The mechanism of slag entrapment in the mould was analyzed and the water modeling experiment was done according to the industrial manufacturing. The results show that the flow of the liquid steel becomes more active a...The mechanism of slag entrapment in the mould was analyzed and the water modeling experiment was done according to the industrial manufacturing. The results show that the flow of the liquid steel becomes more active and the level fluctuation in the mould becomes bigger when the casting speed increases from 1.0 m/min to 1.2 m/min. So the control of slag entrapment in the mould becomes more difficult. When the depth of the nozzle increases from 30mm to 42. 5mm and the angle increases from 15~ downward to 30° downward, the level fluctuation in the mould becomes smaller and the slag entrapment in the mould also decreases. But the impact depth increases and the circumfluence vortex center moves downward, which is unfavorable for the flotation of gas bubbles and inclusions. Furthermore, the impact depth with side holes a （ 16.3 × 20mm2 ） and b （ 10 × 10 mm2 ） is almost equal, but a smaller level fluctuation can be obtained with side hole a.展开更多
Based on the effects of several casting parameters on slag entrapment in the mould （ water modeling）, the numerical modeling was researched. The results show that the flow field with a submerged nozzle section dimen...Based on the effects of several casting parameters on slag entrapment in the mould （ water modeling）, the numerical modeling was researched. The results show that the flow field with a submerged nozzle section dimension of 65 mm ×80 mm is better than that with a submerged nozzle section dimension of 40 mm × 40 mm and is favorable for avoiding slag entrapment. In this paper, low surface velocity, small level fluctuation and proper impact depth can be achieved with a nozzle of an outlet angle of 25° and an immersion depth of 150 mm, or with a prototype nozzle of an outlet angle of 15° angle and an immersion depth of 150 mm.展开更多
The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhan...The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.展开更多
On the basis of the practical production of non-oriented silicon steel, the formation of Mg O·Al2O3 inclusions was analyzed in the process of ＂basic oxygen furnace（BOF） → RH → compact strip production（CSP）...On the basis of the practical production of non-oriented silicon steel, the formation of Mg O·Al2O3 inclusions was analyzed in the process of ＂basic oxygen furnace（BOF） → RH → compact strip production（CSP）＂. The thermodynamic and kinetic conditions of the formation of Mg O·Al2O3 inclusions were discussed, and the behavior of slag entrapment in molten steel during RH refining was simulated by computational fluid dynamics（CFD） software. The results showed that the Mg O/Al2O3 mass ratio was in the range from 0.005 to 0.017 and that Mg O·Al2O3 inclusions were not observed before the RH refining process. In contrast, the Mg O/Al2O3 mass ratio was in the range from 0.30 to 0.50, and the percentage of Mg O·Al2O3 spinel inclusions reached 58.4% of the total inclusions after the RH refining process. The compositions of the slag were similar to those of the inclusions; furthermore, the critical velocity of slag entrapment was calculated to be 0.45 m·s^-1 at an argon flow rate of 698 L·min^-1, as simulated using CFD software. When the test steel was in equilibrium with the slag, [Mg] was 0.00024wt%–0.00028wt% and [Al]s was 0.31wt%–0.37wt%; these concentrations were theoretically calculated to fall within the Mg O·Al2O3formation zone, thereby leading to the formation of Mg O·Al2O3 inclusions in the steel. Thus, the formation of Mg O·Al2O3 inclusions would be inhibited by reducing the quantity of slag entrapment, controlling the roughing slag during casting, and controlling the composition of the slag and the Mg O content in the ladle refractory.展开更多
The fluid flow and the interfacial phenomenon of slag and metal in tundish with gas blowing were studied with mathematical and physical modeling, and the effects of gas flowrate, the placement of porous beam for the g...The fluid flow and the interfacial phenomenon of slag and metal in tundish with gas blowing were studied with mathematical and physical modeling, and the effects of gas flowrate, the placement of porous beam for the generation of bubbles, and the combination of flow control devices on the flow and slag-metal interface were investigated. The results show that the position of gas bubbling has a significant effect on the flow in tundish, and the placement of porous beam and gas flowrate are the two main factors affecting the entrapment of slag in tundish. The closer the porous beam to the weir, the more reasonable is the flow, which is in favor of the control of slag entrapment in tundish.展开更多
