For the embankment protection of the Altay–Zhundong Railway against wind and snow,snow fence with a porosity of 75%,a fence height of 4.8 m,and an arrangement distance from the embankment of 60 m produced the best snow control effect.By revealing the characteristics of snow cover distribution along railway subgrade and the protective effect of snow fences,this study provides valuable references for the engineering applications of railway construction in areas prone to wind and snow disasters.展开更多
Methyl anthranilate(MA)is an important material for the synthesis of sodium saccharin,but the yield and quality of MA are not stable due to the batch operation conditions.In this study,the optimum conditions obtained ...Methyl anthranilate(MA)is an important material for the synthesis of sodium saccharin,but the yield and quality of MA are not stable due to the batch operation conditions.In this study,the optimum conditions obtained by an orthogonal test in a batch reactor were a volume ratio of methanol to amide solution of 5:4,volume ratio of sodium hypochlorite to amide solution of 7:4,Hoffmann degradation reaction duration of 10 min,Hoffmann degradation reaction temperature of 10℃,esterification reaction duration of 10 min,and esterification reaction temperature of 40℃.The working flow velocity and allowable working viscosity range of a Venturi ejector inlet were both determined by a computational fluid dynamics(CFD)simulation.Based on the above experimental data,the continuous operation of the process was tested in a three-stage continuous reactor,which improved the product yield and quality of the process.展开更多
The O-ring in the rotary dynamic sealing system of gas meters should have outstanding long-term sealing performance under the conditions of high and low temperature,which can ensure the safety of gas meters.In this pa...The O-ring in the rotary dynamic sealing system of gas meters should have outstanding long-term sealing performance under the conditions of high and low temperature,which can ensure the safety of gas meters.In this paper,based on the O-ring sealing mechanism,taking the compression set as the main sealing index,a finite element simulation method is used to analyze the failure charac-teristics under different conditions according to the constitutive relation of nitrile rubber.Then,using the orthogonal test method for the O-ring sealing performance index,the main factors which affect the law of long-term test are analysed,and the orthogonal regression mathematical model that can predict the compression set is obtained.Finally,the O-ring is improved according to the model,and the test results show that the performance of the new O-rings with high and low temperature resistance is greatly improved and meets the expected target requirements.展开更多
[Objectives]This study was conducted to optimize the Formulation Process of glucosamine chondroitin sulfate tablets. [Methods] The orthogonal design with three levels was carried out with microcrystalline cellulose, c...[Objectives]This study was conducted to optimize the Formulation Process of glucosamine chondroitin sulfate tablets. [Methods] The orthogonal design with three levels was carried out with microcrystalline cellulose, calcium hydrophosphate and cross-linked polyvinylpyrrolidone as three factors to optimize the preparation process. [Results] When microcrystalline cellulose 200 mg/tablet, calcium hydrophosphate 150 mg/tablet, and cross-linked polyvinylpyrrolidone 80 mg/tablet were added, the angle of repose could meet the requirements of tablet pressing, and the dissolution could reach more than 95% in 30 min. The results of the orthogonal test showed that the dissolution effect of self-made tablets was faster than that of commercial products. [Conclusions] The glucosamine hydrochloride chondroitin sulfate tablets prepared by this prescription have better quality.展开更多
[Objectives]To explore the extraction conditions of essential oil from eucalyptus leaves.[Methods]The essential oil of eucalyptus leaves was extracted by steam distillation,and the yields of essential oil from eucalyp...[Objectives]To explore the extraction conditions of essential oil from eucalyptus leaves.[Methods]The essential oil of eucalyptus leaves was extracted by steam distillation,and the yields of essential oil from eucalyptus leaves under different extraction times,soaking times and different solid-liquid ratios were analyzed through orthogonal test with three factors and three variables.[Results]The effects of various factors on extraction results were:distillation time>solid-liquid ratio>soaking time.When the extraction time and soaking time were 1.5 and 2 h,and the solid-liquid ratio of eucalyptus leaves to distilled water was 1:10,the yield of essential oil was the highest(0.8%).The yield of essential oil increased with the increase of extraction and soaking time,but when reaching the optimal value,the yield decreased with the extension of time.Increasing the solid-liquid ratio can improve the yield of essential oil,but beyond a certain value the yield increased gradually while the cost performance decreased.[Conclusions]The results will provide some reference for the recovery and utilization of eucalyptus leaves.展开更多
