This paper presents a novel non-contact method for evaluating the resonant frequency of a microstructure, Firstly, the microstructure under test is excited by ultrasonic waves. This excitation method does not impose a...This paper presents a novel non-contact method for evaluating the resonant frequency of a microstructure, Firstly, the microstructure under test is excited by ultrasonic waves. This excitation method does not impose any undefined load on the specimen like the electrostatic excitation and also this is the first actual use of ultrasonic wave for exciting a microstructure in the literature. Secondly, the amplitudes of the microstructure are determined by image edge detection using a Mexican hat wavelet transform on the vibrating images of the microstructure. The vibrating images are captured by a CCD camera when the microstructure is vibrated by ultrasonic waves at a series of discrete high frequencies （〉30 kHz）. Upon processing the vibrating images, the amplitudes at various excitation frequencies are obtained and an amplitude-frequency spectrum is obtained from which the resonant frequency is subsequently evaluated. A micro silicon structure consisting of a perforated plate （192 × 192 μm） and two cantilever beams （76 × 43 μm） which is about 4 μm thickness is tested. Since laser interferometry is not required, thermal effects on a test object can be avoided. Hence, the setup is relatively simple. Results show that the proposed method is a simple and effective approach for evaluating the dynamic characteristics of microstructures.展开更多
To optimize the efficiency of the linear compressor,its operating frequency must be controlled equal to the system resonant frequency.The traditional resonant frequency tracking control algorithm relies on the steady ...To optimize the efficiency of the linear compressor,its operating frequency must be controlled equal to the system resonant frequency.The traditional resonant frequency tracking control algorithm relies on the steady state characteristics of the system,which suffers from slow convergence speed,low accuracy and slow system response.In order to solve these problems,a novel resonant frequency tracking control for linear compressor based on model reference adaptive system(MRAS)is proposed in this paper,and the parameter adaptive rate is derived by the Popov's hyperstability theory,so that the system resonant frequency can be directly calculated through the parameter adaptive rate.Furthermore,the traditional algorithm needs to calculate the piston stroke signal by integrating the back-EMF,which has the problem of integral drift.The algorithm proposed in this paper only needs the velocity signal,and the accuracy of the velocity calculation can be ensured by utilizing the self-adaptive band-pass filter(SABPF),thereby greatly improving the accuracy of the resonance frequency calculation.Simulation results verify the effectiveness of the proposed algorithm.展开更多
The introduction of machine learning (ML) in the research domain is a new era technique. The machine learning algorithm is developed for frequency predication of patterns that are formed on the Chladni plate and focus...The introduction of machine learning (ML) in the research domain is a new era technique. The machine learning algorithm is developed for frequency predication of patterns that are formed on the Chladni plate and focused on the application of machine learning algorithms in image processing. In the Chladni plate, nodes and antinodes are demonstrated at various excited frequencies. Sand on the plate creates specific patterns when it is excited by vibrations from a mechanical oscillator. In the experimental setup, a rectangular aluminum plate of 16 cm x 16 cm and 0.61 mm thickness was placed over the mechanical oscillator, which was driven by a sine wave signal generator. 14 Chladni patterns are obtained on a Chladni plate and validation is done with modal analysis in Ansys. For machine learning, a large number of data sets are required, as captured around 200 photos of each modal frequency and around 3000 photos with a camera of all 14 Chladni patterns for supervised learning. The current model is written in Python language and model has one convolution layer. The main modules used in this are Tensor Flow Keras, NumPy, CV2 and Maxpooling. The fed reference data is taken for 14 frequencies between 330 Hz to 3910 Hz. In the model, all the images are converted to grayscale and canny edge detected. All patterns of frequencies have an almost 80% - 99% correlation with test sample experimental data. This approach is to form a directory of Chladni patterns for future reference purpose in real-life application. A machine learning algorithm can predict the resonant frequency based on the patterns formed on the Chladni plate.展开更多
The dependences of spin wave resonance(SWR)frequency on the surface anisotropy field,interface exchange coupling,symmetry,biquadratic exchange(BQE)interaction,film thickness,and the external magnetic field in bilayer ...The dependences of spin wave resonance(SWR)frequency on the surface anisotropy field,interface exchange coupling,symmetry,biquadratic exchange(BQE)interaction,film thickness,and the external magnetic field in bilayer ferromagnetic films are theoretically analyzed by employing the linear spin wave approximation and Green’s function method.A remarkable increase of SWR frequency,except for energetically lower two modes,can be obtained in our model that takes the BQE interaction into account.Again,the effect of the external magnetic field on SWR frequency can be increased by increasing the biquadratic to interlayer exchange ratio.It has been identified that the BQE interaction is of utmost importance in improving the SWR frequency of the bilayer ferromagnetic films.In addition,for bilayer ferromagnetic films,the frequency gap between the energetically highest mode and lowest mode is found to increase by increasing the biquadratic to interlayer exchange ratio and film thickness and destroying the symmetry of the system.These results can be used to improve the understanding of magnetic properties in bilayer ferromagnetic films and thus may have prominent implications for future magnetic devices.展开更多
