Weak signal reception is a very important and challenging problem for communication systems especially in the presence of non-Gaussian noise,and in which case the performance of optimal linear correlated receiver degr...Weak signal reception is a very important and challenging problem for communication systems especially in the presence of non-Gaussian noise,and in which case the performance of optimal linear correlated receiver degrades dramatically.Aiming at this,a novel uncorrelated reception scheme based on adaptive bistable stochastic resonance(ABSR)for a weak signal in additive Laplacian noise is investigated.By analyzing the key issue that the quantitative cooperative resonance matching relationship between the characteristics of the noisy signal and the nonlinear bistable system,an analytical expression of the bistable system parameters is derived.On this basis,by means of bistable system parameters self-adaptive adjustment,the counterintuitive stochastic resonance(SR)phenomenon can be easily generated at which the random noise is changed into a benefit to assist signal transmission.Finally,it is demonstrated that approximately 8dB bit error ratio(BER)performance improvement for the ABSR-based uncorrelated receiver when compared with the traditional uncorrelated receiver at low signal to noise ratio(SNR)conditions varying from-30dB to-5dB.展开更多
The weak signal detection method based on stochastic resonance is usually used to extract and identify the weak characteristic signal submerged in strong noise by using the noise energy transfer mechanism.We propose a...The weak signal detection method based on stochastic resonance is usually used to extract and identify the weak characteristic signal submerged in strong noise by using the noise energy transfer mechanism.We propose a novel composite multistable stochastic-resonance(NCMSR)model combining the Gaussian potential model and an improved bistable model.Compared with the traditional multistable stochastic resonance method,all the parameters in the novel model have no symmetry,the output signal-to-noise ratio can be optimized and the output amplitude can be improved by adjusting the system parameters.The model retains the advantages of continuity and constraint of the Gaussian potential model and the advantages of the improved bistable model without output saturation,the NCMSR model has a higher utilization of noise.Taking the output signal-to-noise ratio as the index,weak periodic signal is detected based on the NCMSR model in Gaussian noise andαnoise environment respectively,and the detection effect is good.The application of NCMSR to the actual detection of bearing fault signals can realize the fault detection of bearing inner race and outer race.The outstanding advantages of this method in weak signal detection are verified,which provides a theoretical basis for industrial practical applications.展开更多
Aiming at the problem that indoor positioning technology based on wireless ultra-wideband pulse technology is susceptible to non-line-of-sight effects and multipath effects in confined spaces and weak signal environme...Aiming at the problem that indoor positioning technology based on wireless ultra-wideband pulse technology is susceptible to non-line-of-sight effects and multipath effects in confined spaces and weak signal environments,a high-precision positioning system based on UWB and IMU in a confined environment is designed.The STM32 chip is used as the main control,and the data information of IMU and UWB is fused by the fusion filtering algorithm.Finally,the real-time information of the positioning is transmitted to the host computer and the cloud.The experimental results show that the positioning accuracy and positioning stability of the system have been improved in the non-line-of-sight case of closed environment.The system has high positioning accuracy in a closed environment,and the components used are consumer-grade,which has strong practicability.展开更多
The traditional methods of weak harmonic signal detection under strong chaotic interference often suffer from high computational complexity and poor performance. In this paper, an Extended Kalman Filter (EKF) based de...The traditional methods of weak harmonic signal detection under strong chaotic interference often suffer from high computational complexity and poor performance. In this paper, an Extended Kalman Filter (EKF) based detection method is proposed for the detection of weak harmonic signal. The EKF method avoids matrix inversion by iterating measurement equation and state equation, which simultaneously improves the robustness and reduces the complexity. Compared with the existing detection methods, the proposed method has the following advantages: 1) it has better performance than the neural network method;2) it has similar performance with the optimal filtering method, but with lower computational complexity;3) it is more robust compared with the optimal filtering method.展开更多
Navigation and positioning in harsh environments is still a great challenge for many applications. Collective Detection (CD) is a powerful approach for acquiring highly attenuated satellite signals in challenging envi...Navigation and positioning in harsh environments is still a great challenge for many applications. Collective Detection (CD) is a powerful approach for acquiring highly attenuated satellite signals in challenging environments, because of its capacity to process all visible satellites collectively taking advantage of the spatial correlation between GNSS signals as a vector acquisition scheme. CD combines the correlator outputs of satellite channels and projects them onto the position/clock bias domain in order to enhance the overall GNSS signal detection probability. In CD, the code phase search for all satellites in view is mapped into a receiver position/clock bias grid and the satellite signals are not acquired individually but collectively. In this concept, a priori knowledge of satellite ephemeris and reference location are provided to the user. Furthermore, CD addresses some of the inherent drawbacks of the conventional acquisition at the expenses of an increased computational cost. CD techniques are computationally intensive because of the significant number of candidate points in the position-time domain. The aim of this paper is to describe the operation of the CD approach incorporating new methods and architectures to address both the complexity and sensitivity problems. The first method consists of hybridizing the collective detection approach with some correlation techniques and coupling it with a better technique for Doppler frequency estimate. For that, a new scheme with less calculation load is proposed in order to accelerate the detection and location process. Then, high sensitivity acquisition techniques using long coherent integration and non-coherent integration are used in order to improve the performance of the CD algorithm.展开更多
