The isothermal grain growth behavior for a new ultrahigh-strength stainless steel (UHSSS) is investigated in temperature range from 900 to 1150 ℃ and holding time range from 0 to 20 min. In the temperature range from...The isothermal grain growth behavior for a new ultrahigh-strength stainless steel (UHSSS) is investigated in temperature range from 900 to 1150 ℃ and holding time range from 0 to 20 min. In the temperature range from 1000 to 1050 ℃, a bimodal grain size distribution was induced by different austenite grain growth rates which resulted from the weakened pin-ning effect by the partial dissolution of M6C particles along austenite grain boundaries. Further raising heating temperatures, M6C particles almost dissolved and the bimodal grain size distribution phenomenon became weakened, indicating that the austenite grain coarsening temperature of the new UHSSS was close to 1050 ℃. According to the present experimental results, a pragmatic mathematical model based on the Arrhenius equations was developed to predict the austenite grain growth process, which elaborated the influence of heating temperature, holding time and initial grain size on the austenite grain growth. Predictions for the new UHSSS presented a good agreement with experimental results.展开更多
The low carbon Nb-Ti mieroalloyed tested steel was prepared by the process of vacuum induction furnace smelting, forging and hot rolling. The new steel aims to meet the demand of high strength, high toughness and high...The low carbon Nb-Ti mieroalloyed tested steel was prepared by the process of vacuum induction furnace smelting, forging and hot rolling. The new steel aims to meet the demand of high strength, high toughness and high plasticity for building facilities. The effects of quenching process on microstructure and mechanical properties of tested steel were investigated. The results showed that prior austenite grain size, phase type and precipitation behavior of （ Nb, Ti） （ C, N） play important roles in mechanical properties of the steel. Through modified appropriately, the model of austenite grain growth during heating and holding is d^5.7778 = 5. 6478^5.7778 ＋ 7.04 × 10^22t^1.6136 exp（- 427. 15 ×10^3 /（RT））. The grain growth activation energy is Qg = 427. 15 kJ. During quenching, the microscopic structures are mainly martensite and lath bainite which contains lots of lath substructure and dislocations. The content of phases, fine and coarsening （ Nb, Ti ） （ C, N ） precipitated changes during different quenching temperatures and holding time. Finally compared with the hardness value, the best quenching process can be obtained that heating temperature and holding time are 900 ℃ and 50 mins, respectively.展开更多
Niobium has an important effect on the transformation behaviour,grain size refinement and precipitation strengthening during hot rolling and subsequent cooling in low carbon steels,with even a low content of niobium h...Niobium has an important effect on the transformation behaviour,grain size refinement and precipitation strengthening during hot rolling and subsequent cooling in low carbon steels,with even a low content of niobium having a strong effect on the transformation rate from austenite to ferrite.However,the effects of niobium on transformation behaviour have not been fully characterised and understood to date.This paper examines in detail austenite grain growth as a function of austenitisation time in high strength low alloy (HSLA) steels with three different niobium contents,together with the effect of niobium on the isothermal transformation kinetics from austenite to ferrite as a function of temperature.It is shown that austenite has the slowest grain growth rate in the steel with the highest niobium content.When austenite grain sizes are consistent,the steel with the highest niobium content was found to have the slowest transformation rate from austenite to ferrite.展开更多
The austenitization behaviors of two high niohium-containing X80 pipeline steels with different titanium contents, including the dissolution of microalloying precipitates and the austenite grain growth, were investiga...The austenitization behaviors of two high niohium-containing X80 pipeline steels with different titanium contents, including the dissolution of microalloying precipitates and the austenite grain growth, were investigated by using physical-chemical phase analysis method and microstructural observation. The results illustrated that most niobium could be dissolved into austenite during soaking at 1 180 ℃, whereas little amount of titanium could be dissolved. It was found that during soaking, the austenite grain growth rate was initially high, and then decreased after soaking for 1 h; moreover, the austenite grains grew up more rapidly at temperatures above 1 180 ℃ than below 1 180 ℃. The results show that the steel with titanium content of 0. 016% has a larger austenite grain size than that with titanium content of 0. 012% under the same soaking conditions, which is explained by considering the particle size distribution.展开更多
The RAFM（reduced activation ferritic/martensitic）steels containing different tantalum contents（0wt.%,0.027wt.%,0.073wt.%）were designed and cast.Differential scanning calorimetry and optical microscopy were employe...The RAFM（reduced activation ferritic/martensitic）steels containing different tantalum contents（0wt.%,0.027wt.%,0.073wt.%）were designed and cast.Differential scanning calorimetry and optical microscopy were employed to explore the influence of tantalum content on the austenitic transformation of RAFM steels.The austenitic transformation kinetics was described by aphase-transformation model.The model,involving site saturation nucleation,diffusion-controlled growth and impingement correction,was established based on the classical Johnson-Mehl-Avrami-Kolmogorov model.The phase-transformation kinetics parameters,including D_0（pre-exponential factor for diffusion）and Q_d（activation energy for diffusion）,were calculated by fitting the experimental data and the kinetic model.The results indicated that the average grain size is decreased with the increase of tantalum.The values of A_（c1） and A_（c3） （onset and finish temperature of austenitic transformation,respectively）are increased by increasing the tantalum content.The increase of tantalum caused the decrease of D_0.However,Q_d is increased with the increase of tantalum.In addition,as a carbides forming element,tantalum would reduce the carbon diffusion coefficient and slow down the austenitic transformation rate.展开更多
基金The authors gratefully acknowledge the support from the National Key Research and Development Program of China(2016YFB0300104).
