In this paper, a special-purpose CAD/CAM software package, BliskCad/Cam, based on a commercial CAD/CAM software Unigraphics is developed to reduce difficulties in CNC-EDM of the shrouded turbine blisks. The software p...In this paper, a special-purpose CAD/CAM software package, BliskCad/Cam, based on a commercial CAD/CAM software Unigraphics is developed to reduce difficulties in CNC-EDM of the shrouded turbine blisks. The software package consists of five modules such as electrode design, path searching, and machining simulation module. Functions of BliskCad/Cam include parametrical reconstruction of 3-D model of the blisk, intelligent design of complex shaped electrode, automatic generation of NC codes, search of interference-free tool path for multi-axis NC-EDM and machining simulation, etc. Experimental verification is conducted by using BliskCad/Cam and the results show that it satisfies the requirements, and can realize precision machining and reduce accessorial time remarkably.展开更多
Powder Mixed Electric Discharge Machining (PMEDM) has different mechanism from conventional EDM, which can improve the surface roughness and surface quality distinctly and to obtain nearly mirror surface effects. It i...Powder Mixed Electric Discharge Machining (PMEDM) has different mechanism from conventional EDM, which can improve the surface roughness and surface quality distinctly and to obtain nearly mirror surface effects. It is a useful finish machining method and is researched and applied by many countries. However there are little research on rough machining of PMEDM. Experiments show that PMEDM machining makes discharge breakdown easier, enlarges the discharge gaps and widens discharge passage, and at last forms even distributed and "large and shadow" shaped etched cavities. Because of much loss of discharge energy in the discharge gaps and reduction of ejecting force on the melted material, the machining efficiency gets lower and the surface roughness gets small in PMEDM machining in comparison with conventional EDM machining. This paper performs experimental research on the machining efficiency and surface roughness of PMEDM in rough machining. The machining efficiency of PMEDM can be highly increased by selecting proper discharge parameters (increasing peak current, reducing pulse width) with approximate surface roughness in comparison with conventional EDM machining. Although PMEDM can improve machining efficiency in rough efficiency, but a series of problems like electrode wear, efficiently separation of machined scraps from the powder mixed working fluid, should be solved before PMEDM machining is really applied in rough machining. Experiments result shows that powder mixed EDM machining can obviously improve machining efficiency at the same surface roughness by selecting proper discharging parameters, and can provide reference accordingly for the application of PMEDM machining technology in rough machining.展开更多
A new method of electrical discharge machining （EDM） in air-mixed medium--air-mixed EDM was presented, and comparative experiments were carried out to compare the machining characteristics of air-mixed EDM with conv...A new method of electrical discharge machining （EDM） in air-mixed medium--air-mixed EDM was presented, and comparative experiments were carried out to compare the machining characteristics of air-mixed EDM with conventional EDM. The experimental results showed that better machining performances were obtained with tool electrode as the cathode and workpieee as the anode. It was found that the material removal rate （MRR） was higher, the tool electrode relative wear ratio （TWR） was lower and the surface roughness （SR） quality was better in the case of air-mixed EDM than that of conventional EDM, and the reasons bringing out the results were analyzed.展开更多
Shape memory alloys （SMAs） are the developing advanced materials due to their versatile specific properties such as pseudoelasticity, shape memory effect （SME）, biocompatibility, high specific strength, high corro...Shape memory alloys （SMAs） are the developing advanced materials due to their versatile specific properties such as pseudoelasticity, shape memory effect （SME）, biocompatibility, high specific strength, high corrosion resistance, high wear resistance and high anti-fatigue property. Therefore, the SMAs are used in many applications such as aerospace, medical and automobile. However, the conventional machining of SMAs causes serious tool wear, time consuming and less dimensional deformity due to severe strain hardening and pseudoelasticity. These materials can be machined using non-conventional methods such as laser machining, water jet machining （WJM） and electrochemical machining （ECM）, but these processes are limited to complexity and mechanical properties of the component. Electrical discharge machining （EDM） and wire EDM （WEDM） show high capability to machine SMAs of complex shapes with precise dimensions. The aim of this work is to present the consolidated references on the machining of SMAs using EDM and WEDM and subsequently identify the research gaps. In support to these research gaps, this work has also evolved the future research directions.展开更多
