This paper addresses the micro wind-hydrogen coupled system,aiming to improve the power tracking capability of micro wind farms,the regulation capability of hydrogen storage systems,and to mitigate the volatility of w...This paper addresses the micro wind-hydrogen coupled system,aiming to improve the power tracking capability of micro wind farms,the regulation capability of hydrogen storage systems,and to mitigate the volatility of wind power generation.A predictive control strategy for the micro wind-hydrogen coupled system is proposed based on the ultra-short-term wind power prediction,the hydrogen storage state division interval,and the daily scheduled output of wind power generation.The control strategy maximizes the power tracking capability,the regulation capability of the hydrogen storage system,and the fluctuation of the joint output of the wind-hydrogen coupled system as the objective functions,and adaptively optimizes the control coefficients of the hydrogen storage interval and the output parameters of the system by the combined sigmoid function and particle swarm algorithm(sigmoid-PSO).Compared with the real-time control strategy,the proposed predictive control strategy can significantly improve the output tracking capability of the wind-hydrogen coupling system,minimize the gap between the actual output and the predicted output,significantly enhance the regulation capability of the hydrogen storage system,and mitigate the power output fluctuation of the wind-hydrogen integrated system,which has a broad practical application prospect.展开更多
Microstructure and texture evolution during high-strain-rate superplastic deformation of the rolled Mg-Gd-Y-Zr sheet were investigated.The tensile tests at the strain rate of 0.01 s-1 achieved the elongations of 180%-...Microstructure and texture evolution during high-strain-rate superplastic deformation of the rolled Mg-Gd-Y-Zr sheet were investigated.The tensile tests at the strain rate of 0.01 s-1 achieved the elongations of 180%-266% in the deformation temperature range of 400-500 ℃.Post-deforming microstructures were characterized by optical microscopy,scanning electron microscopy and transmission electron microscopy,while crystallographic orientation information was obtained from macro-texture analysis.The results show that the high strain-rate superplasticity was attributed to class-I dislocation creep accommodated by dynamic recrystallization （DRX）.During preheating at 435 ℃ for 600 s,twinning-induced recrystallization occurred.The initial strain of 80% made original grains fragmented and produced homogenous DRX grains.The interaction between dynamic recrystallization and dynamic precipitation yielded out such a phenomenon that finer DRX grains were often accompanied by denser particles.The macro-texture evolution exhibited some characteristics of the crystal rotation arising from basal slip and prismatic slip despite the occurrence of DRX.展开更多
Based on the construction interfaces in rolled control concrete dam(RCCD), the methods were proposed to calculate the influence thickness of construction interfaces and the corresponding physical mechanics parameters....Based on the construction interfaces in rolled control concrete dam(RCCD), the methods were proposed to calculate the influence thickness of construction interfaces and the corresponding physical mechanics parameters. The principle on establishing the coupling model of seepage_field and stress_field for RCCD was presented. A 3_D Finite Element Method(FEM) program was developed. Study shows that such parameters as the thickness of construction interfaces,the elastic ratio and the (Poisson's) ratio obtained by tests and theoretical analysis are more reasonable, the coupling model of seepage_field and stress_field for RCCD may indicate the coupling effect between the two fields scientifically, and the developed 3_D FEM program can reflect the effect of the construction interfaces more adequately. According to the study, many scientific opinions are given both to analyze the influence of the construction interfaces to the (dam's) characteristic, and to reveal the interaction between the stress_field and the seepage_field.展开更多
The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K（0.67Tm-0.76Tm） and high strain rates ranging from 10^-3 to 1 s^...The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K（0.67Tm-0.76Tm） and high strain rates ranging from 10^-3 to 1 s^-1 were investigated.The rolled AZ91 magnesium alloy possesses excellent superplasticity with the maximum elongation of 455% at 623 K and a strain rate of 10-3 s-1,and its strain rate sensitivity m is high up to 0.64.The dominant deformation mechanism responsible for the high strain rate superplasticity is still grain boundary sliding（GBS）,and the dislocation creep mechanism is considered as the main accommodation mechanism.展开更多
Room-temperature(RT) formability is a key factor to broaden the applications of rolled Mg alloy sheets in the industry. However, rolled Mg alloy sheets generally form strong basal texture, where the(0001) poles align ...Room-temperature(RT) formability is a key factor to broaden the applications of rolled Mg alloy sheets in the industry. However, rolled Mg alloy sheets generally form strong basal texture, where the(0001) poles align parallel to the normal direction(ND). This hinders the activation of(0001) [1120] basal slip, limiting the RT formability. Therefore, texture weakening, i.e., the inclination of the(0001) poles from the ND, plays an important role to improve the RT formability. Recrystallization is crucial to control the textural development in Mg,and currently, the texture weakening is commonly achieved using static recrystallization(SRX). However, the type of slipping and twinning,which are activated during rolling, affect the textural features after SRX. It is also demonstrated that shear bands and preferential grain growth are important factors to tailor the texture during SRX. Indeed, dynamic recrystallization(DRX) easily occurs during rolling in Mg, which also affects the final rolling texture, while the effect of DRX on the textural formation is not extensively studied for the development of RT-formable Mg alloy sheets. Therefore, the effect of these factors on the textural development in rolled Mg is reviewed in this manuscript.Additionally, the ideal microstructure and texture for RT-formable Mg alloy sheets are still controversial. The RT-formability includes stretch forming(biaxial tension), bending(plane strain tension), and deep-drawing. In particular, the stretch forming is commonly used to evaluate the RT-formability of rolled Mg. Although the stretch formability has been improved by recent studies, the further improvement is necessary owing to the relatively low formability of rolled Mg compared with that of rolled Fe and Al. Based on the relationship between the microstructure/texture and stretch formability provided in the literature, the design guidance for high stretch formability is proposed in this review.展开更多
