Data organization requires high efficiency for large amount of data applied in the digital mine system. A new method of storing massive data of block model is proposed to meet the characteristics of the database, incl...Data organization requires high efficiency for large amount of data applied in the digital mine system. A new method of storing massive data of block model is proposed to meet the characteristics of the database, including ACID-compliant, concurrency support, data sharing, and efficient access. Each block model is organized by linear octree, stored in LMDB（lightning memory-mapped database）. Geological attribute can be queried at any point of 3D space by comparison algorithm of location code and conversion algorithm from address code of geometry space to location code of storage. The performance and robustness of querying geological attribute at 3D spatial region are enhanced greatly by the transformation from 3D to 2D and the method of 2D grid scanning to screen the inner and outer points. Experimental results showed that this method can access the massive data of block model, meeting the database characteristics. The method with LMDB is at least 3 times faster than that with etree, especially when it is used to read. In addition, the larger the amount of data is processed, the more efficient the method would be.展开更多
Recently published results of field and laboratory experiments on the seismic/acoustic response to injection of direct current （DC） pulses into the Earth crust or stressed rock samples raised a question on a possibi...Recently published results of field and laboratory experiments on the seismic/acoustic response to injection of direct current （DC） pulses into the Earth crust or stressed rock samples raised a question on a possibility of electrical earthquake triggering. A physical mechanism of the considered phenomenon is not clear yet in view of the very low current density （10-7-10-s A/m^2） generated by the pulsed power systems at the epicenter depth （5-10 km） of local earthquakes occurred just after the current injection. The paper describes results of laboratory ＂earthquake＂ triggering by DC pulses under conditions of a spring-block model simulated the seismogenic fault. It is experimentally shown that the electric triggering of the laboratory ＂earthquake＂ （sharp slip of a movable block of the spring-block system） is possible only within a range of subcritical state of the system, when the shear stress between the movable and fixed blocks obtains 0.98-0.99 of its critical value. The threshold of electric triggering action is about 20 A/m^2 that is 7-8 orders of magnitude higher than estimated electric current density for Bishkek test site （Northern Tien Shan, Kirghizia） where the seismic response to the man-made electric action was observed. In this connection, the electric triggering phenomena may be explained by contraction of electric current in the narrow conductive areas of the faults and the corresponding increase in current density or by involving the secondary triggering mechanisms like electromagnetic stimulation of conductive fluid migration into the fault area resulted in decrease in the fault strength properties.展开更多
In this research, a method called ANNMG is presented to integrate Artificial Neural Networks and Geostatistics for optimum mineral reserve evaluation. The word ANNMG simply means Artificial Neural Network Model integr...In this research, a method called ANNMG is presented to integrate Artificial Neural Networks and Geostatistics for optimum mineral reserve evaluation. The word ANNMG simply means Artificial Neural Network Model integrated with Geostatiscs, In this procedure, the Artificial Neural Network was trained, tested and validated using assay values obtained from exploratory drillholes. Next, the validated model was used to generalize mineral grades at known and unknown sampled locations inside the drilling region respectively. Finally, the reproduced and generalized assay values were combined and fed to geostatistics in order to develop a geological 3D block model. The regression analysis revealed that the predicted sample grades were in close proximity to the actual sample grades, The generalized grades from the ANNMG show that this process could be used to complement exploration activities thereby reducing drilling requirement. It could also be an effective mineral reserve evaluation method that could oroduce optimum block model for mine design.展开更多
Bonded blockmodel(BBM)has shownpotential in replicating rockmass behavior aswell as the rockesupport interactionmechanism,but their practical application is limited totwo dimensions due to the high associated computat...Bonded blockmodel(BBM)has shownpotential in replicating rockmass behavior aswell as the rockesupport interactionmechanism,but their practical application is limited totwo dimensions due to the high associated computational demand.To allow for the use of BBM in simulating three-dimensional(3D)problems,this study proposes an integrated 3D continuumetwo-dimensional(2D)discontinuum approach,in context of rock pillars.A cross-section of a granite pillar was simulated using a BBM with a load path from a calibrated mine-scale FLAC^(3D)model.Pillar support as employed in the mine was also incorporated in different stages during the simulation.Themodel was calibrated by varying the input parameters until the displacements at six locations within the pillarmatchedthosemeasuredby amulti-point borehole extensometer(MPBX)inthe field.The calibratedmodel was subsequently used to understand how the support and load path influenced the damage evolution in the pillar.The shear component of the load pathwas found to have amajor effect on the severity and extent of the damaged regions.When the support density was increased in the model,the lateral displacements along the pillar walls were significantly suppressed in a somewhat unpredictable manner.Thiswas explained by the interaction between the supports and the damaged regions at the corners,which ultimately modified the stresses along the pillar periphery.The amount of displacement reduction obtained by increasing the support density illustrates the potential of BBMto be used as a support design tool.展开更多