Servo scanning 3D micro electrical discharge machining (3D SSMEDM) is a novel and effective method in fabricating complex 3D micro structures with high aspect ratio on conducting materials. In 3D SSMEDM process, the a...Servo scanning 3D micro electrical discharge machining (3D SSMEDM) is a novel and effective method in fabricating complex 3D micro structures with high aspect ratio on conducting materials. In 3D SSMEDM process, the axial wear of tool electrode can be compensated automatically by servo-keeping discharge gap, instead of the traditional methods that depend on experiential models or intermittent compensation. However, the effects of process parameters on 3D SSMEDM have not been reported up until now. In this study, the emphasis is laid on the effects of pulse duration, peak current, machining polarity, track style, track overlap, and scanning velocity on the 3D SSMEDM performances of machining efficiency, processing status, and surface accuracy. A series of experiments were carried out by machining a micro-rectangle cavity (900 μm×600 μm) on doped silicon. The experimental results were obtained as follows. Peak current plays a main role in machining efficiency and surface accuracy. Pulse duration affects obviously the stability of discharge state. The material removal rate of cathode processing is about 3/5 of that of anode processing. Compared with direction-parallel path, contour-parallel path is better in counteracting the lateral wear of tool electrode end. Scanning velocity should be selected moderately to avoid electric arc and short. Track overlap should be slightly less than the radius of tool electrode. In addition, a typical 3D micro structure of eye shape was machined based on the optimized process parameters. These results are beneficial to improve machining stability, accuracy, and efficiency in 3D SSMEDM.展开更多
This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface wi...This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.展开更多
To develop a hybrid process of abrasive jet machining (AJM) and electrical discharge machining (EDM),the effects of the hybrid process parameters on machining performance were comprehensively investigated to confirm t...To develop a hybrid process of abrasive jet machining (AJM) and electrical discharge machining (EDM),the effects of the hybrid process parameters on machining performance were comprehensively investigated to confirm the benefits of this hybrid process.The appropriate abrasives delivered by high speed gas media were incorporated with an EDM in gas system to construct the hybrid process of AJM and EDM,and then the high speed abrasives could impinge on the machined surface to remove the recast layer caused by EDM process to increase the efficiency of material removal and reduce the surface roughness.In this study,the benefits of the hybrid process were determined as the machining performance of hybrid process was compared with that of the EDM in gas system.The main process parameters were varied to explore their effects on material removal rate,surface roughness and surface integrities.The experimental results show that the hybrid process of AJM and EDM can enhance the machining efficiency and improve the surface quality.Consequently,the developed hybrid process can fit the requirements of modern manufacturing applications.展开更多
Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and...Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and time consuming. In this paper, artificial neural network (ANN) and genetic algorithm (GA) are used together to establish the parameter optimization model. An ANN model which adapts Levenberg-Marquardt algorithm has been set up to represent the relationship between material removal rate (MRR) and input parameters, and GA is used to optimize parameters, so that optimization results are obtained. The model is shown to be effective, and MRR is improved using optimized machining parameters.展开更多
Electrical discharge machining（EDM） is a promising non-traditional micro machining technology that offers a vast array of applications in the manufacturing industry. However, scale effects occur when machining at th...Electrical discharge machining（EDM） is a promising non-traditional micro machining technology that offers a vast array of applications in the manufacturing industry. However, scale effects occur when machining at the micro-scale, which can make it difficult to predict and optimize the machining performances of micro EDM. A new concept of ＂scale effects＂ in micro EDM is proposed, the scale effects can reveal the difference in machining performances between micro EDM and conventional macro EDM. Similarity theory is presented to evaluate the scale effects in micro EDM. Single factor experiments are conducted and the experimental results are analyzed by discussing the similarity difference and similarity precision. The results show that the output results of scale effects in micro EDM do not change linearly with discharge parameters. The values of similarity precision of machining time significantly increase when scaling-down the capacitance or open-circuit voltage. It is indicated that the lower the scale of the discharge parameter, the greater the deviation of non-geometrical similarity degree over geometrical similarity degree, which means that the micro EDM system with lower discharge energy experiences more scale effects. The largest similarity difference is 5.34 while the largest similarity precision can be as high as 114.03. It is suggested that the similarity precision is more effective in reflecting the scale effects and their fluctuation than similarity difference. Consequently, similarity theory is suitable for evaluating the scale effects in micro EDM. This proposed research offers engineering values for optimizing the machining parameters and improving the machining performances of micro EDM.展开更多
