Monitoring shear deformation of sliding zones is of great significance for understanding the landslide evolution mechanism,in which fiber optic strain sensing has shown great potential.However,the cor-relation between...Monitoring shear deformation of sliding zones is of great significance for understanding the landslide evolution mechanism,in which fiber optic strain sensing has shown great potential.However,the cor-relation between strain measurements of quasi-distributed fiber Bragg grating(FBG)sensing arrays and shear displacements of surrounding soil remains elusive.In this study,a direct shear model test was conducted to simulate the shear deformation of sliding zones,in which the soil internal deformation was captured using FBG strain sensors and the soil surface deformation was measured by particle image velocimetry(PIV).The test results show that there were two main slip surfaces and two secondary ones,developing a spindle-shaped shear band in the soil.The formation of the shear band was successfully captured by FBG sensors.A sinusoidal model was proposed to describe the fiber optic cable deformation behavior.On this basis,the shear displacements and shear band widths were calculated by using strain measurements.This work provides important insight into the deduction of soil shear deformation using soil-embedded FBG strain sensors.展开更多
Aim To investigate the spray particle velocity and its distribution characteristics. Methods\ A set of PIV (particle image velocimetry) system was developed and used to observe and analyze the spray particle velocity...Aim To investigate the spray particle velocity and its distribution characteristics. Methods\ A set of PIV (particle image velocimetry) system was developed and used to observe and analyze the spray particle velocity field. Results and Conclusion\ Double exposure image of the spray particle within the region of 10-50 mm from the nozzle tip was recorded and analyzed by the IBAS2000 analysis system. Some characteristics of the spray particle velocity and its distribution were obtained.展开更多
A special transparent centrifugal pump is designed. Detailed opticalmeasurements of the flow inside the rotating passages of a five-bladed shroud centrifugal pumpimpeller have been performed by using two-dimensional p...A special transparent centrifugal pump is designed. Detailed opticalmeasurements of the flow inside the rotating passages of a five-bladed shroud centrifugal pumpimpeller have been performed by using two-dimensional particle image velocimetry (PIV). The flow issurveyed at three load conditions q_V/q_(Vd) = 0.4, q_V/q_(Vd) = 1.0, q_V/q_(Vd) = 1.5,respectively. As a result, phase averaged PIV velocity vector maps on three planes between hub andshroud of the impeller are presented. At design load, the mean field of relative velocity ispredominantly vane congruent, showing well-behaved flow without separation. The distributions of therelative velocity on different plane along the pump shaft are very different and there is always alow velocity zone near the pressure-side of the blade at both low and design flow rate, but thelow-velocity-zone at the low flow rate is much larger than that at the design one. The studydemonstrates that the PIV technique is efficient in providing reliable and detailed velocity dataover a full impeller passage.展开更多
Large-view flow field measurements using the particle image velocimetry （PIV） technique with high resolution CCD cameras on a rotating 1/8 scale blade model of the NREL UAE phase VI wind turbine are conducted in the...Large-view flow field measurements using the particle image velocimetry （PIV） technique with high resolution CCD cameras on a rotating 1/8 scale blade model of the NREL UAE phase VI wind turbine are conducted in the engineering-oriented q53.2 m wind tunnel. The motivation is to establish the database of the initiation and development of the tip vortex to study the flow structure and mechanism of the wind turbine. The results show that the tip vortex first moves inward for a very short period and then moves outward with the wake expansion, while its vorticity decreases with time after being trailed from the trailing edge of the blade tip, and then increases continuously with the rapid rolling-up to form a strong tip vortex. The measurements also indicate that the downstream movement of the tip vortex is nearly linear in the very near wake under the test condition.展开更多