The solid block model is applied to describe the motion of the pyroclastic flow under the joint action of gravity and Coulomb friction. Special attention is paid to characteristics of the pyroclastic flow generated by...The solid block model is applied to describe the motion of the pyroclastic flow under the joint action of gravity and Coulomb friction. Special attention is paid to characteristics of the pyroclastic flow generated by Montserrat volcano in likely directions. The critical friction angle of the flow propagation is evaluated empirically. Characteristic parameters of the pyroclastic flow (travel time and impact velocity) are well approximated by linear regressions. Proposed estimations of the parameters of pyroclastic flow are useful for the rough and express evaluation of its characteristics.展开更多
Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid...Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid environments are not mastered. This article evaluates the influence of architectural and constructive modes of buildings made of CEB walls and concrete block walls, to optimize and compare their thermal comfort in the hot and dry tropical climate of Ouagadougou, Burkina Faso. Two identical pilot buildings whose envelopes are made of CEB and concrete blocks were monitored for this study. The thermal models of the pilot buildings were implemented in the SketchUp software using an extension of EnergyPlus. The models were empirically validated after calibration against measured thermal data from the buildings. The models were used to do a parametric analysis for optimization of the thermal performances by simulating plaster coatings on the exterior of walls, airtight openings and natural ventilation depending on external weather conditions. The results show that the CEB building displays 7016 hours of discomfort, equivalent to 80.1% of the time, and the concrete building displays 6948 hours of discomfort, equivalent to 79.3% of the time. The optimization by modifications reduced the discomfort to 2918 and 3125 hours respectively;i.e. equivalent to only 33.3% for the CEB building and 35.7% for the concrete building. More study should evaluate thermal optimizations in buildings in real time of usage such as residential buildings commonly used by the local middle class. The use of CEB as a construction material and passive means of improving thermal comfort is a suitable ecological and economical option to replace cementitious material.展开更多
In this paper,to obtain a consistent estimator of the number of communities,the authors present a new sequential testing procedure,based on the locally smoothed adjacency matrix and the extreme value theory.Under the ...In this paper,to obtain a consistent estimator of the number of communities,the authors present a new sequential testing procedure,based on the locally smoothed adjacency matrix and the extreme value theory.Under the null hypothesis,the test statistic converges to the type I extreme value distribution,and otherwise,it explodes fast and the divergence rate could even reach n in the strong signal case where n is the size of the network,guaranteeing high detection power.This method is simple to use and serves as an alternative approach to the novel one in Lei(2016)using random matrix theory.To detect the change of the community structure,the authors also propose a two-sample test for the stochastic block model with two observed adjacency matrices.Simulation studies justify the theory.The authors apply the proposed method to the political blog data set and find reasonable group structures.展开更多
Online social networks have attracted great attention recently, because they make it easy to build social connections for people all over the world. However, the observed structure of an online social network is alway...Online social networks have attracted great attention recently, because they make it easy to build social connections for people all over the world. However, the observed structure of an online social network is always the aggregation of multiple social relationships. Thus, it is of great importance for real-world networks to reconstruct the full network structure using limited observations. The multiplex stochastic block model is introduced to describe multiple social ties, where different layers correspond to different attributes(e.g., age and gender of users in a social network). In this letter, we aim to improve the model precision using maximum likelihood estimation, where the precision is defined by the cross entropy of parameters between the data and model. Within this framework, the layers and partitions of nodes in a multiplex network are determined by natural node annotations, and the aggregate of the multiplex network is available. Because the original multiplex network has a high degree of freedom, we add an independent functional layer to cover it, and theoretically provide the optimal block number of the added layer.Empirical results verify the effectiveness of the proposed method using four measures, i.e., error of link probability,cross entropy, area under the receiver operating characteristic curve, and Bayes factor.展开更多