Cryogenic rolling experiments have been conducted on the AZ31 magnesium(Mg)alloy sheet with bimodal non-basal texture,which is fabricated via the newly developed equal channel angular rolling and continuous bending pr...Cryogenic rolling experiments have been conducted on the AZ31 magnesium(Mg)alloy sheet with bimodal non-basal texture,which is fabricated via the newly developed equal channel angular rolling and continuous bending process with subsequent annealing(ECAR-CB-A)process.Results demonstrate that this sheet shows no edge cracks until the accumulated thickness reduction reaches about 18.5%,which is about 105.6%larger than that of the sheet with traditional basal texture.Characterization experiments including optical microstructure(OM),X-ray diffractometer(XRD),and electron backscatter diffraction(EBSD)measurements are then performed to explore the microstructure characteristics,texture evolution and deformation mechanisms during cryogenic rolling.Experimental observations confirm the occurrence of abundant{10–12}extension twins(ETs),twin-twin interactions among{10–12}ET variants and{10–12}-{10–12}double twins(DTs).The twinning behaviors as for{10–12}ETs are responsible for the concentration of c-axes of grains towards normal direction(ND)and the formation of transverse direction(TD)-component texture at the beginning of cryogenic rolling.The twinning behaviors with respect to{10–12}-{10–12}DTs are responsible for the disappearance of TD-component texture at the later stage of cryogenic rolling.The involved deformation mechanisms can be summarized as follows:Firstly{10–12}ETs dominate the plastic deformation.Subsequently,dislocation slip,especially basal<a>slip,starts to sustain more plastic strain,while{10–12}ETs occur more frequently and enlarge continuously,resulting in the formation of twin-twin interaction among{10–12}ET variants.With the increasing rolling passes,{10–12}-{10–12}DTs incorporate in the plastic deformation and dislocation slip serves as the major one to sustain plastic strain.The activities of basal<a>slip,{10–12}ETs and{10–12}-{10–12}DTs benefit in accommodating the plastic strain in sheet thickness,which contributes to the improved rolling formability in AZ31 Mg alloy sheet with bimodal non-basal texture during cryogenic rolling.展开更多
A superplastic tension test was carried out in order to examine the anisotropy of superplasticity in hot rolled sheet of Ti-10V-2Fe-3Al. Flow stress in the longitudinal (L) direction is higher than that in the transve...A superplastic tension test was carried out in order to examine the anisotropy of superplasticity in hot rolled sheet of Ti-10V-2Fe-3Al. Flow stress in the longitudinal (L) direction is higher than that in the transverse (T) direction of the sheet. The peak value of elongation in L direction specimens is also higher within a strain rate range of 0.0005-0.0083/s. Based on microstructure changes before and after superplastically deformation, an analysis is made for multi-necking on the T specimen after tension. The flowlines in superplastically deformed specimen are described.展开更多
In the present study,through vertical roll pre-rolling of AZ31 magnesium alloy hot-rolled plate at room temperature,the effect of different vertical roll pre-rolling reduction on edge crack of the plate during flat ro...In the present study,through vertical roll pre-rolling of AZ31 magnesium alloy hot-rolled plate at room temperature,the effect of different vertical roll pre-rolling reduction on edge crack of the plate during flat rolling was systematically studied.The evolution of microstructure and texture in the edge and middle of the plate after vertical roll pre-rolling,heating and rolling was analyzed by using EBSD technology.The results show that during the vertical roll pre-rolling,{10–12}primary twins and{10–12}-{10–12}secondary twins dominated the edge deformation,while{10–12}primary twins dominated the middle deformation.With the increase of vertical roll pre-rolling reduction,the twin volume fraction of the edge and the middle increased,and the difference between them decreased gradually.After heating,the twin orientation caused by vertical roll pre-rolling was still maintained,and there was a significant difference in grain size between the edge and the middle.When the reduction rate of flat rolling was 30%,cracks have already appeared in the initial plate,while the vertical roll pre-rolled samples showed extremely high rolling performance.When the reduction rate of flat rolling was 50%,the 8PR sample still had no crack initiation.In addition,after flat rolling of 50%,the initial plate showed a strong basal texture,while the maximum pole density of the 8PR plate was small,and the texture distribution was very scattered,showing the characteristics of weak orientation.展开更多
Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achie...Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achieved by adjusting the diameters of the upper roll and the bottom roll and was used to prepare hot-rolled thick plate of 5182 aluminium alloy. The shear deformation and plate shape control were experimentally studied. The experimental results show that asymmetrical rolling has a significant effect on metal deformation stream and can somehow refine microstructure and improve the uniformity of microstructure and properties. The asymmetrical rolling process can also reduce the rolling force. However, bending of rolling plate often happens during asymmetrical rolling process. The factors affecting the bending were discussed.展开更多
The mechanical properties and texture of AM60（Mg-6.0Al-0.3Mn,mass fraction %） and ZXM200（Mg-1.6Zn-0.5Ca-0.2Mn） Mg alloys subjected to multi-pass hot rolling were investigated.The finer recrystallized grains usuall...The mechanical properties and texture of AM60（Mg-6.0Al-0.3Mn,mass fraction %） and ZXM200（Mg-1.6Zn-0.5Ca-0.2Mn） Mg alloys subjected to multi-pass hot rolling were investigated.The finer recrystallized grains usually exhibit particular preferred orientations and then alter the total texture feature of rolled sheets.Ca solid solution into Mg matrix serves to the formation of texture component with c-axis rotated away from normal direction towards transverse direction and then weakens the overall texture intensity,resulting in a similar anisotropic characteristic to RE-containing Mg alloys.展开更多