It is difficult to achieve accurate acquisition of weak global positioning system( GPS) signals with traditional methods. A weak signal acquisition strategy based on block processing and differentially coherent( BPDC)...It is difficult to achieve accurate acquisition of weak global positioning system( GPS) signals with traditional methods. A weak signal acquisition strategy based on block processing and differentially coherent( BPDC) is put forward after analyzing the advantages and disadvantages of coherent and non-coherent integration algorithms. Code phase parallel search of the pre-coherent integration is conducted by using fast Fourier transform( FFT),and the results are then differential coherent processed and block processed. BPDC method reduces computation cost compared with coherent and noncoherent( CNC) algorithm. The performance of the two algorithms is also compared based on simulated signals. The result shows that the noise suppression effect of BPDC algorithms is superior to that of traditional CNC algorithm,and the superiority of BPDC is more apparent with the reduction of carrier to noise ratio( CNR). In the case that the pre-coherent integration length is 4 ms and CNR is reduced to 28 dB-Hz,CNC algorithm cannot yet acquire signal correctly while BPDC has well acquisition performance. Therefore,for weak GPS signal acquisition,BPDC algorithm can acquire the signal with lower CNR and has better acquisition property.展开更多
In order to solve the parameter adjustment problems of adaptive stochastic resonance system in the areas of weak signal detection,this article presents a new method to enhance the detection efficiency and availability...In order to solve the parameter adjustment problems of adaptive stochastic resonance system in the areas of weak signal detection,this article presents a new method to enhance the detection efficiency and availability in the system of two-dimensional Duffing based on particle swarm optimization.First,the influence of different parameters on the detection performance is analyzed respectively.The correlation between parameter adjustment and stochastic resonance effect is also discussed and converted to the problem of multi-parameter optimization.Second,the experiments including typical system and sea clutter data are conducted to verify the effect of the proposed method.Results show that the proposed method is highly effective to detect weak signal from chaotic background,and enhance the output SNR greatly.展开更多
To acquire global navigation satellite system(GNSS)signals means four-dimension acquisition of bit transition,Doppler frequency,Doppler rate,and code phase in high-dynamic and weak signal environments,which needs a hi...To acquire global navigation satellite system(GNSS)signals means four-dimension acquisition of bit transition,Doppler frequency,Doppler rate,and code phase in high-dynamic and weak signal environments,which needs a high computational cost.To reduce the computations,this paper proposes a twostep compressed acquisition method(TCAM)for the post-correlation signal parameters estimation.Compared with the fast Fourier transform(FFT)based methods,TCAM uses fewer frequency search points.In this way,the proposed method reduces complex multiplications,and uses real multiplications instead of improving the accuracy of the Doppler frequency and the Doppler rate.Furthermore,the differential process between two adjacent milliseconds is used for avoiding the impact of bit transition and the Doppler frequency on the integration peak.The results demonstrate that due to the reduction of complex multiplications,the computational cost of TCAM is lower than that of the FFT based method under the same signal to noise ratio(SNR).展开更多
Stochastic resonance(SR) has been proved to be an effective approach to extract weak signals overwhelmed in noise.However, the detection effect of current SR models is still unsatisfactory. Here, a coupled tri-stable ...Stochastic resonance(SR) has been proved to be an effective approach to extract weak signals overwhelmed in noise.However, the detection effect of current SR models is still unsatisfactory. Here, a coupled tri-stable stochastic resonance(CTSSR) model is proposed to further increase the output signal-to-noise ratio(SNR) and improve the detection effect of SR. The effects of parameters a, b, c, and r in the proposed resonance system on the SNR are studied, by which we determine a set of parameters that is relatively optimal to implement a comparison with other classical SR models.Numerical experiment results indicate that this proposed model performs better in weak signal detection applications than the classical ones with merits of higher output SNR and better anti-noise capability.展开更多
Weak global navigation satellite system(GNSS) signal acquisition has been a limitation for high sensitivity GPS receivers. This paper modifies the traditional acquisition algorithms and proposes a new weak GNSS signal...Weak global navigation satellite system(GNSS) signal acquisition has been a limitation for high sensitivity GPS receivers. This paper modifies the traditional acquisition algorithms and proposes a new weak GNSS signal acquisition method using re-scaling and adaptive stochastic resonance(SR). The adoption of classical SR is limited to low-frequency and periodic signals. Given that GNSS signal frequency is high and that the periodic feature of the GNSS signal is affected by the Doppler frequency shift, classical SR methods cannot be directly used to acquire GNSS signals. Therefore, the re-scaling technique is used in our study to expand its usage to high-frequency signals and adaptive control technique is used to gradually determine the Doppler shift effect in GNSS signal buried in strong noises. The effectiveness of our proposed method was verified by the simulations on GPS L1 signals. The simulation results indicate that the new algorithm based on SR can reach-181 d BW sensitivity with a very short data length of 1 ms.展开更多
