Nowadays buildings contain innovative materials,materials from local resources,production surpluses and rapidly renewable natural resources.Phase Change Materials(PCM)are one such group of novel materials which reduce...Nowadays buildings contain innovative materials,materials from local resources,production surpluses and rapidly renewable natural resources.Phase Change Materials(PCM)are one such group of novel materials which reduce building energy consumption.With the wider availability of microencapsulated PCM,there is an opportunity to develop a new type of insulating materials,combinate PCM with traditional insulation materials for latent heat energy storage.These materials are typically flammable and are located on the interior wall finishing yet there has been no detailed assessment of their fire performance.In this research work prototypes of low-density insulating boards for indoor spaces from hemp shives using carbamide resin binder and cold pressing were studied.Bench-scale cone calorimeter tests were conducted to evaluate fire risk,with a focus on assessing material flammability properties and the influence of PCM on the results.In this research,the amount of smoke,heat release rate,effective heat of combustion,specific extinction coefficient,mass loss,carbon dioxide yield,specific loss factor,ignition time of hemp straws samples and samples of hemp straws with 10%and without PCM admixture were compared.There is a risk of flammability for PCM and their fire reaction has not been evaluated when incorporating PCM into interior wall finishing boards.The obtained results can be used by designers to balance the potential energy savings of using PCM with a more complete understanding and predictability of the associated fire risk when using the proposed boards.It also allows for appropriate risk mitigation strategies.展开更多
This study deals with the analysis of dynamic mechanical,thermal and flammability properties of treated and untreated pineapple leaf fiber(PALF)and kenaf fiber(KF)phenolic composites.Results indicated that storage mod...This study deals with the analysis of dynamic mechanical,thermal and flammability properties of treated and untreated pineapple leaf fiber(PALF)and kenaf fiber(KF)phenolic composites.Results indicated that storage modulus was decreased for all composites with increases in temperature and pattern of slopes for all composites,having almost the same values of E′at glass transition temperature(Tg).The peak of the loss modulus of pure phenolic composites was shown to be much less.After the addition of kenaf/PALF,peaks were higher and shifted towards a high temperature.The Tan delta peak height was low for pure phenolic composites and maximum for 60%PALF phenolic composites.Cole-Cole analysis was carried out to understand the phase behavior of the composite samples.Thermogravimetric analysis(TGA)results indicated that pure phenolic composites have better thermal stability than PALF and kenaf phenolic composites.Vertical and horizontal UL-94 tests were conducted and showed pure phenolic resin is highly fire resistant.The overall results showed that treated KF composites enhanced the dynamic mechanical and thermal properties among all PALF/KF composites.展开更多
Thermal and flammability properties of acrylonitrile-butadiene-styrene copolymer (ABS) with the addition of multi-walled carbon nanotubes (MWNTs) were studied.ABS/MWNTs composites were prepared via melt blending with ...Thermal and flammability properties of acrylonitrile-butadiene-styrene copolymer (ABS) with the addition of multi-walled carbon nanotubes (MWNTs) were studied.ABS/MWNTs composites were prepared via melt blending with the MWNTs content varied from 0.2% to 4.0% by mass.Thermogravimetry results showed that the addition of MWNTs accelerated the degradation of ABS during the whole process under air atmosphere,and both onset and maximum degradation temperature were lower than those of pure ABS.The destabilizat...展开更多
Background:Flammability is a compound plant trait that can vary significantly across natural populations within species.Investigating intraspecific variation in flammability provides insights into the evolution of pla...Background:Flammability is a compound plant trait that can vary significantly across natural populations within species.Investigating intraspecific variation in flammability provides insights into the evolution of plant flam-mability and inform understanding of wildfire risk and behaviour in different habitats.Methods:We measured four flammability variables,representing ignitibility(time to ignition),sustainability(total burning time),combustibility(maximum temperature during burning)and consumability(percentage of biomass consumed by fire)to assess the shoot-level flammability of Dracophyllum rosmarinifolium(G.Forst.)(Ericaceae),a polymorphic endemic species distributed throughout New Zealand.We examined the relationship between flammability components and a suite of climatic and geographic variables(elevation,latitude,mean annual temperature(MAT),mean annual rainfall(MAR)of the sample locations,etc.).Results:We measured shoot-level flammability components of 62 individuals across eight populations.Burning time,maximum temperature and burnt biomass were positively correlated with each other,while ignition score was independent of other flammability components.All flammability components varied significantly across the eight populations.The habitat conditions we considered were not related to any of the shoot-level flammability components of D.rosmarinifolium.Conclusions:Intraspecific variation in flammability in D.rosmarinifolium may be a byproduct of selection on other functional traits,such as leaf size,shoot lipid content,indicating that plant flammability is an incidental result,rather than selected for,at least in ecosystems without fire as a selective force.展开更多
