This paper demonstrates the analysis of antenna pattern and gain for different designs of full-wave dipole antenna feeding techniques. Seven such techniques were studied and analyzed;symmetrical dual feeding in phase,...This paper demonstrates the analysis of antenna pattern and gain for different designs of full-wave dipole antenna feeding techniques. Seven such techniques were studied and analyzed;symmetrical dual feeding in phase, symmetrical dual feeding out of phase, asymmetrical dual feeding in phase, asymmetrical dual feeding out of phase, symmetrical triple feeding in phase and symmetrical triple feeding out of phase. Symmetrical dual feeding in phase produced high gain as compared to the single and center-fed antennas. An improvement of about 3 to 3.5 dB was achieved comparing to center tap fed and off center fed. It was found that an asymmetrical dual feeding in-phase provides good performance, considering the directivity, pattern, and input impedance. A 2.46 dB gain has been attained. It was found that a symmetrical triple feeding provides an overall best performance with respect to gain, radiation pattern, beam width and input impedance.展开更多
Printed-circuit board (PCB) elliptic antennas with useful bandwidth exceeding 10:1 ratio are suitable for wideband radar, wireless ultra wideband (UWB) and other wireless communication applications. We present wideban...Printed-circuit board (PCB) elliptic antennas with useful bandwidth exceeding 10:1 ratio are suitable for wideband radar, wireless ultra wideband (UWB) and other wireless communication applications. We present wideband PCB elliptic dipole antennas which are capable of achieving the bandwidth requirements for all the applications. A set of elliptic dipole antennas with varying eccentricities have been fabricated for demonstration. We find one specific size (specific eccentricity) dipole that can yield an impressive 1.5-16 bandwidth exceeding the currently available. A couple of elliptic dipole antennas suitable for UWB application have been presented. We have measured swept frequency response, impedance and radiation patterns of all dipoles. An empirical formula is given for calculating the starting resonant frequency within the operating band. The calculated values are found in good agreement with measured results.展开更多
A rectangle capacity patch was adopted as the resonance unit of the Log Periodic Dipole Antenna (LPDA) so as to realize the miniaturization of this aerial in this paper. Fifteen rectangle capacity patch units of diffe...A rectangle capacity patch was adopted as the resonance unit of the Log Periodic Dipole Antenna (LPDA) so as to realize the miniaturization of this aerial in this paper. Fifteen rectangle capacity patch units of different parameters were analyzed in this paper and three design laws of size-reduction were found. Accord-ing to these design laws, a 70% miniaturization ratio LPDA was designed and fabricated. The Voltage Standing Wave Ratio (VSWR) and pattern of the fabricated LPDA were measured. The results indicate that this size-reduction method do not deteriorate performance.展开更多
A novel metasurface antenna consisting of 5×5 rectangular patch elements is presented.Thestructure with and without the central element are both analyzed by the Characteristic Mode Theory(CMT).The developed mutua...A novel metasurface antenna consisting of 5×5 rectangular patch elements is presented.Thestructure with and without the central element are both analyzed by the Characteristic Mode Theory(CMT).The developed mutually orthogonal principal modes of the optimized periodic patch structure areexcited by a center-feed dipole.A differential feeding network is employed to realize impedance matching.Prototype with profile height of 0.07λ_(0)(λ_(0)is the wavelength in free space at the lowest operatingfrequency)is fabricated and assembled to verify the simulation results.The measured results show that thereflectance coefficient of proposed matesurface antenna is less than-10 dB in the whole operating bandrange from 4.2 GHz to 5.5 GHz,a relative bandwidth of 26.8%is achieved,and the maximummeasured realized gain is more than 9 dBi with a maximum radiation efficiency of 90%.The designprovides a guideline on the application of characteristic modes(CMs)to radiation problems.展开更多