文摘The isothermal grain growth behavior for a new ultrahigh-strength stainless steel (UHSSS) is investigated in temperature range from 900 to 1150 ℃ and holding time range from 0 to 20 min. In the temperature range from 1000 to 1050 ℃, a bimodal grain size distribution was induced by different austenite grain growth rates which resulted from the weakened pin-ning effect by the partial dissolution of M6C particles along austenite grain boundaries. Further raising heating temperatures, M6C particles almost dissolved and the bimodal grain size distribution phenomenon became weakened, indicating that the austenite grain coarsening temperature of the new UHSSS was close to 1050 ℃. According to the present experimental results, a pragmatic mathematical model based on the Arrhenius equations was developed to predict the austenite grain growth process, which elaborated the influence of heating temperature, holding time and initial grain size on the austenite grain growth. Predictions for the new UHSSS presented a good agreement with experimental results.
基金Sponsored by the Major State Basic Research Development Program of China(Grant No.2010CB630801)
文摘The low carbon Nb-Ti mieroalloyed tested steel was prepared by the process of vacuum induction furnace smelting, forging and hot rolling. The new steel aims to meet the demand of high strength, high toughness and high plasticity for building facilities. The effects of quenching process on microstructure and mechanical properties of tested steel were investigated. The results showed that prior austenite grain size, phase type and precipitation behavior of （ Nb, Ti） （ C, N） play important roles in mechanical properties of the steel. Through modified appropriately, the model of austenite grain growth during heating and holding is d^5.7778 = 5. 6478^5.7778 ＋ 7.04 × 10^22t^1.6136 exp（- 427. 15 ×10^3 /（RT））. The grain growth activation energy is Qg = 427. 15 kJ. During quenching, the microscopic structures are mainly martensite and lath bainite which contains lots of lath substructure and dislocations. The content of phases, fine and coarsening （ Nb, Ti ） （ C, N ） precipitated changes during different quenching temperatures and holding time. Finally compared with the hardness value, the best quenching process can be obtained that heating temperature and holding time are 900 ℃ and 50 mins, respectively.
文摘Niobium has an important effect on the transformation behaviour,grain size refinement and precipitation strengthening during hot rolling and subsequent cooling in low carbon steels,with even a low content of niobium having a strong effect on the transformation rate from austenite to ferrite.However,the effects of niobium on transformation behaviour have not been fully characterised and understood to date.This paper examines in detail austenite grain growth as a function of austenitisation time in high strength low alloy (HSLA) steels with three different niobium contents,together with the effect of niobium on the isothermal transformation kinetics from austenite to ferrite as a function of temperature.It is shown that austenite has the slowest grain growth rate in the steel with the highest niobium content.When austenite grain sizes are consistent,the steel with the highest niobium content was found to have the slowest transformation rate from austenite to ferrite.
基金Item Sponsored by National Key Technologies Research and Development Program of China(2006BAE03A15)
文摘The austenitization behaviors of two high niohium-containing X80 pipeline steels with different titanium contents, including the dissolution of microalloying precipitates and the austenite grain growth, were investigated by using physical-chemical phase analysis method and microstructural observation. The results illustrated that most niobium could be dissolved into austenite during soaking at 1 180 ℃, whereas little amount of titanium could be dissolved. It was found that during soaking, the austenite grain growth rate was initially high, and then decreased after soaking for 1 h; moreover, the austenite grains grew up more rapidly at temperatures above 1 180 ℃ than below 1 180 ℃. The results show that the steel with titanium content of 0. 016% has a larger austenite grain size than that with titanium content of 0. 012% under the same soaking conditions, which is explained by considering the particle size distribution.
基金financially sponsored by the China National Funds for Distinguished Young Scientists (Granted No.51325401)the National Natural Science Foundation of China(Granted No.51501126)the National Magnetic Confinement Fusion Energy Research Program(Granted No.2015GB119001)
文摘The RAFM（reduced activation ferritic/martensitic）steels containing different tantalum contents（0wt.%,0.027wt.%,0.073wt.%）were designed and cast.Differential scanning calorimetry and optical microscopy were employed to explore the influence of tantalum content on the austenitic transformation of RAFM steels.The austenitic transformation kinetics was described by aphase-transformation model.The model,involving site saturation nucleation,diffusion-controlled growth and impingement correction,was established based on the classical Johnson-Mehl-Avrami-Kolmogorov model.The phase-transformation kinetics parameters,including D_0（pre-exponential factor for diffusion）and Q_d（activation energy for diffusion）,were calculated by fitting the experimental data and the kinetic model.The results indicated that the average grain size is decreased with the increase of tantalum.The values of A_（c1） and A_（c3） （onset and finish temperature of austenitic transformation,respectively）are increased by increasing the tantalum content.The increase of tantalum caused the decrease of D_0.However,Q_d is increased with the increase of tantalum.In addition,as a carbides forming element,tantalum would reduce the carbon diffusion coefficient and slow down the austenitic transformation rate.