The conventional Duffing oscillator weak signal detection method, which is based on a strong reference signal, has inherent deficiencies. To address these issues, the characteristics of the Duffing oscillator's ph...The conventional Duffing oscillator weak signal detection method, which is based on a strong reference signal, has inherent deficiencies. To address these issues, the characteristics of the Duffing oscillator's phase trajectory in a smallscale periodic state are analyzed by introducing the theory of stopping oscillation system. Based on this approach, a novel Duffing oscillator weak wide-band signal detection method is proposed. In this novel method, the reference signal is discarded, and the to-be-detected signal is directly used as a driving force. By calculating the cosine function of a phase space angle, a single Duffing oscillator can be used for weak wide-band signal detection instead of an array of uncoupled Duffing oscillators. Simulation results indicate that, compared with the conventional Duffing oscillator detection method,this approach performs better in frequency detection intervals, and reduces the signal-to-noise ratio detection threshold,while improving the real-time performance of the system.展开更多
In the infrared spectrum absorbed type gas concentration sensor,voltage signal obtained from the two-channel thermopile infrared detector TPS2534 is very weak.In order to solve this problem,the authors have establishe...In the infrared spectrum absorbed type gas concentration sensor,voltage signal obtained from the two-channel thermopile infrared detector TPS2534 is very weak.In order to solve this problem,the authors have established the structure of the sensor and designed weak signal detecting circuit of the sensor based on infrared spectrum absorption principle,differential de-noising principle and weak signal detecting principle.The authors have made experiments using CH4 gas.The results show that the circuit can remove noise effectively and detect weak electrical signal obtained from the detector.展开更多
Vehicle positioning with the global navigation satellite system(GNSS) in urban environments faces two problems which are attenuation and dynamic.For traditional GNSS receivers hardly able to track dynamic weak signals...Vehicle positioning with the global navigation satellite system(GNSS) in urban environments faces two problems which are attenuation and dynamic.For traditional GNSS receivers hardly able to track dynamic weak signals,the coupling between all visible satellite signals is ignored in the absence of navigation state feedback,and thermal noise error and dynamic stress threshold are contradictory due to non-coherent discriminators.The vector delay/frequency locked loop(VDFLL) with navigation state feedback and the joint vector tracking loop(JVTL) with coherent discriminator which is a synchronization parameter tracking loop based on maximum likelihood estimation(MLE) are proposed to improve the tracking sensitivity of GNSS receiver in dynamic weak signal environments.A joint vector position tracking loop(JVPTL) directly tracking user position and velocity is proposed to further improve tracking sensitivity.The coherent navigation parameter discriminator of JVPTL,being able to ease the contradiction between thermal noise error and dynamic stress threshold,is based on MLE according to the navigation parameter based linear model of received baseband signals.Simulation results show that JVPTL,which combines the advantages of both VDFLL and JVTL,performs better than both VDFLL and JVTL in dynamic weak signal environments.展开更多
Based on the data synthesis simulation and the actual processing of the airgun seismic source signal,three quantitative indicators of signal-to-noise ratio,waveform correlation coefficient and phase offset,are superim...Based on the data synthesis simulation and the actual processing of the airgun seismic source signal,three quantitative indicators of signal-to-noise ratio,waveform correlation coefficient and phase offset,are superimposed. We systematically evaluate the functions of the following three stack methods including linearity,phase weighting and S-transform in the extraction of weak signals under strong background noise and quantitatively estimate the reliability of the stack results. Through the comprehensive discussion of the above three methods of stack results,the preliminary comparative analysis believes that the linear stack signal-to-noise ratio is low,but the waveform distortion is minimal; the phase-weighted superimposed signal-to-noise ratio is high and the phase offset is small,but the results of the waveform quality and linear stack are larger than the deviation; the S-transform stack has a relatively higher signal-to-noise ratio and a small loss of waveform amplitude,but there is a certain phase shift phenomenon. It is therefore suggested that linear stack technology should be used when the requirements of both waveform quality and time precision are high. However,the selection of the stack method when the airgun source excitation is limited should be emphasized. If high fidelity is required, the S-transform stack method should be selected; if the required time is high,accuracy can be selected by phase-weighted stack method to achieve reasonable extraction of weak signals.展开更多
We propose a joint exponential function and Woods–Saxon stochastic resonance(EWSSR)model.Because change of a single parameter in the classical stochastic resonance model may cause a great change in the shape of the p...We propose a joint exponential function and Woods–Saxon stochastic resonance(EWSSR)model.Because change of a single parameter in the classical stochastic resonance model may cause a great change in the shape of the potential function,it is difficult to obtain the optimal output signal-to-noise ratio by adjusting one parameter.In the novel system,the influence of different parameters on the shape of the potential function has its own emphasis,making it easier for us to adjust the shape of the potential function.The system can obtain different widths of the potential well or barrier height by adjusting one of these parameters,so that the system can match different types of input signals adaptively.By adjusting the system parameters,the potential function model can be transformed between the bistable model and the monostable model.The potential function of EWSSR has richer shapes and geometric characteristics.The effects of parameters,such as the height of the barrier and the width of the potential well,on SNR are studied,and a set of relatively optimal parameters are determined.Moreover,the EWSSR model is compared with other classical stochastic resonance models.Numerical experiments show that the proposed EWSSR model has higher SNR and better noise immunity than other classical stochastic resonance models.Simultaneously,the EWSSR model is applied to the detection of actual bearing fault signals,and the detection effect is also superior to other models.展开更多