The flexible materials exhibit more favorable properties than most rigid substrates in flexibility,weight saving,mechanical reliability,and excellent environmental toughness.Particularly,flexible graphene film with un...The flexible materials exhibit more favorable properties than most rigid substrates in flexibility,weight saving,mechanical reliability,and excellent environmental toughness.Particularly,flexible graphene film with unique mechanical properties was extensively explored in high frequency devices.Herein,we report the characteristics of structure and magnetic properties at high frequency of Co2FeAl thin film with different thicknesses grown on flexible graphene substrate at room temperature.The exciting finding for the columnar structure of Co2FeAl thin film lays the foundation for excellent high frequency property of Co2FeAl/flexible graphene structure.In-plane magnetic anisotropy field varying with increasing thickness of Co2FeAl thin film can be obtained by measurement of ferromagnetic resonance,which can be ascribed to the enhancement of crystallinity and the increase of grain size.Meanwhile,the resonance frequency which can be achieved by the measurement of vector network analyzer with the microstrip method increases with increasing thickness of Co2FeAl thin film.Moreover,in our case with graphene film,the resonance magnetic field is quite stable though folded for twenty cycles,which demonstrates that good flexibility of graphene film and the stability of high frequency magnetic property of Co2FeAl thin film grown on flexible graphene substrate.These results are promising for the design of microwave devices and wireless communication equipment.展开更多
The objective of this study is to develop a simple tool for predicting the resonant frequency of the piston mode wave oscillation in a moonpool or a narrow gap between twin floating barges.Based on the dynamic analysi...The objective of this study is to develop a simple tool for predicting the resonant frequency of the piston mode wave oscillation in a moonpool or a narrow gap between twin floating barges.Based on the dynamic analysis and the domain-decomposition,a linear harmonic oscillator model for the fluid oscillation in a confined space is formulated,which immediately leads to an explicit dynamic solution for the resonant frequency.In the model,it is assumed that the water depth is equal to or greater than a critical value dependent on the ratio of the draft to the breadth of the floating body.The predicted resonant frequencies are compared with the numerical results of the linear potential model and the viscous fluid model,the semi-analytical potential solutions and the experimental measurements.Good agreements are observed for a wide range of geometric parameters of the moonpool and the narrow gap of either sharp or round edge shapes.The present dynamic method is also applied to predict the resonant frequency of the piston mode oscillation in the gap between a floating body and a vertical wall with a reasonable success.展开更多
A flextensional transducer with an Omega shape and its algorithmic method of the resonant frequency and the shape functions are suggested. The Omega transducer is separated into four parts treated respectively as a th...A flextensional transducer with an Omega shape and its algorithmic method of the resonant frequency and the shape functions are suggested. The Omega transducer is separated into four parts treated respectively as a thin shell of revolution and the theories of thin shells of revolution and piezoelectricity are used to obtain the energy functional of each part so that the sum of the energy functionals of the four parts is the energy functional of the whole Omega transducer. By substituting the shape functions with undetermined coefi3cients and the geo- metrical boundary conditions into the energy functional of the Omega transducer, the resonant frequency of the Omega transducer is firstly determined with the Rayleigh-Ritz method. With the gotten resonant frequency, the constant coefficients of the shape functions are following solved through the Rayleigh-Ritz partial differential equations and the geometrical boundary condition equations. The solving method of the resonant frequency and the shape functions is also extended to the cymbal transducer. Such an analytical method is verified to be feasible by the results of the finite element analysis and experiments. The research indicates that （1） The radial vibration of the piezoelectric ceramic is in phase with the longitudinal vibration of the top of metal cap, and it cut down the reversed phase component in the sound field. The Omega transducer can be a low frequency transducer. （2） The determination method of the resonant frequency and the shape functions give a solution to the optimum designs of the Omega transducer and the cymbal transducer. （3） The determination method of the resonant fi＇equency and the shape functions can also be used in other flextensional transducers or other structures which are composed of thin shells of revolution, so it is universal.展开更多