A new small-scale geotechnical physical model in 1-g and unconfined condition, combining the transparent soil, close-range photogrammetry and particle image velocimetry(PIV), was employed, which provides a non-intrusi...A new small-scale geotechnical physical model in 1-g and unconfined condition, combining the transparent soil, close-range photogrammetry and particle image velocimetry(PIV), was employed, which provides a non-intrusively internal deformation measurement approach to monitor the internal deformation of soil caused by expanded-base pile jacking with casing. The transparent soil was made of fused quartz and its refractive index matched blended oil, adding reflective particles(glass beads). Closerange photogrammetry was employed to record the images of the process of casing jacking and extraction in transparent soil, allowing the use of Matlab-based Geo-PIV to figure out the displacement field converted from image space to object space. Analysis of test results indicates that the maximum displacement caused by casing jacking for expandedconical-base pile is decreased by 29% compared with that for expanded-flat-base pile. The main movement happens at the early stage of casing extraction. The maximum displacement caused by casing extraction for the conical base is about 43% of that for the flatbase, while the affected zone caused by casing extraction for the conical base accounts for about 1/3 of that for the flat base. The contraction for horizontal displacements tends to decrease with the depth increasing. By contrast, the contraction under pile base decreases with the increasing of displacement. The displacements generated by jacking a conventional pile having a diameter equal to the casing diameter of the expanded-base pile were comparable to the net displacement taking place due to expanded-base pile installation for the conical base pile.展开更多
The failure of a drilling pump is always due to the break of the drilling pump valve, which is one of the most important but also the weakest parts of the drilling pump. Over the decades, the degradation of drilling p...The failure of a drilling pump is always due to the break of the drilling pump valve, which is one of the most important but also the weakest parts of the drilling pump. Over the decades, the degradation of drilling pump valves has been investigated extensively and various failure mechanisms have been proposed. However, no experimental test on the fluid has been successfully performed to support some of these mechanisms. In this paper, tests of the flow within the valve play are carried out to investigate the factors resulting in the failure of the valve. In the tests, particle image velocimetry（PIV） technology is employed to measure the flow field distribution of the valve play in the model. From these tests, the distributions of velocity and vorticity of fluid in ＇various valves with different valve angles and different valve lifts are obtained, from which the features of flow fields are derived and generalized. Subsequently, a general rule of the influence of valve angles and valve lifts on the flow velocity is concluded according to chart analyses of maximal velocities and mean velocities. Finally, an analysis is made on the possibility of valve failure caused by erosion and abrasion in a working valve, with the application of the failure mechanisms of drilling pump valves. PIV measurement improves the study on the failure of the drilling pump valve, and the results show good agreement with previous computational fluid dynamics（CFD） simulations.展开更多
This article reports a particle image velocimetry study and the comparative results of a numerical simulation into the hydrodynamic characteristics around an artificial reef.We reveal the process of flow separation an...This article reports a particle image velocimetry study and the comparative results of a numerical simulation into the hydrodynamic characteristics around an artificial reef.We reveal the process of flow separation and vortex evolution,and compare the force terms generated by our artificial reef model.The numerical simulation agrees well with experimental results,showing the applicability of computational fluid dynamics to the hydrodynamics of an artificial reef.Furthermore,we numerically simulate the hydrodynamics of the reef model for seven velocities.The results show that the drag coefficient is approximately 1.21 in a self-modeling region for Reynolds numbers between 2.123×104and 9×104.Therefore,the upwelling height and current width of the flow field do not change significantly when the inflow velocity increases.Our study indicates that computational fluid dynamics can be applied to study the hydrodynamics of an artificial reef and offer clues to its construction.展开更多
The double blade pump is widely used in sewage treatment industry,however,the research on the internal flow characteristics of the double blade pump with particle image velocimetry（PIV） technology is very little at ...The double blade pump is widely used in sewage treatment industry,however,the research on the internal flow characteristics of the double blade pump with particle image velocimetry（PIV） technology is very little at present.To reveal inner flow characteristics in double blade pump impeller under off-design and design conditions,inner flows in a double blade pump impeller,whose specific speed is 111,are measured under the five off-design conditions and design condition by using 3D PIV test technology.In order to ensure the accuracy of the 3D PIV test,the external trigger synchronization