Based on the asymptotic spectral distribution of Wigner matrices,a new normality test method is proposed via reforming the white noise sequence.In this work,the asymptotic cumulative distribution function(CDF)of eigen...Based on the asymptotic spectral distribution of Wigner matrices,a new normality test method is proposed via reforming the white noise sequence.In this work,the asymptotic cumulative distribution function(CDF)of eigenvalues of the Wigner matrix is deduced.A numerical Kullback-Leibler divergence of the empirical spectral CDF based on test samples from the deduced asymptotic CDF is established,which is treated as the test statistic.For validating the superiority of our proposed normality test,we apply the method to weak 8PSK signal detection in the single-input single-output(SISO) system and the single-input multiple-output(SIMO)system.By comparing with other common normality tests and the existing signal detection methods,simulation results show that the proposed method is superior and robust.展开更多
In this paper,the data wipe-off(DWO)algorithm is incorporated into the vector tracking loop of the Global Positioning System(GPS)receiver for improving signal tracking performance.The navigation data,which contains in...In this paper,the data wipe-off(DWO)algorithm is incorporated into the vector tracking loop of the Global Positioning System(GPS)receiver for improving signal tracking performance.The navigation data,which contains information that is necessary to perform navigation computations,are binary phase-shift keying(BPSK)modulated onto the GPS carrier phase with the bit duration of 20 ms(i.e.,50 bits per second).To continuously track the satellite’s signal in weak signal environment,the DWO algorithm on the basis of pre-detection method is adopted to detect data bit sign reversal every 20 ms.Tracking accuracy of a weak GPS signal is decreased by possible data bit sign reversal every 20 ms to the predetection integration time(PIT)or integration interval.To achieve better tracking performance in weak signal environment,the coherent integration interval can be extended.However,increase of the integration interval lead to decrease of the tracking accuracy by possible data bit sign reversal every 20 ms to the integration interval.When the integration interval of the correlator is extended over 20 ms in low C/No levels,the navigation DWO algorithm can be employed to avoid energy loss due to bit transitions.The method presented in this paper has an advantage to continuously estimate the navigation data bit and achieve improved tracking performance.Evaluation of the tracking performance based on the various integration intervals for the vector tracking loop of a GPS receiver will be presented.展开更多
New positioning applications’ availability requirements demand receivers with higher sensitivities and ability to process multiple GNSS signals. Possible applications include acquiring one signal per GNSS constellati...New positioning applications’ availability requirements demand receivers with higher sensitivities and ability to process multiple GNSS signals. Possible applications include acquiring one signal per GNSS constellation in the same frequency band and combining them for increased sensitivity or predicting acquisition of other signals. Frequency domain processing can be used for this purpose, since it benefits from parallel processing capabilities of Fast Fourier Transform (FFT), which can be efficiently implemented in software receivers. On the other hand, long coherent integration times are mainly limited due to large FFT size in receivers using frequency domain techniques. A new method is proposed to address the problems in frequency domain receivers without compromising the resources and execution time. A pre-correlation accumulation (PCA) is proposed to partition the received samples into one-code-period blocks, and to sum them together. As a result, the noise is averaged out and the correlation results will gain more power, provided that the relative phase between the data segments is compensated for. In addition to simplicity, the proposed PCA method enables the use of one-size FFT for all integration times. A post-correlation peak combination is also proposed to remove the need for double buffering. The proposed methods are implemented in a configurable Simulink model, developed for acquiring recorded GNSS signals. For weak signal scenarios, a Spirent GPS simulator is used as a source. Acquisition results for GPS L1 C/A and GLONASS L1OF are shown and the performance of the proposed technique is discussed. The proposed techniques target GNSS receivers using frequency domain processing aiming at accommodating all the GNSS signals, while minimizing resource usage. They also apply to weak signal acquisition in frequency domain to answer the availability demand of today’s GNSS positioning applications.展开更多
Waveforms generated by the 50t explosion of project Brightlight(Ⅰ) were recorded by HILR array.Using array techniques,the author performed identification,f-k analysis,velocity spectrum analysis,etc.of the weak signal...Waveforms generated by the 50t explosion of project Brightlight(Ⅰ) were recorded by HILR array.Using array techniques,the author performed identification,f-k analysis,velocity spectrum analysis,etc.of the weak signals.The analysis results show that the signal-to-noise ratio after beamforming was obviously enhanced,and the signal could be clearly shown.The energy from this explosion was mainly concentrated in the 1 ～ 8Hz range from f-k analysis.The velocity spectrum gave clear positions of event phases,which could not be seen in the original weak signals.The maximum energy distribution obtained by the Beaman method is close to the theoretical value in the azimuth-slowness domain.展开更多