Gas-liquid coupling oscillation is a novel approach to reducing the resonant frequency and to elevating the pressure amplitude of a thermoacoustic engine.If a thermoacoustic engine is used to drive low-frequency pulse...Gas-liquid coupling oscillation is a novel approach to reducing the resonant frequency and to elevating the pressure amplitude of a thermoacoustic engine.If a thermoacoustic engine is used to drive low-frequency pulse tube refrigerators,the frequency matching between the thermoacoustic engine and the refrigerator plays an important role.Based on an acoustic-electric analogy,a lumped parameter model is proposed to estimate the resonant frequency of a standing-wave thermoacoustic engine with gas-liquid coupling oscillation.Furthermore,a simplified lumped parameter model is also developed to reduce the computation complexity.The resonant frequency dependence on the mean pressure,the gas space volume,and the water column length is computed and analyzed.The impact of different working gases on the resonant frequency is also discussed.The effectiveness of the models is validated by comparing the computed results with the experimental data of the gas-liquid coupling oscillation system.An increase in the mean working pressure can lead to a rise in the resonant frequency,and a lower resonant frequency can be achieved by elongating the liquid column.In comparison with nitrogen and argon,carbon dioxide can realize a lower frequency due to a smaller specific heat ratio.展开更多
In this paper, an analytical model for computing the resonant frequency of the gap-coupled ring microstrip patch antennas is developed. The analytical model is based upon the cavity model along with circuit theory. Us...In this paper, an analytical model for computing the resonant frequency of the gap-coupled ring microstrip patch antennas is developed. The analytical model is based upon the cavity model along with circuit theory. Using the field expressions and boundary conditions, the transcendental equation for the structure is developed. The analytically computed results are compared with the simulated results. The simulation work is carried out by using computer simulation technology(CST) microwave studio simulator.The comparison between simulated and computed results shows good agreement.展开更多
We report on the generation of self-oscillations from a continuously pumped singly resonant frequency doubler based on a periodically poled potassium titanyl phosphate crystal （PPKTP）. The sustained square-wave and ...We report on the generation of self-oscillations from a continuously pumped singly resonant frequency doubler based on a periodically poled potassium titanyl phosphate crystal （PPKTP）. The sustained square-wave and staircase curve of self-oscillations are obtained when the incident pump powers are below and above the threshold of subharmonic-pumped parametric oscillation （SPO）, respectively. The self-oscillations can be explained by the competition between the phase shifts induced by cascading nonlinearity and thermal effect, and the influence of fundamental nonlinear phase shift by the generation of SPO. The simulation results are in good agreement with the experiment data.展开更多
Proportional integrator (PI) is always adopted in the resonant frequency servo loop in a resonator micro optic gyro (RMOG). The oscillation phenomenon is observed when adjusting the loop gain surpassing a threshold. T...Proportional integrator (PI) is always adopted in the resonant frequency servo loop in a resonator micro optic gyro (RMOG). The oscillation phenomenon is observed when adjusting the loop gain surpassing a threshold. This phenomenon limits system performance on step response speed and residual error. Based on the experiment system, a simulation model was set up. Further analysis shows that the threshold gain is related to the system loop filter setting and the loop delay. The traditional PI frequency servo loop technique in the RMOG system cannot keep up with the environment's disturbance quickly enough, which leads to a large residual error. A compensating method is proposed to optimize the tracking performance, solve the oscillation problem, and speed up the system response. Simulation and experiment results show that the compensated system is superior in performance. It has less residual error in the stable state and is 10 times quicker than the uncompensated system on the step response.展开更多
Diffraction effects will bring about more difficulties in actuating resonators,which are electrostatically actuated ones with sub-micrometer or nanometer dimensions,and in detecting the frequency of the resonator by o...Diffraction effects will bring about more difficulties in actuating resonators,which are electrostatically actuated ones with sub-micrometer or nanometer dimensions,and in detecting the frequency of the resonator by optical detection.To avoid the effects of diffraction,a new type of nanoelectromechanical systems（NEMS） resonators is fabricated and actuated to oscillate.As a comparison,a doubly clamped silicon beam is also fabricated and studied.The smallest width and thickness of the resonators are 180 and 200 nm,respectively.The mechanical oscillation responses of these two kinds of resonators are studied experimentally.Results show that the resonant frequencies are from 6.8 to 20 MHz,much lower than the theoretical values.Based on the simulation,it is found that over-etching is one of the important factors which results in lower frequencies than the theoretical values.It is also found that the difference between resonance frequencies of two types of resonators decreases with the increase in beam length.The quality factor is improved greatly by lowering the pressure in the sample chamber at room temperature.展开更多
In order to realize automatic tracking drift of resonance frequency of ultrasonic vibration system with high power and high quality factor Q, adaptive fuzzy control was studied with a self-fabricated ultrasonic plasti...In order to realize automatic tracking drift of resonance frequency of ultrasonic vibration system with high power and high quality factor Q, adaptive fuzzy control was studied with a self-fabricated ultrasonic plastic welding machine. At first, relations between amplitude of vibration and frequency as well as main loop current and amplitude of vibration were analyzed. From this analysis, we deduced that frequency tracking process of the vibration system can be concluded as an optimizing problem of one dimensional fluctuant extremum of main loop current in vibration system. Then a method of self-optimizing fuzzy control, used for the realization of automatic frequency tracking in vibration system, is presented on the basis of serf-optimizing adaptive control approach and fuzzy control approach. The result of experiments shows that the fuzzy self-optimizing method can solve the problem of tracking frequency drift very well. Response time of tracking in the system is less than 50 ms, which basically meets the requirements of frequency tracking in ultrasonic plastic welding machine.展开更多
