Soft clay soils cannot usually support large lateral loads,so clay soils must be improved to increase lateral resistance.The jet grouting method is one of the methods used to improve weak soils.In this paper,a series ...Soft clay soils cannot usually support large lateral loads,so clay soils must be improved to increase lateral resistance.The jet grouting method is one of the methods used to improve weak soils.In this paper,a series of 3D finite element studies were conducted using Plaxis 3D software to investigate the lateral behavior of piled rafts in improved soft clay utilizing the jet grouting method.Parametric models were analyzed to explore the influence of the width,depth,and location of the grouted clay on the lateral resistance.Additionally,the effect of vertical loads on the lateral behavior of piled rafts in grouted clay was also investigated.The numerical results indicate that the lateral resistance increases by increasing the dimensions of the jet grouting beneath and around the piled raft.Typical increases in lateral resistance are 11.2%,65%,177%,and 35%for applying jet grouting beside the raft,below the raft,below and around the raft,and grouted strips parallel to lateral loads,respectively.It was also found that increasing the depth of grouted clay enhances lateral resistance up to a certain depth,about 6 to 10 times the pile diameter(6 to 10D).In contrast,the improvement ratio is limited beyond 10D.Furthermore,the results demonstrate that the presence of vertical loads has a significant impact on sideward resistance.展开更多
This paper discusses a new technique to improve soft ground with grouting piles and deep mixing piles. The bearing capacity of composite ground and the stress ratio between piles and soil is discussed by means of the ...This paper discusses a new technique to improve soft ground with grouting piles and deep mixing piles. The bearing capacity of composite ground and the stress ratio between piles and soil is discussed by means of the static test. Based on Mindlin solution and Boussinesq solution, the additional stress and settlement of the composite ground are acquired.Compared the practical value with calculation, a better calculating method is confirmed.展开更多
The reliability of post grouting pile axial resistance was studied by proposing a design method for its probabilistic limit state,which is represented by the partial coefficients of load,end,and side resistance.The hy...The reliability of post grouting pile axial resistance was studied by proposing a design method for its probabilistic limit state,which is represented by the partial coefficients of load,end,and side resistance.The hyperbolic,modified hyperbolic,and polynomial models were employed to predict the ultimate bearing capacity of test piles that were not loaded to damage in field tests.The results were used for the calculation and calibration of the reliability index.The reliability of the probabilistic limit state design method was verified by an engineering case.The results show that the prediction results obtained from the modified hyperbolic model are closest to those obtained through the static load test.The proposed corresponding values of total,side,and end resistance partial coefficients are 1.84,1.66,and 2.73 when the dead and live load partial coefficients are taken as 1.1 and 1.4,respectively.Meanwhile,the corresponding partial coefficients of total,side,and end resistance are 1.70,1.56,and 2.34 when the dead and live load partial coefficients are taken as 1.2 and 1.4,respectively.展开更多
The simplified mechanical model and finite element model are established on the basis of the measured results and analysis of the grouting pile deformation monitoring,surface horizontal displacement and vertical displ...The simplified mechanical model and finite element model are established on the basis of the measured results and analysis of the grouting pile deformation monitoring,surface horizontal displacement and vertical displacement monitoring,deep horizontal displacement(inclinometer)monitoring,soil pressure monitoring and seepage pressure monitoring in the lower reaches of Wuan River regulation project in Shishi,Fujian Province.The mechanical behavior and deformation performance of mould-bag pile retaining wall formed after controlled cement grouting in the silty stratum of the test section are analyzed and compared.The results show that the use of controlled cement grouting mould-bag pile technology is to strengthen the soft stratum for sealing water and reinforcement,so that it can rock into a retaining wall,which can both retain soil and seal water with excellent effect.The control of cement grouting technology not only makes the soft soil rock in the range of retaining wall of mould-bag pile,but also makes a wide range of soil around the mould-bag pile squeeze and embed to compaction;and its cohesion and internal friction angle increased,so as to achieve the purpose of reducing soil pressure and improving mechanical and deformation properties of retaining wall.展开更多
