Detecting holes in oil–gas reservoirs is vital to the evaluation of reservoir potential. The main objective of this study is to demonstrate the feasibility of identifying general micro-hole shapes, including triangul...Detecting holes in oil–gas reservoirs is vital to the evaluation of reservoir potential. The main objective of this study is to demonstrate the feasibility of identifying general micro-hole shapes, including triangular, circular, and square shapes, in oil–gas reservoirs by adopting terahertz time-domain spectroscopy(THz-TDS). We evaluate the THz absorption responses of punched silicon(Si) wafers having micro-holes with sizes of 20 μm–500 μm. Principal component analysis(PCA) is used to establish a model between THz absorbance and hole shapes. The positions of samples in three-dimensional spaces for three principal components are used to determine the differences among diverse hole shapes and the homogeneity of similar shapes. In addition, a new Si wafer with the unknown hole shapes, including triangular, circular, and square, can be qualitatively identified by combining THz-TDS and PCA. Therefore, the combination of THz-TDS with mathematical statistical methods can serve as an effective approach to the rapid identification of micro-hole shapes in oil–gas reservoirs.展开更多
Accurate boundary conditions of composite material plates with different holes are founded to settle boundary condition problems of complex holes by conformal mapping method upon the nonhomogeneous anisotropic elastic...Accurate boundary conditions of composite material plates with different holes are founded to settle boundary condition problems of complex holes by conformal mapping method upon the nonhomogeneous anisotropic elastic and complex function theory. And then the two stress functions required were founded on Cauchy integral by boundary conditions. The final stress distributions of opening structure and the analytical solution on composite material plate with rectangle hole and wing manholes were achieved. The influences on hole-edge stress concentration factors are discussed under different loads and fiber direction cases, and then contrast calculates are carried through FEM.展开更多
The strength of composite plate with different hole-shapes is always one of the most important but complicated issues in the application of the composite material. The holes will lead to mutations and discontinuity to...The strength of composite plate with different hole-shapes is always one of the most important but complicated issues in the application of the composite material. The holes will lead to mutations and discontinuity to the structure. So the hole-edge stress concentration is always a serious phenomenon. And the phenomenon makes the structure strength decrease very quickly to form dangerous weak points. Most partial damage begins from these weak points. According to the complex variable functions theory, the accurate boundary condition of composite plate with different hole-shapes is founded by conformal mapping method to settle the boundary condition problem of complex hole-shapes. Composite plate with commonly hole-shapes in engineering is studied by several complex variable stress fimction. The boundary integral equations are founded based on exact boundary conditions. Then the exact hole-edge stress analytic solution of composite plate with rectangle holes and wing manholes is resolved. Both of offset axis loadings and its influences on the stress concentration coefficient of the hole-edge are discussed. And comparisons of different loads along various offset axis on the hole-edge stress distribution of orthotropic plate with rectangle hole or wing manhole are made. It can be concluded that hole-edge with continuous variable curvatures might help to decrease the stress concentration coefficient; and smaller angle of outer load and fiber can decrease the stress peak value.展开更多
We study the thermoelectric field for an electrically and thermally insulated coated hole of arbitrary shape embedded in an infinite nonlinearly coupled thermoelectric material subject to uniform remote electric curre...We study the thermoelectric field for an electrically and thermally insulated coated hole of arbitrary shape embedded in an infinite nonlinearly coupled thermoelectric material subject to uniform remote electric current density and uniform remote energy flux.A conformal mapping function for the coating and matrix is introduced,which simultaneously maps the hole boundary and the coating-matrix interface onto two concentric circles in the image plane.Using analytic continuation,we derive a general solution in terms of two auxiliary functions.The general solution satisfies the insulating conditions along the hole boundary and all of the continuity conditions across the perfect coating-matrix interface.Once the two auxiliary functions have been obtained in the elementary-form,the four original analytic functions in the coating and matrix characterizing the thermoelectric fields are completely and explicitly determined.The design of a neutral coated circular hole that does not disturb the prescribed thermoelectric field in the thermoelectric matrix is achieved when the relative thickness parameter and the two mismatch parameters satisfy a simple condition.Finally,the neutrality of a coated circular thermoelectric inhomogeneity is also accomplished.展开更多
To improve the cooling performance, shape optimization of a laidback fan-shaped film cooling hole was performed. Three geometric parameters, including hole length, lateral expansion angle and forward expansion angle, ...To improve the cooling performance, shape optimization of a laidback fan-shaped film cooling hole was performed. Three geometric parameters, including hole length, lateral expansion angle and forward expansion angle, were selected as the design parameters. Numerical model of the film cooling system was established, validated, and used to generate 32 groups of training samples. Least square support vector machine(LS-SVM) was applied for surrogate model, and the optimal design parameters were determined by a kind of chaotic optimization algorithm. As hole length, lateral expansion angle and forward expansion angle are 90 mm, 20° and 5°, the area-averaged film cooling effectiveness can reach its maximum value in the design space. LS-SVM coupled with chaotic optimization algorithm is a promising scheme for the optimization of shaped film cooling holes.展开更多