A multi-block model and a corresponding computer program have been developed which predict the kinematics of landslides.Furthermore,a unique event for studying different models simulating the triggering and movement o...A multi-block model and a corresponding computer program have been developed which predict the kinematics of landslides.Furthermore,a unique event for studying different models simulating the triggering and movement of landslides is the 2008Wenchuan earthquake in the mountainous region in Sichuan Province of China,which caused a large number of rapid landslides.The purpose of the paper is two-fold:(a)to propose and incorporate into the multi-block model constitutive relations predicting soil response along slip surfaces,and(b)to apply the multi-block model with the constitutive relations at landslides triggered by the Wenchuan earthquake.The proposed constitutive equations predict the shape of the shear stress-displacement response measured in ring shear tests.In the application,four landslides caused by the Wenchuan earthquake were considered.Only in one of these landslides the shear resistance-displacement response along the slip surface has been measured in laboratory tests.At this landslide,the triggering and movement of the landslide was predicted.In the other landslides,back analyses were performed and it was observed that the multi-block model predicted reasonably well the final configuration of all slides.In addition,as the measured and back-estimated total friction angle of all landslides was less than 180,and the materials along the slip surface were sandy,it is inferred that some,or all of the slip surface during these slides was sheared in an undrained manner and excess pore pressures generated during sliding played a key role in the triggering and movement of these landslides.Concluding,the paper(A)proposed and validated a multi-block constitutive model which can be applied to predict the triggering and movement of earthquake-induced slides and(B)by analyzing four landslides of the 2008 Wenchuan earthquake,it concludes that some,or all of the slip surface during these slides,was sheared in an undrained manner and excess pore pressures generated during sliding played a key role in the triggering and movement of these landslides.展开更多
The model of rigid and elastic-plastic motion and strain in intraplate blocks is established in the paper. The unique of strain parameters and minimum root-mean-square error of velocity residual of blocks are tested i...The model of rigid and elastic-plastic motion and strain in intraplate blocks is established in the paper. The unique of strain parameters and minimum root-mean-square error of velocity residual of blocks are tested in the model. Based on the velocity fields in Chinese mainland and its peripheral areas, the strain parameters of 8 blocks are estimated and their strain status analyzed. The estimated strain status of each block is well consistent with those derived by the methods of geology and geophysics. The principal direction of collision force from India plate to Eurasia plate estimated from the azimuth of principal compressive strain of Himalaya block might be N7.1°E.展开更多
In the paper, the kinematic model of tectonic blocks in southwest China is studied based on the precision GPS observations carried out under the major subject of 'Studies on Current Crustal Movement and Geodynamic...In the paper, the kinematic model of tectonic blocks in southwest China is studied based on the precision GPS observations carried out under the major subject of 'Studies on Current Crustal Movement and Geodynamics' which belongs to the State Climbing Project. It is believed that at present, the data of high precision GPS observation may provide convincing information related to the horizontal movement of tectonic blocks in the Chinese mainland. The preliminary results obtained from the kinematic model have given some direct evidences for the research of dynamic mechanism of crustal deformation in the Chinese mainland and on the basis of which, the kinematic characteristics and their relations to the seismicity and seismic risk in the reobserved region are analysed. The preliminary observation results are encouraging.展开更多
A pore network model was used in this paper to investigate the factors, in particular, throat radius, wettability and initial water saturation, causing water block in low permeability reservoirs. A new term - ＇relati...A pore network model was used in this paper to investigate the factors, in particular, throat radius, wettability and initial water saturation, causing water block in low permeability reservoirs. A new term - ＇relative permeability number＇ （RPN） was firstly defined, and then used to describe the degree of water block. Imbibition process simulations show that the RPN drops in accordance with the extension of the averaged pore throat radius from 0.05 to 1.5 μm, and yet once beyond that point of 1.5 μm, the RPN reaches a higher value, indicating the existence of a critical pore throat radius where water block is the maximum. When the wettability of the samples changes from water-wet to weakly water-wet, weakly gas-wet, or gas（oil）-wet, the gas RPN increases consistently, but this consistency is disturbed by the RPN dropping for weakly water-wet samples for water saturations less than 0.4, which means weakly waterwet media are more easily water blocked than water-wet systems. In the situation where the initial water saturation exceeds 0.05, water block escalates along with an increase in initial water saturation.展开更多
This paper mainly deals with the simulation on the strength of the concrete armor block in model test. According to the requirement for the strength of blocks in models with various scales, the components of materials...This paper mainly deals with the simulation on the strength of the concrete armor block in model test. According to the requirement for the strength of blocks in models with various scales, the components of materials for model blocks and their proportions are determined. The failure of armor blocks on rubble-mound breakwaters is reproduced by model tests.展开更多