基金supported in part by the National Natural Science Foundation of China(62001356)in part by the National Natural Science Foundation for Distinguished Young Scholar(61825104)+1 种基金in part by the National Key Research and Development Program of China(2022YFC3301300)in part by the Innovative Research Groups of the National Natural Science Foundation of China(62121001)。
文摘Weak signal reception is a very important and challenging problem for communication systems especially in the presence of non-Gaussian noise,and in which case the performance of optimal linear correlated receiver degrades dramatically.Aiming at this,a novel uncorrelated reception scheme based on adaptive bistable stochastic resonance(ABSR)for a weak signal in additive Laplacian noise is investigated.By analyzing the key issue that the quantitative cooperative resonance matching relationship between the characteristics of the noisy signal and the nonlinear bistable system,an analytical expression of the bistable system parameters is derived.On this basis,by means of bistable system parameters self-adaptive adjustment,the counterintuitive stochastic resonance(SR)phenomenon can be easily generated at which the random noise is changed into a benefit to assist signal transmission.Finally,it is demonstrated that approximately 8dB bit error ratio(BER)performance improvement for the ABSR-based uncorrelated receiver when compared with the traditional uncorrelated receiver at low signal to noise ratio(SNR)conditions varying from-30dB to-5dB.
基金the National Natural Science Foundation of China(Grant No.61871318)the Key Research and Development Projects in Shaanxi Province(Grant No.2023YBGY-044)the Key Laboratory System Control and Intelligent Information Processing(Grant No.2020CP10)。
文摘The weak signal detection method based on stochastic resonance is usually used to extract and identify the weak characteristic signal submerged in strong noise by using the noise energy transfer mechanism.We propose a novel composite multistable stochastic-resonance(NCMSR)model combining the Gaussian potential model and an improved bistable model.Compared with the traditional multistable stochastic resonance method,all the parameters in the novel model have no symmetry,the output signal-to-noise ratio can be optimized and the output amplitude can be improved by adjusting the system parameters.The model retains the advantages of continuity and constraint of the Gaussian potential model and the advantages of the improved bistable model without output saturation,the NCMSR model has a higher utilization of noise.Taking the output signal-to-noise ratio as the index,weak periodic signal is detected based on the NCMSR model in Gaussian noise andαnoise environment respectively,and the detection effect is good.The application of NCMSR to the actual detection of bearing fault signals can realize the fault detection of bearing inner race and outer race.The outstanding advantages of this method in weak signal detection are verified,which provides a theoretical basis for industrial practical applications.
文摘Aiming at the problem that indoor positioning technology based on wireless ultra-wideband pulse technology is susceptible to non-line-of-sight effects and multipath effects in confined spaces and weak signal environments,a high-precision positioning system based on UWB and IMU in a confined environment is designed.The STM32 chip is used as the main control,and the data information of IMU and UWB is fused by the fusion filtering algorithm.Finally,the real-time information of the positioning is transmitted to the host computer and the cloud.The experimental results show that the positioning accuracy and positioning stability of the system have been improved in the non-line-of-sight case of closed environment.The system has high positioning accuracy in a closed environment,and the components used are consumer-grade,which has strong practicability.
基金the National Natural Science Foundation of China (Grant No. 61871102 and 61731006)Sichuan province science and technology support program under Grant N0. 2017GZ0345.
文摘The traditional methods of weak harmonic signal detection under strong chaotic interference often suffer from high computational complexity and poor performance. In this paper, an Extended Kalman Filter (EKF) based detection method is proposed for the detection of weak harmonic signal. The EKF method avoids matrix inversion by iterating measurement equation and state equation, which simultaneously improves the robustness and reduces the complexity. Compared with the existing detection methods, the proposed method has the following advantages: 1) it has better performance than the neural network method;2) it has similar performance with the optimal filtering method, but with lower computational complexity;3) it is more robust compared with the optimal filtering method.
文摘Navigation and positioning in harsh environments is still a great challenge for many applications. Collective Detection (CD) is a powerful approach for acquiring highly attenuated satellite signals in challenging environments, because of its capacity to process all visible satellites collectively taking advantage of the spatial correlation between GNSS signals as a vector acquisition scheme. CD combines the correlator outputs of satellite channels and projects them onto the position/clock bias domain in order to enhance the overall GNSS signal detection probability. In CD, the code phase search for all satellites in view is mapped into a receiver position/clock bias grid and the satellite signals are not acquired individually but collectively. In this concept, a priori knowledge of satellite ephemeris and reference location are provided to the user. Furthermore, CD addresses some of the inherent drawbacks of the conventional acquisition at the expenses of an increased computational cost. CD techniques are computationally intensive because of the significant number of candidate points in the position-time domain. The aim of this paper is to describe the operation of the CD approach incorporating new methods and architectures to address both the complexity and sensitivity problems. The first method consists of hybridizing the collective detection approach with some correlation techniques and coupling it with a better technique for Doppler frequency estimate. For that, a new scheme with less calculation load is proposed in order to accelerate the detection and location process. Then, high sensitivity acquisition techniques using long coherent integration and non-coherent integration are used in order to improve the performance of the CD algorithm.