[Objectives]To optimize the extraction and preparation technology of Wuwei Xiaoke granules.[Methods]Taking the extraction rate of extract as the scoring standard,the water extraction technology was optimized by orthog...[Objectives]To optimize the extraction and preparation technology of Wuwei Xiaoke granules.[Methods]Taking the extraction rate of extract as the scoring standard,the water extraction technology was optimized by orthogonal test.The influence of the proportion of pharmaceutical excipients on the molding conditions of Wuwei Xiaoke granules was investigated using granule molding rate,solubility,moisture,granularity,water-soluble extract and microorganism examination as evaluation indicators,and the optimal molding technology was optimized.[Results]The extraction technology was soaking in water for 0.5 h and heat extraction twice for 1 h each time:adding 10 times the amount of water in the first time,and adding 8 times the amount of water in the second time.The best molding technology was:extract density 1.13-1.16(55-60℃),extract:soluble starch=1:2,and 0.15%stevioside.[Conclusions]The water extraction technology and granule molding technology optimized by orthogonal test are reliable and stable,with good granular characteristics,easy oral administration and good solubility,which can maximize the comprehensive quality of Wuwei Xiaoke granules,and provide an effective reference for the preparation and production of Wuwei Xiaoke granules.展开更多
In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters(i.e. austenitizing temperature and time, and austempering temperature and ti...In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters(i.e. austenitizing temperature and time, and austempering temperature and time) on microstructure and mechanical properties of LZQT500-7 ductile iron dense bars with 172 mm in diameter which were produced by horizontal continuous casting(HCC). The results show that the major factors influencing the hardness of austempered ductile iron(ADI) are austenitizing temperature and austempering temperature. The fraction of retained austenite increases as the austenitizing and austempering temperatures increase. When austenitizing temperature is low, acicular ferrite and retained austenite can be effi ciently obtained by appropriately extending the austenitizing time. The proper austmepering time could ensure enough stability of retained austenite and prevent high carbon austenite decomposition. The optimal mechanical properties of ADI can be achieved with the following process parameters: austenitizing temperature and time are 866 °C and 135 min, and austempering temperature and time are 279 °C and 135 min, respectively. The microstructure of ADI under the optimal austempering process consists of fi ne acicular ferrite and a small amount of retained austenite, and the hardness, tensile strength, yield strength, elongation and impact toughness of the bars are HBW 476, 1670 MPa, 1428 MPa, 2.93% and 25.7 J, respectively.展开更多
Nowadays, a highly integrated valve?controlled cylinder(HIVC) is applied to drive the joints of legged robots. Although the adoption of HIVC has resulted in high?performance robot control, the hydraulic force system s...Nowadays, a highly integrated valve?controlled cylinder(HIVC) is applied to drive the joints of legged robots. Although the adoption of HIVC has resulted in high?performance robot control, the hydraulic force system still has problems, such as strong nonlinearity, and time?varying parameters. This makes HIVC force control very diffcult and complex. How to improve the control performance of the HIVC force control system and find the influence rule of the system parameters on the control performance is very significant. Firstly, the mathematical model of HIVC force control system is established. Then the mathematical expression for parameter sensitivity matrix is obtained by applying matrix sensitivity analysis(PSM). Then, aimed at the sinusoidal response under(three factors and three levels) working conditions, the simulation and the experiment are conducted. While the error between the simulation and experiment can't be avoided. Therefore, combined with the range analysis, the error in the two performance indexes of sinusoidal response under the whole working condition is analyzed. Besides, the sensitivity variation pattern for each system parameter under the whole working condition is figured out. Then the two sensitivity indexes for the three system parameters, which are supply pressure, proportional gain and initial displacement of piston, are proved experimentally. The proposed method significantly reveals the sensitivity characteristics of HIVC force control system, which can make the contribution to improve the control performance.展开更多
