A liquid-solid circulating fluidized bed boiler is designed and built for visualization research by applying the fluidized bed heat transfer and fouling prevention technology to the water side of the boiler. Four type...A liquid-solid circulating fluidized bed boiler is designed and built for visualization research by applying the fluidized bed heat transfer and fouling prevention technology to the water side of the boiler. Four types of engineering plastic particles with different physical properties are selected as the solid working media. The effect of particle types on the fluidization and distribution of particles in the boiler is investigated under different feedwater flow rates and amount of added particles by using the charge couple device image measurement and acquisition system. The results show that all kinds of particles can't be normally fluidized and accumulate in the drum at low amount of added particles and feedwater flow rate. The particles with great density and low sphericity are more likely to accumulate. The average solid holdup in the riser tubes increases with the increase in feedwater flow rate and the amount of added particles. The non-uniform degree of particle distribution in the riser tubes generally decreases with the increase in feedwater flow rate and the amount of added particles. The particles with small density and settling velocity have high average solid holdup in the riser tubes under close sphericity. In generally,the smaller the density and settling velocity, the more uniform the particle distribution in the riser tubes.Three-dimensional diagrams of the non-uniform degree of particle distribution in the riser tubes of the boiler are established.展开更多
The applications of fly ash and slag from circulating fluidized bed boiler were studied as mineral admixture and aggregate for steel reinforced concrete beam.The results show that the concrete beam with fly ash and sl...The applications of fly ash and slag from circulating fluidized bed boiler were studied as mineral admixture and aggregate for steel reinforced concrete beam.The results show that the concrete beam with fly ash and slag from circulating fluidized bed boilers has a similar ultimate cracking load coefficient as the ordinary cement concrete and a higher bending moment limit.Under the same load,it has a smaller deformation than the ordinary concrete.展开更多
An improved mathematical model for a circulating fluidized bed (CFB) boiler based on the model developed earlier by the authors was applied to simulate the operation of a 12 MW CFB boiler. The influences of the excess...An improved mathematical model for a circulating fluidized bed (CFB) boiler based on the model developed earlier by the authors was applied to simulate the operation of a 12 MW CFB boiler. The influences of the excess air ratio, primary air ratio, coal particle size distribution, coal properties (ash content and volatile content) and Ca/S ratio on the boiler operation were analyzed. The results showed that the model simulation may be applied to the optimum design and economic operation of the CFB boiler.展开更多
Recently, a large amount of circulating fluidized bed boiler ash (CFBA) and desulfurization gypsum (DSG) has been produced, and it is essential to develop technology to utilize them. These materials have CaO and SO<...Recently, a large amount of circulating fluidized bed boiler ash (CFBA) and desulfurization gypsum (DSG) has been produced, and it is essential to develop technology to utilize them. These materials have CaO and SO</span><sub><span style="font-family:Verdana;">3</span></sub><span style="font-family:Verdana;">, which </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">are</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> considered to be a stimulant for blast furnace slag (BFS). This study presents an experimental investigation of the compressive strength and heavy metal ions immobilization properties of cement-free materials comprising CFBA, BFS, and DSG. The feasibility of manufacturing foamed concrete using these materials was examined, and field test of foamed concrete was conducted. Experimentally, the flow, compressive strength, and heavy metal ions concentration were evaluated via inductively coupled plasma atomic emission spectroscopy (ICP</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">AES) of the paste and foamed concrete. The experimental investigation revealed the self-healing hardening ability of fluidized bed boiler ash. In addition, the compressive strength was increased with the increasing replacement rates of BFS and DSG in the CFBA paste, and the compressive strength of 14.6</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> - </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">17.2 MPa was recorded over 28 days of curing. From the result obtained, the feasibility of manufacturing foamed concrete with a foam volume </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">of </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">120 L, incorporating the aforementioned materials, is confirmed. It was also found that after 28 days of age, a 7.9-MPa compressive strength of the foamed concrete was attained, and heavy metal ions elution in this foamed concrete was also significantly reduced. Therefore, CFBA, BFS, and DSG could be used as a binder for the foamed concrete.展开更多