We present a method to increase the sum-frequency （SF） outputs in dielectric/antiferromagnet（AF）/Ag sandwich structures for a fixed input power. Two incident waves simultaneously illuminate the upper surface, one ...We present a method to increase the sum-frequency （SF） outputs in dielectric/antiferromagnet（AF）/Ag sandwich structures for a fixed input power. Two incident waves simultaneously illuminate the upper surface, one is oblique and the other is normal to it. Numerical calculations based on the SiO2/MnF2/Ag and ZnF2/MnF2/Ag structures show that the SF outputs on the upper film increase a few times as compared to those of a single AF film when the thickness of the AF film is one-quarter of the vacuum wavelength. Moreover, the SF outputs generated near the higher resonant frequency will be higher than those obtained near the lower resonant frequency. An optimum AF film thickness is achieved through investigating its effect on the SF outputs in the two different dielectric sandwich structures.展开更多
The small-current grounding fault in distribution network is hard to be located because of its weak fault features.To accurately locate the faults,the transient process is analyzed in this paper.Through the study we t...The small-current grounding fault in distribution network is hard to be located because of its weak fault features.To accurately locate the faults,the transient process is analyzed in this paper.Through the study we take that the main resonant frequency and its corresponding component is related to the fault distance.Based on this,a fault location method based on double-end wavelet energy ratio at the scale corresponding to the main resonant frequency is proposed.And back propagation neural network(BPNN)is selected to fit the non-linear relationship between the wavelet energy ratio and fault distance.The performance of this proposed method has been verified in different scenarios of a simulation model in PSCAD/EMTDC.展开更多
Characteristics of a single-feed dual-frequency bow-tie microstrip antenna are studied. By using the variation method, simple formulas for resonant frequencies of the bow-tie microstrip antenna are derived. It is show...Characteristics of a single-feed dual-frequency bow-tie microstrip antenna are studied. By using the variation method, simple formulas for resonant frequencies of the bow-tie microstrip antenna are derived. It is shown that the dual-frequency ratio can be controlled easily by choosing the parameters of the antenna. This design gives compact antenna size and simple antenna structure. Experimental results are presented, verifying the validity of the design.展开更多
This paper investigates the resonant frequencies of the massless scalar field in the near extremal Kerr-like black-brane spacetime. It is shown that the different angular quantum number will present different resonant...This paper investigates the resonant frequencies of the massless scalar field in the near extremal Kerr-like black-brane spacetime. It is shown that the different angular quantum number will present different resonant frequencies. It is also shown that the real part of the resonant frequencies increases as the compact dimensions parameter μi increases, but the magnitude of the imaginary part decreases as μi increases.展开更多
LC circuit resonance frequency measurement often requires the use of professional analysis instruments such as LCR meters,vector network analyzers,but currently such instruments on the market are expensive,and it is d...LC circuit resonance frequency measurement often requires the use of professional analysis instruments such as LCR meters,vector network analyzers,but currently such instruments on the market are expensive,and it is difficult for non-professional institute personnel to access.Here comes unnecessary trouble.In view of this situation,a test method for measuring the resonance frequency using only a digital storage oscilloscope is proposed.Using the impulse signal to obtain the system response,the response waveform period can be observed through the oscilloscope.展开更多
The modelling and determination of the geometric parameters of a solar cell are important data, which influence the evaluation of its performance under specific operating conditions, as well as its industrial developm...The modelling and determination of the geometric parameters of a solar cell are important data, which influence the evaluation of its performance under specific operating conditions, as well as its industrial development for a low cost. In this work, an n+/p/p+ crystalline silicon solar cell is studied under monochromatic illumination in modulation and placed in a constant magnetic field. The minority carriers’ diffusion coefficient (<em>D</em>(<em>ω</em>, <em>B</em>), in the (<em>p</em>) base leads to maximum values (Dmax) at resonance frequencies (<em>ωr</em>). These values are used in expressions of AC minority carriers recombination velocity (Sb(Dmax, H)) in the rear of the base, to extract the optimum thickness while solar cell is subjected to these specific conditions. Optimum thickness modelling relationships, depending respectively on Dmax, <em>ωr</em> and <em>B</em>, are then established, and will be data for industrial development of low-cost solar cells for specific use.展开更多
