The rare earth complex Eu(TTA) 3 was successfully encapsulated into MCM 41 mesoporous molecular sieve by the addition of the complex into the sol gel mixture for the synthesis of MCM 41 mesoporous material under micro...The rare earth complex Eu(TTA) 3 was successfully encapsulated into MCM 41 mesoporous molecular sieve by the addition of the complex into the sol gel mixture for the synthesis of MCM 41 mesoporous material under microwave radiation. The as synthesized MCM 41 hosted Eu(TTA) 3 mesophase was confirmed to possess hexagonally ordered mesostructure and a uniform crystal size of about 30 nm with XRD and HRTEM techniques. Moreover, the IR spectrum, photoluminescence effect and fluorescence lifetime of the Eu(TTA) 3/MCM 41 hybrid were also studied. An increase in Stokes’ shift and no change in luminescence lifetime were observed to the resultant mesophase in comparison with Eu(TTA) 3 in ethanol solution.展开更多
Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800 ℃.The grain size,crystal size,and crystallinity of ZnWO4 particles increased with the increase of...Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800 ℃.The grain size,crystal size,and crystallinity of ZnWO4 particles increased with the increase of calcination temperature and prolonging calcination time.The photocatalytic activity was measured for the degradation of an aqueous Rhodamine-B(RhB)solution and gaseous formaldehyde(FAD).With the increase of calcination temperature and time,the activities increased to a maximum and then decreased.ZnWO4 photocatalyst prepared at 550 ℃ for 10 h showed the highest activity,which is similar to the photocatalytic activity of P25TiO2 for the degradation of gaseous FAD.High crystallinity,large surface area,and good dispersion are responsible for the high photocatalytic performance of the prepared ZnWO4.展开更多
Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were...Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.展开更多
LiMn_2O_4 and LiNi_xAlyMn_(2-x-y)O_4(x= 0.50;y = 0.05-0.50) powders have been synthesized via facile solgel method using Behenic acid as active cheiating agent.The synthesized samples are subjected to physical charact...LiMn_2O_4 and LiNi_xAlyMn_(2-x-y)O_4(x= 0.50;y = 0.05-0.50) powders have been synthesized via facile solgel method using Behenic acid as active cheiating agent.The synthesized samples are subjected to physical characterizations such as thermo gravimetric analysis(TG/DTA),X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FT-IR),field-emission scanning electron microscopy(FESEM),transmission electron microscopy(TEM) and electrochemical studies viz.,galvanostatic cycling properties,electrochemical impedance spectroscopy(EIS) and differential capacity curves(dQ/dE).Finger print XRD patterns of LiMn_2O_4 and LiNi_xAl_yMn_(2-x-y)O_4 fortify the high degree of crystallinity with better phase purity.FESEM images of the undoped pristine spinel illustrate uniform spherical grains surface morphology with an average particle size of 0.5 μm while Ni doped particles depict the spherical grains growth(50nm) with ice-cube surface morphology.TEM images of the spinel LiMn_2O_4 shows the uniform spherical morphology with particle size of(100 nm) while low level of Al-doping spinel(LiNio.5Alo.05Mn1.45O4) displaying cloudy particles with agglomerated particles of(50nm).The LiMn_2O_4 samples calcined at 850℃ deliver the discharge capacity of 130 mAh/g in the first cycle corresponds to 94%coiumbic efficiency with capacity fade of 1.5 mAh/g/cycle over the investigated 10 cycles.Among all four dopant compositions investigated,LiNi_(0.5)Al_(0.05)Mn_(1.45)O_4 delivers the maximum discharge capacity of 126 mAh/g during the first cycle and shows the stable cycling performance with low capacity fade of 1 mAh/g/cycle(capacity retention of 92%) over the investigated 10 cycles.Electrochemical impedance studies of spinel LiMn_2O_4 and LiNi_(0.5)Al_(0.05)Mn_(1.45)O_4 depict the high and low real polarization of 1562 and 1100 Ω.展开更多
Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kind...Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kinds of BaTiO3 ceramic inks were prepared by mechanical mixing and sol-gel methods,respectively.The effect of preparation parameters,such as quantity of polyacrylic acid(PAA)and solid content,on physicochemical and rheologic properties of the ceramic inks was investigated.The results show that they satisfy the requirements of continuous ink-jet printing.The appearances of printed dots and single printed layers were observed by SEM.The SEM images indicate that dots printed with mixing method ink are in ring shape,and dots printed with sol-gel method ink are in pancake shape,so the printed layer surface with the latter ink is smoother.The causes of these phenomena were discussed.展开更多