A small cubic closed vessel with schlieren measurement technique combined with high-speed video camera were used to study limit flame properties under microgravity conditions at atmospheric pressure and room temperatu...A small cubic closed vessel with schlieren measurement technique combined with high-speed video camera were used to study limit flame properties under microgravity conditions at atmospheric pressure and room temperature.The rich flammability limit of C3H8/air was determined to be 9.2% C3H8.Stretched flame propagation speeds,stretched laminar burning velocities and unstretched laminar burning velocities near rich C3H8/air flammability limits were measured at different equivalence ratios.Outwardly propagating spherical flames were used to study the sensitivities of the flame propagation speeds and laminar burning velocities to flame stretch using Markstein lengths.Unstretched laminar burning velocity at rich flammability limit was determined to be 1.09cm/s.Lewis numbers were less than unity in rich C3H8/air and negative Markstein lengths were concluded.Absolute values of Markstein lengths were found to decrease linearly with equivalence ratios increase.展开更多
Flammability properties of composites of wood fiber and recycled plastic were evaluated by the cone calorimeter and oxygen index chamber. Results were shown as follows: 1) Wood-PVC composite showed worse thermal stabi...Flammability properties of composites of wood fiber and recycled plastic were evaluated by the cone calorimeter and oxygen index chamber. Results were shown as follows: 1) Wood-PVC composite showed worse thermal stability on time to ignition (TTI) and mean heat release rate (MHRR), but better performance on heat release rate (HRR) and mean efficient heat of combustion (MEHC); wood-PP composite had better thermal stability properties, but was worse on other fire performance; 2) Compared with wood-PVC composite, wood-PP composite showed excellent thermal stability, but behaved dangerous as a whole; 3) Coupling agent PAPI changed fire performance of wood-PP composite and showed a longer TTI, lower EHC but higher HRR. It can be concluded that flame resistance treatment should be considered if wood-plastic composites are used as decorated materials.展开更多
In the present study, a novel model is proposed to evaluate the lower flammability limit(LFL) of alkane diluted with CO2. The LFL model is based on flame phenomenon simulation(FS-LFL). The model consists of combustion...In the present study, a novel model is proposed to evaluate the lower flammability limit(LFL) of alkane diluted with CO2. The LFL model is based on flame phenomenon simulation(FS-LFL). The model consists of combustion, turbulence, and igniter models, which are used to characterise the combustion based on the chemical kinetics and CFD, which is not feasible with traditional methods. The flame simulation phenomenon was validated by contrast with experiment and same criterion of flammability limit in the experiment was adopted. The FS-LFL model was used to predict the LFLs of a propane-CO2 mixture and propane at various temperatures. The model performance was analysed by comparing the results with experimental data and predictions obtained from existing methods. The AARDs between the predicted and experimentally determined LFLs of the propane-CO2 mixture are 0.34%, 1.19%, and 1.35% at 30℃, 50℃, and 70℃, respectively. The model also has a good predictive power with respect to the LFLs of propane at initial temperatures ranging from 30℃–300℃, with an AARD of 2.10%. When the dilution of CO2 is 90%, the model yields a better result due to the utilisation of the chemical kinetics mechanism. This result is instructive for the use of this method in the prediction of upper flammability limits.展开更多
As group contribution method is easy to apply and has a wide application range,current study has developed this model to predict flammability limit of hydrocarbons mixed with inert gas using the Marrero/Gani group con...As group contribution method is easy to apply and has a wide application range,current study has developed this model to predict flammability limit of hydrocarbons mixed with inert gas using the Marrero/Gani group contribution method,which is significative to the safe application of hydrocarbons in the ORC system.The whole modeling process is divided into two parts:pure compound prediction and mixture prediction.The contribution factors of inert gases and dilute concentration were first introduced in the group contribution method.Moreover,the respective 95%-confidence interval of the mixture based on linear superposition method has been proposed in the developed group contribution model to improve the safety coefficient.For CO2 as inert gas,the average relative error and correlation coefficient are 5.34%and 0.88 for lower flammability limit while 6.99%and 0.95 for upper flammability limit.For N2 as inert gas,the average relative error and correlation coefficient are 7.47%and 0.84 for lower flammability limit while 6.68%and 0.97 for upper flammability limit.Most importantly,this group contribution method has extended the application range to make up the shortcomings of other flammability limit prediction methods aiming at hydrocarbon and inert gas mixtures and proposed the uncertainty analysis to provide reliable prediction range.展开更多
The contradiction between flammability and packing density is the technical bottleneck for combustible smoke agent.Herein,polyurethane(PU)foams with flammability and resilience were prepared with polyol and isocyanate...The contradiction between flammability and packing density is the technical bottleneck for combustible smoke agent.Herein,polyurethane(PU)foams with flammability and resilience were prepared with polyol and isocyanate as raw materials by chemical foaming method,then compounded with metal powders,polytetrafluoroethylene(PTFE),phthalic annychide(PA),etc.in a certain proportion and pressed into pyrotechnic grain to obtain eco-friendly combustion aerosols with compact density of about1.15 g/cm^(3).The resulting combustion smoke agent combined the advantages of PU foam and pyrotechnic with easy ignition,large smoke production,long duration and low environmental pollution.The transmittance of aerosols for 532 nm and 1064 nm lasers was close to 0,and the EMI SE reached up to65 d B and 35 d B in GPS band and X band,respectively.In addition,the resulting pyrotechnic grains exhibited good mechanical strength and elasticity for sample 1:25,with a compressive strength of22 MPa and an elastic modulus of 195 MPa.The resulting combustion smoke agent is expected to play a potential role in the field of electromagnetic damage and protection.展开更多