We study the dynamic behavior of a quartz crystal resonator （QCR） in thickness-shear vibrations with the upper surface covered by an array of micro-beams （MBs） under large deflection. Through taking into account t...We study the dynamic behavior of a quartz crystal resonator （QCR） in thickness-shear vibrations with the upper surface covered by an array of micro-beams （MBs） under large deflection. Through taking into account the continuous conditions of shear force and bending moment at the interface of MBs/resonator, dependences of frequency shift of the compound QCR system versus material parameter and geometrical parameter are illustrated in detail for nonlinear and linear vibrations. It is found that the frequency shift produces a little right （left） translation for increasing elastic modulus （length/radius ratio） of MBs. Moreover, the frequency right （left） translation distance caused by nonlinear deformation becomes more serious in the second-order mode than in the first-order one,展开更多
基金supported by the National Natural Science Foundation of China(10772086 and 10727201)the National University of Singapore(R-265-000-140-112)
文摘This paper presents a novel non-contact method for evaluating the resonant frequency of a microstructure, Firstly, the microstructure under test is excited by ultrasonic waves. This excitation method does not impose any undefined load on the specimen like the electrostatic excitation and also this is the first actual use of ultrasonic wave for exciting a microstructure in the literature. Secondly, the amplitudes of the microstructure are determined by image edge detection using a Mexican hat wavelet transform on the vibrating images of the microstructure. The vibrating images are captured by a CCD camera when the microstructure is vibrated by ultrasonic waves at a series of discrete high frequencies （〉30 kHz）. Upon processing the vibrating images, the amplitudes at various excitation frequencies are obtained and an amplitude-frequency spectrum is obtained from which the resonant frequency is subsequently evaluated. A micro silicon structure consisting of a perforated plate （192 × 192 μm） and two cantilever beams （76 × 43 μm） which is about 4 μm thickness is tested. Since laser interferometry is not required, thermal effects on a test object can be avoided. Hence, the setup is relatively simple. Results show that the proposed method is a simple and effective approach for evaluating the dynamic characteristics of microstructures.
基金supported in part by the National Natural Science Foundation of China under Grants 51877093 and 51707079in part by the National Key Research and Development Program of China under Grant 2018YFE0100200in part by the Key Technical Innovation Program of Hubei Province under Grant 2019AAA026.
文摘To optimize the efficiency of the linear compressor,its operating frequency must be controlled equal to the system resonant frequency.The traditional resonant frequency tracking control algorithm relies on the steady state characteristics of the system,which suffers from slow convergence speed,low accuracy and slow system response.In order to solve these problems,a novel resonant frequency tracking control for linear compressor based on model reference adaptive system(MRAS)is proposed in this paper,and the parameter adaptive rate is derived by the Popov's hyperstability theory,so that the system resonant frequency can be directly calculated through the parameter adaptive rate.Furthermore,the traditional algorithm needs to calculate the piston stroke signal by integrating the back-EMF,which has the problem of integral drift.The algorithm proposed in this paper only needs the velocity signal,and the accuracy of the velocity calculation can be ensured by utilizing the self-adaptive band-pass filter(SABPF),thereby greatly improving the accuracy of the resonance frequency calculation.Simulation results verify the effectiveness of the proposed algorithm.
文摘The introduction of machine learning (ML) in the research domain is a new era technique. The machine learning algorithm is developed for frequency predication of patterns that are formed on the Chladni plate and focused on the application of machine learning algorithms in image processing. In the Chladni plate, nodes and antinodes are demonstrated at various excited frequencies. Sand on the plate creates specific patterns when it is excited by vibrations from a mechanical oscillator. In the experimental setup, a rectangular aluminum plate of 16 cm x 16 cm and 0.61 mm thickness was placed over the mechanical oscillator, which was driven by a sine wave signal generator. 14 Chladni patterns are obtained on a Chladni plate and validation is done with modal analysis in Ansys. For machine learning, a large number of data sets are required, as captured around 200 photos of each modal frequency and around 3000 photos with a camera of all 14 Chladni patterns for supervised learning. The current model is written in Python language and model has one convolution layer. The main modules used in this are Tensor Flow Keras, NumPy, CV2 and Maxpooling. The fed reference data is taken for 14 frequencies between 330 Hz to 3910 Hz. In the model, all the images are converted to grayscale and canny edge detected. All patterns of frequencies have an almost 80% - 99% correlation with test sample experimental data. This approach is to form a directory of Chladni patterns for future reference purpose in real-life application. A machine learning algorithm can predict the resonant frequency based on the patterns formed on the Chladni plate.
基金the Natural Science Foundation of Inner Mongolia of China(Grant No.2019MS01021)the Research Program of Science and Technology at Universi-ties of Inner Mongolia Autonomous Region,China(Grant No.NJZY21454)the Theoretical Physics Discipline De-velopment and Communication Platform of Inner Mongolia University(Grant No.12147216).