The large warping deformation at platform of turbine blade directly affects the forming precision. In the present research, equivalent warping deformation was firstly presented to describe the extent of deformation at...The large warping deformation at platform of turbine blade directly affects the forming precision. In the present research, equivalent warping deformation was firstly presented to describe the extent of deformation at platform. To optimize the process parameters during investment casting to minimize the warping deformation of the platform, based on simulation with Pro CAST, the single factor method, orthogonal test, neural network and genetic algorithm were subsequently used to analyze the influence of pouring temperature, shell mold preheating temperature, furnace temperature and withdrawal velocity on dimensional accuracy of the platform of superalloyDD6 turbine blade. The accuracy of investment casting simulation was verified by measurement of platform at blade casting. The simulation results with the optimal process parameters illustrate that the equivalent warping deformation was dramatically reduced by 21.8% from 0.232295 mm to 0.181698 mm.展开更多
基金Supported by Key Research Project of Wuhan Municipal Health Commission(WZ21A08).
文摘[Objectives]To determine the optimal reflux extraction process conditions for Compound Coptis Ointment.[Methods]The study employed the orthogonal experimental design method and drug-sensitive disc agar diffusion method to evaluate the extraction rate,berberine hydrochloride content,and bacteriostatic ring diameter of the extract as comprehensive indices,and optimized the extraction process conditions of Compound Coptis Ointment using ethanol reflux.[Results]Based on the results of comprehensive indices,the optimal reflux extraction conditions for Compound Coptis Ointment were determined to be soaking in 1.5 times the amount of 70%ethanol for 2 h,followed by two extractions with 6 times the amount of 70%ethanol for 1 h each time.Three verification tests were conducted under the optimal process conditions.The yield of the extract was 28.32%±0.53%,the content of berberine hydrochloride was 4.68%±0.45%,and the diameter of the bacteriostatic ring was(2.5±0.2)cm.[Conclusions]The extract had higher drug content and exhibited better antibacterial effects.The optimized extraction process is simple,stable,and reliable,and can be effectively used to optimize the extraction process of Compound Coptis Ointment.
基金financially supported by the Program for New Century Excellent Talents in University(NCET-12-0849)the Fundamental Research Funds for the Central Universities(13ZD12)the National Natural Science Foundation of China(No.51006034)
文摘To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.
基金Supported by National Science and Technology Supporting Plan (2008BADC4B02)
文摘Biogas is a kind of regenerable energy which is inexpensive and friendly to the environment, but the potential of biogas is difficult to develop fully in China, for most biogas have badly qualities and the utilization of it is monotonous. The suitable operation term about biogas upgrading by pressurized water scrubbing was researched through the orthogonal test in this study. Two sorts of scrubber packing included the random multidimensional hollow sphere packing and the structured screen packing were also used, and the effects of experiment factors included packing, water temperature, gas flow speed, water flow speed and washing pressure were studied. The results showed that better effect was got when the screen structured packing was used; all the five test factors affected the processing significantly in the arrange as before and had better and better significant effects.
文摘Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants mentioned above are installed as four factors,and three levels are selected for every factor.The test is actualized according to L 9(3 4) orthogonal array.Results An optimized recipe A 3 B 3 C 3 D 1 has been obtained after considering multifarious factors such as the resources of these plants and the water-solubility of samples.Conclusion The dry powder insecticide prepared by mixing the plant samples mentioned above as 1∶1∶1mass ratio revealed that insecticidal activities for cickets,grasshopper,aphid,and 3rd instar Mythimna separata walker are significant,respectively.