This work reports on the effect of commercial expandable graphite(EG)on the flammability and thermal decomposition properties of PLA-starch blend.The PLA-starch/EG composites were prepared by melt-mixing and their the...This work reports on the effect of commercial expandable graphite(EG)on the flammability and thermal decomposition properties of PLA-starch blend.The PLA-starch/EG composites were prepared by melt-mixing and their thermal stability,volatile pyrolysis products and flammability characteristics were investigated.The char residues of the composites,after combustion in a cone calorimeter,were analyzed with environmental scanning electron microscopy(ESEM).The thermal decomposition stability of the composites improved in the presence of EG.However,the char content was less than expected as per the combination of the wt%EG added into PLA-starch and the%residue of PLA-starch.The flammability performance of the PLA-starch/EG composites improved,especially at 15 wt%EG content,due to a thick and strong worm-like char structure.The peak heat release rate(PHRR)improved by 74%,the total smoke production(TSP)by 40%and the specific extinction area(SEA)by 55%.The improvements are attributed to the ability of EG to exfoliate at increased temperatures during which time three effects occurred:(i)cooling due to an endothermic exfoliation process,(ii)dilution due to release of H2O,SO2 and CO2 gases,and (iii)formation of a protective intumescent char layer.However,the CO and CO2 yields were found to be unfavorably high due to the presence of EG.展开更多
To better manage wildfires and plantations in Kurdistan,native tree species commonly used in planting and reviving forests such as Quercus brantii Lindl.,Q.infectoria Olivier,Q.libani Olivier,Pistachio atlantica Desf....To better manage wildfires and plantations in Kurdistan,native tree species commonly used in planting and reviving forests such as Quercus brantii Lindl.,Q.infectoria Olivier,Q.libani Olivier,Pistachio atlantica Desf.,Fraxinus rotundifolia Vahl,and Robinia pseudoacacia L.were evaluated and compared in terms of fire sensitivity and fire resistance.To determine fire sensitivity,indices such as the fl ammability index,ignition time,fl ame durability,moisture content,carbonized surface,mass reduction,bulk density,as well as dry weight of wood,bark,and leaves were used.The data were subjected to ANOVA.The means obtained,after examining homogeneity or heterogeneity of the variances,were compared using parametric and nonparametric comparison tests.There was a significant difference at the level of 5%.Based on the analysis of these indices,the species could be divided into three groups:species sensitive to fire such as Robinia pseudoacacia,species moderately sensitive to fire such as F.rotundifolia,and species relatively resistant to fire,including Q.brantii,Q.libani,Q.infectoria,and P.atlantica.展开更多
A battery concept based on the chemical system of magnesium (anode) and persulfate (cathode) is presented. A complete procedure is given to prepare the battery for testing, although no experimental data is presented h...A battery concept based on the chemical system of magnesium (anode) and persulfate (cathode) is presented. A complete procedure is given to prepare the battery for testing, although no experimental data is presented herein. The similarities of this system to a well-tested Li||LiFePO4 system lend strong credibility to the concept, and the estimated performance characteristics presented. The advantages of this design include the following many areas. First, inexpensive, and available, battery reagents exist. Second, by analogy to the lithium ion battery for which comparisons are made, the full fabrication process for battery separator design is known and efficient;and both the kJ/kg and Amps/kg values are estimated to be substantially larger than the lithium ion battery (e.g., Li||LiFePO4) experimental design. Finally, flammability of the Mg||MgS2O8 system can be expected to provide less of a potential flammability concern, compared to comparable lithium ion batteries. This is because lithium metal, as with any alkali metal, is aggressively flammable even under reduced moisture environments. The proposed magnesium persulfate battery calculated metrics yield an improvement of 194% greater output power (W/cm2·kg), and 154% greater stored energy (MJ/kg) than state-of-the-art lithium iron phosphate batteries.展开更多
A method is described, that allows a quick and simple testing of the burning behaviour of plastics. It takes into account ignition time as well as afterflame time;properties that are characteristic for the burning beh...A method is described, that allows a quick and simple testing of the burning behaviour of plastics. It takes into account ignition time as well as afterflame time;properties that are characteristic for the burning behaviour of a particular plastic material. The procedure is easy to perform, it does neither require injection-moulded samples nor expensive equipment. The method provides a classification of the burning behaviour. It is especially suitable for a screening of plastic materials complementing established methods like UL-94, GWFI and LOI, and may find application in the development of flame retardants.展开更多
<div style="text-align:justify;"> <span style="font-family:Verdana;">The use of vegetable fibers composites in structures sometimes presents significant fires risks because of their hig...<div style="text-align:justify;"> <span style="font-family:Verdana;">The use of vegetable fibers composites in structures sometimes presents significant fires risks because of their high flammability. This work aims to study the impact of the addition of mineral filler (clay) on the fire behaviour of wood-polystyrene composites and their mechanical properties. Thus, composites containing 25% of expanded polystyrene binder have been produced. On this base material, proportions of clay ranging from 0% to 15% were gradually added. These samples were elaborated by compaction and for some them, submitted to thermoforming after drying. Both kinds of sample were subjected to flame persistence test;flexural strength and compressive strength test were also measured. The results show that composites without mineral filler ignite continuously until the total consumption and when the mineral filler content increases the combustion time decreases. The addition of the mineral filler allows these composites to pass from class M3 of moderately flammable combustible materials to class M2 of hardly flammable materials, according to the M classification of construction and furnishing materials. The measurement of the mechanical properties shows that the strengths increase when the filler content goes from 0% to 10% and then decrease. This leads to set the optimum content of mineral filler around 10%.</span> </div>展开更多