A series of red-emitting Ca2-xAl2SiO7:xEu3+(x = 1 mol.%-10 mol.%) phosphors were synthesized by the sol-gel method.The effects of annealing temperature and doping concentration on the crystal structure and luminescenc...A series of red-emitting Ca2-xAl2SiO7:xEu3+(x = 1 mol.%-10 mol.%) phosphors were synthesized by the sol-gel method.The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2Al2SiO7:Eu3+ phosphors were investigated.X-ray diffraction(XRD) profiles showed that all peaks could be attributed to the tetragonal Ca2Al2SiO7 phase when the sample was annealed at 1000℃.Scanning electron microscopy(SEM) micrographs indicate that the phosphors have an irregularly rounded morphology with particles of about 200 nm.Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu3+-O2-and f-f transitions within the 4f6 configuration of Eu3+ ions,respectively.Emission spectra implied that the red luminescence could be attributed to the transitions from the 5D0 excited level to the 7FJ(J = 0,1,2,3,4) levels of Eu3+ ions with the main electric dipole transition 5D0→7F2(618 and 620 nm),and Eu3+ ions prefer to occupy a lower symmetry site in the crystal lattice.Moreover,the photoluminescence(PL) intensity was strongly dependent on both the sintering temperature and doping concentration,and the highest PL intensity was observed at an Eu3+ concentration x = 7 mol.% after annealing at 1100℃.The obtained Ca2Al2SiO7:Eu3+ phosphor may have potential application for the red lamp phosphor.展开更多
Nanocrystal SmBO3 powders were synthesized by nitrate-citrate sol-gel combustion method. The phase evolution, morphologies and absorbency of the synthesized powders were characterized by X-ray diffraction (XRD), Field...Nanocrystal SmBO3 powders were synthesized by nitrate-citrate sol-gel combustion method. The phase evolution, morphologies and absorbency of the synthesized powders were characterized by X-ray diffraction (XRD), Field emission scanning electronic microscope (FESEM), Fourier transform infrared spectroscopy (FTIR) and UV-3101PC spectrophotometer (UVPC), respectively. XRD and FESEM results showed that pure SmBO3 phase was obtained at 750 °C, with an average original particle size of about 100 nm. FTIR showed that there were apparently concentrated absorbent peaks between 500 and 1400 cm-1. Moreover, the reflectivity of the powders apparently decreased at the wavelength between 1.05 and 1.15 μm. Therefore, SmBO3 might be a kind of absorbent material for infrared laser.展开更多
Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show ...Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show the hexagonal wurtzite polycrystalline structure and that the sodium incorporation leads to the change in the structural characteristics of ZnO films.The SEM observations show that the surface morphology of the films is affected by the sodium incorporation.The transmission spectra show that the average transmittance of the films is above 85% in the visible range.The absorption edge initially blue-shifts and then red-shifts with the increase of Na doping content.The optical constants of these films were calculated using transmission spectra.Refractive indices of the films in the visible range decrease at first and then increase with increasing Na doping content.展开更多
Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffract...Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results of XRD show that the single crystalline phase is α-SrAl2O4. According to the observation of SEM, the particles of the samples are needle-like. Compared with the samples synthesized by solid state reaction, the grain size of the sol-gel method is to nanometer grade. A clear blue shift occurs in the excitation and emission spectra. The blue shift in nanocrystalline SrAl2O4∶Eu, Dy phosphor can be attributed to the quantum-size-effect of the luminescent particles.展开更多
The three-way catalysts (TWCs) promoters Ce0.6Zr0.4-xTbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x=0.05 to x=0.15 favors an increase of ...The three-way catalysts (TWCs) promoters Ce0.6Zr0.4-xTbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x=0.05 to x=0.15 favors an increase of surface area from 66.8 to 80.4 m2·g-1 compared with the undoped sample Ce0.60Zr0.40O2 65.1 m2·g-1 after calcination at 650 ℃. Transmission electron microscopy (TEM) observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce4+ and Tb3+, and Zr existed in the form of Zr4+ on the surface of the samples. The doped samples were homogenous in composition; the introduction of Tb into the CeO2-ZrO2 promoters resulted in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.展开更多
Highly ordered nanowire/tube arrays of Ni0.5Zn0.5Fe2O4 were fabricated by the sol-gel method in the pores of anodic alu- mina membrane (AAM). Whether nanowires or nanotubes were fabricated depends on immersion time. T...Highly ordered nanowire/tube arrays of Ni0.5Zn0.5Fe2O4 were fabricated by the sol-gel method in the pores of anodic alu- mina membrane (AAM). Whether nanowires or nanotubes were fabricated depends on immersion time. The immersion time was 15-40 s for nanotubes and over 60 s for nanowires. The topography and crystalline structure of the nanowire arrays were character- ized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). It was found that the length and diameter of the Ni0.5Zn0.5Fe2O4 nanowires are related to the thickness of the AAM and the diameter of the pores. The results indicated that the Ni0.5Zn0.5Fe2O4 nanowires are uniform and parallel to each other.展开更多
Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum a...Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466 nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8 h.展开更多
M-type Ba hexaferrites were successfully synthesized by sol-gel method. Several synthesizing factors, such as pH value, citric acid/metal ion ratio, and dispersion agent were mainly discussed. Fine and pure powders of...M-type Ba hexaferrites were successfully synthesized by sol-gel method. Several synthesizing factors, such as pH value, citric acid/metal ion ratio, and dispersion agent were mainly discussed. Fine and pure powders of BaFe12O19 were optimally synthesized under the conditions of the pH value is 7 and citric acid/metal ion ratio is 3. The X-ray diffraction analysis demonstrates that no impurity is observed in the synthesized powders after presintered at 450 ℃ and calcinated at 1100 ℃. SEM observations indicate that the size of the synthesized BaFe12O19 powders is small and uniform distribution. It can also be learned from SEM that the co-synthesizing sol-gel method can be in favor of the formation of finer particles.展开更多
Two series of perovskite-type oxides with composition (La1-x)SrxFeO3（x≤0.8）and La1-xSrxFe1-yCoyO3（x=0.2; y=0.2, 0.4）powder productions were synthesized by EDTA complexing sol-gel method. The products were charact...Two series of perovskite-type oxides with composition (La1-x)SrxFeO3（x≤0.8）and La1-xSrxFe1-yCoyO3（x=0.2; y=0.2, 0.4）powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method（N2 adsorption）and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.展开更多
Nanometer Al2O3 is one of new types of functional materials with broad application and development prospects in the future. The basic principle and ways of nanometer Al2O3 fabricated using sol-gel technique were intro...Nanometer Al2O3 is one of new types of functional materials with broad application and development prospects in the future. The basic principle and ways of nanometer Al2O3 fabricated using sol-gel technique were introduced, and the factors affecting nanometer Al2O3 fabricated using sol-gel method were analyzed. The progress in research on nanometer Al2O3 and the application fields of nanometer Al2O3 were reviewed. The existing problems and the problems prospect for nanometer Al2O3 were pointed out.展开更多
The CaCu3Ti4O12 xerogels,powders and ceramics were prepared through the sol-gel method using two kinds of organic acid(decanoic acid and decanedioic acid).The xerogels,powders and ceramics were characterized by the me...The CaCu3Ti4O12 xerogels,powders and ceramics were prepared through the sol-gel method using two kinds of organic acid(decanoic acid and decanedioic acid).The xerogels,powders and ceramics were characterized by the methods of TG-DTG,FT-IR,XRD,SEM and TEM.The dielectric properties of the ceramics were also measured.The results indicated that the powders calcined at 850°C for 2h are both nanometer scale particles.After sintering,the ceramics mainly consist of the CaCu3Ti4O12 phase.Compared with the powders prepared using monoacid,the particle size of the powders prepared using diacid obviously increases,and the grain size,the relative density and the whole permittivity of the ceramics increase as well.Specially,the ceramic prepared using decanedioic acid has higher relative density(97.3%),dielectric constant(316 808)and lower dielectric loss(0.242 5)at 30°C(10kHz)展开更多
The effect of different annealing temperatures on the structure, morphology, and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated. Zinc-oxide thin films were coated on qua...The effect of different annealing temperatures on the structure, morphology, and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated. Zinc-oxide thin films were coated on quartz glass substrates by dip coating. Zinc nitrate, absolute ethanol, and citric acid were used as precursor, solvent, and chelating agent, respectively. The results show that ZnO films derived from zinc-citrate have lower crystallization temperature (below 400°C),and that the crystal structure is wurtzite. The films, treated over 500°C, consist of nano-particles and show to be porous at 600°C. The particle size of the film increases with the increase of the annealing temperature. The largest particle size is 60 nm at 600°C. The optical transmittances related to the annealing temperatures become 90% higher in the visible range. The film shows a starting absorption at 380 nm, and the optical band-gap of the thin film (fired at 500°C) is 3.25 eV and close to the intrinsic band-gap of ZnO (3.2 eV).展开更多