Magnesium and magnesium alloy foils have great potential for application in battery anodes,electromagnetic shielding,optics and acoustics,and biology because of their excellent specific damping,internal dissipation co...Magnesium and magnesium alloy foils have great potential for application in battery anodes,electromagnetic shielding,optics and acoustics,and biology because of their excellent specific damping,internal dissipation coefficients,magnetic and electrical conductivities,as well as high theoretical specific capacity.However,magnesium alloys exhibit poor deformation ability due to their hexagonal close-packed crystal structure.Preparing magnesium and magnesium alloy foils with thicknesses of less than 0.1 mm is difficult because of surface oxidation and grain growth at high temperatures or severe anisotropy after cold rolling that leads to cracks.Numerous methods have been applied to prepare magnesium alloy foils.They include warm rolling,cold rolling,accumulative roll bonding,electric plastic rolling,and on-line heating rolling.Defects of magnesium and magnesium alloy foils during preparation,such as edge cracks and breakage,are important factors for consideration.Herein,the current status of the research on magnesium and magnesium alloy foils is summarized from the aspects of foil preparation,defect control,performance characterization,and application prospects.The advantages and disadvantages of different preparation methods and defect(edge cracks and breakage)mechanisms in the preparation of foils are identified.展开更多
Innovative pulsed current-assisted multi-pass rolling tests were conducted on a 12-roll mill during the rolling deformation processing of SUS304 ultra-thin strips.The results show that in the first rolling pass,the ro...Innovative pulsed current-assisted multi-pass rolling tests were conducted on a 12-roll mill during the rolling deformation processing of SUS304 ultra-thin strips.The results show that in the first rolling pass,the rolling reduction rate of a conventionally rolled sample(at room temperature)is 33.8%,which can be increased to 41.5%by pulsed current-assisted rolling,enabling the formation of an ultra-thin strip with a size of 67.3μm in only one rolling pass.After three passes of pulsed current-assisted rolling,the thickness of the ultra-thin strip can be further reduced to 51.7μm.To clearly compare the effects of a pulsed current on the microstructure and mechanical response of the ultra-thin strip,ultra-thin strips with nearly the same thickness reduction were analyzed.It was found that pulsed current can reduce the degree of work-hardening of the rolled samples by promoting dislocation detachment,reducing the density of stacking faults,inhibiting martensitic phase transformation,and shortening the total length of grain boundaries.As a result,the ductility of ultra-thin strips can be effectively restored to approximately 16.3%while maintaining a high tensile strength of 1118 MPa.Therefore,pulsed current-assisted rolling deformation shows great potential for the formation of ultra-thin strips with a combination of high strength and ductility.展开更多
Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titaniu...Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titanium alloy plates were prepared by cold press-ing sintering combined with high-temperature hot rolling.The microstructure and mechanical properties under different process paramet-ers were investigated.Optical microscope,electron backscatter diffraction,and others were applied to characterize the microstructure evolution and mechanical properties strengthening mechanism.The results showed that the chemical compositions were uniformly dif-fused without segregation during sintering,and the closing of the matrix craters was accelerated by increasing the sintering temperature.The block was hot rolled at 1200℃ with an 80%reduction under only two passes without annealing.The strength and elongation of the plate at 20–25℃ after solution and aging were 1247 MPa and 14.0%,respectively,which were increased by 24.5%and 40.0%,respect-ively,compared with the as-sintered alloy at 1300℃.The microstructure was significantly refined by continuous dynamic recrystalliza-tion,which was completed by the rotation and dislocation absorption of the substructure surrounded by low-angle grain boundaries.After hot rolling combined with heat treatment,the strength and plasticity of PM-TA15 were significantly improved,which resulted from the dense,uniform,and fine recrystallization structure and the synergistic effect of multiple slip systems.展开更多
Mechanical and shape memory properties of a Ti50Ni47Fe3 alloy annealed at 450-750 °C for 1 h after a cold-rolled reduction of 25% were investigated by phase transformation analysis and microstructure characteriza...Mechanical and shape memory properties of a Ti50Ni47Fe3 alloy annealed at 450-750 °C for 1 h after a cold-rolled reduction of 25% were investigated by phase transformation analysis and microstructure characterization using tensile tests, Vickers hardness tests, electrical resistivity-temperature tests, SEM and TEM. From the results of the tensile, it can be inferred that the fracture stress and yield stress decreased and the fracture elongation increased as the annealing temperature increased for the rolled Ti50Ni47Fe3 alloy. They reached stead values when the temperature was above 650 °C. The change in Vickers hardness corresponded to the change in the fracture stress and yield stress. The electrical resistivity-temperature curves suggest that a two- stage martensitic transformation（B2-R-B19′） occurred during cooling and heating. The transformation temperatures decreased to lower temperatures when the annealing temperature was increased and maintained the same after the annealing temperature reached 650 °C. TEM revealed the distinct processes occurring at elevated temperatures： recovery, polygonization, and recrystallization.展开更多
Ground roll waves interfere with seismic data. The suppression of ground roll waves based on the division of wavelet frequencies considers the low-frequency characteristics of ground roll waves. However, this method w...Ground roll waves interfere with seismic data. The suppression of ground roll waves based on the division of wavelet frequencies considers the low-frequency characteristics of ground roll waves. However, this method will not be effective when the ground roll wave and the effective signal have the same frequency bands because of overlapping. The radial trace transform （RTT） considers the apparent velocity difference between the effective signal and the ground roll wave to suppress the latter, but affects the low-frequency components of the former. This study proposes a ground roll wave suppression method by combining the wavelet frequency division and the RTT based on the difference between the ground roll wave velocity and the effective signal and their energy difference in the wavelet domain, thus making full use of the advantages of both methods. First, we decompose the seismic data into different frequency bands through wavelet transform. Second, the RTT and low-cut filtering are applied to the low-frequency band, where the ground roll waves are appearing. Third, we reconstruct the seismic record without ground roll waves by using the inverse RTT and the remaining frequency bands. The proposed method not only improves the ground roll wave suppression, but also protects the signal integrity. The numerical simulation and real seismic data processing results suggest that the proposed method has a strong ability to denoise while preserving the amplitude.展开更多