Utilizing ANSYS CFX commercial software and volume fraction of fluid （VOF） model, fluctuation behav- ior of steel/slag interface was numerically simulated in continuous casting mold with static magnetic field, and t...Utilizing ANSYS CFX commercial software and volume fraction of fluid （VOF） model, fluctuation behav- ior of steel/slag interface was numerically simulated in continuous casting mold with static magnetic field, and the influence of metal jet characteristics on the behavior of steel/slag interface was investigated. The results indicated that the behavior of steel/slag interface is similar at different process parameters, which is closely related to the characteristic of the flow field. The steel/slag interface has an obvious trough characteristic, which can be divided in- to three zones： frontal valley zone, back valley zone and horizontal zone~ as the magnetic flux density increases, the fluctuation of liquid level increases firstly and then decreases, and a reasonable magnetic flux density can make steel/ slag interface obtain a relatively flat interface, which can prevent slag from being entrapped into liquid steel. For a thin slab continuous casting process, when the casting speed is 4 m/min, a reasonable magnetic flux density is about 0.5 T, and the interfacial fluctuation is weaker. No matter the position of magnetic field is horizontal or vertical, for different operating parameters, there is a corresponding reasonable magnetic field position where the steel/slag inter- face fluctuation can be properly controlled and slag entrapment can be prevented.展开更多
The level of the slag entrapment in mold involves the submerged nozzle immersion depth,the electromagnetic stirring intensity and other factors;this article has studied the relations between the slag entrapment behavi...The level of the slag entrapment in mold involves the submerged nozzle immersion depth,the electromagnetic stirring intensity and other factors;this article has studied the relations between the slag entrapment behavior and the above factors by using of the water model.The results show that the surface velocity in meniscus increases with the increasing of stirring intensity and the decreasing of submerged nozzle immersion depth.When the submerged nozzle immersion depth is shallower,and the stirring intensity is high,the interface turbulence of the molten steel and slag is more severe,slag entrapment may occur in the extreme state.In order to avoid the slag entrapment in the working condition,the submerged nozzle immersion depth should be increased from 85;0mm to 100mm,or the electric current of the electromagnetic stirring should be reduced from 320A to 295A.展开更多
To solve slag entrapment and casting slab defects in the process of stainless steel continuous casting,submerged entry nozzle(SEN)for slab casters operating at casting speed of 1 m/min was developed based on 3D numeri...To solve slag entrapment and casting slab defects in the process of stainless steel continuous casting,submerged entry nozzle(SEN)for slab casters operating at casting speed of 1 m/min was developed based on 3D numerical simulation and water modeling experiments by controlling the outlet shape and angle of original SEN with oval and 15°angle outlet under current industrial use.Mathematical simulations of fluid velocity at outlets with different shapes and angles of SENs have been carried out.The results showed that oval outlet with 5°and 15°angle led to asymmetric rotating flow pattern at outlet,as well as square outlet with 15°angle,but symmetric flow pattern formed at square outlet with 5°angle.The effect of these SENs on meniscus stability,flow field and slag entrapment behavior of stainless steel slab casting mold was further studied by water modeling experiments.The results showed that difficult floating fine droplets formed when the angle of outlet was 15°under the dual effect of vortex convection and shear force due to the strong swirling flow from outlet and rotating flow of outlet.However,outlet with 5°angle could lead to the formation of larger slag droplets,while the oval outlet with 5°angle could result in the scour to the mold wall.Thus,the square outlet with 5°angle was a relatively ideal solution for the submerged entry nozzle from the aspects of the stability of the mold and the slag entrapment behavior.After the design of a new SEN according to the experimental result,the solidification structure of continuous casting slab was obviously improved by industrial test.展开更多
文摘The mechanism of slag entrapment in the mould was analyzed and the water modeling experiment was done according to the industrial manufacturing. The results show that the flow of the liquid steel becomes more active and the level fluctuation in the mould becomes bigger when the casting speed increases from 1.0 m/min to 1.2 m/min. So the control of slag entrapment in the mould becomes more difficult. When the depth of the nozzle increases from 30mm to 42. 5mm and the angle increases from 15~ downward to 30° downward, the level fluctuation in the mould becomes smaller and the slag entrapment in the mould also decreases. But the impact depth increases and the circumfluence vortex center moves downward, which is unfavorable for the flotation of gas bubbles and inclusions. Furthermore, the impact depth with side holes a （ 16.3 × 20mm2 ） and b （ 10 × 10 mm2 ） is almost equal, but a smaller level fluctuation can be obtained with side hole a.
文摘Based on the effects of several casting parameters on slag entrapment in the mould （ water modeling）, the numerical modeling was researched. The results show that the flow field with a submerged nozzle section dimension of 65 mm ×80 mm is better than that with a submerged nozzle section dimension of 40 mm × 40 mm and is favorable for avoiding slag entrapment. In this paper, low surface velocity, small level fluctuation and proper impact depth can be achieved with a nozzle of an outlet angle of 25° and an immersion depth of 150 mm, or with a prototype nozzle of an outlet angle of 15° angle and an immersion depth of 150 mm.
文摘The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.