In order to reduce the number of accidents due to explosions of flammable gases in the goaf of coalmines,the conditions for explosion of flammable gases and their explosion limits,affected to a considerable extent by ...In order to reduce the number of accidents due to explosions of flammable gases in the goaf of coalmines,the conditions for explosion of flammable gases and their explosion limits,affected to a considerable extent by CO2,are explored.With the use of our experimental equipment suitable for the study of explosion of polybasic explosive gas mixtures,we investigated the effect of CH4/H2=10/1 and CH4/C2H4=10/1 gases mixed with CO2 on their explosion limits.The results indicate that after adding CO2,the explosion limit of the CH4/H2(or C2H4) =10/1 gas mixtures decreased markedly with increasing amounts of CO2.When the amount of CO2 exceeded 25%,the CH4/C2H4=10/1 flammable gas mixture did not lead to explosions.Similar results were obtained when the amount of CO2 exceeded 23% in the CH4/H2=10/1 flammable gas mixture.We also compared the explosion limits and the explosion suppression effect of N2 or CO2 on the explosion limits of the CH4+CO and CH4+C2H4 dual explosive gas mixtures.Along with the increases in the amounts of CO2 or N2,the area of the explosion limits of gas mixtures decreased.Under the same conditions,the explosion suppression effect of CO2 was greater than that of N2.CO2 has clearly the better suppression effect on the explosion of flammable gases in goafs.展开更多
This study aimed to describe a Computational Fluid Dynamics(CFD) procedure using the ANSYS CFX software 16.1 and Design of Experiments for the determination of volume and extension of explosive atmospheres due to fugi...This study aimed to describe a Computational Fluid Dynamics(CFD) procedure using the ANSYS CFX software 16.1 and Design of Experiments for the determination of volume and extension of explosive atmospheres due to fugitive emissions of flammable gases.The multidimensional statistical sampling technique Latin Hypercube was used, which defined 100 simulations of random methane gas leak conditions.The CFD model proved to be robust in predicting the extension and volume of the explosive atmosphere for orifice diameters from 0.1 to2.5 mm, pressure from 0.1 MPa to 12 MPa and temperatures from 0 ℃ to 400 ℃.It was found that the calculation domain must be parameterized 8 m in length for each millimeter of the diameter of the source of release to ensure the predictions.In order not to lose precision for very small diameters, the mesh was parameterized with 50 elements along the orifice diameter.It was proved that gravity does not influence the extension and volume of the explosive atmosphere at sonic emissions.The deviation from the ideal gas behavior in the reservoir,achieved by applying the Soave–Redlich–Kwong equation of state, also has not significantly influenced the extension and volume of the explosive atmosphere.The results showed that the size of the explosive atmosphere varies directly with the diameter of the source emission and reservoir pressure, and inversely with the temperature of the reservoir.The diameter of the source is the parameter that has the major effect on the extension of the explosive atmosphere, followed by the pressure and lastly the temperature of the reservoir.展开更多
An incinerator was built up in 1987 in Shanghai. In this paper, the devices of the incinerator, main parameters of the process, the results of combustion tests for nonradioactive waste and simulated radwaste are given...An incinerator was built up in 1987 in Shanghai. In this paper, the devices of the incinerator, main parameters of the process, the results of combustion tests for nonradioactive waste and simulated radwaste are given. The instructive information for radwaste treatment were provided.展开更多
<div style="text-align:justify;"> In order to reduce the arson or accidental fire losses, we developed a gas sensitive detector used for the rapid detection and early warning of flammables in crowded p...<div style="text-align:justify;"> In order to reduce the arson or accidental fire losses, we developed a gas sensitive detector used for the rapid detection and early warning of flammables in crowded places such as buses. A MEMS (Micro-Electro-Mechanical System) based thin film semiconductor was fabricated as the gas sensor. To obtain the target gas selective response, the surface of the sensitive film was modified with highly active metal catalytic nano-particles. Thus the anti-interference ability was improved and the false alarm rate was effectively reduced. Furthermore, the modular embedded system for information acquisition and transmission was developed. Supported by the Airflow Precision control system (APs), the rapid warning of volatile gas of flammable substances was realized. Experiments showed that RAs has satisfied selectivity to volatiles of usual flammable liquid, such as the output voltage reaches 3 V (0 - 3.3 V). With simulation about the actual installation state in bus, MWs sounds an alarm at 2 minutes after splashing 50 mL 92# petrol to the floor. For the last two years, FEVMEW has been integrated into more than 4000 buses in Hefei. This design has been proved feasible according to the actual operation. </div>展开更多
Wireless Sensor Network based on ZigBee technology is a wireless network which is composed of many nodes of ZigBee RF chips, sensors and MCUs, especially suitable for application of the remote monitoring system in fla...Wireless Sensor Network based on ZigBee technology is a wireless network which is composed of many nodes of ZigBee RF chips, sensors and MCUs, especially suitable for application of the remote monitoring system in flammable and explosive environments. This paper presents the characteristics and advantages of ZigBee technology, also discusses the system for hardware and software design. This system effectively fulfills the remote monitoring in flammable and explosive environments and posses high practical values.展开更多
基金supported by the European Regional Development Fund Postdoctoral Research Support“Structures and Technology Development of Smart Insulation Materials for Indoor Microclimate Regulation”1.1.1.2/VIAA/1/16/152the European Social Fund within the Project“Development of the Academic Personnel of Riga Technical University in the Strategic Fields of Specialization”Nr.8.2.2.0/18/A/017.