The wire electrical discharge machining（EDM） of 6061 aluminium alloy in terms of material removal rate,kerf/slit width,surface finish and wear of electrode wire for different pulse on time and wire tension was studi...The wire electrical discharge machining（EDM） of 6061 aluminium alloy in terms of material removal rate,kerf/slit width,surface finish and wear of electrode wire for different pulse on time and wire tension was studied.Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension.It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate.It seems that the higher wire tension facilitates steady machining process,which generates low wear in wire electrode and better surface finish.The surface roughness does not change notably with the variation of pulse on time.The appearance of the machined surfaces is very similar under all the machining conditions.The machined surface contains solidified molten material,splash of materials and blisters.The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input.The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side.The higher electrode wear introduces higher taper.展开更多
The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed...The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.展开更多
One of the reasons for increased material removal rate in magnetic field assisted dry electrical discharge machining （EDM） is confinement of plasma due to Lorentz forces. This paper presents a mathematical model to ...One of the reasons for increased material removal rate in magnetic field assisted dry electrical discharge machining （EDM） is confinement of plasma due to Lorentz forces. This paper presents a mathematical model to evaluate the effect of external magnetic field on crater depth and diameter in single- and multiple-discharge EDM process. The model incorporates three main effects of the magnetic field, which include plasma confinement, mean free path reduction and pulsating magnetic field effects. Upon the application of an external magnetic field, Lorentz forces that are developed across the plasma column confine the plasma column. Also, the magnetic field reduces the mean free path of electrons due to an increase in the plasma pressure and cycloidal path taken by the electrons between the electrodes. As the mean free path of electrons reduces, more ionization occurs in plasma column and eventually an increase in the current density at the inter-electrode gap occurs. The model results for crater depth and its diameter in single discharge dry EDM process show an error of 9%-10% over the respective experimental values.展开更多
An integrated CAD/CAPP/CAM system modeling for Electric Discharge Machining (EDM) is constructed on the basis of an integrated engineering database. EDM feature objects are developed using the object oriented database...An integrated CAD/CAPP/CAM system modeling for Electric Discharge Machining (EDM) is constructed on the basis of an integrated engineering database. EDM feature objects are developed using the object oriented database provided by AutoCAD R14, and EDM feature modeling is realized in AutoCAD environments.展开更多
This paper introduces a study on modelling surface finish in EDM （Electrical Discharge Machining） of tablet shape punches when using copper as electrode material. In this study, 27 experiments were performed based o...This paper introduces a study on modelling surface finish in EDM （Electrical Discharge Machining） of tablet shape punches when using copper as electrode material. In this study, 27 experiments were performed based on BBD （Box-Behnken Design） and the work-piece material was 9CrSi steel. The input process parameters were the current, the pulse on time, the pulse off time and the voltage. The effects of the input parameters on the surface finish were evaluated by analysing variance. Besides, from the results of the experiments, a regression equation for determining the surface roughness is introduced. Also, the optimum input parameter values were found in order to get the minimum surface roughness.展开更多
This machine toolis one of the new products developed and produced by the Shanghai No.8 Machine Tool Plant on the basis of advanced technologies introduced from at home and abroad. It has a wide machining travel and l...This machine toolis one of the new products developed and produced by the Shanghai No.8 Machine Tool Plant on the basis of advanced technologies introduced from at home and abroad. It has a wide machining travel and large volume of oil box, and adopts the stepping motor main spindle servo-controlled mechanism, which has the advantages of sensitive control, quick response speed, stable working state, simple structure,展开更多