3%Y_(2)O_(3)p/ZGK200 composites were subjected to unidirectional rolling(UR)and cross rolling(CR)at 400℃and 350℃followed by annealing at 300℃for 1 h.The microstructure,texture and mechanical properties of rolled an...3%Y_(2)O_(3)p/ZGK200 composites were subjected to unidirectional rolling(UR)and cross rolling(CR)at 400℃and 350℃followed by annealing at 300℃for 1 h.The microstructure,texture and mechanical properties of rolled and annealed composites were systematically studied.The rolled composites exhibited a heterogeneous microstructure,consisting of deformed grains elongated along rolling direction(RD)and Y_(2)O_(3)particles bands distributed along RD.After annealing,static recrystallization(SRX)occurred and most deformed grains transformed into equiaxed grains.A non-basal texture with two strong T-texture components was obtained after UR while a non-basal elliptical/circle texture with circle multi-peaks was obtained after CR,indicating that rolling path had great influences on texture of the composites.After annealing process,R-texture component disappeared or weakened,as results,a non-basal texture with double peaks tilting from normal direction(ND)to transverse direction(TD)and a more random non-basal texture with circle multi-peaks were obtained for UR and CR composites,respectively.The yield strength of rolled composites after UR showed obvious anisotropy along RD and TD while a low anisotropic yield strength was obtained after CR.Some Y_(2)O_(3)particles broke during rolling.The fracture of the composites was attributed to the existence of Y_(2)O_(3)clusters and interfacial debonding between particles and matrix during tension,as a result,the ductility was not as superior as matrix alloy.展开更多
A dynamic plant architecture is the basis of plant adaptation to changing environments.Although many genes regulating leaf rolling have been identified,genes directly associated with water homeostasis are largely unkn...A dynamic plant architecture is the basis of plant adaptation to changing environments.Although many genes regulating leaf rolling have been identified,genes directly associated with water homeostasis are largely unknown.Here,we isolated a rice mutant,dynamic leaf rolling 1(dlr1),characterized by‘leaf unfolding in the morning-leaf rolling at noon-leaf unfolding in the evening’during a sunny day.Water content was decreased in rolled leaves and water sprayed on leaves caused reopening,indicating that in vivo water deficiency induced the leaf rolling.Map-based cloning and expression tests demonstrated that an A1400G single base mutation in Oryza sativa Polygalacturonase 1(OsPG1)/PHOTO-SENSITIVE LEAF ROLLING 1(PSL1)was responsible for the dynamic leaf rolling phenotype in the dlr1 mutant.OsPG1 encodes a polygalacturonase,one of the main enzymes that degrade demethylesterified homogalacturonans in plant cell walls.OsPG1 was constitutively expressed in various tissues and was enriched in stomata.Mutants of the OsPG1 gene exhibited defects in stomatal closure and decreased stomatal density,leading to reduced transpiration and excessive water loss under specific conditions,but had normal root development.Further analysis revealed that mutation of OsPG1 led to reduced pectinase activity in the leaves and increased demethylesterified homogalacturonans in guard cells.Our findings reveal a mechanism by which OsPG1 modulates water homeostasis to control dynamic leaf rolling,providing insights for plants to adapt to environmental variation.展开更多
Automobiles are the inevitable mode of transportation.However,increasing fuel prices and carbon dioxide emissions are posing a serious threat to automobile users and the environment.Thus,the development of new lightwe...Automobiles are the inevitable mode of transportation.However,increasing fuel prices and carbon dioxide emissions are posing a serious threat to automobile users and the environment.Thus,the development of new lightweight materials has been a key area of research.Magnesium-based commercial alloys(AZ and ZK series alloys)are the lightest among all structural metals.However,there is still a question about the replacement of Aluminum-based alloys due to HCP crystal structure.In this connection,Mg-Al-Ca-Mn(AXM)Mg alloy can be a choice as an alternative to the existing Mg-based commercial alloys for structural applications.It contains(Al,Mg)_(2)Ca,Al_(2)Ca,Mg_(2)Ca,and Al_(8)Mn_(5)as the secondary phases,contributing to the microstructural refinement and property enhancement.However,the formation of those precipitates depends on the amount of Al,Ca,and Mn,especially,the Ca/Al ratio.In addition,the secondary processes influence the grain refinement and property enhancement of texture modifications.Hence,this review article focuses on elaborating on the significance of the Ca/Al ratio for the precipitate formation,secondary process,and texture modifications.The co-segregation behavior of other micro-alloying elements like Cerium,Lanthanum,and Zinc in AXM Mg alloy systems has also been discussed for property enhancement.展开更多
The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formabilit...The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formability of Al-Cu-Li alloy is vital.A thorough comparison of the effects of cryo-deformation and ambient temperature large pre-deformation(LPD)on the creep ageing response in the 2195 alloy sheet at 160℃with different stresses has been made.The evolution of dislocations and precipitates during creep ageing of LPD alloys are revealed by X-ray diffraction and transmission electron microscopy.High-quality 2195 alloy sheet largely pre-deformed by 80%without edge-cracking is obtained by cryo-rolling at liquid nitrogen temperature,while severe edge-cracking occurs during room temperature rolling.The creep formability and strength of the 2195 alloy are both enhanced by introducing pre-existing dislocations with a density over 1.4×10^(15)m^(−2).At 160℃and 150 MPa,creep strain and creep-aged strength generally increases by 4−6 times and 30−50 MPa in the LPD sample,respectively,compared to conventional T3 alloy counterpart.The elongation of creep-aged LPD sample is low but remains relevant for application.The high-density dislocations,though existing in the form of dislocation tangles,promote the formation of refined T1 precipitates with a uniform dispersion.展开更多
基金the Key Research&Development Program of Xinjiang(Grant Number 2022B01003).