文摘Nowadays buildings contain innovative materials,materials from local resources,production surpluses and rapidly renewable natural resources.Phase Change Materials(PCM)are one such group of novel materials which reduce building energy consumption.With the wider availability of microencapsulated PCM,there is an opportunity to develop a new type of insulating materials,combinate PCM with traditional insulation materials for latent heat energy storage.These materials are typically flammable and are located on the interior wall finishing yet there has been no detailed assessment of their fire performance.In this research work prototypes of low-density insulating boards for indoor spaces from hemp shives using carbamide resin binder and cold pressing were studied.Bench-scale cone calorimeter tests were conducted to evaluate fire risk,with a focus on assessing material flammability properties and the influence of PCM on the results.In this research,the amount of smoke,heat release rate,effective heat of combustion,specific extinction coefficient,mass loss,carbon dioxide yield,specific loss factor,ignition time of hemp straws samples and samples of hemp straws with 10%and without PCM admixture were compared.There is a risk of flammability for PCM and their fire reaction has not been evaluated when incorporating PCM into interior wall finishing boards.The obtained results can be used by designers to balance the potential energy savings of using PCM with a more complete understanding and predictability of the associated fire risk when using the proposed boards.It also allows for appropriate risk mitigation strategies.
文摘This study deals with the analysis of dynamic mechanical,thermal and flammability properties of treated and untreated pineapple leaf fiber(PALF)and kenaf fiber(KF)phenolic composites.Results indicated that storage modulus was decreased for all composites with increases in temperature and pattern of slopes for all composites,having almost the same values of E′at glass transition temperature(Tg).The peak of the loss modulus of pure phenolic composites was shown to be much less.After the addition of kenaf/PALF,peaks were higher and shifted towards a high temperature.The Tan delta peak height was low for pure phenolic composites and maximum for 60%PALF phenolic composites.Cole-Cole analysis was carried out to understand the phase behavior of the composite samples.Thermogravimetric analysis(TGA)results indicated that pure phenolic composites have better thermal stability than PALF and kenaf phenolic composites.Vertical and horizontal UL-94 tests were conducted and showed pure phenolic resin is highly fire resistant.The overall results showed that treated KF composites enhanced the dynamic mechanical and thermal properties among all PALF/KF composites.
文摘Thermal and flammability properties of acrylonitrile-butadiene-styrene copolymer (ABS) with the addition of multi-walled carbon nanotubes (MWNTs) were studied.ABS/MWNTs composites were prepared via melt blending with the MWNTs content varied from 0.2% to 4.0% by mass.Thermogravimetry results showed that the addition of MWNTs accelerated the degradation of ABS during the whole process under air atmosphere,and both onset and maximum degradation temperature were lower than those of pure ABS.The destabilizat...
基金This work was supported by Lincoln University faculty funding(NO.3601-AGLS-45401-1128912).
文摘Background:Flammability is a compound plant trait that can vary significantly across natural populations within species.Investigating intraspecific variation in flammability provides insights into the evolution of plant flam-mability and inform understanding of wildfire risk and behaviour in different habitats.Methods:We measured four flammability variables,representing ignitibility(time to ignition),sustainability(total burning time),combustibility(maximum temperature during burning)and consumability(percentage of biomass consumed by fire)to assess the shoot-level flammability of Dracophyllum rosmarinifolium(G.Forst.)(Ericaceae),a polymorphic endemic species distributed throughout New Zealand.We examined the relationship between flammability components and a suite of climatic and geographic variables(elevation,latitude,mean annual temperature(MAT),mean annual rainfall(MAR)of the sample locations,etc.).Results:We measured shoot-level flammability components of 62 individuals across eight populations.Burning time,maximum temperature and burnt biomass were positively correlated with each other,while ignition score was independent of other flammability components.All flammability components varied significantly across the eight populations.The habitat conditions we considered were not related to any of the shoot-level flammability components of D.rosmarinifolium.Conclusions:Intraspecific variation in flammability in D.rosmarinifolium may be a byproduct of selection on other functional traits,such as leaf size,shoot lipid content,indicating that plant flammability is an incidental result,rather than selected for,at least in ecosystems without fire as a selective force.