The North China block,the western portion of the Sino- Korean Craton,is rounded byYanshanian in the north and Qinling- Dabie orogenic belts in the south.The widespread de-velopment of extensional basins in thisblock i...The North China block,the western portion of the Sino- Korean Craton,is rounded byYanshanian in the north and Qinling- Dabie orogenic belts in the south.The widespread de-velopment of extensional basins in thisblock indicates horizontal extension or continued thin-ning of a previousely thickened,unstable lithosphere throughout the Mesozoic.In this pa-per,we attempt to simulate numerically the geodynamical process of the basin formation byusing the mountain- basin evolution system.We assume thatthe formation of numeroussedi-mentary basins in the North China block is the resultofthe crustal extension,which destruc-ts rapidly the previously thickened crust.The gravitational collapse of the thickened crust ispossibly triggered by the re- orientation of the far- field stress regime,or the relaxation of theboundary resistantstress.展开更多
In this paper, we developed a new continuous block method by the method of interpolation and collocation to derive new scheme. We adopted the use of power series as a basis function for approximate solution. We evalua...In this paper, we developed a new continuous block method by the method of interpolation and collocation to derive new scheme. We adopted the use of power series as a basis function for approximate solution. We evaluated at off grid points to get a continuous hybrid multistep method. The continuous hybrid multistep method is solved for the independent solution to yield a continuous block method which is evaluated at selected points to yield a discrete block method. The basic properties of the block method were investigated and found to be consistent, zero stable and convergent. The results were found to compete favorably with the existing methods in terms of accuracy and error bound. In particular, the scheme was found to have a large region of absolute stability. The new method was tested on real life problem namely: Dynamic model.展开更多
The San Rafael Block(SRB)is part of one of the main retroarc volcanic provinces in southern Central Andes in Mendoza,Argentina.This block is located in the Andean foothills between the orogenic front and foreland base...The San Rafael Block(SRB)is part of one of the main retroarc volcanic provinces in southern Central Andes in Mendoza,Argentina.This block is located in the Andean foothills between the orogenic front and foreland basement uplifts of late Miocene age.In order to analyze the geochronological evolution of the Quaternary volcanism in the region,several geologic and geophysical studies have been conducted.Nevertheless,the crust,where the SRB is located,has not been well characterized yet.Based on gravimetric and magnetic data,together with isostatic and elastic thickness analyses,we modeled the crustal structure of the area.Information obtained has allowed us to understand the crust where the SRB and the Payenia volcanic province are located.Bouguer anomalies indicate that the SRB presents higher densities to the North of Cerro Nevado and Moho calculations suggest depths for this block between 40 and 50 km.Determinations of elastic thickness would indicate that the crust supporting the San Rafael Block presents values of approximately 10 km,being enough to support the block loading.However,in the Payenia region,elastic thickness values are close to zero due to the regional temperature increase.展开更多
Three-dimensional geological modeling of reservoirs is an essential tool to predict reservoir performance and improve the understanding of reservoir uniqueness in Es1 formation. The paper focuses on the use of petrel ...Three-dimensional geological modeling of reservoirs is an essential tool to predict reservoir performance and improve the understanding of reservoir uniqueness in Es1 formation. The paper focuses on the use of petrel software to build three-dimensional reservoir geological model which characterizes and assesses block Nv32 that located in the west of the Shenvsi oilfield in the south of Cangzhou city, Hebei province of China, and has an oil-bearing area of 1.4 km<sup>2</sup>. This study is depending on integration data from well logs of 22 wells which provided from geology, geophysics, and petrophysics to identify and provide precise depict of the subsurface internal structure and the reservoir heterogeneity. Input data was used to build the structural model, sedimentary facies model, petrophysical properties (porosity, permeability, saturation, and N/G model, and finally to determine the reservoir volume. The lithological facies were simulated using the assigned value method. Moreover, Petrophysical properties (Porosity, permeability, oil saturation and net to gross) were constructed for each zone using the Sequential Gaussian Simulation method to guide the distribution of petrophysical properties of Es1 formation, block Nv32. Statistical analysis of the porosity, permeability, oil saturation and N/G model present that the porosity occurrence distribution is mainly concern between 0.2% - 36.39% of block Nv32 with an average porosity value of 17.5%, permeability between 0.017 mD to 974.8 mD, having an average permeability of 59.44 mD, oil saturation between 0.00 to 0.95 having an average value of 0.22, and N/G is mainly concentrated between 0.01 to 1.00 within an average value of 0.61. This research has indicated the reliability of the three-dimensional model technique as a suitable tool to provide a sufficient understanding of petrophysical distribution. The south-western and north-western indicate that oilfield is very promising an exploratory well should be drilled to find out the thickness and size of the reservoir.展开更多