A dipole antenna with wideband characteristics is presented. The proposed antenna consists of a dipole with periodic capacitive loading and a pair of coplanar striplines （CPSs） as an impedance transformer. By adding...A dipole antenna with wideband characteristics is presented. The proposed antenna consists of a dipole with periodic capacitive loading and a pair of coplanar striplines （CPSs） as an impedance transformer. By adding interlaced coupling lines at each section, periodic capacitive loading is realized. The periodic interlaced coupling lines divide each arm of the dipole into five sections, and currents are distributed on different sections at different frequencies, which is useful to achieve a wide impedance bandwidth. By parametric study using HFSS, the optimized parameters of this dipole antenna are obtained. In order to validate the simulation results, a prototype of the proposed dipole antenna is fabricated and tested. The results show that the proposed antenna can achieve a gain of 3.1 dB–5.1 dB and bandwidth of 51% for ｜S 11 ｜ 10 dB over the band of 3.9 GHz–6.6 GHz, indicating its good radiation performance and radiation efficiency.展开更多
A novel balun structure for dipole antenna,which is based on the current distribution on parallel microstrip lines and the emission cancellation characteristic of close equal and opposite currents,is proposed.The prin...A novel balun structure for dipole antenna,which is based on the current distribution on parallel microstrip lines and the emission cancellation characteristic of close equal and opposite currents,is proposed.The principle of the balun structure is first elaborated and verified.Then,a dipole antenna with resonance at 2.45 GHz is constructed using the balun and its radiation pattern is measured.The simulated and measured reflection coefficients(S_(11))of the antenna are in good agreement 2—3 GHz.The relative bandwidth with an S_(11) of below-10 dB is more than 25%.The antenna also shows a good radiation pattern at 2.45 GHz.The proposed structure can provide a new balun design method for dipole antennas.展开更多
Based on the calculation of the characteristic parameters by moment method, the curved surface dipoles are optimized by an optimization method, the maximum directivities of some V-curved and Gauss-curved surface dipol...Based on the calculation of the characteristic parameters by moment method, the curved surface dipoles are optimized by an optimization method, the maximum directivities of some V-curved and Gauss-curved surface dipoles are given.展开更多
The problem for calculating near fields of EM radiation systems by using the finitedifference time domain(FD-TD)method are discussed and the annular phased array of dipoleantennas has been simulated numerically by use...The problem for calculating near fields of EM radiation systems by using the finitedifference time domain(FD-TD)method are discussed and the annular phased array of dipoleantennas has been simulated numerically by use of the FD-TD method.For a test run thenear field and current distribution of the single dipole antenna are calculated.The near fieldsof the annular phased array of dipole antennas in central region filled with deionized water arecomputed and the interaction of near fields with an anatomically-based inhomogeneous model ofhuman torso is considered as well.展开更多
The magneto-electric dipole antenna is a kind of complementary antenna composed of a planar electric dipole and a shorted patch antenna. It has excellent electrical characteristics including wide impedance bandwidth, ...The magneto-electric dipole antenna is a kind of complementary antenna composed of a planar electric dipole and a shorted patch antenna. It has excellent electrical characteristics including wide impedance bandwidth, low cross-polarization, low back lobe radiation, nearly identical E-plane and H-plane patterns, stable radiation pattern, and steady antenna gain over the operating frequency range. In this paper, the basic characteristics of a linearly polarized magneto-electric dipole antenna are reviewed, and a dual-polarized antenna element based on the magneto-electric dipole is presented. The design of a conical beam wideband antenna with horizontal polarization is also described. These antennas have practical applications in modern 2G, 3G, LTE, WiFi, and WiMax wireless communication systems.展开更多
The formula of input impedance of dipole antenna in Gigahertz Transverse ElectroM agnetic(GTEM) cell based on the dyadic Green's function is first obtained in this paper. The validation of the formula is verified ...The formula of input impedance of dipole antenna in Gigahertz Transverse ElectroM agnetic(GTEM) cell based on the dyadic Green's function is first obtained in this paper. The validation of the formula is verified by the results of theoretical derivation and simulation with well agreements. In comparison with the formula of input impedance in free space, the relationship between the change of input impedance with the length of antenna and the position of antenna in GTEM cell is obtained. In addition, some meaningful conclusions are presented, which not only can be referred by the further research of ElectroM agnetic Interference(EMI) measurements in GTEM cell, but also provide the theoretical basis for testing compensation and error analysis.展开更多