Film cooling is introduction of a secondary fluid （coolant or injected fluid） at one or more discrete locations along a surface exposed to a high temperature environment to protect that surface not only in the immed...Film cooling is introduction of a secondary fluid （coolant or injected fluid） at one or more discrete locations along a surface exposed to a high temperature environment to protect that surface not only in the immediate region of injection but also downstream region. This paper numerically investigated the film cooling effectiveness on two types of hole geometries which are cut-shaped hole and antivortex hole. The 3D computational geometries are modeled with a single 30 deg angled hole on a flat surface. The different blowing ratios of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5,5 and k-Epsilon turbulence model are used in this study. A two dimensional distribution of film cooling effectiveness in the downstream region of the cooling hole is performed. A comparison of spanwise averaged effectiveness is also performed in the field starts from center point of hole to X/D=-30.展开更多
In this paper, the basic formulae for the semi-analytical graded FEM on FGM members are derived. Since FGM parameters vary along three space coordinates, the parameters can be integrated in mechanical equations. There...In this paper, the basic formulae for the semi-analytical graded FEM on FGM members are derived. Since FGM parameters vary along three space coordinates, the parameters can be integrated in mechanical equations. Therefore with the parameters of a given FGM plate, problems of FGM plate under various conditions can be solved. The approach uses 1D discretization to obtain 3D solutions, which is proven to be an effective numerical method for the mechanical analyses of FGM structures. Examples of FGM plates with complex shapes and various holes are presented.展开更多
Hybrid RANS-LES methods offer a means of reducing computational cost and setup time to simulate transitional flows. Several methods are evaluated in ANSYS CFX, including Scale-Adaptive Simulation (SAS), Shielded Detac...Hybrid RANS-LES methods offer a means of reducing computational cost and setup time to simulate transitional flows. Several methods are evaluated in ANSYS CFX, including Scale-Adaptive Simulation (SAS), Shielded Detached Eddy Simulation (SDES), Stress-Blended Eddy Simulation (SBES), and Zonal Large Eddy Simulation (ZLES), along with a no-model laminar simulation. Each is used to simulate an adiabatic flat plate film cooling experiment of a shaped hole at low Reynolds number. Adiabatic effectiveness is calculated for Blowing Ratio (BR) = 1.5 and Density Ratio (DR) = 1.5. The ZLES method and laminar simulation most accurately match experimental lateral-average adiabatic effectiveness along the streamwise direction from the trailing edge of the hole to 35 hole diameters downstream of the hole (X/D = 0 to X/D = 35), with RMS deviations of 5.1% and 4.2%, and maximum deviations of 8% and 11%, respectively. The accuracy of these models is attributed to the resolution of turbulent structures in not only the mixing region but in the upstream boundary layer as well, where the other methods utilize RANS and do not switch to LES.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.61405259)the National Basic Research Program of China(Grant No.2014CB744302)the Specially Founded Program on National Key Scientific Instruments and Equipment Development,China(Grant No.2012YQ140005)
文摘Detecting holes in oil–gas reservoirs is vital to the evaluation of reservoir potential. The main objective of this study is to demonstrate the feasibility of identifying general micro-hole shapes, including triangular, circular, and square shapes, in oil–gas reservoirs by adopting terahertz time-domain spectroscopy(THz-TDS). We evaluate the THz absorption responses of punched silicon(Si) wafers having micro-holes with sizes of 20 μm–500 μm. Principal component analysis(PCA) is used to establish a model between THz absorbance and hole shapes. The positions of samples in three-dimensional spaces for three principal components are used to determine the differences among diverse hole shapes and the homogeneity of similar shapes. In addition, a new Si wafer with the unknown hole shapes, including triangular, circular, and square, can be qualitatively identified by combining THz-TDS and PCA. Therefore, the combination of THz-TDS with mathematical statistical methods can serve as an effective approach to the rapid identification of micro-hole shapes in oil–gas reservoirs.
基金This project is supported by National Natural Science Foundation of China(No.50175031).
文摘Accurate boundary conditions of composite material plates with different holes are founded to settle boundary condition problems of complex holes by conformal mapping method upon the nonhomogeneous anisotropic elastic and complex function theory. And then the two stress functions required were founded on Cauchy integral by boundary conditions. The final stress distributions of opening structure and the analytical solution on composite material plate with rectangle hole and wing manholes were achieved. The influences on hole-edge stress concentration factors are discussed under different loads and fiber direction cases, and then contrast calculates are carried through FEM.
基金supported by National Natural Science Foundation of China(No.50675209)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,Ministry of Education of China(No.200724).