The Qinghai Nanshan fault is a larger fault in the Northeastern Xizang Plateau.In previous studies,its movement characteristics are mainly investigated with geological and seismic observations,and the tectonic transfo...The Qinghai Nanshan fault is a larger fault in the Northeastern Xizang Plateau.In previous studies,its movement characteristics are mainly investigated with geological and seismic observations,and the tectonic transformation role of the fault on its east is not yet clear.This study uses data fusion to obtain denser GPS observations near the Qinghai Nanshan fault.Based on tectonic characteristics,we establish a block model to investigate the fault slip rate,locking degree,and slip deficit.The results show that the Qinghai Nanshan fault slip rate is characterized by sinistral and convergent movement.Both the sinistral and convergent rates display a decreasing trend from west to east.The locking degree and slip deficit are higher in the western segment(with an average of about 0.74 and 1.1 mm/a)and lower in the eastern segment.Then,we construct a strain rate field using GPS observations to analyze the regional strain characteristics.The results indicate that along the fault,the western segment shows a larger shear strain rate and negative dilation rate.Regional earthquake records show that the frequency of earthquakes is lower near the fault.The joint results suggest that the western segment may have a higher earthquake risk.In addition,the insignificant fault slip rate in the eastern segment may indicate that it does not participate in the tectonic transformation among the Riyueshan,Lajishan,and West Qinling faults.展开更多
基金Projects(41572317,51374242)supported by the National Natural Science Foundation of ChinaProject(2015CX005)supported by the Innovation Driven Plan of Central South University,China
文摘Data organization requires high efficiency for large amount of data applied in the digital mine system. A new method of storing massive data of block model is proposed to meet the characteristics of the database, including ACID-compliant, concurrency support, data sharing, and efficient access. Each block model is organized by linear octree, stored in LMDB（lightning memory-mapped database）. Geological attribute can be queried at any point of 3D space by comparison algorithm of location code and conversion algorithm from address code of geometry space to location code of storage. The performance and robustness of querying geological attribute at 3D spatial region are enhanced greatly by the transformation from 3D to 2D and the method of 2D grid scanning to screen the inner and outer points. Experimental results showed that this method can access the massive data of block model, meeting the database characteristics. The method with LMDB is at least 3 times faster than that with etree, especially when it is used to read. In addition, the larger the amount of data is processed, the more efficient the method would be.
基金funded by Russian Foundation for Basic Research according to research project No.15-55-53104National Natural Science Foundation of China according to International cooperation project No.41511130032
文摘Recently published results of field and laboratory experiments on the seismic/acoustic response to injection of direct current （DC） pulses into the Earth crust or stressed rock samples raised a question on a possibility of electrical earthquake triggering. A physical mechanism of the considered phenomenon is not clear yet in view of the very low current density （10-7-10-s A/m^2） generated by the pulsed power systems at the epicenter depth （5-10 km） of local earthquakes occurred just after the current injection. The paper describes results of laboratory ＂earthquake＂ triggering by DC pulses under conditions of a spring-block model simulated the seismogenic fault. It is experimentally shown that the electric triggering of the laboratory ＂earthquake＂ （sharp slip of a movable block of the spring-block system） is possible only within a range of subcritical state of the system, when the shear stress between the movable and fixed blocks obtains 0.98-0.99 of its critical value. The threshold of electric triggering action is about 20 A/m^2 that is 7-8 orders of magnitude higher than estimated electric current density for Bishkek test site （Northern Tien Shan, Kirghizia） where the seismic response to the man-made electric action was observed. In this connection, the electric triggering phenomena may be explained by contraction of electric current in the narrow conductive areas of the faults and the corresponding increase in current density or by involving the secondary triggering mechanisms like electromagnetic stimulation of conductive fluid migration into the fault area resulted in decrease in the fault strength properties.
基金the management of Sierra Rutile Company for providing the drillhole dataset used in this studythe Japanese Ministry of Education Science and Technology (MEXT) Scholarship for academic funding
文摘In this research, a method called ANNMG is presented to integrate Artificial Neural Networks and Geostatistics for optimum mineral reserve evaluation. The word ANNMG simply means Artificial Neural Network Model integrated with Geostatiscs, In this procedure, the Artificial Neural Network was trained, tested and validated using assay values obtained from exploratory drillholes. Next, the validated model was used to generalize mineral grades at known and unknown sampled locations inside the drilling region respectively. Finally, the reproduced and generalized assay values were combined and fed to geostatistics in order to develop a geological 3D block model. The regression analysis revealed that the predicted sample grades were in close proximity to the actual sample grades, The generalized grades from the ANNMG show that this process could be used to complement exploration activities thereby reducing drilling requirement. It could also be an effective mineral reserve evaluation method that could oroduce optimum block model for mine design.
基金The research conducted for this study was funded by the National Institute for Occupational Safety and Health(NIOSH)under Grant No.200-2016-90154.