基金Supported by the Research Foundation of Beijing Institute of Technology(20070242004)
文摘A small cubic closed vessel with schlieren measurement technique combined with high-speed video camera were used to study limit flame properties under microgravity conditions at atmospheric pressure and room temperature.The rich flammability limit of C3H8/air was determined to be 9.2% C3H8.Stretched flame propagation speeds,stretched laminar burning velocities and unstretched laminar burning velocities near rich C3H8/air flammability limits were measured at different equivalence ratios.Outwardly propagating spherical flames were used to study the sensitivities of the flame propagation speeds and laminar burning velocities to flame stretch using Markstein lengths.Unstretched laminar burning velocity at rich flammability limit was determined to be 1.09cm/s.Lewis numbers were less than unity in rich C3H8/air and negative Markstein lengths were concluded.Absolute values of Markstein lengths were found to decrease linearly with equivalence ratios increase.
文摘Flammability properties of composites of wood fiber and recycled plastic were evaluated by the cone calorimeter and oxygen index chamber. Results were shown as follows: 1) Wood-PVC composite showed worse thermal stability on time to ignition (TTI) and mean heat release rate (MHRR), but better performance on heat release rate (HRR) and mean efficient heat of combustion (MEHC); wood-PP composite had better thermal stability properties, but was worse on other fire performance; 2) Compared with wood-PVC composite, wood-PP composite showed excellent thermal stability, but behaved dangerous as a whole; 3) Coupling agent PAPI changed fire performance of wood-PP composite and showed a longer TTI, lower EHC but higher HRR. It can be concluded that flame resistance treatment should be considered if wood-plastic composites are used as decorated materials.
基金supported by the National Natural Science Foundation of China (Grant No. 51676133)。
文摘In the present study, a novel model is proposed to evaluate the lower flammability limit(LFL) of alkane diluted with CO2. The LFL model is based on flame phenomenon simulation(FS-LFL). The model consists of combustion, turbulence, and igniter models, which are used to characterise the combustion based on the chemical kinetics and CFD, which is not feasible with traditional methods. The flame simulation phenomenon was validated by contrast with experiment and same criterion of flammability limit in the experiment was adopted. The FS-LFL model was used to predict the LFLs of a propane-CO2 mixture and propane at various temperatures. The model performance was analysed by comparing the results with experimental data and predictions obtained from existing methods. The AARDs between the predicted and experimentally determined LFLs of the propane-CO2 mixture are 0.34%, 1.19%, and 1.35% at 30℃, 50℃, and 70℃, respectively. The model also has a good predictive power with respect to the LFLs of propane at initial temperatures ranging from 30℃–300℃, with an AARD of 2.10%. When the dilution of CO2 is 90%, the model yields a better result due to the utilisation of the chemical kinetics mechanism. This result is instructive for the use of this method in the prediction of upper flammability limits.
基金This work was supported by a grant from the National Natural Science Foundation of China(No.51676133)。
文摘As group contribution method is easy to apply and has a wide application range,current study has developed this model to predict flammability limit of hydrocarbons mixed with inert gas using the Marrero/Gani group contribution method,which is significative to the safe application of hydrocarbons in the ORC system.The whole modeling process is divided into two parts:pure compound prediction and mixture prediction.The contribution factors of inert gases and dilute concentration were first introduced in the group contribution method.Moreover,the respective 95%-confidence interval of the mixture based on linear superposition method has been proposed in the developed group contribution model to improve the safety coefficient.For CO2 as inert gas,the average relative error and correlation coefficient are 5.34%and 0.88 for lower flammability limit while 6.99%and 0.95 for upper flammability limit.For N2 as inert gas,the average relative error and correlation coefficient are 7.47%and 0.84 for lower flammability limit while 6.68%and 0.97 for upper flammability limit.Most importantly,this group contribution method has extended the application range to make up the shortcomings of other flammability limit prediction methods aiming at hydrocarbon and inert gas mixtures and proposed the uncertainty analysis to provide reliable prediction range.