文摘The dependences of spin wave resonance(SWR)frequency on the surface anisotropy field,interface exchange coupling,symmetry,biquadratic exchange(BQE)interaction,film thickness,and the external magnetic field in bilayer ferromagnetic films are theoretically analyzed by employing the linear spin wave approximation and Green’s function method.A remarkable increase of SWR frequency,except for energetically lower two modes,can be obtained in our model that takes the BQE interaction into account.Again,the effect of the external magnetic field on SWR frequency can be increased by increasing the biquadratic to interlayer exchange ratio.It has been identified that the BQE interaction is of utmost importance in improving the SWR frequency of the bilayer ferromagnetic films.In addition,for bilayer ferromagnetic films,the frequency gap between the energetically highest mode and lowest mode is found to increase by increasing the biquadratic to interlayer exchange ratio and film thickness and destroying the symmetry of the system.These results can be used to improve the understanding of magnetic properties in bilayer ferromagnetic films and thus may have prominent implications for future magnetic devices.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51901163 and 12104171)the Fundamental Research Funds for the Central Universities(Grant No.2021XXJS025).
文摘The flexible materials exhibit more favorable properties than most rigid substrates in flexibility,weight saving,mechanical reliability,and excellent environmental toughness.Particularly,flexible graphene film with unique mechanical properties was extensively explored in high frequency devices.Herein,we report the characteristics of structure and magnetic properties at high frequency of Co2FeAl thin film with different thicknesses grown on flexible graphene substrate at room temperature.The exciting finding for the columnar structure of Co2FeAl thin film lays the foundation for excellent high frequency property of Co2FeAl/flexible graphene structure.In-plane magnetic anisotropy field varying with increasing thickness of Co2FeAl thin film can be obtained by measurement of ferromagnetic resonance,which can be ascribed to the enhancement of crystallinity and the increase of grain size.Meanwhile,the resonance frequency which can be achieved by the measurement of vector network analyzer with the microstrip method increases with increasing thickness of Co2FeAl thin film.Moreover,in our case with graphene film,the resonance magnetic field is quite stable though folded for twenty cycles,which demonstrates that good flexibility of graphene film and the stability of high frequency magnetic property of Co2FeAl thin film grown on flexible graphene substrate.These results are promising for the design of microwave devices and wireless communication equipment.
基金Project supported by the National Nature Science Foundation of China(Grant No.51490673)the National Key R&D Program of China(Project ID:2016YFE0200100).
文摘The objective of this study is to develop a simple tool for predicting the resonant frequency of the piston mode wave oscillation in a moonpool or a narrow gap between twin floating barges.Based on the dynamic analysis and the domain-decomposition,a linear harmonic oscillator model for the fluid oscillation in a confined space is formulated,which immediately leads to an explicit dynamic solution for the resonant frequency.In the model,it is assumed that the water depth is equal to or greater than a critical value dependent on the ratio of the draft to the breadth of the floating body.The predicted resonant frequencies are compared with the numerical results of the linear potential model and the viscous fluid model,the semi-analytical potential solutions and the experimental measurements.Good agreements are observed for a wide range of geometric parameters of the moonpool and the narrow gap of either sharp or round edge shapes.The present dynamic method is also applied to predict the resonant frequency of the piston mode oscillation in the gap between a floating body and a vertical wall with a reasonable success.
基金supported by the Young Scientists Ftmd of the National Natural Science Foundation of China(51005241)the Postdoctoral Science and Technology Activities Preferred Financing Project in Hubei Province
文摘A flextensional transducer with an Omega shape and its algorithmic method of the resonant frequency and the shape functions are suggested. The Omega transducer is separated into four parts treated respectively as a thin shell of revolution and the theories of thin shells of revolution and piezoelectricity are used to obtain the energy functional of each part so that the sum of the energy functionals of the four parts is the energy functional of the whole Omega transducer. By substituting the shape functions with undetermined coefi3cients and the geo- metrical boundary conditions into the energy functional of the Omega transducer, the resonant frequency of the Omega transducer is firstly determined with the Rayleigh-Ritz method. With the gotten resonant frequency, the constant coefficients of the shape functions are following solved through the Rayleigh-Ritz partial differential equations and the geometrical boundary condition equations. The solving method of the resonant frequency and the shape functions is also extended to the cymbal transducer. Such an analytical method is verified to be feasible by the results of the finite element analysis and experiments. The research indicates that （1） The radial vibration of the piezoelectric ceramic is in phase with the longitudinal vibration of the top of metal cap, and it cut down the reversed phase component in the sound field. The Omega transducer can be a low frequency transducer. （2） The determination method of the resonant frequency and the shape functions give a solution to the optimum designs of the Omega transducer and the cymbal transducer. （3） The determination method of the resonant fi＇equency and the shape functions can also be used in other flextensional transducers or other structures which are composed of thin shells of revolution, so it is universal.