基金Supported by Traditional Chinese Medicine Science and Technology Development Program of Shandong Province (2017-1982019-0400)Major Science and Technology Innovation Project of Shandong Province (2018CXGC1304)。
文摘[Objectives] This study was conducted to optimize the ethanol extraction technology of monoester alkaloids from Radix Aconiti Preparata. [Methods]On the basis of defined extraction times,ethanol concentration,ethanol times and extraction time were investigated by HPLC-MS combined with orthogonal test to optimize extraction process using the content of monoester alkaloids( the sum of benzoyl neoaconitine,benzoyl hypoaconitine and benzoyl aconitine) as an index.[Results]The optimum ethanol extraction technology was as follows: 75% ethanol,ethanol amount 25 times of the medicinal material,and each extraction for 1. 5 h.[Conclusions] The optimal extraction technology is simple,feasible,stable and reliable. It can provide reference for the industrial production and quality control of monoester alkaloids from Radix Aconiti Preparata.
基金E&T modern center for Natural Products of Liaoning Province of China (2008402021)
文摘Objective To optimize the extract technology of active lignins from the fruits of Schisandra chinensis. Methods The content of schizandrin, gomisin A, and deoxyschizandrin were selected as standards to evaluate the efficiency of smashing tissue extraction (STE). Solid-liquid ratio, extracting times, ethanol concentration, and extracting time were investigated through orthogonal test. Results The optimized conditions for STE were ten times amount of 80% EtOH, extracting for three times, and 2 min for each time. Conclusion STE could obtain relatively higher yield, simplicity of operation, and benefit for environment protection. It could be better choice for the extraction of S. chinensis.
基金National High Technology Development Project (863 project) (2007AA091701)Zhejiang Provincial Natural Science Foundation (Y2080579)Important Project of Zhejiang Ocean University (21135030107)
文摘Objective To optimize microwave-assisted extraction of polyphenols from Enteromorpha prolifra. Methods Based on single-factor tests, an efficient microwave-assisted extraction (MAE) technique was developed to extract bioactive polyphenols from E. prolifra through orthogonal L16(4)5 test. Results The highest yield (0.923 ± 0.013) mg/g was obtained when microwave power, solvent to raw material ratio, irradiation time, ethanol concentration, and extraction cycles were 500 W, 25 mL/g, 25 min, 40%, and 3, respectively, which was higher than that of Soxhlet extraction with methanol for 6 h, ultrasound-assisted extraction with 40% ethanol for 1 h twice and heat reflux extraction with 40% ethanol for 2 h twice. Conclusion This finding indicates that MAE is a superior technique for the extraction of polyphenols due to less impurity, higher time efficiency and yield.
基金supported by the National Key Research and Development Program of China under the Grant No.2018YFC0809400.
文摘A composite rubber concrete(CRC)was designed by combining waste tire rubber particles with particle sizes of 3~5 mm,1~3 mm and 20 mesh.Taking the rubber content of different particle sizes as the influencing factors,the range and variance analysis of the mechanical and impermeability properties of CRC was carried out by orthogonal test.Through analysis,it is concluded that the optimal proportion of 3~5 mm,1~3 mm,and 20 mesh particle size composite rubber is 1:2.5:5.5 kinds of CRC and 3 kinds of ordinary single-mixed rubber concrete(RC)with a total content of 10%~20%were designed under this ratio,and the salt-freezing cycle test was carried out with a concentration of 5%Na 2 SO4 solution.The physical and mechanical damage laws during 120 salt-freezing cycles are obtained,and the corresponding damage prediction model is established according to the experimental data.The results show that:on the one hand,the composite rubber in CRC produces a more uniform“graded”structure,forms a retractable particle group,and reduces the loss of mechanical properties of CRC.On the other hand,colloidal particles with different particle sizes are used as air entraining agent to improve the pore structure of concrete and introduce evenly dispersed bubbles,which fundamentally improves the durability of concrete.Under the experimental conditions,the CRC performance is the best when the overall content of composite rubber is 15%.