This paper deals with a new type of crushed stone grouting pile with a rigid bearing plate. The load transfer characteristics were analyzed, and a settlement model of the composite foundation reinforced with crushed s...This paper deals with a new type of crushed stone grouting pile with a rigid bearing plate. The load transfer characteristics were analyzed, and a settlement model of the composite foundation reinforced with crushed stone grouting pile and rigid bearing plate was built by FEM program. The effects of replacement ratio of capping plate, replacement ratio of pile, replacement ratio of grout diffusion zone, pile-soil modulus ratio, and serous-soil modulus ratio, on the composite foundation settlement were discussed. It is concluded that the proposed crushed stone grouting pile with a rigid bearing plate is effective in decreasing the settlement of composite foundation.展开更多
Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, ...Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, study on reinforcement mechanism and design calculation method of composite foundation of grouting pile is initially started without design specifications, so it is usually required to draw on design specifications of stump pile when designing composite foundation of grouting pile while grouting pile has its characteristics and difference although reinforcement mechanisms and construction processes of two types of piles are similar. Sedimentation formula of composite foundation of grouting pile with cover plate is educed and a suitable deformation mode is proposed by aiming to deformation characteristics of composite foundation of grouting pile with cover plate under embankment load on basis of relevant sedimentation theories of composite foundation by combination of characteristics of composite foundation of grouting pile. The sedimentation calculation formula of grouting pile with cover plate under embankment load is educed according to balance relation of force and displacement coordination conditions by elastic theory and sedimentation calculation model established is validated by sedimentation monitoring documents of one expressway in China.展开更多
Application of pressured grouting method (PGM) in pile engineering can tackle problems encountered during construction of bored piles. Bearing capacity of piles can be increased through compaction of subsoils around p...Application of pressured grouting method (PGM) in pile engineering can tackle problems encountered during construction of bored piles. Bearing capacity of piles can be increased through compaction of subsoils around piles. This paper reports research efforts of this technique by the pile research team in Southwest Jiaotong University in last decade with respect to the construction process, test findings, and primary research conclusions. The social-economical benefits of this method and application market in pile engineering are also analyzed.展开更多
The grouting method applied in bored pile is an improvement to the conventional bored pile. Load tests have proved that grouting under the bored pile tip is an effective method to enhance the bearing capacity of the p...The grouting method applied in bored pile is an improvement to the conventional bored pile. Load tests have proved that grouting under the bored pile tip is an effective method to enhance the bearing capacity of the pile and to reduce the pile settlement. In this paper, the grouting technology is described and pile load test results are discussed. In order to put the grouting method into design practice, the authors analyze the working mechanism of soil compaction. And, based on the theory of cavities expansion in soil mass, approximate formulae are proposed for estimating the bearing capacity of the grouted pile. The theoretical prediction agrees well with the load test results.展开更多
我国东南沿海尤其是温州地区广泛存在上覆深厚软土下覆不均匀卵石的地层。该区域的钻孔灌注桩常采用后注浆技术改善其承载性能。为了评价后注浆技术对这类地层中灌注桩承载力改善效果,开展了相应的模型试验,对比了不同注浆量对桩承载力...我国东南沿海尤其是温州地区广泛存在上覆深厚软土下覆不均匀卵石的地层。该区域的钻孔灌注桩常采用后注浆技术改善其承载性能。为了评价后注浆技术对这类地层中灌注桩承载力改善效果,开展了相应的模型试验,对比了不同注浆量对桩承载力的影响程度;并结合扫描电镜(scanning electron microscope,简称SEM)试验分析了浆液分布特点,探讨了浆液在卵石层中的扩散范围,研究了浆液扩散范围与桩承载力之间的关系。结果表明:浆液能够有效地填充桩端卵石层,注浆量的增加使得填充范围扩大,填充范围为3~4倍桩径时,桩的承载力改善最显著。在不均匀卵石持力层中存在一个最优注浆量,最优归一化注浆量约为2.8,若超过该最优注浆量归一化值,桩的承载力不再显著提高。单桩模型试验确定的最优注浆量与刘金砺公式[1]的预测结果接近。扫描电镜技术有助于评价桩的后注浆技术在上覆深厚软土下覆不均匀卵石的土层中的效果。展开更多