The microfabrication technique for THz dipole antenna,"lift-off" was studied in this paper.Its procedure has been examined in detail,and discreetly tweaked.Particularly,Chlorobenzene is suggested to assist t...The microfabrication technique for THz dipole antenna,"lift-off" was studied in this paper.Its procedure has been examined in detail,and discreetly tweaked.Particularly,Chlorobenzene is suggested to assist the formation of undercut indispensible for fulfilling "lift-off".The experimental results of fabricated antennas confirm the effectiveness of this method.展开更多
This paper proposes a printed log-periodic dipole antenna (LPDA) for ultra wide bandwidth (UWB) applications. The antenna comprises of cascading four U shaped elements of different line lengths with balun circuit to i...This paper proposes a printed log-periodic dipole antenna (LPDA) for ultra wide bandwidth (UWB) applications. The antenna comprises of cascading four U shaped elements of different line lengths with balun circuit to improve the antenna impedance matching. The proposed antenna dimensions are 50 × 50 mm2 with FR4 substrate thickness 0.8 mm. Full-wave EM solver HFSS (High Frequency Structure Simulator) is used for modeling the proposed antenna. The pulse distortion is verified by the measured the proposed antenna performance with virtually steady group delay. The simulation and experimental results show that the proposed antenna exhibits good impedance matching, stable radiation patterns throughout the whole operating frequency bands, acceptable gain and stable group delay over the entire operating band. An UWB extended from 1.85 GHz to 11 GHz is obtained, and the average antenna gain is about 5.5 dBi over the operating band with peak gain around 6.5 dBi and 70% average radiation efficiency.展开更多
In this paper, a number of reconfigurable antennas are designed to support multiband and wideband wireless applications in different frequency bands in the range between 1 GHz and 6 GHz. The proposed designs consist o...In this paper, a number of reconfigurable antennas are designed to support multiband and wideband wireless applications in different frequency bands in the range between 1 GHz and 6 GHz. The proposed designs consist of microstrip-fed two dipoles through simplified balun. By controlling the lengths of the dipoles by connecting or disconnecting slots, we are able to change the antenna operating frequency as well as the operation mode. Two modes are supported by all of the proposed antennas: Multiband and Broadband modes.展开更多
Subwavelength arrays of dipole-bowtie antennas are designed and characterized using terahertz time-domain spectroscopy（THz-TDS） and finite element method（FEM） simulations. Two different substrates, silicon and myl...Subwavelength arrays of dipole-bowtie antennas are designed and characterized using terahertz time-domain spectroscopy（THz-TDS） and finite element method（FEM） simulations. Two different substrates, silicon and mylar with an order of magnitude difference between their thickness values are used to study the resonance properties of the antennas.The 640-μm thick silicon substrate supports a sharper fundamental mode resonance. We discover that higher-order Fabry–Perot resonances can be excited only in 24-μm thin mylar substrates and show much higher sensitivity to dielectric changes in the environment and the geometrical parameters of the antennas than the fundamental dipole resonance.展开更多
文摘This paper demonstrates the analysis of antenna pattern and gain for different designs of full-wave dipole antenna feeding techniques. Seven such techniques were studied and analyzed;symmetrical dual feeding in phase, symmetrical dual feeding out of phase, asymmetrical dual feeding in phase, asymmetrical dual feeding out of phase, symmetrical triple feeding in phase and symmetrical triple feeding out of phase. Symmetrical dual feeding in phase produced high gain as compared to the single and center-fed antennas. An improvement of about 3 to 3.5 dB was achieved comparing to center tap fed and off center fed. It was found that an asymmetrical dual feeding in-phase provides good performance, considering the directivity, pattern, and input impedance. A 2.46 dB gain has been attained. It was found that a symmetrical triple feeding provides an overall best performance with respect to gain, radiation pattern, beam width and input impedance.