system which makes use of fiber optic and equivalent calibration method are applied.The 3D PIV relative velocity synthesis procedure is compiled by using Visual C＋＋ 2005.Then absolute velocity distribution and relative velocity distribution in the double blade pump impeller are obtained.Test results show that vortex exists in each condition,but the location,size and velocity of vortex core are different.Average absolute velocity value of impeller outlet increases at first,then decreases,and then increases again with increase of flow rate.Again average relative velocity values under 0.4,0.8,and 1.2 design condition are higher than that under 1.0 design condition,while under 0.6 and 1.4 design condition it is lower.Under low flow rate conditions,radial vectors of absolute velocities at impeller outlet and blade inlet near the pump shaft decrease with increase of flow rate,while that of relative velocities at the suction side near the pump shaft decreases.Radial vectors of absolute velocities and relative velocities change slightly under the two large flow rate conditions.The research results can be applied to instruct the hydraulic optimization design of double blade pumps.展开更多
In this paper, particle image velocimetry (PIV) was used to measure the mean and root meansquare(RMS) velocity in the stirred tank with six-flat blade Rushton turbine and with no baffles. Two typesof motion patterns w...In this paper, particle image velocimetry (PIV) was used to measure the mean and root meansquare(RMS) velocity in the stirred tank with six-flat blade Rushton turbine and with no baffles. Two typesof motion patterns were studied. One was that the impeller runs at constant speed, the other was that the impellerruns at time-dependent speed and in a periodic way. The emphasis of the paper was on the comparison of meanand RMS velocity vector maps and profiles between these two types of motion patterns, and especial attention waspaid to the comparison of the mean velocity, time-averaged RMS velocity, phase averaged RMS velocity betweenthe constant 3 RPS (revolution per second) and time-dependent operation. The Reynolds number was between 763and 1527. The study explained the mechanism that time-dependent RPS is more efficient for mixing than that ofconstant RPS.展开更多
Unsteady three-dimensional flow phenomena must be investigated and well understood to be able to design devices to control such complex flow phenomena in order to achieve the desired behavior of the flow and to assess...Unsteady three-dimensional flow phenomena must be investigated and well understood to be able to design devices to control such complex flow phenomena in order to achieve the desired behavior of the flow and to assess their performance, even in harsh industrial environments. Experimental investigations for flow control research require measurement techniques capable to resolve the flow field with high spatial and temporal resolution to be able to perceive the relevant phenomena. Particle Image Velocimetry (PIV), providing access to the unsteady flow velocity field, is a measurement technique which is readily available commercially today. This explains why PIV is widely used for flow control research. A number of standard configurations exist, which, with increasing complexity, allow capturing flow velocity data instantaneously in geometrical arrangements extending from planes to volumes and in temporal arrangements extending from snapshots to temporarily well resolved data. With increasing complexity these PIV systems require advancing expertise of the user and growing investment costs. Using typical problems of flow control research, three different standard PIV systems will be characterized briefly. It is possible to upgrade a PIV system from a simple planar to a “high end” tomographic PIV system over a period of time, if sufficient PIV expertise can be built up and budget for additional investments becomes available.展开更多
Understanding the flow characteristic in fishways is crucial for efficient fish migration. Flow characteristic measurements can generally provide quantitative information of velocity distributions in such passages;Par...Understanding the flow characteristic in fishways is crucial for efficient fish migration. Flow characteristic measurements can generally provide quantitative information of velocity distributions in such passages;Particle Image Velocimetry (PIV) has become one of the most versatile techniques to disclose flow fields in general and in fishways, in particular. This paper firstly gives an overview of fish migration along with fish ladders and then the application of PIV measurements on the fish migration process. The overview shows that the quantitative and detailed turbulent flow information in fish ladders obtained by PIV is critical for analyzing turbulent properties and validating numerical results.展开更多