基金Supported by the National Science and Technology Foundation Project of Traditional Chinese Veterinary Medicine Resources Rescuing and Organizing(2013FY110600-03)
文摘[Objectives] To optimize the pet dog dyeing process of plant hair dye. [Methods]Three factors affecting dyeing were selected including pH,concentration of dye and dyeing time. The L_9(3~3) orthogonal design was used to evaluate the hair coloring effect and the absorbance of cleaning solution after hair was dyed. [Results] The optimum pet dog dyeing process of plant hair dye was dye concentration of50 mg/mL,dye pH of 7. 5 and dyeing time of 1 h. [Conclusions] The coloring and fixing effects of the dye and dyeing process are good,which can lay a foundation for the development and utilization of plant dyes.
文摘[Objectives]To optimize the processing technology for roasted licorice with water.[Methods]Through the orthogonal experimental design,taking the water added,moistening time,frying temperature and frying time as the factors,and the content of glycyrrhizin and glycyrrhizic acid as the evaluation index,the processing technology for roasted licorice with water was optimized.[Results]The best processing technology of licorice was as follows:Pure licorice slices were mixed with water and moistened for 3 h,and then fried at 160℃for 6 min.20 kg of water was added to every 100 kg of licorice.[Conclusions]The best processing technology for roasted licorice with water was established,laying a foundation for the research and application of roasted licorice with water and its preparation.
基金supported by the National Natural Science Foundation of China(52168065).
文摘Railways built in cold,snowy,and lightly populated areas are subjected to wind and snow disasters.In this study,we selected a snow hazard prevention and control section of the Altay–Zhundong Railway in Xinjiang Uygur Autonomous Region of China as the research object.We investigated the deposited snowfall variation characteristics on the two sides and in the embankment pavement area of snow fences with different porosities,fence heights,and arrangement distances using single-factor tests and orthogonal tests based on global atmospheric reanalysis climate data,field survey data,and a multi-phase flow analysis model.The results showed significant differences in the characteristics of snow cover distribution and snow cover thickness between the embankment and the cutting in the absence of snow protection measures.The maximum snow cover thickness of the embankment pavement decreased by 12.6%relative to the cutting pavement.The snow cover thickness of the embankment exhibited an increasing trend from windward shoulder to leeward shoulder,whereas the snow cover thickness of the cutting presented a declining trend from windward shoulder to leeward toe.In the collaborative prevention and control of snow fences and embankments,the three factors can be ranked in terms of their sensitivity to deposited snowfall within the influence scope of snow fences as follows:fence height>arrangement distance>porosity.At the same time,fence height yielded a significant relationship for the influence scope of snow fences(P<0.05).The three factors can also be ranked in terms of their sensitivity to deposited snowfall on the pavement as follows:porosity>fence height>arrangement distance.For the embankment protection of the Altay–Zhundong Railway against wind and snow,snow fence with a porosity of 75%,a fence height of 4.8 m,and an arrangement distance from the embankment of 60 m produced the best snow control effect.By revealing the characteristics of snow cover distribution along railway subgrade and the protective effect of snow fences,this study provides valuable references for the engineering applications of railway construction in areas prone to wind and snow disasters.
文摘Methyl anthranilate(MA)is an important material for the synthesis of sodium saccharin,but the yield and quality of MA are not stable due to the batch operation conditions.In this study,the optimum conditions obtained by an orthogonal test in a batch reactor were a volume ratio of methanol to amide solution of 5:4,volume ratio of sodium hypochlorite to amide solution of 7:4,Hoffmann degradation reaction duration of 10 min,Hoffmann degradation reaction temperature of 10℃,esterification reaction duration of 10 min,and esterification reaction temperature of 40℃.The working flow velocity and allowable working viscosity range of a Venturi ejector inlet were both determined by a computational fluid dynamics(CFD)simulation.Based on the above experimental data,the continuous operation of the process was tested in a three-stage continuous reactor,which improved the product yield and quality of the process.
基金Supported by the National Key Research and Development Program of China(No.2018YFC0808902).