文摘This paper addresses the micro wind-hydrogen coupled system,aiming to improve the power tracking capability of micro wind farms,the regulation capability of hydrogen storage systems,and to mitigate the volatility of wind power generation.A predictive control strategy for the micro wind-hydrogen coupled system is proposed based on the ultra-short-term wind power prediction,the hydrogen storage state division interval,and the daily scheduled output of wind power generation.The control strategy maximizes the power tracking capability,the regulation capability of the hydrogen storage system,and the fluctuation of the joint output of the wind-hydrogen coupled system as the objective functions,and adaptively optimizes the control coefficients of the hydrogen storage interval and the output parameters of the system by the combined sigmoid function and particle swarm algorithm(sigmoid-PSO).Compared with the real-time control strategy,the proposed predictive control strategy can significantly improve the output tracking capability of the wind-hydrogen coupling system,minimize the gap between the actual output and the predicted output,significantly enhance the regulation capability of the hydrogen storage system,and mitigate the power output fluctuation of the wind-hydrogen integrated system,which has a broad practical application prospect.
基金Project supported by Natural Science Foundation of Hunan Province,China
文摘Microstructure and texture evolution during high-strain-rate superplastic deformation of the rolled Mg-Gd-Y-Zr sheet were investigated.The tensile tests at the strain rate of 0.01 s-1 achieved the elongations of 180%-266% in the deformation temperature range of 400-500 ℃.Post-deforming microstructures were characterized by optical microscopy,scanning electron microscopy and transmission electron microscopy,while crystallographic orientation information was obtained from macro-texture analysis.The results show that the high strain-rate superplasticity was attributed to class-I dislocation creep accommodated by dynamic recrystallization （DRX）.During preheating at 435 ℃ for 600 s,twinning-induced recrystallization occurred.The initial strain of 80% made original grains fragmented and produced homogenous DRX grains.The interaction between dynamic recrystallization and dynamic precipitation yielded out such a phenomenon that finer DRX grains were often accompanied by denser particles.The macro-texture evolution exhibited some characteristics of the crystal rotation arising from basal slip and prismatic slip despite the occurrence of DRX.
文摘Based on the construction interfaces in rolled control concrete dam(RCCD), the methods were proposed to calculate the influence thickness of construction interfaces and the corresponding physical mechanics parameters. The principle on establishing the coupling model of seepage_field and stress_field for RCCD was presented. A 3_D Finite Element Method(FEM) program was developed. Study shows that such parameters as the thickness of construction interfaces,the elastic ratio and the (Poisson's) ratio obtained by tests and theoretical analysis are more reasonable, the coupling model of seepage_field and stress_field for RCCD may indicate the coupling effect between the two fields scientifically, and the developed 3_D FEM program can reflect the effect of the construction interfaces more adequately. According to the study, many scientific opinions are given both to analyze the influence of the construction interfaces to the (dam's) characteristic, and to reveal the interaction between the stress_field and the seepage_field.
基金supported by the National Natural Science Foundation of China(No.50674067).
文摘The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K（0.67Tm-0.76Tm） and high strain rates ranging from 10^-3 to 1 s^-1 were investigated.The rolled AZ91 magnesium alloy possesses excellent superplasticity with the maximum elongation of 455% at 623 K and a strain rate of 10-3 s-1,and its strain rate sensitivity m is high up to 0.64.The dominant deformation mechanism responsible for the high strain rate superplasticity is still grain boundary sliding（GBS）,and the dislocation creep mechanism is considered as the main accommodation mechanism.
基金supported by JSPS KAKENHI Grant Numbers JP22H00259 and JP22K18900。
文摘Room-temperature(RT) formability is a key factor to broaden the applications of rolled Mg alloy sheets in the industry. However, rolled Mg alloy sheets generally form strong basal texture, where the(0001) poles align parallel to the normal direction(ND). This hinders the activation of(0001) [1120] basal slip, limiting the RT formability. Therefore, texture weakening, i.e., the inclination of the(0001) poles from the ND, plays an important role to improve the RT formability. Recrystallization is crucial to control the textural development in Mg,and currently, the texture weakening is commonly achieved using static recrystallization(SRX). However, the type of slipping and twinning,which are activated during rolling, affect the textural features after SRX. It is also demonstrated that shear bands and preferential grain growth are important factors to tailor the texture during SRX. Indeed, dynamic recrystallization(DRX) easily occurs during rolling in Mg, which also affects the final rolling texture, while the effect of DRX on the textural formation is not extensively studied for the development of RT-formable Mg alloy sheets. Therefore, the effect of these factors on the textural development in rolled Mg is reviewed in this manuscript.Additionally, the ideal microstructure and texture for RT-formable Mg alloy sheets are still controversial. The RT-formability includes stretch forming(biaxial tension), bending(plane strain tension), and deep-drawing. In particular, the stretch forming is commonly used to evaluate the RT-formability of rolled Mg. Although the stretch formability has been improved by recent studies, the further improvement is necessary owing to the relatively low formability of rolled Mg compared with that of rolled Fe and Al. Based on the relationship between the microstructure/texture and stretch formability provided in the literature, the design guidance for high stretch formability is proposed in this review.
基金supported by the National Natural Science Foundation of China(Grant Nos.51805064,51822509)the Qingnian project of science and technology research program of Chongqing Education Commission of China(Grant No.KJQN202101141).
文摘Cryogenic rolling experiments have been conducted on the AZ31 magnesium(Mg)alloy sheet with bimodal non-basal texture,which is fabricated via the newly developed equal channel angular rolling and continuous bending process with subsequent annealing(ECAR-CB-A)process.Results demonstrate that this sheet shows no edge cracks until the accumulated thickness reduction reaches about 18.5%,which is about 105.6%larger than that of the sheet with traditional basal texture.Characterization experiments including optical microstructure(OM),X-ray diffractometer(XRD),and electron backscatter diffraction(EBSD)measurements are then performed to explore the microstructure characteristics,texture evolution and deformation mechanisms during cryogenic rolling.Experimental observations confirm the occurrence of abundant{10–12}extension twins(ETs),twin-twin interactions among{10–12}ET variants and{10–12}-{10–12}double twins(DTs).The twinning behaviors as for{10–12}ETs are responsible for the concentration of c-axes of grains towards normal direction(ND)and the formation of transverse direction(TD)-component texture at the beginning of cryogenic rolling.The twinning behaviors with respect to{10–12}-{10–12}DTs are responsible for the disappearance of TD-component texture at the later stage of cryogenic rolling.The involved deformation mechanisms can be summarized as follows:Firstly{10–12}ETs dominate the plastic deformation.Subsequently,dislocation slip,especially basal<a>slip,starts to sustain more plastic strain,while{10–12}ETs occur more frequently and enlarge continuously,resulting in the formation of twin-twin interaction among{10–12}ET variants.With the increasing rolling passes,{10–12}-{10–12}DTs incorporate in the plastic deformation and dislocation slip serves as the major one to sustain plastic strain.The activities of basal<a>slip,{10–12}ETs and{10–12}-{10–12}DTs benefit in accommodating the plastic strain in sheet thickness,which contributes to the improved rolling formability in AZ31 Mg alloy sheet with bimodal non-basal texture during cryogenic rolling.