In-flight particle velocity and flux distribution were measured using CCD thermal spray monitor system during supersonic plasma spray processing with nano-structured Al_2O_3-TiO_2 feed stocks. According to the results...In-flight particle velocity and flux distribution were measured using CCD thermal spray monitor system during supersonic plasma spray processing with nano-structured Al_2O_3-TiO_2 feed stocks. According to the results of particle flux measurement, the largest radian of the divergent particle stream is about 0.2. Within the measuring range, top speed of in-flight particles reached 800m/s. Particle acceleration was accomplished within 4cm down stream of the nozzle. Average particle velocity (about 450m/s) exceeded local sound speed (340m/s) even at a mean standoff distance of 17cm. With increasing mean standoff distance, average velocity of in-flight particle decreased according to a parabolic rule approximately. Image diagnosis showed that the result of in-flight particle velocity measurement is credible.展开更多
The Particle Velocity Sensor (PVS) is a kind of acoustic transducer which measures the particle velocity directly with figure-of-eight directivity. This paper proposes a near-field noise scanning technology based on t...The Particle Velocity Sensor (PVS) is a kind of acoustic transducer which measures the particle velocity directly with figure-of-eight directivity. This paper proposes a near-field noise scanning technology based on the research of PVS, pressure-particle velocity (P-U) probe, and its application in noise source identification. Firstly, the principle and characteristics of PVS are presented. Secondly, a P-U probe is designed on the basis of PVS development. Finally, the noise measurement experiment for a single source is arranged and conducted. The result shows that the proposed P-U probe performs well in near-field noise source identification and localization.展开更多
Velocity is a key parameter characterizing the movement of saltating particles. High-speed photography is an efficient method to record the velocity. But, manually determining the relevant information from these photo...Velocity is a key parameter characterizing the movement of saltating particles. High-speed photography is an efficient method to record the velocity. But, manually determining the relevant information from these photographs is quite laborious. However, particle tracking velocimetry（PTV） can be used to measure the instantaneous velocity in fluids using tracer particles. The tracer particles have three basic features in fluids： similar movement patterns within a small region, a uniform particle distribution, and high particle density. Unfortunately, the saltation of sand particles in air is a stochastic process, and PTV has not yet been able to accurately determine the velocity field in a cloud of blowing sand. The aim of the present study was to develop an improved PTV technique to measure the downwind（horizontal） and vertical velocities of saltating sand. To demonstrate the feasibility of this new technique, we used it to investigate two-dimensional saltation of particles above a loose sand surface in a wind tunnel. We analyzed the properties of the saltating particles, including the probability distribution of particle velocity, variations in the mean velocity as a function of height, and particle turbulence. By automating much of the analysis, the improved PTV method can satisfy the requirement for a large sample size and can measure the velocity field of blowing sand more accurately than previously-used techniques. The results shed new light on the complicated mechanisms involved in sand saltation.展开更多
Application of particle image velocity (PIV) techniques for measuringparticle size distribution and total number in an activation chamber of desulfurization system isintroduced. Watersheld algorithm is used to choose ...Application of particle image velocity (PIV) techniques for measuringparticle size distribution and total number in an activation chamber of desulfurization system isintroduced. Watersheld algorithm is used to choose the suitable initial gray level threshold whichis used to change the gray level images taken by PIV to black and white ones, then every particle inan image is isolated totally. For every isolating particle, its contour is tracked by the edgeenhancement filter function and kept by Freeman s chain code. Based on a set of particle s chincode, its size and size distribution are calculated and sorted. Finally, the experimental data ofcalcium particles and water drops, separately injected into the activation chamber, and the erroranalysis of data are given out.展开更多