基金financial support from the Fundamental Research Funds for the Central Universities(No.3090011182152)。
文摘The contradiction between flammability and packing density is the technical bottleneck for combustible smoke agent.Herein,polyurethane(PU)foams with flammability and resilience were prepared with polyol and isocyanate as raw materials by chemical foaming method,then compounded with metal powders,polytetrafluoroethylene(PTFE),phthalic annychide(PA),etc.in a certain proportion and pressed into pyrotechnic grain to obtain eco-friendly combustion aerosols with compact density of about1.15 g/cm^(3).The resulting combustion smoke agent combined the advantages of PU foam and pyrotechnic with easy ignition,large smoke production,long duration and low environmental pollution.The transmittance of aerosols for 532 nm and 1064 nm lasers was close to 0,and the EMI SE reached up to65 d B and 35 d B in GPS band and X band,respectively.In addition,the resulting pyrotechnic grains exhibited good mechanical strength and elasticity for sample 1:25,with a compressive strength of22 MPa and an elastic modulus of 195 MPa.The resulting combustion smoke agent is expected to play a potential role in the field of electromagnetic damage and protection.
文摘This work reports on the effect of commercial expandable graphite(EG)on the flammability and thermal decomposition properties of PLA-starch blend.The PLA-starch/EG composites were prepared by melt-mixing and their thermal stability,volatile pyrolysis products and flammability characteristics were investigated.The char residues of the composites,after combustion in a cone calorimeter,were analyzed with environmental scanning electron microscopy(ESEM).The thermal decomposition stability of the composites improved in the presence of EG.However,the char content was less than expected as per the combination of the wt%EG added into PLA-starch and the%residue of PLA-starch.The flammability performance of the PLA-starch/EG composites improved,especially at 15 wt%EG content,due to a thick and strong worm-like char structure.The peak heat release rate(PHRR)improved by 74%,the total smoke production(TSP)by 40%and the specific extinction area(SEA)by 55%.The improvements are attributed to the ability of EG to exfoliate at increased temperatures during which time three effects occurred:(i)cooling due to an endothermic exfoliation process,(ii)dilution due to release of H2O,SO2 and CO2 gases,and (iii)formation of a protective intumescent char layer.However,the CO and CO2 yields were found to be unfavorably high due to the presence of EG.
文摘To better manage wildfires and plantations in Kurdistan,native tree species commonly used in planting and reviving forests such as Quercus brantii Lindl.,Q.infectoria Olivier,Q.libani Olivier,Pistachio atlantica Desf.,Fraxinus rotundifolia Vahl,and Robinia pseudoacacia L.were evaluated and compared in terms of fire sensitivity and fire resistance.To determine fire sensitivity,indices such as the fl ammability index,ignition time,fl ame durability,moisture content,carbonized surface,mass reduction,bulk density,as well as dry weight of wood,bark,and leaves were used.The data were subjected to ANOVA.The means obtained,after examining homogeneity or heterogeneity of the variances,were compared using parametric and nonparametric comparison tests.There was a significant difference at the level of 5%.Based on the analysis of these indices,the species could be divided into three groups:species sensitive to fire such as Robinia pseudoacacia,species moderately sensitive to fire such as F.rotundifolia,and species relatively resistant to fire,including Q.brantii,Q.libani,Q.infectoria,and P.atlantica.
文摘A battery concept based on the chemical system of magnesium (anode) and persulfate (cathode) is presented. A complete procedure is given to prepare the battery for testing, although no experimental data is presented herein. The similarities of this system to a well-tested Li||LiFePO4 system lend strong credibility to the concept, and the estimated performance characteristics presented. The advantages of this design include the following many areas. First, inexpensive, and available, battery reagents exist. Second, by analogy to the lithium ion battery for which comparisons are made, the full fabrication process for battery separator design is known and efficient;and both the kJ/kg and Amps/kg values are estimated to be substantially larger than the lithium ion battery (e.g., Li||LiFePO4) experimental design. Finally, flammability of the Mg||MgS2O8 system can be expected to provide less of a potential flammability concern, compared to comparable lithium ion batteries. This is because lithium metal, as with any alkali metal, is aggressively flammable even under reduced moisture environments. The proposed magnesium persulfate battery calculated metrics yield an improvement of 194% greater output power (W/cm2·kg), and 154% greater stored energy (MJ/kg) than state-of-the-art lithium iron phosphate batteries.
文摘A method is described, that allows a quick and simple testing of the burning behaviour of plastics. It takes into account ignition time as well as afterflame time;properties that are characteristic for the burning behaviour of a particular plastic material. The procedure is easy to perform, it does neither require injection-moulded samples nor expensive equipment. The method provides a classification of the burning behaviour. It is especially suitable for a screening of plastic materials complementing established methods like UL-94, GWFI and LOI, and may find application in the development of flame retardants.