基金Project supported by the National Natural Science Foundation of China (No.50806065)the Research Fund for the Doctoral Program of Higher Education of China (No.200803351053)
文摘Gas-liquid coupling oscillation is a novel approach to reducing the resonant frequency and to elevating the pressure amplitude of a thermoacoustic engine.If a thermoacoustic engine is used to drive low-frequency pulse tube refrigerators,the frequency matching between the thermoacoustic engine and the refrigerator plays an important role.Based on an acoustic-electric analogy,a lumped parameter model is proposed to estimate the resonant frequency of a standing-wave thermoacoustic engine with gas-liquid coupling oscillation.Furthermore,a simplified lumped parameter model is also developed to reduce the computation complexity.The resonant frequency dependence on the mean pressure,the gas space volume,and the water column length is computed and analyzed.The impact of different working gases on the resonant frequency is also discussed.The effectiveness of the models is validated by comparing the computed results with the experimental data of the gas-liquid coupling oscillation system.An increase in the mean working pressure can lead to a rise in the resonant frequency,and a lower resonant frequency can be achieved by elongating the liquid column.In comparison with nitrogen and argon,carbon dioxide can realize a lower frequency due to a smaller specific heat ratio.
文摘In this paper, an analytical model for computing the resonant frequency of the gap-coupled ring microstrip patch antennas is developed. The analytical model is based upon the cavity model along with circuit theory. Using the field expressions and boundary conditions, the transcendental equation for the structure is developed. The analytically computed results are compared with the simulated results. The simulation work is carried out by using computer simulation technology(CST) microwave studio simulator.The comparison between simulated and computed results shows good agreement.
基金supported by the National Basic Research Program of China (Grant No. 2010CB923101)the National Natural Science Foundation of China (Grant Nos. 61227015 and 61121064)
文摘We report on the generation of self-oscillations from a continuously pumped singly resonant frequency doubler based on a periodically poled potassium titanyl phosphate crystal （PPKTP）. The sustained square-wave and staircase curve of self-oscillations are obtained when the incident pump powers are below and above the threshold of subharmonic-pumped parametric oscillation （SPO）, respectively. The self-oscillations can be explained by the competition between the phase shifts induced by cascading nonlinearity and thermal effect, and the influence of fundamental nonlinear phase shift by the generation of SPO. The simulation results are in good agreement with the experiment data.
基金supported by the National High-Tech R & D Program (863) of China (No. 2008AA042602)the Fundamental Research Funds for the Central Universities, China (No. KYJD09035)
文摘Proportional integrator (PI) is always adopted in the resonant frequency servo loop in a resonator micro optic gyro (RMOG). The oscillation phenomenon is observed when adjusting the loop gain surpassing a threshold. This phenomenon limits system performance on step response speed and residual error. Based on the experiment system, a simulation model was set up. Further analysis shows that the threshold gain is related to the system loop filter setting and the loop delay. The traditional PI frequency servo loop technique in the RMOG system cannot keep up with the environment's disturbance quickly enough, which leads to a large residual error. A compensating method is proposed to optimize the tracking performance, solve the oscillation problem, and speed up the system response. Simulation and experiment results show that the compensated system is superior in performance. It has less residual error in the stable state and is 10 times quicker than the uncompensated system on the step response.
基金The National High Technology Research and Development Program of China(863 Program)(No.2007AA04Z301)
文摘Diffraction effects will bring about more difficulties in actuating resonators,which are electrostatically actuated ones with sub-micrometer or nanometer dimensions,and in detecting the frequency of the resonator by optical detection.To avoid the effects of diffraction,a new type of nanoelectromechanical systems（NEMS） resonators is fabricated and actuated to oscillate.As a comparison,a doubly clamped silicon beam is also fabricated and studied.The smallest width and thickness of the resonators are 180 and 200 nm,respectively.The mechanical oscillation responses of these two kinds of resonators are studied experimentally.Results show that the resonant frequencies are from 6.8 to 20 MHz,much lower than the theoretical values.Based on the simulation,it is found that over-etching is one of the important factors which results in lower frequencies than the theoretical values.It is also found that the difference between resonance frequencies of two types of resonators decreases with the increase in beam length.The quality factor is improved greatly by lowering the pressure in the sample chamber at room temperature.
基金Sponsored by the Natural Science Foundation of Shanghai Education Committee(Grant No.05LZ13)Shanghai Leading Academic Discipline Project(Grant No. P1303)Shanghai Elitist Project(Grant No.04YQHB126)
文摘In order to realize automatic tracking drift of resonance frequency of ultrasonic vibration system with high power and high quality factor Q, adaptive fuzzy control was studied with a self-fabricated ultrasonic plastic welding machine. At first, relations between amplitude of vibration and frequency as well as main loop current and amplitude of vibration were analyzed. From this analysis, we deduced that frequency tracking process of the vibration system can be concluded as an optimizing problem of one dimensional fluctuant extremum of main loop current in vibration system. Then a method of self-optimizing fuzzy control, used for the realization of automatic frequency tracking in vibration system, is presented on the basis of serf-optimizing adaptive control approach and fuzzy control approach. The result of experiments shows that the fuzzy self-optimizing method can solve the problem of tracking frequency drift very well. Response time of tracking in the system is less than 50 ms, which basically meets the requirements of frequency tracking in ultrasonic plastic welding machine.