文摘Soft clay soils cannot usually support large lateral loads,so clay soils must be improved to increase lateral resistance.The jet grouting method is one of the methods used to improve weak soils.In this paper,a series of 3D finite element studies were conducted using Plaxis 3D software to investigate the lateral behavior of piled rafts in improved soft clay utilizing the jet grouting method.Parametric models were analyzed to explore the influence of the width,depth,and location of the grouted clay on the lateral resistance.Additionally,the effect of vertical loads on the lateral behavior of piled rafts in grouted clay was also investigated.The numerical results indicate that the lateral resistance increases by increasing the dimensions of the jet grouting beneath and around the piled raft.Typical increases in lateral resistance are 11.2%,65%,177%,and 35%for applying jet grouting beside the raft,below the raft,below and around the raft,and grouted strips parallel to lateral loads,respectively.It was also found that increasing the depth of grouted clay enhances lateral resistance up to a certain depth,about 6 to 10 times the pile diameter(6 to 10D).In contrast,the improvement ratio is limited beyond 10D.Furthermore,the results demonstrate that the presence of vertical loads has a significant impact on sideward resistance.
文摘This paper discusses a new technique to improve soft ground with grouting piles and deep mixing piles. The bearing capacity of composite ground and the stress ratio between piles and soil is discussed by means of the static test. Based on Mindlin solution and Boussinesq solution, the additional stress and settlement of the composite ground are acquired.Compared the practical value with calculation, a better calculating method is confirmed.
基金The National Natural Science Foundation of China(No.51878160,52008100,52078128).
文摘The reliability of post grouting pile axial resistance was studied by proposing a design method for its probabilistic limit state,which is represented by the partial coefficients of load,end,and side resistance.The hyperbolic,modified hyperbolic,and polynomial models were employed to predict the ultimate bearing capacity of test piles that were not loaded to damage in field tests.The results were used for the calculation and calibration of the reliability index.The reliability of the probabilistic limit state design method was verified by an engineering case.The results show that the prediction results obtained from the modified hyperbolic model are closest to those obtained through the static load test.The proposed corresponding values of total,side,and end resistance partial coefficients are 1.84,1.66,and 2.73 when the dead and live load partial coefficients are taken as 1.1 and 1.4,respectively.Meanwhile,the corresponding partial coefficients of total,side,and end resistance are 1.70,1.56,and 2.34 when the dead and live load partial coefficients are taken as 1.2 and 1.4,respectively.
基金The work is supported by the National Natural Science Foundation of China(No.51578253)Scientific and Technological Planning Project of Xiamen City(Nos.3502Z20172011 and 3502Z20172014)+1 种基金Scientific and Technological Planning Project of Quanzhou City(No.2018C083R)Reform study of graduate education and teaching of Huaqiao University in 2018(No.18YJG55).
文摘The simplified mechanical model and finite element model are established on the basis of the measured results and analysis of the grouting pile deformation monitoring,surface horizontal displacement and vertical displacement monitoring,deep horizontal displacement(inclinometer)monitoring,soil pressure monitoring and seepage pressure monitoring in the lower reaches of Wuan River regulation project in Shishi,Fujian Province.The mechanical behavior and deformation performance of mould-bag pile retaining wall formed after controlled cement grouting in the silty stratum of the test section are analyzed and compared.The results show that the use of controlled cement grouting mould-bag pile technology is to strengthen the soft stratum for sealing water and reinforcement,so that it can rock into a retaining wall,which can both retain soil and seal water with excellent effect.The control of cement grouting technology not only makes the soft soil rock in the range of retaining wall of mould-bag pile,but also makes a wide range of soil around the mould-bag pile squeeze and embed to compaction;and its cohesion and internal friction angle increased,so as to achieve the purpose of reducing soil pressure and improving mechanical and deformation properties of retaining wall.