The machining of small holes and array holes has been a difficult problem in machining field. Tiny hole is widely used in mechanical field, for instance, fuel injection nozzles, spinneret holes for synthetic fibers an...The machining of small holes and array holes has been a difficult problem in machining field. Tiny hole is widely used in mechanical field, for instance, fuel injection nozzles, spinneret holes for synthetic fibers and wire drawing dies. This paper investigated the application of EDM (electrical discharge machining) to the fabrication of micro structures. There are obvious limitations in the process of micro-electrical discharge machining, such as electrode wear, unstable discharge condition and low machining efficiency. The effects of EDM parameters were investigated, such as voltage, pulse frequency, and frequency of ultrasonic vibration applied to electrode. Micro holes were machined with Pt electrode made by focused-ion-beam chemical vapor deposition (FIB-CVD) and Cu electrode made by wire-electrode cutting. The comparison experiments between EDM and ECM (electrochemical machining) indicated that the processing of ECM has serious stray current corrosion and poor machining precision. Moreover, the workpiece vibration was firstly proposed to be utilized in the micro-electrical discharge machining. It can be concluded that maximum machine could be obtained under the amplitude ratio of 76%, which was an appropriate parameter.展开更多
文摘In this paper, a special-purpose CAD/CAM software package, BliskCad/Cam, based on a commercial CAD/CAM software Unigraphics is developed to reduce difficulties in CNC-EDM of the shrouded turbine blisks. The software package consists of five modules such as electrode design, path searching, and machining simulation module. Functions of BliskCad/Cam include parametrical reconstruction of 3-D model of the blisk, intelligent design of complex shaped electrode, automatic generation of NC codes, search of interference-free tool path for multi-axis NC-EDM and machining simulation, etc. Experimental verification is conducted by using BliskCad/Cam and the results show that it satisfies the requirements, and can realize precision machining and reduce accessorial time remarkably.
文摘Powder Mixed Electric Discharge Machining (PMEDM) has different mechanism from conventional EDM, which can improve the surface roughness and surface quality distinctly and to obtain nearly mirror surface effects. It is a useful finish machining method and is researched and applied by many countries. However there are little research on rough machining of PMEDM. Experiments show that PMEDM machining makes discharge breakdown easier, enlarges the discharge gaps and widens discharge passage, and at last forms even distributed and "large and shadow" shaped etched cavities. Because of much loss of discharge energy in the discharge gaps and reduction of ejecting force on the melted material, the machining efficiency gets lower and the surface roughness gets small in PMEDM machining in comparison with conventional EDM machining. This paper performs experimental research on the machining efficiency and surface roughness of PMEDM in rough machining. The machining efficiency of PMEDM can be highly increased by selecting proper discharge parameters (increasing peak current, reducing pulse width) with approximate surface roughness in comparison with conventional EDM machining. Although PMEDM can improve machining efficiency in rough efficiency, but a series of problems like electrode wear, efficiently separation of machined scraps from the powder mixed working fluid, should be solved before PMEDM machining is really applied in rough machining. Experiments result shows that powder mixed EDM machining can obviously improve machining efficiency at the same surface roughness by selecting proper discharging parameters, and can provide reference accordingly for the application of PMEDM machining technology in rough machining.
基金the Post-doctor Foundation of Heilongjiang Province(Grant No.LBH-Z06139).
文摘A new method of electrical discharge machining （EDM） in air-mixed medium--air-mixed EDM was presented, and comparative experiments were carried out to compare the machining characteristics of air-mixed EDM with conventional EDM. The experimental results showed that better machining performances were obtained with tool electrode as the cathode and workpieee as the anode. It was found that the material removal rate （MRR） was higher, the tool electrode relative wear ratio （TWR） was lower and the surface roughness （SR） quality was better in the case of air-mixed EDM than that of conventional EDM, and the reasons bringing out the results were analyzed.
文摘Shape memory alloys （SMAs） are the developing advanced materials due to their versatile specific properties such as pseudoelasticity, shape memory effect （SME）, biocompatibility, high specific strength, high corrosion resistance, high wear resistance and high anti-fatigue property. Therefore, the SMAs are used in many applications such as aerospace, medical and automobile. However, the conventional machining of SMAs causes serious tool wear, time consuming and less dimensional deformity due to severe strain hardening and pseudoelasticity. These materials can be machined using non-conventional methods such as laser machining, water jet machining （WJM） and electrochemical machining （ECM）, but these processes are limited to complexity and mechanical properties of the component. Electrical discharge machining （EDM） and wire EDM （WEDM） show high capability to machine SMAs of complex shapes with precise dimensions. The aim of this work is to present the consolidated references on the machining of SMAs using EDM and WEDM and subsequently identify the research gaps. In support to these research gaps, this work has also evolved the future research directions.