A novel single color camera trichromatic mask 3D-PIV technique suitable for measurement of complex flow fields in confined spaces is presented in this paper.By using a trichromatic mask to modulate the imaging optical...A novel single color camera trichromatic mask 3D-PIV technique suitable for measurement of complex flow fields in confined spaces is presented in this paper.By using a trichromatic mask to modulate the imaging optical path of a color camera,the RGB(Red,Green,and Blue)channels of the photosensitive chip were used to record full-frame full-resolution images of tracer particles from three viewing angles.The MLOS-SMART particle reconstruction algorithm was used to obtain three-dimensional particle distribution matrix from particle trichromatic mask images.The impact of parameters such as the inter-hole spacing and hole diameter of the trichromatic mask on the quality of particle reconstruction was analyzed.Through numerical simulation experiments on artificially synthesized three-dimensional flow fields of Gaussian vortex rings,the practicality of this technique in measuring three-dimensional transient velocity fields and the accuracy of velocity measurements were examined.The accuracy and feasibility of the technique are illustrated based on experimental measurements of a zero-net-mass-flux jet.展开更多
基金This work was financially supported by the National Natural Science Foundation of China(Grant Nos.42225702 and 42077235)the Open Research Project Program of the State Key Laboratory of Internet of Things for Smart City(University of Macao)(Grant No.SKL-IoTSC(UM)-2021-2023/ORP/GA10/2022)。
文摘Monitoring shear deformation of sliding zones is of great significance for understanding the landslide evolution mechanism,in which fiber optic strain sensing has shown great potential.However,the cor-relation between strain measurements of quasi-distributed fiber Bragg grating(FBG)sensing arrays and shear displacements of surrounding soil remains elusive.In this study,a direct shear model test was conducted to simulate the shear deformation of sliding zones,in which the soil internal deformation was captured using FBG strain sensors and the soil surface deformation was measured by particle image velocimetry(PIV).The test results show that there were two main slip surfaces and two secondary ones,developing a spindle-shaped shear band in the soil.The formation of the shear band was successfully captured by FBG sensors.A sinusoidal model was proposed to describe the fiber optic cable deformation behavior.On this basis,the shear displacements and shear band widths were calculated by using strain measurements.This work provides important insight into the deduction of soil shear deformation using soil-embedded FBG strain sensors.
文摘Aim To investigate the spray particle velocity and its distribution characteristics. Methods\ A set of PIV (particle image velocimetry) system was developed and used to observe and analyze the spray particle velocity field. Results and Conclusion\ Double exposure image of the spray particle within the region of 10-50 mm from the nozzle tip was recorded and analyzed by the IBAS2000 analysis system. Some characteristics of the spray particle velocity and its distribution were obtained.
基金This project is supported by National Natural Science Foundation of China(No.50136030) Opening Research Work from Key Laboratory of Jiangsu Province on Hydro-Dynamics Engineering in Yangzhou University, China.
文摘A special transparent centrifugal pump is designed. Detailed opticalmeasurements of the flow inside the rotating passages of a five-bladed shroud centrifugal pumpimpeller have been performed by using two-dimensional particle image velocimetry (PIV). The flow issurveyed at three load conditions q_V/q_(Vd) = 0.4, q_V/q_(Vd) = 1.0, q_V/q_(Vd) = 1.5,respectively. As a result, phase averaged PIV velocity vector maps on three planes between hub andshroud of the impeller are presented. At design load, the mean field of relative velocity ispredominantly vane congruent, showing well-behaved flow without separation. The distributions of therelative velocity on different plane along the pump shaft are very different and there is always alow velocity zone near the pressure-side of the blade at both low and design flow rate, but thelow-velocity-zone at the low flow rate is much larger than that at the design one. The studydemonstrates that the PIV technique is efficient in providing reliable and detailed velocity dataover a full impeller passage.
基金Project supported by the National Basic Research Program of China (973 Program) (No. 2007CB714600)
文摘Large-view flow field measurements using the particle image velocimetry （PIV） technique with high resolution CCD cameras on a rotating 1/8 scale blade model of the NREL UAE phase VI wind turbine are conducted in the engineering-oriented q53.2 m wind tunnel. The motivation is to establish the database of the initiation and development of the tip vortex to study the flow structure and mechanism of the wind turbine. The results show that the tip vortex first moves inward for a very short period and then moves outward with the wake expansion, while its vorticity decreases with time after being trailed from the trailing edge of the blade tip, and then increases continuously with the rapid rolling-up to form a strong tip vortex. The measurements also indicate that the downstream movement of the tip vortex is nearly linear in the very near wake under the test condition.