The co-combustion of low-rank coals through fluidized bed boiler(CFB)is an effective approach to enhance the level of resource utilization.To date,there has been a lack of investigation concerning the co-combustion ki...The co-combustion of low-rank coals through fluidized bed boiler(CFB)is an effective approach to enhance the level of resource utilization.To date,there has been a lack of investigation concerning the co-combustion kinetics and self-desulfurization characteristics of coal slime,coal gangue,and raw coal.In this study,we adopted multiple model-free and model-fitting methods to comparatively analyze co-combustion kinetics of blended coals on the basis of thermogravimetric data.Then,the sulfur balance and self-desulfurization of blended coals in the co-combustion were intensively investigated using a tube furnace set-up.The results reveal that in the presence of coal gangue in blended coals,the average activation energy(E_(a))falls within the range of 65.7 kJ/mol to 100.4 kJ/mol,as determined by four model-free methods.Conversely,in the absence of coal gangue,only the Flynn-Wall-Ozawa(FWO)and Friedman(FM)methods are deemed appropriate for calculating the average E_(a),yielding a value of 77.3 kJ/mol.The first order reaction model is confirmed to be reliable for analyzing the co-combustion kinetics of low-rank blended coals.Irrespective of the specific composition of the blended coal,a significant linear correlation exists between the Ea and the natural logarithm of the pre-exponential factor(lnA)within an extensive range of parameters.Moreover,the addition of coal gangue to the blended coal substantially enhances the self-desulfurization level,resulting in an increase from 25.7%to60.7%at 1073 K.The self-desulfurization efficiency exhibits a good linear relationship with both the mass ratio of coal gangue to coal slime and the molar ratio of calcium to sulfur.In a practical implementation,the optimal addition ratio of coal gangue is a trade-off between the self-desulfurization efficiency and the ignition capacity.展开更多
This study delves into the combustion behavior of various lignite types within a circulating fluidized bed boiler(CFBB),with a primary focus on the impact of different bed material sphericity ratios(0.5,0.7,and 0.9).U...This study delves into the combustion behavior of various lignite types within a circulating fluidized bed boiler(CFBB),with a primary focus on the impact of different bed material sphericity ratios(0.5,0.7,and 0.9).Utilizing bed material with a sphericity ratio of 0.9 sourced from theÇan power plant and verified through experimentation,the research reveals several key findings.Notably,furnace temperatures tended to rise with higher sphericity ratios,albeit with variations between lignite types,particularly highlighting the complexity of this relationship in the case of GLI-Tunçbilek lignite.Pressure levels in the combustion chamber remained consistent across different sphericity ratios,indicating minimal influence on pressure dynamics.Improved combustion efficiency,especially at the bottom of the boiler,was observed at lower sphericity levels(0.5 and 0.7)forÇan lignite,as reflected in CO_(2) mole fractions.While NO_(x) emissions generally decreased with lower sphericity,the sensitivity to sphericity varied by lignite type,with Ilgın lignite showcasing low NO_(x) but high SO_(2) emissions,underscoring the intricate interplay between lignite properties,sphericity,and emissions.Overall,this study advances our understanding of CFBB combustion dynamics,offering insights valuable for optimizing performance and emissions control,particularly in lignite-based power.展开更多
A new Kind of measuring method that may be used to measure high temperature circulating solid particles flux in a circulating fluidized bed boiler is studied in this paper. The measuring method is founded on the princ...A new Kind of measuring method that may be used to measure high temperature circulating solid particles flux in a circulating fluidized bed boiler is studied in this paper. The measuring method is founded on the principle of thermal equilibrium. A series of cold tests and hot tests were carried to optimize the structure and collocation of water-cooling tubes and showed that the method had the advantage of simple, accurate, reliable and good applicability for on-line "usage in a circulating fluidized bed boiler.展开更多
This paper presents a set of general dynamic mathematical models for the combustion system of acirculating fluidized bi-bed boiler. The models fully consider the flow, combustion and heat transfercharacteristics, and ...This paper presents a set of general dynamic mathematical models for the combustion system of acirculating fluidized bi-bed boiler. The models fully consider the flow, combustion and heat transfercharacteristics, and describe the physical and chemical processes inside the bi-bed, including the gassolid flow, multiple particles combustion, gas chemical reactions, heat transfer and pressure balances,etc.展开更多
In order to solve transport problems of industry solid,firstly,a new applicationnotion of pipeline transport was presented,that is to say,combining pretreatment andtransport with disposal techniques of industry solid ...In order to solve transport problems of industry solid,firstly,a new applicationnotion of pipeline transport was presented,that is to say,combining pretreatment andtransport with disposal techniques of industry solid waste.Secondly,the integrated dis-posal and transport system for industry solid waste was introduced,in particular,the oper-ating principles,equipment set-up,key technology and technical parameters.Next,thispaper illustrated the application of this integrated system.Such as it can transport coalsludge with sufficiently high solids content(about 72%～77%)and high apparent viscosity(about 1 000～3 000 Pa.s)directly by pipeline having no use for water and addition agent.Generally,the transport distance is about 1 000 m.This system has been successfullyused in innocuous disposition and efficient utilization of other industrial byproducts or solidwastes,such as city sludge and paper making waste.The integrated system causes nopollution to the environment for its complete seal and realizes protecting the environment,conserving the energy,promoting the development of cycling economic.Finally,the paperdiscussed the research works that were needed for studying such pipeline transport sys-tem and narrates the relevant condition and application status.展开更多