基金supported by National Natural Science Foundation of China (Grant No. 50905094)National Hi-tech Research and Development Program of China (863 Program, Grant No. 2009AA044204, Grant No. 2009AA044205)China Postdoctoral Science Foundation (Grant No. 20080440378, Grant No. 200902097)
文摘Servo scanning 3D micro electrical discharge machining (3D SSMEDM) is a novel and effective method in fabricating complex 3D micro structures with high aspect ratio on conducting materials. In 3D SSMEDM process, the axial wear of tool electrode can be compensated automatically by servo-keeping discharge gap, instead of the traditional methods that depend on experiential models or intermittent compensation. However, the effects of process parameters on 3D SSMEDM have not been reported up until now. In this study, the emphasis is laid on the effects of pulse duration, peak current, machining polarity, track style, track overlap, and scanning velocity on the 3D SSMEDM performances of machining efficiency, processing status, and surface accuracy. A series of experiments were carried out by machining a micro-rectangle cavity (900 μm×600 μm) on doped silicon. The experimental results were obtained as follows. Peak current plays a main role in machining efficiency and surface accuracy. Pulse duration affects obviously the stability of discharge state. The material removal rate of cathode processing is about 3/5 of that of anode processing. Compared with direction-parallel path, contour-parallel path is better in counteracting the lateral wear of tool electrode end. Scanning velocity should be selected moderately to avoid electric arc and short. Track overlap should be slightly less than the radius of tool electrode. In addition, a typical 3D micro structure of eye shape was machined based on the optimized process parameters. These results are beneficial to improve machining stability, accuracy, and efficiency in 3D SSMEDM.
文摘This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.
基金Project(NSC99-2212-E-252-006-MY3)Supported by National Science Council
文摘To develop a hybrid process of abrasive jet machining (AJM) and electrical discharge machining (EDM),the effects of the hybrid process parameters on machining performance were comprehensively investigated to confirm the benefits of this hybrid process.The appropriate abrasives delivered by high speed gas media were incorporated with an EDM in gas system to construct the hybrid process of AJM and EDM,and then the high speed abrasives could impinge on the machined surface to remove the recast layer caused by EDM process to increase the efficiency of material removal and reduce the surface roughness.In this study,the benefits of the hybrid process were determined as the machining performance of hybrid process was compared with that of the EDM in gas system.The main process parameters were varied to explore their effects on material removal rate,surface roughness and surface integrities.The experimental results show that the hybrid process of AJM and EDM can enhance the machining efficiency and improve the surface quality.Consequently,the developed hybrid process can fit the requirements of modern manufacturing applications.
基金Project supported by the National Natural Science Foundation of China (Nos. 50575128 and 50775128)the Outstanding Young Scientist Foundation of Shandong Province (No. 2005BS05004), China
文摘Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and time consuming. In this paper, artificial neural network (ANN) and genetic algorithm (GA) are used together to establish the parameter optimization model. An ANN model which adapts Levenberg-Marquardt algorithm has been set up to represent the relationship between material removal rate (MRR) and input parameters, and GA is used to optimize parameters, so that optimization results are obtained. The model is shown to be effective, and MRR is improved using optimized machining parameters.
基金Supported by National Natural Science Foundation of China(Grant No.51375274)China Postdoctoral Science Foundation(Grant No.2014M561920)
文摘Electrical discharge machining（EDM） is a promising non-traditional micro machining technology that offers a vast array of applications in the manufacturing industry. However, scale effects occur when machining at the micro-scale, which can make it difficult to predict and optimize the machining performances of micro EDM. A new concept of ＂scale effects＂ in micro EDM is proposed, the scale effects can reveal the difference in machining performances between micro EDM and conventional macro EDM. Similarity theory is presented to evaluate the scale effects in micro EDM. Single factor experiments are conducted and the experimental results are analyzed by discussing the similarity difference and similarity precision. The results show that the output results of scale effects in micro EDM do not change linearly with discharge parameters. The values of similarity precision of machining time significantly increase when scaling-down the capacitance or open-circuit voltage. It is indicated that the lower the scale of the discharge parameter, the greater the deviation of non-geometrical similarity degree over geometrical similarity degree, which means that the micro EDM system with lower discharge energy experiences more scale effects. The largest similarity difference is 5.34 while the largest similarity precision can be as high as 114.03. It is suggested that the similarity precision is more effective in reflecting the scale effects and their fluctuation than similarity difference. Consequently, similarity theory is suitable for evaluating the scale effects in micro EDM. This proposed research offers engineering values for optimizing the machining parameters and improving the machining performances of micro EDM.