基金sponsored by the National Natural Science Foundation of China (Project No. 51508282)K. C. Wong Magna Fund in Ningbo University, China Postdoctoral Science Foundation(No.2017M611674)Fundamental Research Funds for the Central Universities (2017B13614)
文摘A new small-scale geotechnical physical model in 1-g and unconfined condition, combining the transparent soil, close-range photogrammetry and particle image velocimetry(PIV), was employed, which provides a non-intrusively internal deformation measurement approach to monitor the internal deformation of soil caused by expanded-base pile jacking with casing. The transparent soil was made of fused quartz and its refractive index matched blended oil, adding reflective particles(glass beads). Closerange photogrammetry was employed to record the images of the process of casing jacking and extraction in transparent soil, allowing the use of Matlab-based Geo-PIV to figure out the displacement field converted from image space to object space. Analysis of test results indicates that the maximum displacement caused by casing jacking for expandedconical-base pile is decreased by 29% compared with that for expanded-flat-base pile. The main movement happens at the early stage of casing extraction. The maximum displacement caused by casing extraction for the conical base is about 43% of that for the flatbase, while the affected zone caused by casing extraction for the conical base accounts for about 1/3 of that for the flat base. The contraction for horizontal displacements tends to decrease with the depth increasing. By contrast, the contraction under pile base decreases with the increasing of displacement. The displacements generated by jacking a conventional pile having a diameter equal to the casing diameter of the expanded-base pile were comparable to the net displacement taking place due to expanded-base pile installation for the conical base pile.
基金supported by National Natural Science Foundation of China (Grant No. 50575017, Grant No. 50875016)
文摘The failure of a drilling pump is always due to the break of the drilling pump valve, which is one of the most important but also the weakest parts of the drilling pump. Over the decades, the degradation of drilling pump valves has been investigated extensively and various failure mechanisms have been proposed. However, no experimental test on the fluid has been successfully performed to support some of these mechanisms. In this paper, tests of the flow within the valve play are carried out to investigate the factors resulting in the failure of the valve. In the tests, particle image velocimetry（PIV） technology is employed to measure the flow field distribution of the valve play in the model. From these tests, the distributions of velocity and vorticity of fluid in ＇various valves with different valve angles and different valve lifts are obtained, from which the features of flow fields are derived and generalized. Subsequently, a general rule of the influence of valve angles and valve lifts on the flow velocity is concluded according to chart analyses of maximal velocities and mean velocities. Finally, an analysis is made on the possibility of valve failure caused by erosion and abrasion in a working valve, with the application of the failure mechanisms of drilling pump valves. PIV measurement improves the study on the failure of the drilling pump valve, and the results show good agreement with previous computational fluid dynamics（CFD） simulations.
基金Supported by the National Natural Science Foundation of China(Nos.31072246,31272703)
文摘This article reports a particle image velocimetry study and the comparative results of a numerical simulation into the hydrodynamic characteristics around an artificial reef.We reveal the process of flow separation and vortex evolution,and compare the force terms generated by our artificial reef model.The numerical simulation agrees well with experimental results,showing the applicability of computational fluid dynamics to the hydrodynamics of an artificial reef.Furthermore,we numerically simulate the hydrodynamics of the reef model for seven velocities.The results show that the drag coefficient is approximately 1.21 in a self-modeling region for Reynolds numbers between 2.123×104and 9×104.Therefore,the upwelling height and current width of the flow field do not change significantly when the inflow velocity increases.Our study indicates that computational fluid dynamics can be applied to study the hydrodynamics of an artificial reef and offer clues to its construction.