文摘Bonded blockmodel(BBM)has shownpotential in replicating rockmass behavior aswell as the rockesupport interactionmechanism,but their practical application is limited totwo dimensions due to the high associated computational demand.To allow for the use of BBM in simulating three-dimensional(3D)problems,this study proposes an integrated 3D continuumetwo-dimensional(2D)discontinuum approach,in context of rock pillars.A cross-section of a granite pillar was simulated using a BBM with a load path from a calibrated mine-scale FLAC^(3D)model.Pillar support as employed in the mine was also incorporated in different stages during the simulation.Themodel was calibrated by varying the input parameters until the displacements at six locations within the pillarmatchedthosemeasuredby amulti-point borehole extensometer(MPBX)inthe field.The calibratedmodel was subsequently used to understand how the support and load path influenced the damage evolution in the pillar.The shear component of the load pathwas found to have amajor effect on the severity and extent of the damaged regions.When the support density was increased in the model,the lateral displacements along the pillar walls were significantly suppressed in a somewhat unpredictable manner.Thiswas explained by the interaction between the supports and the damaged regions at the corners,which ultimately modified the stresses along the pillar periphery.The amount of displacement reduction obtained by increasing the support density illustrates the potential of BBMto be used as a support design tool.
文摘The solid block model is applied to describe the motion of the pyroclastic flow under the joint action of gravity and Coulomb friction. Special attention is paid to characteristics of the pyroclastic flow generated by Montserrat volcano in likely directions. The critical friction angle of the flow propagation is evaluated empirically. Characteristic parameters of the pyroclastic flow (travel time and impact velocity) are well approximated by linear regressions. Proposed estimations of the parameters of pyroclastic flow are useful for the rough and express evaluation of its characteristics.
文摘Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid environments are not mastered. This article evaluates the influence of architectural and constructive modes of buildings made of CEB walls and concrete block walls, to optimize and compare their thermal comfort in the hot and dry tropical climate of Ouagadougou, Burkina Faso. Two identical pilot buildings whose envelopes are made of CEB and concrete blocks were monitored for this study. The thermal models of the pilot buildings were implemented in the SketchUp software using an extension of EnergyPlus. The models were empirically validated after calibration against measured thermal data from the buildings. The models were used to do a parametric analysis for optimization of the thermal performances by simulating plaster coatings on the exterior of walls, airtight openings and natural ventilation depending on external weather conditions. The results show that the CEB building displays 7016 hours of discomfort, equivalent to 80.1% of the time, and the concrete building displays 6948 hours of discomfort, equivalent to 79.3% of the time. The optimization by modifications reduced the discomfort to 2918 and 3125 hours respectively;i.e. equivalent to only 33.3% for the CEB building and 35.7% for the concrete building. More study should evaluate thermal optimizations in buildings in real time of usage such as residential buildings commonly used by the local middle class. The use of CEB as a construction material and passive means of improving thermal comfort is a suitable ecological and economical option to replace cementitious material.
基金supported by the National Natural Science Foundation of China under Grant No.71971118supported by Major Natural Science Projects of Universities in Jiangsu Province under Grant No.20KJA520002。
文摘In this paper,to obtain a consistent estimator of the number of communities,the authors present a new sequential testing procedure,based on the locally smoothed adjacency matrix and the extreme value theory.Under the null hypothesis,the test statistic converges to the type I extreme value distribution,and otherwise,it explodes fast and the divergence rate could even reach n in the strong signal case where n is the size of the network,guaranteeing high detection power.This method is simple to use and serves as an alternative approach to the novel one in Lei(2016)using random matrix theory.To detect the change of the community structure,the authors also propose a two-sample test for the stochastic block model with two observed adjacency matrices.Simulation studies justify the theory.The authors apply the proposed method to the political blog data set and find reasonable group structures.
基金Project supported by the National Natural Science Foundation of China (No. 61731004)。
文摘Online social networks have attracted great attention recently, because they make it easy to build social connections for people all over the world. However, the observed structure of an online social network is always the aggregation of multiple social relationships. Thus, it is of great importance for real-world networks to reconstruct the full network structure using limited observations. The multiplex stochastic block model is introduced to describe multiple social ties, where different layers correspond to different attributes(e.g., age and gender of users in a social network). In this letter, we aim to improve the model precision using maximum likelihood estimation, where the precision is defined by the cross entropy of parameters between the data and model. Within this framework, the layers and partitions of nodes in a multiplex network are determined by natural node annotations, and the aggregate of the multiplex network is available. Because the original multiplex network has a high degree of freedom, we add an independent functional layer to cover it, and theoretically provide the optimal block number of the added layer.Empirical results verify the effectiveness of the proposed method using four measures, i.e., error of link probability,cross entropy, area under the receiver operating characteristic curve, and Bayes factor.