文摘The O-ring in the rotary dynamic sealing system of gas meters should have outstanding long-term sealing performance under the conditions of high and low temperature,which can ensure the safety of gas meters.In this paper,based on the O-ring sealing mechanism,taking the compression set as the main sealing index,a finite element simulation method is used to analyze the failure charac-teristics under different conditions according to the constitutive relation of nitrile rubber.Then,using the orthogonal test method for the O-ring sealing performance index,the main factors which affect the law of long-term test are analysed,and the orthogonal regression mathematical model that can predict the compression set is obtained.Finally,the O-ring is improved according to the model,and the test results show that the performance of the new O-rings with high and low temperature resistance is greatly improved and meets the expected target requirements.
基金Supported by School-level High-level Talent Project (XGY2021A022)Doctoral Research Startup Fund of Department of Science&Technology of Liaoning Province (2021-BS-252)。
文摘[Objectives]This study was conducted to optimize the Formulation Process of glucosamine chondroitin sulfate tablets. [Methods] The orthogonal design with three levels was carried out with microcrystalline cellulose, calcium hydrophosphate and cross-linked polyvinylpyrrolidone as three factors to optimize the preparation process. [Results] When microcrystalline cellulose 200 mg/tablet, calcium hydrophosphate 150 mg/tablet, and cross-linked polyvinylpyrrolidone 80 mg/tablet were added, the angle of repose could meet the requirements of tablet pressing, and the dissolution could reach more than 95% in 30 min. The results of the orthogonal test showed that the dissolution effect of self-made tablets was faster than that of commercial products. [Conclusions] The glucosamine hydrochloride chondroitin sulfate tablets prepared by this prescription have better quality.
基金Supported by Doctoral Start-up Fund of Guangxi Minzu Normal University(2021 BS003).
文摘[Objectives]To explore the extraction conditions of essential oil from eucalyptus leaves.[Methods]The essential oil of eucalyptus leaves was extracted by steam distillation,and the yields of essential oil from eucalyptus leaves under different extraction times,soaking times and different solid-liquid ratios were analyzed through orthogonal test with three factors and three variables.[Results]The effects of various factors on extraction results were:distillation time>solid-liquid ratio>soaking time.When the extraction time and soaking time were 1.5 and 2 h,and the solid-liquid ratio of eucalyptus leaves to distilled water was 1:10,the yield of essential oil was the highest(0.8%).The yield of essential oil increased with the increase of extraction and soaking time,but when reaching the optimal value,the yield decreased with the extension of time.Increasing the solid-liquid ratio can improve the yield of essential oil,but beyond a certain value the yield increased gradually while the cost performance decreased.[Conclusions]The results will provide some reference for the recovery and utilization of eucalyptus leaves.
基金Supported by Self-funded Research Project of Traditional Chinese Medicine Administration of Guangxi Zhuang Autonomous Region(GXZYZ20210313)National TCM Characteristic Technology Inheritance Talent Training Program(GZYYBRJF[2014]39).
文摘[Objectives]To optimize the extraction and preparation technology of Wuwei Xiaoke granules.[Methods]Taking the extraction rate of extract as the scoring standard,the water extraction technology was optimized by orthogonal test.The influence of the proportion of pharmaceutical excipients on the molding conditions of Wuwei Xiaoke granules was investigated using granule molding rate,solubility,moisture,granularity,water-soluble extract and microorganism examination as evaluation indicators,and the optimal molding technology was optimized.[Results]The extraction technology was soaking in water for 0.5 h and heat extraction twice for 1 h each time:adding 10 times the amount of water in the first time,and adding 8 times the amount of water in the second time.The best molding technology was:extract density 1.13-1.16(55-60℃),extract:soluble starch=1:2,and 0.15%stevioside.[Conclusions]The water extraction technology and granule molding technology optimized by orthogonal test are reliable and stable,with good granular characteristics,easy oral administration and good solubility,which can maximize the comprehensive quality of Wuwei Xiaoke granules,and provide an effective reference for the preparation and production of Wuwei Xiaoke granules.