基金Supported by the Fundamental Research Fund for the Central University(1002-56XAA13016)
文摘It is difficult to achieve accurate acquisition of weak global positioning system( GPS) signals with traditional methods. A weak signal acquisition strategy based on block processing and differentially coherent( BPDC) is put forward after analyzing the advantages and disadvantages of coherent and non-coherent integration algorithms. Code phase parallel search of the pre-coherent integration is conducted by using fast Fourier transform( FFT),and the results are then differential coherent processed and block processed. BPDC method reduces computation cost compared with coherent and noncoherent( CNC) algorithm. The performance of the two algorithms is also compared based on simulated signals. The result shows that the noise suppression effect of BPDC algorithms is superior to that of traditional CNC algorithm,and the superiority of BPDC is more apparent with the reduction of carrier to noise ratio( CNR). In the case that the pre-coherent integration length is 4 ms and CNR is reduced to 28 dB-Hz,CNC algorithm cannot yet acquire signal correctly while BPDC has well acquisition performance. Therefore,for weak GPS signal acquisition,BPDC algorithm can acquire the signal with lower CNR and has better acquisition property.
基金supported by the National Natural Science Foundation of China ( Grant No. 61072133)the Production,Learning and Research Joint Innovation Program of Jiangsu Province, China ( Grant Nos. BY2013007-02, SBY201120033)+2 种基金the Major Project Plan for Natural science Research in Colleges and Universities of Jiangsu Province, China( Grant No. 15KJA460008)the Open Topic of Atmospheric Sounding Key Open Laboratory of China Meteorological Administration ( Grant No. KLAS201407)the advantage discipline platform " Information and Communication Engineering" of Jiangsu Province,China
文摘In order to solve the parameter adjustment problems of adaptive stochastic resonance system in the areas of weak signal detection,this article presents a new method to enhance the detection efficiency and availability in the system of two-dimensional Duffing based on particle swarm optimization.First,the influence of different parameters on the detection performance is analyzed respectively.The correlation between parameter adjustment and stochastic resonance effect is also discussed and converted to the problem of multi-parameter optimization.Second,the experiments including typical system and sea clutter data are conducted to verify the effect of the proposed method.Results show that the proposed method is highly effective to detect weak signal from chaotic background,and enhance the output SNR greatly.
基金supported by the National Natural Science Foundation of China(61901154,41704154)Zhejiang Province Science Foundation for Youths(LQ19F010006).
文摘To acquire global navigation satellite system(GNSS)signals means four-dimension acquisition of bit transition,Doppler frequency,Doppler rate,and code phase in high-dynamic and weak signal environments,which needs a high computational cost.To reduce the computations,this paper proposes a twostep compressed acquisition method(TCAM)for the post-correlation signal parameters estimation.Compared with the fast Fourier transform(FFT)based methods,TCAM uses fewer frequency search points.In this way,the proposed method reduces complex multiplications,and uses real multiplications instead of improving the accuracy of the Doppler frequency and the Doppler rate.Furthermore,the differential process between two adjacent milliseconds is used for avoiding the impact of bit transition and the Doppler frequency on the integration peak.The results demonstrate that due to the reduction of complex multiplications,the computational cost of TCAM is lower than that of the FFT based method under the same signal to noise ratio(SNR).
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61071025 and 61502538)
文摘Stochastic resonance(SR) has been proved to be an effective approach to extract weak signals overwhelmed in noise.However, the detection effect of current SR models is still unsatisfactory. Here, a coupled tri-stable stochastic resonance(CTSSR) model is proposed to further increase the output signal-to-noise ratio(SNR) and improve the detection effect of SR. The effects of parameters a, b, c, and r in the proposed resonance system on the SNR are studied, by which we determine a set of parameters that is relatively optimal to implement a comparison with other classical SR models.Numerical experiment results indicate that this proposed model performs better in weak signal detection applications than the classical ones with merits of higher output SNR and better anti-noise capability.
基金supported by the National Natural Science Foundation of China(61202078)
文摘Weak global navigation satellite system(GNSS) signal acquisition has been a limitation for high sensitivity GPS receivers. This paper modifies the traditional acquisition algorithms and proposes a new weak GNSS signal acquisition method using re-scaling and adaptive stochastic resonance(SR). The adoption of classical SR is limited to low-frequency and periodic signals. Given that GNSS signal frequency is high and that the periodic feature of the GNSS signal is affected by the Doppler frequency shift, classical SR methods cannot be directly used to acquire GNSS signals. Therefore, the re-scaling technique is used in our study to expand its usage to high-frequency signals and adaptive control technique is used to gradually determine the Doppler shift effect in GNSS signal buried in strong noises. The effectiveness of our proposed method was verified by the simulations on GPS L1 signals. The simulation results indicate that the new algorithm based on SR can reach-181 d BW sensitivity with a very short data length of 1 ms.