文摘A superplastic tension test was carried out in order to examine the anisotropy of superplasticity in hot rolled sheet of Ti-10V-2Fe-3Al. Flow stress in the longitudinal (L) direction is higher than that in the transverse (T) direction of the sheet. The peak value of elongation in L direction specimens is also higher within a strain rate range of 0.0005-0.0083/s. Based on microstructure changes before and after superplastically deformation, an analysis is made for multi-necking on the T specimen after tension. The flowlines in superplastically deformed specimen are described.
基金supported by the National Natural Science Foundation of China(52075357)the national key R&D plan project(2018YFA0707301)+2 种基金the key Research Science and Technology Innovation of Shanxi Province(201803D121026)Shanxi Province Science and Technology Major Project(20181102016)Open Research Fund of State Key Laboratory of High Performance Complex Manufacturing,Central South University(Kfkt2019–03)。
文摘In the present study,through vertical roll pre-rolling of AZ31 magnesium alloy hot-rolled plate at room temperature,the effect of different vertical roll pre-rolling reduction on edge crack of the plate during flat rolling was systematically studied.The evolution of microstructure and texture in the edge and middle of the plate after vertical roll pre-rolling,heating and rolling was analyzed by using EBSD technology.The results show that during the vertical roll pre-rolling,{10–12}primary twins and{10–12}-{10–12}secondary twins dominated the edge deformation,while{10–12}primary twins dominated the middle deformation.With the increase of vertical roll pre-rolling reduction,the twin volume fraction of the edge and the middle increased,and the difference between them decreased gradually.After heating,the twin orientation caused by vertical roll pre-rolling was still maintained,and there was a significant difference in grain size between the edge and the middle.When the reduction rate of flat rolling was 30%,cracks have already appeared in the initial plate,while the vertical roll pre-rolled samples showed extremely high rolling performance.When the reduction rate of flat rolling was 50%,the 8PR sample still had no crack initiation.In addition,after flat rolling of 50%,the initial plate showed a strong basal texture,while the maximum pole density of the 8PR plate was small,and the texture distribution was very scattered,showing the characteristics of weak orientation.
基金Projects(51104043,51374067)supported by the National Natural Science Foundation of ChinaProject(2012CB619506)supported by the National Basic Research Program of ChinaProject(N120409002)supported by the Fundamental Research Funds for the Central Universities,China
文摘Asymmetric rolling （ASR）, as one of severe plastic deformation （SPD） methods to make ultra-fine materials with enhanced performance is mainly used to prepare foil and thin strip. The asymmetrical rolling was achieved by adjusting the diameters of the upper roll and the bottom roll and was used to prepare hot-rolled thick plate of 5182 aluminium alloy. The shear deformation and plate shape control were experimentally studied. The experimental results show that asymmetrical rolling has a significant effect on metal deformation stream and can somehow refine microstructure and improve the uniformity of microstructure and properties. The asymmetrical rolling process can also reduce the rolling force. However, bending of rolling plate often happens during asymmetrical rolling process. The factors affecting the bending were discussed.
基金Project(51204003)supported by the National Natural Science Foundation of ChinaProject(KJ2011A051)supported by the Scientific Research Foundation of Education Department of Anhui Province,China
文摘The mechanical properties and texture of AM60（Mg-6.0Al-0.3Mn,mass fraction %） and ZXM200（Mg-1.6Zn-0.5Ca-0.2Mn） Mg alloys subjected to multi-pass hot rolling were investigated.The finer recrystallized grains usually exhibit particular preferred orientations and then alter the total texture feature of rolled sheets.Ca solid solution into Mg matrix serves to the formation of texture component with c-axis rotated away from normal direction towards transverse direction and then weakens the overall texture intensity,resulting in a similar anisotropic characteristic to RE-containing Mg alloys.
基金financially supported by the National Key Research and Development Program of China(Nos.2022 YFB3709300 and 2021YFB3701000)the National Natural Science Foundation of China(Nos.52271090 and 52071036)+1 种基金the Guangdong Major Project of Basic and Applied Basic Research(No.2020B0301030006)the Independent Research Project of State Key Laboratory of Mechanical Transmissions(Nos.SKLMT-ZZKT-2022Z01 and S KLMT-ZZKT-2022M12)。
文摘Magnesium and magnesium alloy foils have great potential for application in battery anodes,electromagnetic shielding,optics and acoustics,and biology because of their excellent specific damping,internal dissipation coefficients,magnetic and electrical conductivities,as well as high theoretical specific capacity.However,magnesium alloys exhibit poor deformation ability due to their hexagonal close-packed crystal structure.Preparing magnesium and magnesium alloy foils with thicknesses of less than 0.1 mm is difficult because of surface oxidation and grain growth at high temperatures or severe anisotropy after cold rolling that leads to cracks.Numerous methods have been applied to prepare magnesium alloy foils.They include warm rolling,cold rolling,accumulative roll bonding,electric plastic rolling,and on-line heating rolling.Defects of magnesium and magnesium alloy foils during preparation,such as edge cracks and breakage,are important factors for consideration.Herein,the current status of the research on magnesium and magnesium alloy foils is summarized from the aspects of foil preparation,defect control,performance characterization,and application prospects.The advantages and disadvantages of different preparation methods and defect(edge cracks and breakage)mechanisms in the preparation of foils are identified.