This paper reviews the researches on boiler combustion optimization,which is an important direction in the field of energy saving and emission reduction.Many methods have been used to deal with boiler combustion optim...This paper reviews the researches on boiler combustion optimization,which is an important direction in the field of energy saving and emission reduction.Many methods have been used to deal with boiler combustion optimization,among which evolutionary computing(EC)techniques have recently gained much attention.However,the existing researches are not sufficiently focused and have not been summarized systematically.This has led to slow progress of research on boiler combustion optimization and has obstacles in the application.This paper introduces a comprehensive survey of the works of intelligent optimization algorithms in boiler combustion optimization and summarizes the contributions of different optimization algorithms.Finally,this paper discusses new research challenges and outlines future research directions,which can guide boiler combustion optimization to improve energy efficiency and reduce pollutant emission concentrations.展开更多
Recently, EMMS-based models are being widely applied in simulations of high-throughput circulating fluidized beds （CFBs） with fine particles. Its use for low flux systems, such as CFB boiler （CFBB）, still remains ...Recently, EMMS-based models are being widely applied in simulations of high-throughput circulating fluidized beds （CFBs） with fine particles. Its use for low flux systems, such as CFB boiler （CFBB）, still remains unexplored. In this work, it has been found that the original definition of cluster diameter in EMMS model is unsuitable for simulations of the CFB boiler with low solids flux. To remedy this, we propose a new model of cluster diameter. The EMMS-based drag model （EMMS/matrix model） with this revised cluster definition is validated through the computational fluid dynamics （CFD） simulation of a CFB boiler.展开更多
A Bayesian-Gaussian Neural Network (BGNN) is put forward in this paper to predict the static and transient performance of Circulating Fluidized Bed (CFB) boilers. The advantages of this network over Back-Propagation N...A Bayesian-Gaussian Neural Network (BGNN) is put forward in this paper to predict the static and transient performance of Circulating Fluidized Bed (CFB) boilers. The advantages of this network over Back-Propagation Neural Networks (BPNNs), easier determination of topology, simpler and time saving in training process as well as selforganizing ability, make this network more practical in on-line performance prediction for complicated processes. Simulation shows that this network is comparable to the BPNNs in predicting the performance of CFB boilers. Good and practical on-line performance predictions are essential for operation guide and model predictive control of CFB boiIers, which are under research by the authors.展开更多
基金supported by the open foundation of State Key Laboratory of Chemical Engineering (SKL–ChE–18B03)the Municipal Science and Technology Commission of Tianjin, China (2009ZCKFGX01900)。
文摘A liquid-solid circulating fluidized bed boiler is designed and built for visualization research by applying the fluidized bed heat transfer and fouling prevention technology to the water side of the boiler. Four types of engineering plastic particles with different physical properties are selected as the solid working media. The effect of particle types on the fluidization and distribution of particles in the boiler is investigated under different feedwater flow rates and amount of added particles by using the charge couple device image measurement and acquisition system. The results show that all kinds of particles can't be normally fluidized and accumulate in the drum at low amount of added particles and feedwater flow rate. The particles with great density and low sphericity are more likely to accumulate. The average solid holdup in the riser tubes increases with the increase in feedwater flow rate and the amount of added particles. The non-uniform degree of particle distribution in the riser tubes generally decreases with the increase in feedwater flow rate and the amount of added particles. The particles with small density and settling velocity have high average solid holdup in the riser tubes under close sphericity. In generally,the smaller the density and settling velocity, the more uniform the particle distribution in the riser tubes.Three-dimensional diagrams of the non-uniform degree of particle distribution in the riser tubes of the boiler are established.
基金Funded by the Foundation of Scientific and Technological Project of Heilongjiang Province,China (GB01A3022)
文摘The applications of fly ash and slag from circulating fluidized bed boiler were studied as mineral admixture and aggregate for steel reinforced concrete beam.The results show that the concrete beam with fly ash and slag from circulating fluidized bed boilers has a similar ultimate cracking load coefficient as the ordinary cement concrete and a higher bending moment limit.Under the same load,it has a smaller deformation than the ordinary concrete.