基金supported by National Outstanding Young Scientists Founds of China (Grant No. 50825902)National Key Technology R&D Program of China (Grant No. 2008BAF34B15)+2 种基金National Natural Science Foundation of China (Grant No. 51079062)Jiangsu Provincial 333 High-level Personal Training Project of ChinaJiangsu Provincial Six Talent Peak of China
文摘The double blade pump is widely used in sewage treatment industry,however,the research on the internal flow characteristics of the double blade pump with particle image velocimetry（PIV） technology is very little at present.To reveal inner flow characteristics in double blade pump impeller under off-design and design conditions,inner flows in a double blade pump impeller,whose specific speed is 111,are measured under the five off-design conditions and design condition by using 3D PIV test technology.In order to ensure the accuracy of the 3D PIV test,the external trigger synchronization system which makes use of fiber optic and equivalent calibration method are applied.The 3D PIV relative velocity synthesis procedure is compiled by using Visual C＋＋ 2005.Then absolute velocity distribution and relative velocity distribution in the double blade pump impeller are obtained.Test results show that vortex exists in each condition,but the location,size and velocity of vortex core are different.Average absolute velocity value of impeller outlet increases at first,then decreases,and then increases again with increase of flow rate.Again average relative velocity values under 0.4,0.8,and 1.2 design condition are higher than that under 1.0 design condition,while under 0.6 and 1.4 design condition it is lower.Under low flow rate conditions,radial vectors of absolute velocities at impeller outlet and blade inlet near the pump shaft decrease with increase of flow rate,while that of relative velocities at the suction side near the pump shaft decreases.Radial vectors of absolute velocities and relative velocities change slightly under the two large flow rate conditions.The research results can be applied to instruct the hydraulic optimization design of double blade pumps.
文摘In this paper, particle image velocimetry (PIV) was used to measure the mean and root meansquare(RMS) velocity in the stirred tank with six-flat blade Rushton turbine and with no baffles. Two typesof motion patterns were studied. One was that the impeller runs at constant speed, the other was that the impellerruns at time-dependent speed and in a periodic way. The emphasis of the paper was on the comparison of meanand RMS velocity vector maps and profiles between these two types of motion patterns, and especial attention waspaid to the comparison of the mean velocity, time-averaged RMS velocity, phase averaged RMS velocity betweenthe constant 3 RPS (revolution per second) and time-dependent operation. The Reynolds number was between 763and 1527. The study explained the mechanism that time-dependent RPS is more efficient for mixing than that ofconstant RPS.
文摘Unsteady three-dimensional flow phenomena must be investigated and well understood to be able to design devices to control such complex flow phenomena in order to achieve the desired behavior of the flow and to assess their performance, even in harsh industrial environments. Experimental investigations for flow control research require measurement techniques capable to resolve the flow field with high spatial and temporal resolution to be able to perceive the relevant phenomena. Particle Image Velocimetry (PIV), providing access to the unsteady flow velocity field, is a measurement technique which is readily available commercially today. This explains why PIV is widely used for flow control research. A number of standard configurations exist, which, with increasing complexity, allow capturing flow velocity data instantaneously in geometrical arrangements extending from planes to volumes and in temporal arrangements extending from snapshots to temporarily well resolved data. With increasing complexity these PIV systems require advancing expertise of the user and growing investment costs. Using typical problems of flow control research, three different standard PIV systems will be characterized briefly. It is possible to upgrade a PIV system from a simple planar to a “high end” tomographic PIV system over a period of time, if sufficient PIV expertise can be built up and budget for additional investments becomes available.
文摘Understanding the flow characteristic in fishways is crucial for efficient fish migration. Flow characteristic measurements can generally provide quantitative information of velocity distributions in such passages;Particle Image Velocimetry (PIV) has become one of the most versatile techniques to disclose flow fields in general and in fishways, in particular. This paper firstly gives an overview of fish migration along with fish ladders and then the application of PIV measurements on the fish migration process. The overview shows that the quantitative and detailed turbulent flow information in fish ladders obtained by PIV is critical for analyzing turbulent properties and validating numerical results.
文摘In-flight particle velocity and flux distribution were measured using CCD thermal spray monitor system during supersonic plasma spray processing with nano-structured Al_2O_3-TiO_2 feed stocks. According to the results of particle flux measurement, the largest radian of the divergent particle stream is about 0.2. Within the measuring range, top speed of in-flight particles reached 800m/s. Particle acceleration was accomplished within 4cm down stream of the nozzle. Average particle velocity (about 450m/s) exceeded local sound speed (340m/s) even at a mean standoff distance of 17cm. With increasing mean standoff distance, average velocity of in-flight particle decreased according to a parabolic rule approximately. Image diagnosis showed that the result of in-flight particle velocity measurement is credible.