基金This work was supported by the fund of the National Natural Science Foundation of China(51974196)Major Program of National Natural Science Foundation of China(U22A20188)+1 种基金Science and Technology Innovation Teams of Shanxi Province(202304051001025)Central Government Guides the Special Fund Projects of Local Scientific and Technological Development(YDZX20191400002149).
文摘Innovative pulsed current-assisted multi-pass rolling tests were conducted on a 12-roll mill during the rolling deformation processing of SUS304 ultra-thin strips.The results show that in the first rolling pass,the rolling reduction rate of a conventionally rolled sample(at room temperature)is 33.8%,which can be increased to 41.5%by pulsed current-assisted rolling,enabling the formation of an ultra-thin strip with a size of 67.3μm in only one rolling pass.After three passes of pulsed current-assisted rolling,the thickness of the ultra-thin strip can be further reduced to 51.7μm.To clearly compare the effects of a pulsed current on the microstructure and mechanical response of the ultra-thin strip,ultra-thin strips with nearly the same thickness reduction were analyzed.It was found that pulsed current can reduce the degree of work-hardening of the rolled samples by promoting dislocation detachment,reducing the density of stacking faults,inhibiting martensitic phase transformation,and shortening the total length of grain boundaries.As a result,the ductility of ultra-thin strips can be effectively restored to approximately 16.3%while maintaining a high tensile strength of 1118 MPa.Therefore,pulsed current-assisted rolling deformation shows great potential for the formation of ultra-thin strips with a combination of high strength and ductility.
基金supported by the National Natural Science Foundation of China(No.52274359)Guangdong Basic and Applied Basic Research Foundation,China(No.2022A1515110406)+3 种基金Beijing Natural Science Foundation,China(No.2212035)the Fundamental Research Funds for the Central Universities,China(Nos.FRF-TP-19005C1Z and 00007718)the Aeroengine Group University Research Cooperation Project,China(No.HFZL2021CXY021)the State Key Lab of Advanced Metals and Materials,University of Science and Technology Beijing,China(Nos.2021Z-03 and 2022Z-14).
文摘Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titanium alloy plates were prepared by cold press-ing sintering combined with high-temperature hot rolling.The microstructure and mechanical properties under different process paramet-ers were investigated.Optical microscope,electron backscatter diffraction,and others were applied to characterize the microstructure evolution and mechanical properties strengthening mechanism.The results showed that the chemical compositions were uniformly dif-fused without segregation during sintering,and the closing of the matrix craters was accelerated by increasing the sintering temperature.The block was hot rolled at 1200℃ with an 80%reduction under only two passes without annealing.The strength and elongation of the plate at 20–25℃ after solution and aging were 1247 MPa and 14.0%,respectively,which were increased by 24.5%and 40.0%,respect-ively,compared with the as-sintered alloy at 1300℃.The microstructure was significantly refined by continuous dynamic recrystalliza-tion,which was completed by the rotation and dislocation absorption of the substructure surrounded by low-angle grain boundaries.After hot rolling combined with heat treatment,the strength and plasticity of PM-TA15 were significantly improved,which resulted from the dense,uniform,and fine recrystallization structure and the synergistic effect of multiple slip systems.
基金Project(51201014)supported by the National Natural Science Foundation of China
文摘Mechanical and shape memory properties of a Ti50Ni47Fe3 alloy annealed at 450-750 °C for 1 h after a cold-rolled reduction of 25% were investigated by phase transformation analysis and microstructure characterization using tensile tests, Vickers hardness tests, electrical resistivity-temperature tests, SEM and TEM. From the results of the tensile, it can be inferred that the fracture stress and yield stress decreased and the fracture elongation increased as the annealing temperature increased for the rolled Ti50Ni47Fe3 alloy. They reached stead values when the temperature was above 650 °C. The change in Vickers hardness corresponded to the change in the fracture stress and yield stress. The electrical resistivity-temperature curves suggest that a two- stage martensitic transformation（B2-R-B19′） occurred during cooling and heating. The transformation temperatures decreased to lower temperatures when the annealing temperature was increased and maintained the same after the annealing temperature reached 650 °C. TEM revealed the distinct processes occurring at elevated temperatures： recovery, polygonization, and recrystallization.
基金supported by the National Science and Technology Major Project(No.2011ZX05007-006)the 973 Program of China(No.2013CB228604)the major Project of Petrochina(No.2014B-0610)
文摘Ground roll waves interfere with seismic data. The suppression of ground roll waves based on the division of wavelet frequencies considers the low-frequency characteristics of ground roll waves. However, this method will not be effective when the ground roll wave and the effective signal have the same frequency bands because of overlapping. The radial trace transform （RTT） considers the apparent velocity difference between the effective signal and the ground roll wave to suppress the latter, but affects the low-frequency components of the former. This study proposes a ground roll wave suppression method by combining the wavelet frequency division and the RTT based on the difference between the ground roll wave velocity and the effective signal and their energy difference in the wavelet domain, thus making full use of the advantages of both methods. First, we decompose the seismic data into different frequency bands through wavelet transform. Second, the RTT and low-cut filtering are applied to the low-frequency band, where the ground roll waves are appearing. Third, we reconstruct the seismic record without ground roll waves by using the inverse RTT and the remaining frequency bands. The proposed method not only improves the ground roll wave suppression, but also protects the signal integrity. The numerical simulation and real seismic data processing results suggest that the proposed method has a strong ability to denoise while preserving the amplitude.
基金financial supports from the Natural Science Foundation of Shandong Province(ZR2021ME241)the Natural Science Foundation of Liaoning Province(No.2020-MS-004)+2 种基金the National Natural Science Foundation of China(NSFC,Nos.51601193 and 51701218)State Key Program of National Natural Science of China(No.51531002)National Key Research and Development Program of China(No.2016YFB0301104).