文摘<div style="text-align:justify;"> <span style="font-family:Verdana;">The use of vegetable fibers composites in structures sometimes presents significant fires risks because of their high flammability. This work aims to study the impact of the addition of mineral filler (clay) on the fire behaviour of wood-polystyrene composites and their mechanical properties. Thus, composites containing 25% of expanded polystyrene binder have been produced. On this base material, proportions of clay ranging from 0% to 15% were gradually added. These samples were elaborated by compaction and for some them, submitted to thermoforming after drying. Both kinds of sample were subjected to flame persistence test;flexural strength and compressive strength test were also measured. The results show that composites without mineral filler ignite continuously until the total consumption and when the mineral filler content increases the combustion time decreases. The addition of the mineral filler allows these composites to pass from class M3 of moderately flammable combustible materials to class M2 of hardly flammable materials, according to the M classification of construction and furnishing materials. The measurement of the mechanical properties shows that the strengths increase when the filler content goes from 0% to 10% and then decrease. This leads to set the optimum content of mineral filler around 10%.</span> </div>
基金provided by the National Natural Science Foundation of China (No.50874088)the Project of Creative Team by the Ministry of Education of China (No.IRT0856)+1 种基金the Excellent Talent Project of the New Century supported by the Ministry of Education of China (No.NECT050874)the Natural Science Foundation of the Education Department of Shaanxi Province (No.08JK351)
文摘In order to reduce the number of accidents due to explosions of flammable gases in the goaf of coalmines,the conditions for explosion of flammable gases and their explosion limits,affected to a considerable extent by CO2,are explored.With the use of our experimental equipment suitable for the study of explosion of polybasic explosive gas mixtures,we investigated the effect of CH4/H2=10/1 and CH4/C2H4=10/1 gases mixed with CO2 on their explosion limits.The results indicate that after adding CO2,the explosion limit of the CH4/H2(or C2H4) =10/1 gas mixtures decreased markedly with increasing amounts of CO2.When the amount of CO2 exceeded 25%,the CH4/C2H4=10/1 flammable gas mixture did not lead to explosions.Similar results were obtained when the amount of CO2 exceeded 23% in the CH4/H2=10/1 flammable gas mixture.We also compared the explosion limits and the explosion suppression effect of N2 or CO2 on the explosion limits of the CH4+CO and CH4+C2H4 dual explosive gas mixtures.Along with the increases in the amounts of CO2 or N2,the area of the explosion limits of gas mixtures decreased.Under the same conditions,the explosion suppression effect of CO2 was greater than that of N2.CO2 has clearly the better suppression effect on the explosion of flammable gases in goafs.
基金Petrobras (0050.0093154.14.9)–Petróleo Brasileiro S.A.for the financial and technical support
文摘This study aimed to describe a Computational Fluid Dynamics(CFD) procedure using the ANSYS CFX software 16.1 and Design of Experiments for the determination of volume and extension of explosive atmospheres due to fugitive emissions of flammable gases.The multidimensional statistical sampling technique Latin Hypercube was used, which defined 100 simulations of random methane gas leak conditions.The CFD model proved to be robust in predicting the extension and volume of the explosive atmosphere for orifice diameters from 0.1 to2.5 mm, pressure from 0.1 MPa to 12 MPa and temperatures from 0 ℃ to 400 ℃.It was found that the calculation domain must be parameterized 8 m in length for each millimeter of the diameter of the source of release to ensure the predictions.In order not to lose precision for very small diameters, the mesh was parameterized with 50 elements along the orifice diameter.It was proved that gravity does not influence the extension and volume of the explosive atmosphere at sonic emissions.The deviation from the ideal gas behavior in the reservoir,achieved by applying the Soave–Redlich–Kwong equation of state, also has not significantly influenced the extension and volume of the explosive atmosphere.The results showed that the size of the explosive atmosphere varies directly with the diameter of the source emission and reservoir pressure, and inversely with the temperature of the reservoir.The diameter of the source is the parameter that has the major effect on the extension of the explosive atmosphere, followed by the pressure and lastly the temperature of the reservoir.
文摘An incinerator was built up in 1987 in Shanghai. In this paper, the devices of the incinerator, main parameters of the process, the results of combustion tests for nonradioactive waste and simulated radwaste are given. The instructive information for radwaste treatment were provided.
文摘<div style="text-align:justify;"> In order to reduce the arson or accidental fire losses, we developed a gas sensitive detector used for the rapid detection and early warning of flammables in crowded places such as buses. A MEMS (Micro-Electro-Mechanical System) based thin film semiconductor was fabricated as the gas sensor. To obtain the target gas selective response, the surface of the sensitive film was modified with highly active metal catalytic nano-particles. Thus the anti-interference ability was improved and the false alarm rate was effectively reduced. Furthermore, the modular embedded system for information acquisition and transmission was developed. Supported by the Airflow Precision control system (APs), the rapid warning of volatile gas of flammable substances was realized. Experiments showed that RAs has satisfied selectivity to volatiles of usual flammable liquid, such as the output voltage reaches 3 V (0 - 3.3 V). With simulation about the actual installation state in bus, MWs sounds an alarm at 2 minutes after splashing 50 mL 92# petrol to the floor. For the last two years, FEVMEW has been integrated into more than 4000 buses in Hefei. This design has been proved feasible according to the actual operation. </div>
文摘Wireless Sensor Network based on ZigBee technology is a wireless network which is composed of many nodes of ZigBee RF chips, sensors and MCUs, especially suitable for application of the remote monitoring system in flammable and explosive environments. This paper presents the characteristics and advantages of ZigBee technology, also discusses the system for hardware and software design. This system effectively fulfills the remote monitoring in flammable and explosive environments and posses high practical values.