基金financially supported by the fund of the Key Projects of Shaanxi Provincial International Technology Cooperation Plan(2013KW16)the Scientific Research Program funded by Shaanxi Provincial Education Department(2013JK0914)+2 种基金the State Key Laboratory of Solidifi cation Processing in NWPU(SKLSP201115)the Scientific Research Project of Xi'an University of Technology(2013CX004)the fund of the Key Laboratory of Electrical Materials and Infi ltration Technology of Shaanxi Province,China(2014)
文摘In the present research, the orthogonal experiment was carried out to investigate the influence of different austempering process parameters(i.e. austenitizing temperature and time, and austempering temperature and time) on microstructure and mechanical properties of LZQT500-7 ductile iron dense bars with 172 mm in diameter which were produced by horizontal continuous casting(HCC). The results show that the major factors influencing the hardness of austempered ductile iron(ADI) are austenitizing temperature and austempering temperature. The fraction of retained austenite increases as the austenitizing and austempering temperatures increase. When austenitizing temperature is low, acicular ferrite and retained austenite can be effi ciently obtained by appropriately extending the austenitizing time. The proper austmepering time could ensure enough stability of retained austenite and prevent high carbon austenite decomposition. The optimal mechanical properties of ADI can be achieved with the following process parameters: austenitizing temperature and time are 866 °C and 135 min, and austempering temperature and time are 279 °C and 135 min, respectively. The microstructure of ADI under the optimal austempering process consists of fi ne acicular ferrite and a small amount of retained austenite, and the hardness, tensile strength, yield strength, elongation and impact toughness of the bars are HBW 476, 1670 MPa, 1428 MPa, 2.93% and 25.7 J, respectively.
基金Supported by National Natural Science Foundation of China(Grant No.51605417)Key Project of Hebei Provincial Natural Science Foundation,China(Grant No.E2016203264)State Key Laboratory of Fluid Power and Mechatronic Systems(Zhejiang University)Open Fund Project(Grant No.GZKF-201502)
文摘Nowadays, a highly integrated valve?controlled cylinder(HIVC) is applied to drive the joints of legged robots. Although the adoption of HIVC has resulted in high?performance robot control, the hydraulic force system still has problems, such as strong nonlinearity, and time?varying parameters. This makes HIVC force control very diffcult and complex. How to improve the control performance of the HIVC force control system and find the influence rule of the system parameters on the control performance is very significant. Firstly, the mathematical model of HIVC force control system is established. Then the mathematical expression for parameter sensitivity matrix is obtained by applying matrix sensitivity analysis(PSM). Then, aimed at the sinusoidal response under(three factors and three levels) working conditions, the simulation and the experiment are conducted. While the error between the simulation and experiment can't be avoided. Therefore, combined with the range analysis, the error in the two performance indexes of sinusoidal response under the whole working condition is analyzed. Besides, the sensitivity variation pattern for each system parameter under the whole working condition is figured out. Then the two sensitivity indexes for the three system parameters, which are supply pressure, proportional gain and initial displacement of piston, are proved experimentally. The proposed method significantly reveals the sensitivity characteristics of HIVC force control system, which can make the contribution to improve the control performance.
基金financially supported by the National Natural Science Foundation of China(No.51371152)
文摘The large warping deformation at platform of turbine blade directly affects the forming precision. In the present research, equivalent warping deformation was firstly presented to describe the extent of deformation at platform. To optimize the process parameters during investment casting to minimize the warping deformation of the platform, based on simulation with Pro CAST, the single factor method, orthogonal test, neural network and genetic algorithm were subsequently used to analyze the influence of pouring temperature, shell mold preheating temperature, furnace temperature and withdrawal velocity on dimensional accuracy of the platform of superalloyDD6 turbine blade. The accuracy of investment casting simulation was verified by measurement of platform at blade casting. The simulation results with the optimal process parameters illustrate that the equivalent warping deformation was dramatically reduced by 21.8% from 0.232295 mm to 0.181698 mm.