基金Project supported by the National Natural Science Foundation of China(Grant No.61673066)
文摘The conventional Duffing oscillator weak signal detection method, which is based on a strong reference signal, has inherent deficiencies. To address these issues, the characteristics of the Duffing oscillator's phase trajectory in a smallscale periodic state are analyzed by introducing the theory of stopping oscillation system. Based on this approach, a novel Duffing oscillator weak wide-band signal detection method is proposed. In this novel method, the reference signal is discarded, and the to-be-detected signal is directly used as a driving force. By calculating the cosine function of a phase space angle, a single Duffing oscillator can be used for weak wide-band signal detection instead of an array of uncoupled Duffing oscillators. Simulation results indicate that, compared with the conventional Duffing oscillator detection method,this approach performs better in frequency detection intervals, and reduces the signal-to-noise ratio detection threshold,while improving the real-time performance of the system.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 40374045 and 40574051）, and by the Jilin Technology Development Plan （Grant No 20050526）,
文摘In the infrared spectrum absorbed type gas concentration sensor,voltage signal obtained from the two-channel thermopile infrared detector TPS2534 is very weak.In order to solve this problem,the authors have established the structure of the sensor and designed weak signal detecting circuit of the sensor based on infrared spectrum absorption principle,differential de-noising principle and weak signal detecting principle.The authors have made experiments using CH4 gas.The results show that the circuit can remove noise effectively and detect weak electrical signal obtained from the detector.
基金supported by the National Natural Science Foundation for Young Scientists of China(61201190)
文摘Vehicle positioning with the global navigation satellite system(GNSS) in urban environments faces two problems which are attenuation and dynamic.For traditional GNSS receivers hardly able to track dynamic weak signals,the coupling between all visible satellite signals is ignored in the absence of navigation state feedback,and thermal noise error and dynamic stress threshold are contradictory due to non-coherent discriminators.The vector delay/frequency locked loop(VDFLL) with navigation state feedback and the joint vector tracking loop(JVTL) with coherent discriminator which is a synchronization parameter tracking loop based on maximum likelihood estimation(MLE) are proposed to improve the tracking sensitivity of GNSS receiver in dynamic weak signal environments.A joint vector position tracking loop(JVPTL) directly tracking user position and velocity is proposed to further improve tracking sensitivity.The coherent navigation parameter discriminator of JVPTL,being able to ease the contradiction between thermal noise error and dynamic stress threshold,is based on MLE according to the navigation parameter based linear model of received baseband signals.Simulation results show that JVPTL,which combines the advantages of both VDFLL and JVTL,performs better than both VDFLL and JVTL in dynamic weak signal environments.
基金sponsored by the Spark Program of Earthquake Science and Technology,CEA(XH16003)the National Natural Science Foundation(NNSF) of China under Grant No.41474087
文摘Based on the data synthesis simulation and the actual processing of the airgun seismic source signal,three quantitative indicators of signal-to-noise ratio,waveform correlation coefficient and phase offset,are superimposed. We systematically evaluate the functions of the following three stack methods including linearity,phase weighting and S-transform in the extraction of weak signals under strong background noise and quantitatively estimate the reliability of the stack results. Through the comprehensive discussion of the above three methods of stack results,the preliminary comparative analysis believes that the linear stack signal-to-noise ratio is low,but the waveform distortion is minimal; the phase-weighted superimposed signal-to-noise ratio is high and the phase offset is small,but the results of the waveform quality and linear stack are larger than the deviation; the S-transform stack has a relatively higher signal-to-noise ratio and a small loss of waveform amplitude,but there is a certain phase shift phenomenon. It is therefore suggested that linear stack technology should be used when the requirements of both waveform quality and time precision are high. However,the selection of the stack method when the airgun source excitation is limited should be emphasized. If high fidelity is required, the S-transform stack method should be selected; if the required time is high,accuracy can be selected by phase-weighted stack method to achieve reasonable extraction of weak signals.
基金Project supported by the National Natural Science Foundation of China(Grant No.61501525)the National Natural Science Foundation of Hunan Province of China(Grant No.2018JJ3680)。
文摘We propose a joint exponential function and Woods–Saxon stochastic resonance(EWSSR)model.Because change of a single parameter in the classical stochastic resonance model may cause a great change in the shape of the potential function,it is difficult to obtain the optimal output signal-to-noise ratio by adjusting one parameter.In the novel system,the influence of different parameters on the shape of the potential function has its own emphasis,making it easier for us to adjust the shape of the potential function.The system can obtain different widths of the potential well or barrier height by adjusting one of these parameters,so that the system can match different types of input signals adaptively.By adjusting the system parameters,the potential function model can be transformed between the bistable model and the monostable model.The potential function of EWSSR has richer shapes and geometric characteristics.The effects of parameters,such as the height of the barrier and the width of the potential well,on SNR are studied,and a set of relatively optimal parameters are determined.Moreover,the EWSSR model is compared with other classical stochastic resonance models.Numerical experiments show that the proposed EWSSR model has higher SNR and better noise immunity than other classical stochastic resonance models.Simultaneously,the EWSSR model is applied to the detection of actual bearing fault signals,and the detection effect is also superior to other models.