基金The National Key R＆D Program of China (2017YFC1502903) Sichuan International Cooperation and Exchange for Science and Technology (2016HH0079)+1 种基金 ＂Novel methodologies for the assessment of risk of ground displacement＂ under ESPA 2007-2013 of Greece under
文摘A multi-block model and a corresponding computer program have been developed which predict the kinematics of landslides.Furthermore,a unique event for studying different models simulating the triggering and movement of landslides is the 2008Wenchuan earthquake in the mountainous region in Sichuan Province of China,which caused a large number of rapid landslides.The purpose of the paper is two-fold:(a)to propose and incorporate into the multi-block model constitutive relations predicting soil response along slip surfaces,and(b)to apply the multi-block model with the constitutive relations at landslides triggered by the Wenchuan earthquake.The proposed constitutive equations predict the shape of the shear stress-displacement response measured in ring shear tests.In the application,four landslides caused by the Wenchuan earthquake were considered.Only in one of these landslides the shear resistance-displacement response along the slip surface has been measured in laboratory tests.At this landslide,the triggering and movement of the landslide was predicted.In the other landslides,back analyses were performed and it was observed that the multi-block model predicted reasonably well the final configuration of all slides.In addition,as the measured and back-estimated total friction angle of all landslides was less than 180,and the materials along the slip surface were sandy,it is inferred that some,or all of the slip surface during these slides was sheared in an undrained manner and excess pore pressures generated during sliding played a key role in the triggering and movement of these landslides.Concluding,the paper(A)proposed and validated a multi-block constitutive model which can be applied to predict the triggering and movement of earthquake-induced slides and(B)by analyzing four landslides of the 2008 Wenchuan earthquake,it concludes that some,or all of the slip surface during these slides,was sheared in an undrained manner and excess pore pressures generated during sliding played a key role in the triggering and movement of these landslides.
基金State Key Basic Development and Program Project (G19980407).
文摘The model of rigid and elastic-plastic motion and strain in intraplate blocks is established in the paper. The unique of strain parameters and minimum root-mean-square error of velocity residual of blocks are tested in the model. Based on the velocity fields in Chinese mainland and its peripheral areas, the strain parameters of 8 blocks are estimated and their strain status analyzed. The estimated strain status of each block is well consistent with those derived by the methods of geology and geophysics. The principal direction of collision force from India plate to Eurasia plate estimated from the azimuth of principal compressive strain of Himalaya block might be N7.1°E.
文摘In the paper, the kinematic model of tectonic blocks in southwest China is studied based on the precision GPS observations carried out under the major subject of 'Studies on Current Crustal Movement and Geodynamics' which belongs to the State Climbing Project. It is believed that at present, the data of high precision GPS observation may provide convincing information related to the horizontal movement of tectonic blocks in the Chinese mainland. The preliminary results obtained from the kinematic model have given some direct evidences for the research of dynamic mechanism of crustal deformation in the Chinese mainland and on the basis of which, the kinematic characteristics and their relations to the seismicity and seismic risk in the reobserved region are analysed. The preliminary observation results are encouraging.
基金support from the National Key Technology R&D Program in the 11th Five-Year Plan Period (Grant No: 2008ZX05054)the Non-main Petroleum Subject Cultivating Fund of China University of Petroleum.
文摘A pore network model was used in this paper to investigate the factors, in particular, throat radius, wettability and initial water saturation, causing water block in low permeability reservoirs. A new term - ＇relative permeability number＇ （RPN） was firstly defined, and then used to describe the degree of water block. Imbibition process simulations show that the RPN drops in accordance with the extension of the averaged pore throat radius from 0.05 to 1.5 μm, and yet once beyond that point of 1.5 μm, the RPN reaches a higher value, indicating the existence of a critical pore throat radius where water block is the maximum. When the wettability of the samples changes from water-wet to weakly water-wet, weakly gas-wet, or gas（oil）-wet, the gas RPN increases consistently, but this consistency is disturbed by the RPN dropping for weakly water-wet samples for water saturations less than 0.4, which means weakly waterwet media are more easily water blocked than water-wet systems. In the situation where the initial water saturation exceeds 0.05, water block escalates along with an increase in initial water saturation.
文摘This paper mainly deals with the simulation on the strength of the concrete armor block in model test. According to the requirement for the strength of blocks in models with various scales, the components of materials for model blocks and their proportions are determined. The failure of armor blocks on rubble-mound breakwaters is reproduced by model tests.
文摘The North China block,the western portion of the Sino- Korean Craton,is rounded byYanshanian in the north and Qinling- Dabie orogenic belts in the south.The widespread de-velopment of extensional basins in thisblock indicates horizontal extension or continued thin-ning of a previousely thickened,unstable lithosphere throughout the Mesozoic.In this pa-per,we attempt to simulate numerically the geodynamical process of the basin formation byusing the mountain- basin evolution system.We assume thatthe formation of numeroussedi-mentary basins in the North China block is the resultofthe crustal extension,which destruc-ts rapidly the previously thickened crust.The gravitational collapse of the thickened crust ispossibly triggered by the re- orientation of the far- field stress regime,or the relaxation of theboundary resistantstress.