文摘3%Y_(2)O_(3)p/ZGK200 composites were subjected to unidirectional rolling(UR)and cross rolling(CR)at 400℃and 350℃followed by annealing at 300℃for 1 h.The microstructure,texture and mechanical properties of rolled and annealed composites were systematically studied.The rolled composites exhibited a heterogeneous microstructure,consisting of deformed grains elongated along rolling direction(RD)and Y_(2)O_(3)particles bands distributed along RD.After annealing,static recrystallization(SRX)occurred and most deformed grains transformed into equiaxed grains.A non-basal texture with two strong T-texture components was obtained after UR while a non-basal elliptical/circle texture with circle multi-peaks was obtained after CR,indicating that rolling path had great influences on texture of the composites.After annealing process,R-texture component disappeared or weakened,as results,a non-basal texture with double peaks tilting from normal direction(ND)to transverse direction(TD)and a more random non-basal texture with circle multi-peaks were obtained for UR and CR composites,respectively.The yield strength of rolled composites after UR showed obvious anisotropy along RD and TD while a low anisotropic yield strength was obtained after CR.Some Y_(2)O_(3)particles broke during rolling.The fracture of the composites was attributed to the existence of Y_(2)O_(3)clusters and interfacial debonding between particles and matrix during tension,as a result,the ductility was not as superior as matrix alloy.
基金This work was supported by the Postgraduate Research Innovation Project of Chongqing(CYS23217)Chongqing Modern Agricultural Industry Technology System(CQMAITS202301)+1 种基金the Science Fund for Creative Research Groups of the Natural Science Foundation of Chongqing,China(cstc2021jcyj-cxttX0004)Natural Science Foundation of Chongqing(2023NSCQ-BHX0281).
文摘A dynamic plant architecture is the basis of plant adaptation to changing environments.Although many genes regulating leaf rolling have been identified,genes directly associated with water homeostasis are largely unknown.Here,we isolated a rice mutant,dynamic leaf rolling 1(dlr1),characterized by‘leaf unfolding in the morning-leaf rolling at noon-leaf unfolding in the evening’during a sunny day.Water content was decreased in rolled leaves and water sprayed on leaves caused reopening,indicating that in vivo water deficiency induced the leaf rolling.Map-based cloning and expression tests demonstrated that an A1400G single base mutation in Oryza sativa Polygalacturonase 1(OsPG1)/PHOTO-SENSITIVE LEAF ROLLING 1(PSL1)was responsible for the dynamic leaf rolling phenotype in the dlr1 mutant.OsPG1 encodes a polygalacturonase,one of the main enzymes that degrade demethylesterified homogalacturonans in plant cell walls.OsPG1 was constitutively expressed in various tissues and was enriched in stomata.Mutants of the OsPG1 gene exhibited defects in stomatal closure and decreased stomatal density,leading to reduced transpiration and excessive water loss under specific conditions,but had normal root development.Further analysis revealed that mutation of OsPG1 led to reduced pectinase activity in the leaves and increased demethylesterified homogalacturonans in guard cells.Our findings reveal a mechanism by which OsPG1 modulates water homeostasis to control dynamic leaf rolling,providing insights for plants to adapt to environmental variation.
文摘Automobiles are the inevitable mode of transportation.However,increasing fuel prices and carbon dioxide emissions are posing a serious threat to automobile users and the environment.Thus,the development of new lightweight materials has been a key area of research.Magnesium-based commercial alloys(AZ and ZK series alloys)are the lightest among all structural metals.However,there is still a question about the replacement of Aluminum-based alloys due to HCP crystal structure.In this connection,Mg-Al-Ca-Mn(AXM)Mg alloy can be a choice as an alternative to the existing Mg-based commercial alloys for structural applications.It contains(Al,Mg)_(2)Ca,Al_(2)Ca,Mg_(2)Ca,and Al_(8)Mn_(5)as the secondary phases,contributing to the microstructural refinement and property enhancement.However,the formation of those precipitates depends on the amount of Al,Ca,and Mn,especially,the Ca/Al ratio.In addition,the secondary processes influence the grain refinement and property enhancement of texture modifications.Hence,this review article focuses on elaborating on the significance of the Ca/Al ratio for the precipitate formation,secondary process,and texture modifications.The co-segregation behavior of other micro-alloying elements like Cerium,Lanthanum,and Zinc in AXM Mg alloy systems has also been discussed for property enhancement.
基金Projects(52274404,52305441,U22A20190)supported by the National Natural Science Foundation of ChinaProjects(2022JJ20065,2023JJ40739)supported by the Natural Science Foundation of Hunan Province,China+2 种基金Project(2022RC1001)supported by the Science and Technology Innovation Program of Hunan Province,ChinaProject(2023ZZTS0972)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2021YFB3400903)supported by the National Key R&D Program of China。
文摘The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formability of Al-Cu-Li alloy is vital.A thorough comparison of the effects of cryo-deformation and ambient temperature large pre-deformation(LPD)on the creep ageing response in the 2195 alloy sheet at 160℃with different stresses has been made.The evolution of dislocations and precipitates during creep ageing of LPD alloys are revealed by X-ray diffraction and transmission electron microscopy.High-quality 2195 alloy sheet largely pre-deformed by 80%without edge-cracking is obtained by cryo-rolling at liquid nitrogen temperature,while severe edge-cracking occurs during room temperature rolling.The creep formability and strength of the 2195 alloy are both enhanced by introducing pre-existing dislocations with a density over 1.4×10^(15)m^(−2).At 160℃and 150 MPa,creep strain and creep-aged strength generally increases by 4−6 times and 30−50 MPa in the LPD sample,respectively,compared to conventional T3 alloy counterpart.The elongation of creep-aged LPD sample is low but remains relevant for application.The high-density dislocations,though existing in the form of dislocation tangles,promote the formation of refined T1 precipitates with a uniform dispersion.