文摘Printed-circuit board (PCB) elliptic antennas with useful bandwidth exceeding 10:1 ratio are suitable for wideband radar, wireless ultra wideband (UWB) and other wireless communication applications. We present wideband PCB elliptic dipole antennas which are capable of achieving the bandwidth requirements for all the applications. A set of elliptic dipole antennas with varying eccentricities have been fabricated for demonstration. We find one specific size (specific eccentricity) dipole that can yield an impressive 1.5-16 bandwidth exceeding the currently available. A couple of elliptic dipole antennas suitable for UWB application have been presented. We have measured swept frequency response, impedance and radiation patterns of all dipoles. An empirical formula is given for calculating the starting resonant frequency within the operating band. The calculated values are found in good agreement with measured results.
文摘A rectangle capacity patch was adopted as the resonance unit of the Log Periodic Dipole Antenna (LPDA) so as to realize the miniaturization of this aerial in this paper. Fifteen rectangle capacity patch units of different parameters were analyzed in this paper and three design laws of size-reduction were found. Accord-ing to these design laws, a 70% miniaturization ratio LPDA was designed and fabricated. The Voltage Standing Wave Ratio (VSWR) and pattern of the fabricated LPDA were measured. The results indicate that this size-reduction method do not deteriorate performance.
文摘A novel metasurface antenna consisting of 5×5 rectangular patch elements is presented.Thestructure with and without the central element are both analyzed by the Characteristic Mode Theory(CMT).The developed mutually orthogonal principal modes of the optimized periodic patch structure areexcited by a center-feed dipole.A differential feeding network is employed to realize impedance matching.Prototype with profile height of 0.07λ_(0)(λ_(0)is the wavelength in free space at the lowest operatingfrequency)is fabricated and assembled to verify the simulation results.The measured results show that thereflectance coefficient of proposed matesurface antenna is less than-10 dB in the whole operating bandrange from 4.2 GHz to 5.5 GHz,a relative bandwidth of 26.8%is achieved,and the maximummeasured realized gain is more than 9 dBi with a maximum radiation efficiency of 90%.The designprovides a guideline on the application of characteristic modes(CMs)to radiation problems.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 61172115 and 60872029)the High-Tech Research and Development Program of China (Grant No. 2008AA01Z206)the Aeronautics Foundation of China (Grant No. 20100180003)
文摘A dipole antenna with wideband characteristics is presented. The proposed antenna consists of a dipole with periodic capacitive loading and a pair of coplanar striplines （CPSs） as an impedance transformer. By adding interlaced coupling lines at each section, periodic capacitive loading is realized. The periodic interlaced coupling lines divide each arm of the dipole into five sections, and currents are distributed on different sections at different frequencies, which is useful to achieve a wide impedance bandwidth. By parametric study using HFSS, the optimized parameters of this dipole antenna are obtained. In order to validate the simulation results, a prototype of the proposed dipole antenna is fabricated and tested. The results show that the proposed antenna can achieve a gain of 3.1 dB–5.1 dB and bandwidth of 51% for ｜S 11 ｜ 10 dB over the band of 3.9 GHz–6.6 GHz, indicating its good radiation performance and radiation efficiency.
基金supported by the Fundamental Research Funds for the Central Universities (No. 30920140122005)the Research Innovation Program for College Graduates of Jiangsu Province (No.CXLX11_ 0198)
文摘A novel balun structure for dipole antenna,which is based on the current distribution on parallel microstrip lines and the emission cancellation characteristic of close equal and opposite currents,is proposed.The principle of the balun structure is first elaborated and verified.Then,a dipole antenna with resonance at 2.45 GHz is constructed using the balun and its radiation pattern is measured.The simulated and measured reflection coefficients(S_(11))of the antenna are in good agreement 2—3 GHz.The relative bandwidth with an S_(11) of below-10 dB is more than 25%.The antenna also shows a good radiation pattern at 2.45 GHz.The proposed structure can provide a new balun design method for dipole antennas.
文摘Based on the calculation of the characteristic parameters by moment method, the curved surface dipoles are optimized by an optimization method, the maximum directivities of some V-curved and Gauss-curved surface dipoles are given.