基金Project supported by the Young Academic Back-bone of Education Commission of Heilongjiang Province,China(Grant Nos.1251G030 and12521154)the National Natural Science Foundation of China(Grant Nos.11104050,11204056,and 11074061)
文摘We present a method to increase the sum-frequency （SF） outputs in dielectric/antiferromagnet（AF）/Ag sandwich structures for a fixed input power. Two incident waves simultaneously illuminate the upper surface, one is oblique and the other is normal to it. Numerical calculations based on the SiO2/MnF2/Ag and ZnF2/MnF2/Ag structures show that the SF outputs on the upper film increase a few times as compared to those of a single AF film when the thickness of the AF film is one-quarter of the vacuum wavelength. Moreover, the SF outputs generated near the higher resonant frequency will be higher than those obtained near the lower resonant frequency. An optimum AF film thickness is achieved through investigating its effect on the SF outputs in the two different dielectric sandwich structures.
基金supported by National Key R&D Program of China(2017YFB0902800)Science and 333 Technology Project of State Grid Corporation of China(52094017003D).
文摘The small-current grounding fault in distribution network is hard to be located because of its weak fault features.To accurately locate the faults,the transient process is analyzed in this paper.Through the study we take that the main resonant frequency and its corresponding component is related to the fault distance.Based on this,a fault location method based on double-end wavelet energy ratio at the scale corresponding to the main resonant frequency is proposed.And back propagation neural network(BPNN)is selected to fit the non-linear relationship between the wavelet energy ratio and fault distance.The performance of this proposed method has been verified in different scenarios of a simulation model in PSCAD/EMTDC.
文摘Characteristics of a single-feed dual-frequency bow-tie microstrip antenna are studied. By using the variation method, simple formulas for resonant frequencies of the bow-tie microstrip antenna are derived. It is shown that the dual-frequency ratio can be controlled easily by choosing the parameters of the antenna. This design gives compact antenna size and simple antenna structure. Experimental results are presented, verifying the validity of the design.
基金Project supported by the National Natural Science Foundation of China (Grant No 10675045)the Foundation for the Author of National Excellent Doctoral Dissertation of China (Grant No 200317)
文摘This paper investigates the resonant frequencies of the massless scalar field in the near extremal Kerr-like black-brane spacetime. It is shown that the different angular quantum number will present different resonant frequencies. It is also shown that the real part of the resonant frequencies increases as the compact dimensions parameter μi increases, but the magnitude of the imaginary part decreases as μi increases.
文摘LC circuit resonance frequency measurement often requires the use of professional analysis instruments such as LCR meters,vector network analyzers,but currently such instruments on the market are expensive,and it is difficult for non-professional institute personnel to access.Here comes unnecessary trouble.In view of this situation,a test method for measuring the resonance frequency using only a digital storage oscilloscope is proposed.Using the impulse signal to obtain the system response,the response waveform period can be observed through the oscilloscope.
文摘The modelling and determination of the geometric parameters of a solar cell are important data, which influence the evaluation of its performance under specific operating conditions, as well as its industrial development for a low cost. In this work, an n+/p/p+ crystalline silicon solar cell is studied under monochromatic illumination in modulation and placed in a constant magnetic field. The minority carriers’ diffusion coefficient (<em>D</em>(<em>ω</em>, <em>B</em>), in the (<em>p</em>) base leads to maximum values (Dmax) at resonance frequencies (<em>ωr</em>). These values are used in expressions of AC minority carriers recombination velocity (Sb(Dmax, H)) in the rear of the base, to extract the optimum thickness while solar cell is subjected to these specific conditions. Optimum thickness modelling relationships, depending respectively on Dmax, <em>ωr</em> and <em>B</em>, are then established, and will be data for industrial development of low-cost solar cells for specific use.
基金supported by the National Natural Science Foundation of China(11272127 and 51435006)the Research Fund for the Doctoral Program of Higher Education of China(20130142110022)
文摘We study the dynamic behavior of a quartz crystal resonator （QCR） in thickness-shear vibrations with the upper surface covered by an array of micro-beams （MBs） under large deflection. Through taking into account the continuous conditions of shear force and bending moment at the interface of MBs/resonator, dependences of frequency shift of the compound QCR system versus material parameter and geometrical parameter are illustrated in detail for nonlinear and linear vibrations. It is found that the frequency shift produces a little right （left） translation for increasing elastic modulus （length/radius ratio） of MBs. Moreover, the frequency right （left） translation distance caused by nonlinear deformation becomes more serious in the second-order mode than in the first-order one,