文摘The strength of composite plate with different hole-shapes is always one of the most important but complicated issues in the application of the composite material. The holes will lead to mutations and discontinuity to the structure. So the hole-edge stress concentration is always a serious phenomenon. And the phenomenon makes the structure strength decrease very quickly to form dangerous weak points. Most partial damage begins from these weak points. According to the complex variable functions theory, the accurate boundary condition of composite plate with different hole-shapes is founded by conformal mapping method to settle the boundary condition problem of complex hole-shapes. Composite plate with commonly hole-shapes in engineering is studied by several complex variable stress fimction. The boundary integral equations are founded based on exact boundary conditions. Then the exact hole-edge stress analytic solution of composite plate with rectangle holes and wing manholes is resolved. Both of offset axis loadings and its influences on the stress concentration coefficient of the hole-edge are discussed. And comparisons of different loads along various offset axis on the hole-edge stress distribution of orthotropic plate with rectangle hole or wing manhole are made. It can be concluded that hole-edge with continuous variable curvatures might help to decrease the stress concentration coefficient; and smaller angle of outer load and fiber can decrease the stress peak value.
基金supported by the Discovery Grant from the Natural Sciences and Engineering Research Council of Canada(No.RGPIN-2017-03716115112)。
文摘We study the thermoelectric field for an electrically and thermally insulated coated hole of arbitrary shape embedded in an infinite nonlinearly coupled thermoelectric material subject to uniform remote electric current density and uniform remote energy flux.A conformal mapping function for the coating and matrix is introduced,which simultaneously maps the hole boundary and the coating-matrix interface onto two concentric circles in the image plane.Using analytic continuation,we derive a general solution in terms of two auxiliary functions.The general solution satisfies the insulating conditions along the hole boundary and all of the continuity conditions across the perfect coating-matrix interface.Once the two auxiliary functions have been obtained in the elementary-form,the four original analytic functions in the coating and matrix characterizing the thermoelectric fields are completely and explicitly determined.The design of a neutral coated circular hole that does not disturb the prescribed thermoelectric field in the thermoelectric matrix is achieved when the relative thickness parameter and the two mismatch parameters satisfy a simple condition.Finally,the neutrality of a coated circular thermoelectric inhomogeneity is also accomplished.
基金Project(U1508212)supported by the National Natural Science Foundation of ChinaProject(2015M570448)supported by the Postdoctoral Science Foundation of China
文摘To improve the cooling performance, shape optimization of a laidback fan-shaped film cooling hole was performed. Three geometric parameters, including hole length, lateral expansion angle and forward expansion angle, were selected as the design parameters. Numerical model of the film cooling system was established, validated, and used to generate 32 groups of training samples. Least square support vector machine(LS-SVM) was applied for surrogate model, and the optimal design parameters were determined by a kind of chaotic optimization algorithm. As hole length, lateral expansion angle and forward expansion angle are 90 mm, 20° and 5°, the area-averaged film cooling effectiveness can reach its maximum value in the design space. LS-SVM coupled with chaotic optimization algorithm is a promising scheme for the optimization of shaped film cooling holes.
文摘Film cooling is introduction of a secondary fluid （coolant or injected fluid） at one or more discrete locations along a surface exposed to a high temperature environment to protect that surface not only in the immediate region of injection but also downstream region. This paper numerically investigated the film cooling effectiveness on two types of hole geometries which are cut-shaped hole and antivortex hole. The 3D computational geometries are modeled with a single 30 deg angled hole on a flat surface. The different blowing ratios of 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5,5 and k-Epsilon turbulence model are used in this study. A two dimensional distribution of film cooling effectiveness in the downstream region of the cooling hole is performed. A comparison of spanwise averaged effectiveness is also performed in the field starts from center point of hole to X/D=-30.
基金Project supported by the National Natural Science Foundation of China (No. 10432030)
文摘In this paper, the basic formulae for the semi-analytical graded FEM on FGM members are derived. Since FGM parameters vary along three space coordinates, the parameters can be integrated in mechanical equations. Therefore with the parameters of a given FGM plate, problems of FGM plate under various conditions can be solved. The approach uses 1D discretization to obtain 3D solutions, which is proven to be an effective numerical method for the mechanical analyses of FGM structures. Examples of FGM plates with complex shapes and various holes are presented.
文摘Hybrid RANS-LES methods offer a means of reducing computational cost and setup time to simulate transitional flows. Several methods are evaluated in ANSYS CFX, including Scale-Adaptive Simulation (SAS), Shielded Detached Eddy Simulation (SDES), Stress-Blended Eddy Simulation (SBES), and Zonal Large Eddy Simulation (ZLES), along with a no-model laminar simulation. Each is used to simulate an adiabatic flat plate film cooling experiment of a shaped hole at low Reynolds number. Adiabatic effectiveness is calculated for Blowing Ratio (BR) = 1.5 and Density Ratio (DR) = 1.5. The ZLES method and laminar simulation most accurately match experimental lateral-average adiabatic effectiveness along the streamwise direction from the trailing edge of the hole to 35 hole diameters downstream of the hole (X/D = 0 to X/D = 35), with RMS deviations of 5.1% and 4.2%, and maximum deviations of 8% and 11%, respectively. The accuracy of these models is attributed to the resolution of turbulent structures in not only the mixing region but in the upstream boundary layer as well, where the other methods utilize RANS and do not switch to LES.