文摘On the basis of the practical production of non-oriented silicon steel, the formation of Mg O·Al2O3 inclusions was analyzed in the process of ＂basic oxygen furnace（BOF） → RH → compact strip production（CSP）＂. The thermodynamic and kinetic conditions of the formation of Mg O·Al2O3 inclusions were discussed, and the behavior of slag entrapment in molten steel during RH refining was simulated by computational fluid dynamics（CFD） software. The results showed that the Mg O/Al2O3 mass ratio was in the range from 0.005 to 0.017 and that Mg O·Al2O3 inclusions were not observed before the RH refining process. In contrast, the Mg O/Al2O3 mass ratio was in the range from 0.30 to 0.50, and the percentage of Mg O·Al2O3 spinel inclusions reached 58.4% of the total inclusions after the RH refining process. The compositions of the slag were similar to those of the inclusions; furthermore, the critical velocity of slag entrapment was calculated to be 0.45 m·s^-1 at an argon flow rate of 698 L·min^-1, as simulated using CFD software. When the test steel was in equilibrium with the slag, [Mg] was 0.00024wt%–0.00028wt% and [Al]s was 0.31wt%–0.37wt%; these concentrations were theoretically calculated to fall within the Mg O·Al2O3formation zone, thereby leading to the formation of Mg O·Al2O3 inclusions in the steel. Thus, the formation of Mg O·Al2O3 inclusions would be inhibited by reducing the quantity of slag entrapment, controlling the roughing slag during casting, and controlling the composition of the slag and the Mg O content in the ladle refractory.
基金Item Sponsored by National Natural Science Foundation of China (50674020)Program for New Century Excellent Talents in University (NCET-04-0285)
文摘The fluid flow and the interfacial phenomenon of slag and metal in tundish with gas blowing were studied with mathematical and physical modeling, and the effects of gas flowrate, the placement of porous beam for the generation of bubbles, and the combination of flow control devices on the flow and slag-metal interface were investigated. The results show that the position of gas bubbling has a significant effect on the flow in tundish, and the placement of porous beam and gas flowrate are the two main factors affecting the entrapment of slag in tundish. The closer the porous beam to the weir, the more reasonable is the flow, which is in favor of the control of slag entrapment in tundish.
基金Item Sponsored by National Natural Science Foundation of China(50604005,50834009)Natural Science Foundation of Liaoning Province of China(20102074)+2 种基金Fundamental Research Funds for the Central Universities of China(N100409005)Key Grant Project of Chinese Ministry of Education(311014)"111" Project of China(B07015)
文摘Utilizing ANSYS CFX commercial software and volume fraction of fluid （VOF） model, fluctuation behav- ior of steel/slag interface was numerically simulated in continuous casting mold with static magnetic field, and the influence of metal jet characteristics on the behavior of steel/slag interface was investigated. The results indicated that the behavior of steel/slag interface is similar at different process parameters, which is closely related to the characteristic of the flow field. The steel/slag interface has an obvious trough characteristic, which can be divided in- to three zones： frontal valley zone, back valley zone and horizontal zone~ as the magnetic flux density increases, the fluctuation of liquid level increases firstly and then decreases, and a reasonable magnetic flux density can make steel/ slag interface obtain a relatively flat interface, which can prevent slag from being entrapped into liquid steel. For a thin slab continuous casting process, when the casting speed is 4 m/min, a reasonable magnetic flux density is about 0.5 T, and the interfacial fluctuation is weaker. No matter the position of magnetic field is horizontal or vertical, for different operating parameters, there is a corresponding reasonable magnetic field position where the steel/slag inter- face fluctuation can be properly controlled and slag entrapment can be prevented.
文摘The level of the slag entrapment in mold involves the submerged nozzle immersion depth,the electromagnetic stirring intensity and other factors;this article has studied the relations between the slag entrapment behavior and the above factors by using of the water model.The results show that the surface velocity in meniscus increases with the increasing of stirring intensity and the decreasing of submerged nozzle immersion depth.When the submerged nozzle immersion depth is shallower,and the stirring intensity is high,the interface turbulence of the molten steel and slag is more severe,slag entrapment may occur in the extreme state.In order to avoid the slag entrapment in the working condition,the submerged nozzle immersion depth should be increased from 85;0mm to 100mm,or the electric current of the electromagnetic stirring should be reduced from 320A to 295A.
文摘To solve slag entrapment and casting slab defects in the process of stainless steel continuous casting,submerged entry nozzle(SEN)for slab casters operating at casting speed of 1 m/min was developed based on 3D numerical simulation and water modeling experiments by controlling the outlet shape and angle of original SEN with oval and 15°angle outlet under current industrial use.Mathematical simulations of fluid velocity at outlets with different shapes and angles of SENs have been carried out.The results showed that oval outlet with 5°and 15°angle led to asymmetric rotating flow pattern at outlet,as well as square outlet with 15°angle,but symmetric flow pattern formed at square outlet with 5°angle.The effect of these SENs on meniscus stability,flow field and slag entrapment behavior of stainless steel slab casting mold was further studied by water modeling experiments.The results showed that difficult floating fine droplets formed when the angle of outlet was 15°under the dual effect of vortex convection and shear force due to the strong swirling flow from outlet and rotating flow of outlet.However,outlet with 5°angle could lead to the formation of larger slag droplets,while the oval outlet with 5°angle could result in the scour to the mold wall.Thus,the square outlet with 5°angle was a relatively ideal solution for the submerged entry nozzle from the aspects of the stability of the mold and the slag entrapment behavior.After the design of a new SEN according to the experimental result,the solidification structure of continuous casting slab was obviously improved by industrial test.