文摘The wire electrical discharge machining（EDM） of 6061 aluminium alloy in terms of material removal rate,kerf/slit width,surface finish and wear of electrode wire for different pulse on time and wire tension was studied.Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension.It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate.It seems that the higher wire tension facilitates steady machining process,which generates low wear in wire electrode and better surface finish.The surface roughness does not change notably with the variation of pulse on time.The appearance of the machined surfaces is very similar under all the machining conditions.The machined surface contains solidified molten material,splash of materials and blisters.The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input.The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side.The higher electrode wear introduces higher taper.
基金Sponsored by the Fund for the Doctoral Program of Higher Education (RFDP) (Grant No. CBQQ24403007)the Innovation Fund of HIT(Grant No.CBQQ18400018)
文摘The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.
文摘One of the reasons for increased material removal rate in magnetic field assisted dry electrical discharge machining （EDM） is confinement of plasma due to Lorentz forces. This paper presents a mathematical model to evaluate the effect of external magnetic field on crater depth and diameter in single- and multiple-discharge EDM process. The model incorporates three main effects of the magnetic field, which include plasma confinement, mean free path reduction and pulsating magnetic field effects. Upon the application of an external magnetic field, Lorentz forces that are developed across the plasma column confine the plasma column. Also, the magnetic field reduces the mean free path of electrons due to an increase in the plasma pressure and cycloidal path taken by the electrons between the electrodes. As the mean free path of electrons reduces, more ionization occurs in plasma column and eventually an increase in the current density at the inter-electrode gap occurs. The model results for crater depth and its diameter in single discharge dry EDM process show an error of 9%-10% over the respective experimental values.
文摘An integrated CAD/CAPP/CAM system modeling for Electric Discharge Machining (EDM) is constructed on the basis of an integrated engineering database. EDM feature objects are developed using the object oriented database provided by AutoCAD R14, and EDM feature modeling is realized in AutoCAD environments.
文摘This paper introduces a study on modelling surface finish in EDM （Electrical Discharge Machining） of tablet shape punches when using copper as electrode material. In this study, 27 experiments were performed based on BBD （Box-Behnken Design） and the work-piece material was 9CrSi steel. The input process parameters were the current, the pulse on time, the pulse off time and the voltage. The effects of the input parameters on the surface finish were evaluated by analysing variance. Besides, from the results of the experiments, a regression equation for determining the surface roughness is introduced. Also, the optimum input parameter values were found in order to get the minimum surface roughness.
文摘This machine toolis one of the new products developed and produced by the Shanghai No.8 Machine Tool Plant on the basis of advanced technologies introduced from at home and abroad. It has a wide machining travel and large volume of oil box, and adopts the stepping motor main spindle servo-controlled mechanism, which has the advantages of sensitive control, quick response speed, stable working state, simple structure,
文摘The machining of small holes and array holes has been a difficult problem in machining field. Tiny hole is widely used in mechanical field, for instance, fuel injection nozzles, spinneret holes for synthetic fibers and wire drawing dies. This paper investigated the application of EDM (electrical discharge machining) to the fabrication of micro structures. There are obvious limitations in the process of micro-electrical discharge machining, such as electrode wear, unstable discharge condition and low machining efficiency. The effects of EDM parameters were investigated, such as voltage, pulse frequency, and frequency of ultrasonic vibration applied to electrode. Micro holes were machined with Pt electrode made by focused-ion-beam chemical vapor deposition (FIB-CVD) and Cu electrode made by wire-electrode cutting. The comparison experiments between EDM and ECM (electrochemical machining) indicated that the processing of ECM has serious stray current corrosion and poor machining precision. Moreover, the workpiece vibration was firstly proposed to be utilized in the micro-electrical discharge machining. It can be concluded that maximum machine could be obtained under the amplitude ratio of 76%, which was an appropriate parameter.