基金Supported by the National Natural Science Foundation of China under Grant No 61371170the Fundamental Research Funds for the Central Universities under Grant Nos NP2015404 and NS2016038+1 种基金the Aeronautical Science Foundation of China under Grant No 20152052028the Funding of Jiangsu Innovation Program for Graduate Education under Grant No KYLX15_0282
文摘Based on the asymptotic spectral distribution of Wigner matrices,a new normality test method is proposed via reforming the white noise sequence.In this work,the asymptotic cumulative distribution function(CDF)of eigenvalues of the Wigner matrix is deduced.A numerical Kullback-Leibler divergence of the empirical spectral CDF based on test samples from the deduced asymptotic CDF is established,which is treated as the test statistic.For validating the superiority of our proposed normality test,we apply the method to weak 8PSK signal detection in the single-input single-output(SISO) system and the single-input multiple-output(SIMO)system.By comparing with other common normality tests and the existing signal detection methods,simulation results show that the proposed method is superior and robust.
基金This work has been partially supported by the Ministry of Science and Technology,Taiwan[Grant numbers MOST 101-2221-E-019-027-MY3 and MOST 109-2221-E-019-010].
文摘In this paper,the data wipe-off(DWO)algorithm is incorporated into the vector tracking loop of the Global Positioning System(GPS)receiver for improving signal tracking performance.The navigation data,which contains information that is necessary to perform navigation computations,are binary phase-shift keying(BPSK)modulated onto the GPS carrier phase with the bit duration of 20 ms(i.e.,50 bits per second).To continuously track the satellite’s signal in weak signal environment,the DWO algorithm on the basis of pre-detection method is adopted to detect data bit sign reversal every 20 ms.Tracking accuracy of a weak GPS signal is decreased by possible data bit sign reversal every 20 ms to the predetection integration time(PIT)or integration interval.To achieve better tracking performance in weak signal environment,the coherent integration interval can be extended.However,increase of the integration interval lead to decrease of the tracking accuracy by possible data bit sign reversal every 20 ms to the integration interval.When the integration interval of the correlator is extended over 20 ms in low C/No levels,the navigation DWO algorithm can be employed to avoid energy loss due to bit transitions.The method presented in this paper has an advantage to continuously estimate the navigation data bit and achieve improved tracking performance.Evaluation of the tracking performance based on the various integration intervals for the vector tracking loop of a GPS receiver will be presented.
文摘New positioning applications’ availability requirements demand receivers with higher sensitivities and ability to process multiple GNSS signals. Possible applications include acquiring one signal per GNSS constellation in the same frequency band and combining them for increased sensitivity or predicting acquisition of other signals. Frequency domain processing can be used for this purpose, since it benefits from parallel processing capabilities of Fast Fourier Transform (FFT), which can be efficiently implemented in software receivers. On the other hand, long coherent integration times are mainly limited due to large FFT size in receivers using frequency domain techniques. A new method is proposed to address the problems in frequency domain receivers without compromising the resources and execution time. A pre-correlation accumulation (PCA) is proposed to partition the received samples into one-code-period blocks, and to sum them together. As a result, the noise is averaged out and the correlation results will gain more power, provided that the relative phase between the data segments is compensated for. In addition to simplicity, the proposed PCA method enables the use of one-size FFT for all integration times. A post-correlation peak combination is also proposed to remove the need for double buffering. The proposed methods are implemented in a configurable Simulink model, developed for acquiring recorded GNSS signals. For weak signal scenarios, a Spirent GPS simulator is used as a source. Acquisition results for GPS L1 C/A and GLONASS L1OF are shown and the performance of the proposed technique is discussed. The proposed techniques target GNSS receivers using frequency domain processing aiming at accommodating all the GNSS signals, while minimizing resource usage. They also apply to weak signal acquisition in frequency domain to answer the availability demand of today’s GNSS positioning applications.
基金The Basic Science Research Project of Commonweal of Nation Level (DQJB06A02 ),ChinaThe Brightlight (Ⅰ) Project from Institute of Geophysics,CEA
文摘Waveforms generated by the 50t explosion of project Brightlight(Ⅰ) were recorded by HILR array.Using array techniques,the author performed identification,f-k analysis,velocity spectrum analysis,etc.of the weak signals.The analysis results show that the signal-to-noise ratio after beamforming was obviously enhanced,and the signal could be clearly shown.The energy from this explosion was mainly concentrated in the 1 ～ 8Hz range from f-k analysis.The velocity spectrum gave clear positions of event phases,which could not be seen in the original weak signals.The maximum energy distribution obtained by the Beaman method is close to the theoretical value in the azimuth-slowness domain.