文摘This paper deals with a new type of crushed stone grouting pile with a rigid bearing plate. The load transfer characteristics were analyzed, and a settlement model of the composite foundation reinforced with crushed stone grouting pile and rigid bearing plate was built by FEM program. The effects of replacement ratio of capping plate, replacement ratio of pile, replacement ratio of grout diffusion zone, pile-soil modulus ratio, and serous-soil modulus ratio, on the composite foundation settlement were discussed. It is concluded that the proposed crushed stone grouting pile with a rigid bearing plate is effective in decreasing the settlement of composite foundation.
文摘Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, study on reinforcement mechanism and design calculation method of composite foundation of grouting pile is initially started without design specifications, so it is usually required to draw on design specifications of stump pile when designing composite foundation of grouting pile while grouting pile has its characteristics and difference although reinforcement mechanisms and construction processes of two types of piles are similar. Sedimentation formula of composite foundation of grouting pile with cover plate is educed and a suitable deformation mode is proposed by aiming to deformation characteristics of composite foundation of grouting pile with cover plate under embankment load on basis of relevant sedimentation theories of composite foundation by combination of characteristics of composite foundation of grouting pile. The sedimentation calculation formula of grouting pile with cover plate under embankment load is educed according to balance relation of force and displacement coordination conditions by elastic theory and sedimentation calculation model established is validated by sedimentation monitoring documents of one expressway in China.
文摘Application of pressured grouting method (PGM) in pile engineering can tackle problems encountered during construction of bored piles. Bearing capacity of piles can be increased through compaction of subsoils around piles. This paper reports research efforts of this technique by the pile research team in Southwest Jiaotong University in last decade with respect to the construction process, test findings, and primary research conclusions. The social-economical benefits of this method and application market in pile engineering are also analyzed.
文摘The grouting method applied in bored pile is an improvement to the conventional bored pile. Load tests have proved that grouting under the bored pile tip is an effective method to enhance the bearing capacity of the pile and to reduce the pile settlement. In this paper, the grouting technology is described and pile load test results are discussed. In order to put the grouting method into design practice, the authors analyze the working mechanism of soil compaction. And, based on the theory of cavities expansion in soil mass, approximate formulae are proposed for estimating the bearing capacity of the grouted pile. The theoretical prediction agrees well with the load test results.
文摘我国东南沿海尤其是温州地区广泛存在上覆深厚软土下覆不均匀卵石的地层。该区域的钻孔灌注桩常采用后注浆技术改善其承载性能。为了评价后注浆技术对这类地层中灌注桩承载力改善效果,开展了相应的模型试验,对比了不同注浆量对桩承载力的影响程度;并结合扫描电镜(scanning electron microscope,简称SEM)试验分析了浆液分布特点,探讨了浆液在卵石层中的扩散范围,研究了浆液扩散范围与桩承载力之间的关系。结果表明:浆液能够有效地填充桩端卵石层,注浆量的增加使得填充范围扩大,填充范围为3~4倍桩径时,桩的承载力改善最显著。在不均匀卵石持力层中存在一个最优注浆量,最优归一化注浆量约为2.8,若超过该最优注浆量归一化值,桩的承载力不再显著提高。单桩模型试验确定的最优注浆量与刘金砺公式[1]的预测结果接近。扫描电镜技术有助于评价桩的后注浆技术在上覆深厚软土下覆不均匀卵石的土层中的效果。