文摘An improved mathematical model for a circulating fluidized bed (CFB) boiler based on the model developed earlier by the authors was applied to simulate the operation of a 12 MW CFB boiler. The influences of the excess air ratio, primary air ratio, coal particle size distribution, coal properties (ash content and volatile content) and Ca/S ratio on the boiler operation were analyzed. The results showed that the model simulation may be applied to the optimum design and economic operation of the CFB boiler.
文摘Recently, a large amount of circulating fluidized bed boiler ash (CFBA) and desulfurization gypsum (DSG) has been produced, and it is essential to develop technology to utilize them. These materials have CaO and SO</span><sub><span style="font-family:Verdana;">3</span></sub><span style="font-family:Verdana;">, which </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">are</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> considered to be a stimulant for blast furnace slag (BFS). This study presents an experimental investigation of the compressive strength and heavy metal ions immobilization properties of cement-free materials comprising CFBA, BFS, and DSG. The feasibility of manufacturing foamed concrete using these materials was examined, and field test of foamed concrete was conducted. Experimentally, the flow, compressive strength, and heavy metal ions concentration were evaluated via inductively coupled plasma atomic emission spectroscopy (ICP</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">AES) of the paste and foamed concrete. The experimental investigation revealed the self-healing hardening ability of fluidized bed boiler ash. In addition, the compressive strength was increased with the increasing replacement rates of BFS and DSG in the CFBA paste, and the compressive strength of 14.6</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> - </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">17.2 MPa was recorded over 28 days of curing. From the result obtained, the feasibility of manufacturing foamed concrete with a foam volume </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">of </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">120 L, incorporating the aforementioned materials, is confirmed. It was also found that after 28 days of age, a 7.9-MPa compressive strength of the foamed concrete was attained, and heavy metal ions elution in this foamed concrete was also significantly reduced. Therefore, CFBA, BFS, and DSG could be used as a binder for the foamed concrete.
基金supported by the National Natural Science Foundation of China(52276110)。
文摘The co-combustion of low-rank coals through fluidized bed boiler(CFB)is an effective approach to enhance the level of resource utilization.To date,there has been a lack of investigation concerning the co-combustion kinetics and self-desulfurization characteristics of coal slime,coal gangue,and raw coal.In this study,we adopted multiple model-free and model-fitting methods to comparatively analyze co-combustion kinetics of blended coals on the basis of thermogravimetric data.Then,the sulfur balance and self-desulfurization of blended coals in the co-combustion were intensively investigated using a tube furnace set-up.The results reveal that in the presence of coal gangue in blended coals,the average activation energy(E_(a))falls within the range of 65.7 kJ/mol to 100.4 kJ/mol,as determined by four model-free methods.Conversely,in the absence of coal gangue,only the Flynn-Wall-Ozawa(FWO)and Friedman(FM)methods are deemed appropriate for calculating the average E_(a),yielding a value of 77.3 kJ/mol.The first order reaction model is confirmed to be reliable for analyzing the co-combustion kinetics of low-rank blended coals.Irrespective of the specific composition of the blended coal,a significant linear correlation exists between the Ea and the natural logarithm of the pre-exponential factor(lnA)within an extensive range of parameters.Moreover,the addition of coal gangue to the blended coal substantially enhances the self-desulfurization level,resulting in an increase from 25.7%to60.7%at 1073 K.The self-desulfurization efficiency exhibits a good linear relationship with both the mass ratio of coal gangue to coal slime and the molar ratio of calcium to sulfur.In a practical implementation,the optimal addition ratio of coal gangue is a trade-off between the self-desulfurization efficiency and the ignition capacity.
文摘This study delves into the combustion behavior of various lignite types within a circulating fluidized bed boiler(CFBB),with a primary focus on the impact of different bed material sphericity ratios(0.5,0.7,and 0.9).Utilizing bed material with a sphericity ratio of 0.9 sourced from theÇan power plant and verified through experimentation,the research reveals several key findings.Notably,furnace temperatures tended to rise with higher sphericity ratios,albeit with variations between lignite types,particularly highlighting the complexity of this relationship in the case of GLI-Tunçbilek lignite.Pressure levels in the combustion chamber remained consistent across different sphericity ratios,indicating minimal influence on pressure dynamics.Improved combustion efficiency,especially at the bottom of the boiler,was observed at lower sphericity levels(0.5 and 0.7)forÇan lignite,as reflected in CO_(2) mole fractions.While NO_(x) emissions generally decreased with lower sphericity,the sensitivity to sphericity varied by lignite type,with Ilgın lignite showcasing low NO_(x) but high SO_(2) emissions,underscoring the intricate interplay between lignite properties,sphericity,and emissions.Overall,this study advances our understanding of CFBB combustion dynamics,offering insights valuable for optimizing performance and emissions control,particularly in lignite-based power.