文摘In this paper, we developed a new continuous block method by the method of interpolation and collocation to derive new scheme. We adopted the use of power series as a basis function for approximate solution. We evaluated at off grid points to get a continuous hybrid multistep method. The continuous hybrid multistep method is solved for the independent solution to yield a continuous block method which is evaluated at selected points to yield a discrete block method. The basic properties of the block method were investigated and found to be consistent, zero stable and convergent. The results were found to compete favorably with the existing methods in terms of accuracy and error bound. In particular, the scheme was found to have a large region of absolute stability. The new method was tested on real life problem namely: Dynamic model.
文摘The San Rafael Block(SRB)is part of one of the main retroarc volcanic provinces in southern Central Andes in Mendoza,Argentina.This block is located in the Andean foothills between the orogenic front and foreland basement uplifts of late Miocene age.In order to analyze the geochronological evolution of the Quaternary volcanism in the region,several geologic and geophysical studies have been conducted.Nevertheless,the crust,where the SRB is located,has not been well characterized yet.Based on gravimetric and magnetic data,together with isostatic and elastic thickness analyses,we modeled the crustal structure of the area.Information obtained has allowed us to understand the crust where the SRB and the Payenia volcanic province are located.Bouguer anomalies indicate that the SRB presents higher densities to the North of Cerro Nevado and Moho calculations suggest depths for this block between 40 and 50 km.Determinations of elastic thickness would indicate that the crust supporting the San Rafael Block presents values of approximately 10 km,being enough to support the block loading.However,in the Payenia region,elastic thickness values are close to zero due to the regional temperature increase.
文摘Three-dimensional geological modeling of reservoirs is an essential tool to predict reservoir performance and improve the understanding of reservoir uniqueness in Es1 formation. The paper focuses on the use of petrel software to build three-dimensional reservoir geological model which characterizes and assesses block Nv32 that located in the west of the Shenvsi oilfield in the south of Cangzhou city, Hebei province of China, and has an oil-bearing area of 1.4 km<sup>2</sup>. This study is depending on integration data from well logs of 22 wells which provided from geology, geophysics, and petrophysics to identify and provide precise depict of the subsurface internal structure and the reservoir heterogeneity. Input data was used to build the structural model, sedimentary facies model, petrophysical properties (porosity, permeability, saturation, and N/G model, and finally to determine the reservoir volume. The lithological facies were simulated using the assigned value method. Moreover, Petrophysical properties (Porosity, permeability, oil saturation and net to gross) were constructed for each zone using the Sequential Gaussian Simulation method to guide the distribution of petrophysical properties of Es1 formation, block Nv32. Statistical analysis of the porosity, permeability, oil saturation and N/G model present that the porosity occurrence distribution is mainly concern between 0.2% - 36.39% of block Nv32 with an average porosity value of 17.5%, permeability between 0.017 mD to 974.8 mD, having an average permeability of 59.44 mD, oil saturation between 0.00 to 0.95 having an average value of 0.22, and N/G is mainly concentrated between 0.01 to 1.00 within an average value of 0.61. This research has indicated the reliability of the three-dimensional model technique as a suitable tool to provide a sufficient understanding of petrophysical distribution. The south-western and north-western indicate that oilfield is very promising an exploratory well should be drilled to find out the thickness and size of the reservoir.
基金supported by the National Natural Science Foundation of China(41874011,42074007)the Fundamental Research Funds for the Central Universities(2042023kfyq01)。
文摘The Qinghai Nanshan fault is a larger fault in the Northeastern Xizang Plateau.In previous studies,its movement characteristics are mainly investigated with geological and seismic observations,and the tectonic transformation role of the fault on its east is not yet clear.This study uses data fusion to obtain denser GPS observations near the Qinghai Nanshan fault.Based on tectonic characteristics,we establish a block model to investigate the fault slip rate,locking degree,and slip deficit.The results show that the Qinghai Nanshan fault slip rate is characterized by sinistral and convergent movement.Both the sinistral and convergent rates display a decreasing trend from west to east.The locking degree and slip deficit are higher in the western segment(with an average of about 0.74 and 1.1 mm/a)and lower in the eastern segment.Then,we construct a strain rate field using GPS observations to analyze the regional strain characteristics.The results indicate that along the fault,the western segment shows a larger shear strain rate and negative dilation rate.Regional earthquake records show that the frequency of earthquakes is lower near the fault.The joint results suggest that the western segment may have a higher earthquake risk.In addition,the insignificant fault slip rate in the eastern segment may indicate that it does not participate in the tectonic transformation among the Riyueshan,Lajishan,and West Qinling faults.