文摘The Particle Velocity Sensor (PVS) is a kind of acoustic transducer which measures the particle velocity directly with figure-of-eight directivity. This paper proposes a near-field noise scanning technology based on the research of PVS, pressure-particle velocity (P-U) probe, and its application in noise source identification. Firstly, the principle and characteristics of PVS are presented. Secondly, a P-U probe is designed on the basis of PVS development. Finally, the noise measurement experiment for a single source is arranged and conducted. The result shows that the proposed P-U probe performs well in near-field noise source identification and localization.
基金funded by the Young Talent Fund of University Association for Science and Technology in Shaanxi, China (20170303)the National Science Basic Research Plan in Shaanxi Province of China (2017JQ6080)the Talent Development Project of Weinan Normal University, China (16ZRRC02)
文摘Velocity is a key parameter characterizing the movement of saltating particles. High-speed photography is an efficient method to record the velocity. But, manually determining the relevant information from these photographs is quite laborious. However, particle tracking velocimetry（PTV） can be used to measure the instantaneous velocity in fluids using tracer particles. The tracer particles have three basic features in fluids： similar movement patterns within a small region, a uniform particle distribution, and high particle density. Unfortunately, the saltation of sand particles in air is a stochastic process, and PTV has not yet been able to accurately determine the velocity field in a cloud of blowing sand. The aim of the present study was to develop an improved PTV technique to measure the downwind（horizontal） and vertical velocities of saltating sand. To demonstrate the feasibility of this new technique, we used it to investigate two-dimensional saltation of particles above a loose sand surface in a wind tunnel. We analyzed the properties of the saltating particles, including the probability distribution of particle velocity, variations in the mean velocity as a function of height, and particle turbulence. By automating much of the analysis, the improved PTV method can satisfy the requirement for a large sample size and can measure the velocity field of blowing sand more accurately than previously-used techniques. The results shed new light on the complicated mechanisms involved in sand saltation.
基金The Special Funds for State Key Projects for Fun- damental Research (G1999022201-04).
文摘Application of particle image velocity (PIV) techniques for measuringparticle size distribution and total number in an activation chamber of desulfurization system isintroduced. Watersheld algorithm is used to choose the suitable initial gray level threshold whichis used to change the gray level images taken by PIV to black and white ones, then every particle inan image is isolated totally. For every isolating particle, its contour is tracked by the edgeenhancement filter function and kept by Freeman s chain code. Based on a set of particle s chincode, its size and size distribution are calculated and sorted. Finally, the experimental data ofcalcium particles and water drops, separately injected into the activation chamber, and the erroranalysis of data are given out.
基金co-supported by the National Natural Science Foundation of China(Nos.12102284,12172242,12332017)the Shanxi Province Science Foundation for Youths,China(No.20210302124262)the Chunhui Project Foundation of the Education Department of China(No.202200257)。
文摘A novel single color camera trichromatic mask 3D-PIV technique suitable for measurement of complex flow fields in confined spaces is presented in this paper.By using a trichromatic mask to modulate the imaging optical path of a color camera,the RGB(Red,Green,and Blue)channels of the photosensitive chip were used to record full-frame full-resolution images of tracer particles from three viewing angles.The MLOS-SMART particle reconstruction algorithm was used to obtain three-dimensional particle distribution matrix from particle trichromatic mask images.The impact of parameters such as the inter-hole spacing and hole diameter of the trichromatic mask on the quality of particle reconstruction was analyzed.Through numerical simulation experiments on artificially synthesized three-dimensional flow fields of Gaussian vortex rings,the practicality of this technique in measuring three-dimensional transient velocity fields and the accuracy of velocity measurements were examined.The accuracy and feasibility of the technique are illustrated based on experimental measurements of a zero-net-mass-flux jet.