文摘A new Kind of measuring method that may be used to measure high temperature circulating solid particles flux in a circulating fluidized bed boiler is studied in this paper. The measuring method is founded on the principle of thermal equilibrium. A series of cold tests and hot tests were carried to optimize the structure and collocation of water-cooling tubes and showed that the method had the advantage of simple, accurate, reliable and good applicability for on-line "usage in a circulating fluidized bed boiler.
文摘This paper presents a set of general dynamic mathematical models for the combustion system of acirculating fluidized bi-bed boiler. The models fully consider the flow, combustion and heat transfercharacteristics, and describe the physical and chemical processes inside the bi-bed, including the gassolid flow, multiple particles combustion, gas chemical reactions, heat transfer and pressure balances,etc.
基金Science and Technology Corporation Innovation Fund of China(02C26211100499) PH.D Program Fund(20020290011)
文摘In order to solve transport problems of industry solid,firstly,a new applicationnotion of pipeline transport was presented,that is to say,combining pretreatment andtransport with disposal techniques of industry solid waste.Secondly,the integrated dis-posal and transport system for industry solid waste was introduced,in particular,the oper-ating principles,equipment set-up,key technology and technical parameters.Next,thispaper illustrated the application of this integrated system.Such as it can transport coalsludge with sufficiently high solids content(about 72%～77%)and high apparent viscosity(about 1 000～3 000 Pa.s)directly by pipeline having no use for water and addition agent.Generally,the transport distance is about 1 000 m.This system has been successfullyused in innocuous disposition and efficient utilization of other industrial byproducts or solidwastes,such as city sludge and paper making waste.The integrated system causes nopollution to the environment for its complete seal and realizes protecting the environment,conserving the energy,promoting the development of cycling economic.Finally,the paperdiscussed the research works that were needed for studying such pipeline transport sys-tem and narrates the relevant condition and application status.
基金supported by the National Natural Science Foundation of China(Nos.61806179,61876169,61922072,61976237,61673404,62106230,62006069,62206255,and 62203332)China Postdoctoral Science Foundation(Nos.2021T140616,2021M692920,2022M712878,and 2022TQ0298)+2 种基金Key R&D Projects of Ministry of Science and Technology(No.2022YFD2001200)Key R&D and Promotion Projects in Henan Province(Nos.192102210098 and 212102210510)Henan Postdoctoral Foundation(No.202003019).
文摘This paper reviews the researches on boiler combustion optimization,which is an important direction in the field of energy saving and emission reduction.Many methods have been used to deal with boiler combustion optimization,among which evolutionary computing(EC)techniques have recently gained much attention.However,the existing researches are not sufficiently focused and have not been summarized systematically.This has led to slow progress of research on boiler combustion optimization and has obstacles in the application.This paper introduces a comprehensive survey of the works of intelligent optimization algorithms in boiler combustion optimization and summarizes the contributions of different optimization algorithms.Finally,this paper discusses new research challenges and outlines future research directions,which can guide boiler combustion optimization to improve energy efficiency and reduce pollutant emission concentrations.
基金supported by the Natural Science Foundation of China under Grant Nos. 21106157,21176240 and 51106168Ministry of Science & Technology (MOST) under Grant No. 2007AA050302-03the "Strategic Priority Research Program" of Chinese Academy of Sciences under Grant Nos. KGCX2-YW-222 and XDA07080202
文摘Recently, EMMS-based models are being widely applied in simulations of high-throughput circulating fluidized beds （CFBs） with fine particles. Its use for low flux systems, such as CFB boiler （CFBB）, still remains unexplored. In this work, it has been found that the original definition of cluster diameter in EMMS model is unsuitable for simulations of the CFB boiler with low solids flux. To remedy this, we propose a new model of cluster diameter. The EMMS-based drag model （EMMS/matrix model） with this revised cluster definition is validated through the computational fluid dynamics （CFD） simulation of a CFB boiler.
文摘A Bayesian-Gaussian Neural Network (BGNN) is put forward in this paper to predict the static and transient performance of Circulating Fluidized Bed (CFB) boilers. The advantages of this network over Back-Propagation Neural Networks (BPNNs), easier determination of topology, simpler and time saving in training process as well as selforganizing ability, make this network more practical in on-line performance prediction for complicated processes. Simulation shows that this network is comparable to the BPNNs in predicting the performance of CFB boilers. Good and practical on-line performance predictions are essential for operation guide and model predictive control of CFB boiIers, which are under research by the authors.