文摘The problem for calculating near fields of EM radiation systems by using the finitedifference time domain(FD-TD)method are discussed and the annular phased array of dipoleantennas has been simulated numerically by use of the FD-TD method.For a test run thenear field and current distribution of the single dipole antenna are calculated.The near fieldsof the annular phased array of dipole antennas in central region filled with deionized water arecomputed and the interaction of near fields with an anatomically-based inhomogeneous model ofhuman torso is considered as well.
文摘The magneto-electric dipole antenna is a kind of complementary antenna composed of a planar electric dipole and a shorted patch antenna. It has excellent electrical characteristics including wide impedance bandwidth, low cross-polarization, low back lobe radiation, nearly identical E-plane and H-plane patterns, stable radiation pattern, and steady antenna gain over the operating frequency range. In this paper, the basic characteristics of a linearly polarized magneto-electric dipole antenna are reviewed, and a dual-polarized antenna element based on the magneto-electric dipole is presented. The design of a conical beam wideband antenna with horizontal polarization is also described. These antennas have practical applications in modern 2G, 3G, LTE, WiFi, and WiMax wireless communication systems.
基金Supported by Chinese Academy of Sciences(No.Y140110213)
文摘The formula of input impedance of dipole antenna in Gigahertz Transverse ElectroM agnetic(GTEM) cell based on the dyadic Green's function is first obtained in this paper. The validation of the formula is verified by the results of theoretical derivation and simulation with well agreements. In comparison with the formula of input impedance in free space, the relationship between the change of input impedance with the length of antenna and the position of antenna in GTEM cell is obtained. In addition, some meaningful conclusions are presented, which not only can be referred by the further research of ElectroM agnetic Interference(EMI) measurements in GTEM cell, but also provide the theoretical basis for testing compensation and error analysis.
文摘The microfabrication technique for THz dipole antenna,"lift-off" was studied in this paper.Its procedure has been examined in detail,and discreetly tweaked.Particularly,Chlorobenzene is suggested to assist the formation of undercut indispensible for fulfilling "lift-off".The experimental results of fabricated antennas confirm the effectiveness of this method.
文摘This paper proposes a printed log-periodic dipole antenna (LPDA) for ultra wide bandwidth (UWB) applications. The antenna comprises of cascading four U shaped elements of different line lengths with balun circuit to improve the antenna impedance matching. The proposed antenna dimensions are 50 × 50 mm2 with FR4 substrate thickness 0.8 mm. Full-wave EM solver HFSS (High Frequency Structure Simulator) is used for modeling the proposed antenna. The pulse distortion is verified by the measured the proposed antenna performance with virtually steady group delay. The simulation and experimental results show that the proposed antenna exhibits good impedance matching, stable radiation patterns throughout the whole operating frequency bands, acceptable gain and stable group delay over the entire operating band. An UWB extended from 1.85 GHz to 11 GHz is obtained, and the average antenna gain is about 5.5 dBi over the operating band with peak gain around 6.5 dBi and 70% average radiation efficiency.
文摘In this paper, a number of reconfigurable antennas are designed to support multiband and wideband wireless applications in different frequency bands in the range between 1 GHz and 6 GHz. The proposed designs consist of microstrip-fed two dipoles through simplified balun. By controlling the lengths of the dipoles by connecting or disconnecting slots, we are able to change the antenna operating frequency as well as the operation mode. Two modes are supported by all of the proposed antennas: Multiband and Broadband modes.
基金Project partly supported by the National Natural Science Foundation of China(Grant Nos.11104360,11204191,and 11374378)the National Special Fund for the Development of Major Research Equipment and Instruments,China(Grant No.2012YQ14000508)the Technology Foundation for Selected Overseas Chinese Scholar
文摘Subwavelength arrays of dipole-bowtie antennas are designed and characterized using terahertz time-domain spectroscopy（THz-TDS） and finite element method（FEM） simulations. Two different substrates, silicon and mylar with an order of magnitude difference between their thickness values are used to study the resonance properties of the antennas.The 640-μm thick silicon substrate supports a sharper fundamental mode resonance. We discover that higher-order Fabry–Perot resonances can be excited only in 24-μm thin mylar substrates and show much higher sensitivity to dielectric changes in the environment and the geometrical parameters of the antennas than the fundamental dipole resonance.