The effect of Al-substitution on the electrochemical performances of Li3V2(PO4)3 cathode materials was studied.Samples with stoichiometric proportion of Li3AlxV2-x(PO4)3(x=0,0.05,0.10)were prepared by adding Al(NO3)3 ...The effect of Al-substitution on the electrochemical performances of Li3V2(PO4)3 cathode materials was studied.Samples with stoichiometric proportion of Li3AlxV2-x(PO4)3(x=0,0.05,0.10)were prepared by adding Al(NO3)3 in the raw materials of Li3V2(PO4)3.The XRD analysis shows that the Al-substituted Li3V2(PO4)3 has the same monoclinic structure as the un-substituted Li3V2(PO4)3.The SEM images show that Al-substituted Li3V2(PO4)3 has regular and uniform particles.The electrochemical measurements show that Al-substitution can improve the rate capability of cathode materials.The Li3Al0.05V1.95(PO4)3 sample shows the best high-rate performance.The discharge capacity at 1C rate is 119 mA·h/g with 30th capacity retention rate about 92.97%.The electrode reaction reversibility and electronic conductivity are enhanced,and the charge transfer resistance decreases through Al-substitution.The improved electrochemical performances of Al-substituted Li3V2(PO4)3 cathode materials offer some favorable properties for their commercial application.展开更多
文摘The rare earth complex Eu(TTA) 3 was successfully encapsulated into MCM 41 mesoporous molecular sieve by the addition of the complex into the sol gel mixture for the synthesis of MCM 41 mesoporous material under microwave radiation. The as synthesized MCM 41 hosted Eu(TTA) 3 mesophase was confirmed to possess hexagonally ordered mesostructure and a uniform crystal size of about 30 nm with XRD and HRTEM techniques. Moreover, the IR spectrum, photoluminescence effect and fluorescence lifetime of the Eu(TTA) 3/MCM 41 hybrid were also studied. An increase in Stokes’ shift and no change in luminescence lifetime were observed to the resultant mesophase in comparison with Eu(TTA) 3 in ethanol solution.
基金Supported by the National Natural Science Foundation of China(Nos.20433010and20571047)Specialized Research Fundfor the Doctoral Program of Higher Education(No.20060003082).
文摘Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800 ℃.The grain size,crystal size,and crystallinity of ZnWO4 particles increased with the increase of calcination temperature and prolonging calcination time.The photocatalytic activity was measured for the degradation of an aqueous Rhodamine-B(RhB)solution and gaseous formaldehyde(FAD).With the increase of calcination temperature and time,the activities increased to a maximum and then decreased.ZnWO4 photocatalyst prepared at 550 ℃ for 10 h showed the highest activity,which is similar to the photocatalytic activity of P25TiO2 for the degradation of gaseous FAD.High crystallinity,large surface area,and good dispersion are responsible for the high photocatalytic performance of the prepared ZnWO4.
基金This work was financially supported by Foundation for Uni-versity Key Teacher by the Ministry of Education, the National Natu-ral Science Foundation of China (No. 50072016) and the Key Re-search Project of the Ministry of Education(No.99087)
文摘Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.
基金support given under the "Brain Pool Program of the Korean Federation of Science and Technology Societies" (KOFST), Republic of South Koreasupported by the Human Resources Development Program (No. 20124010203270) of the Korea Institute of Energy Technology EvaluationPlanning (KETEP) grant funded by the Korea Government Ministry of Trade, Industry and Energy
文摘LiMn_2O_4 and LiNi_xAlyMn_(2-x-y)O_4(x= 0.50;y = 0.05-0.50) powders have been synthesized via facile solgel method using Behenic acid as active cheiating agent.The synthesized samples are subjected to physical characterizations such as thermo gravimetric analysis(TG/DTA),X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FT-IR),field-emission scanning electron microscopy(FESEM),transmission electron microscopy(TEM) and electrochemical studies viz.,galvanostatic cycling properties,electrochemical impedance spectroscopy(EIS) and differential capacity curves(dQ/dE).Finger print XRD patterns of LiMn_2O_4 and LiNi_xAl_yMn_(2-x-y)O_4 fortify the high degree of crystallinity with better phase purity.FESEM images of the undoped pristine spinel illustrate uniform spherical grains surface morphology with an average particle size of 0.5 μm while Ni doped particles depict the spherical grains growth(50nm) with ice-cube surface morphology.TEM images of the spinel LiMn_2O_4 shows the uniform spherical morphology with particle size of(100 nm) while low level of Al-doping spinel(LiNio.5Alo.05Mn1.45O4) displaying cloudy particles with agglomerated particles of(50nm).The LiMn_2O_4 samples calcined at 850℃ deliver the discharge capacity of 130 mAh/g in the first cycle corresponds to 94%coiumbic efficiency with capacity fade of 1.5 mAh/g/cycle over the investigated 10 cycles.Among all four dopant compositions investigated,LiNi_(0.5)Al_(0.05)Mn_(1.45)O_4 delivers the maximum discharge capacity of 126 mAh/g during the first cycle and shows the stable cycling performance with low capacity fade of 1 mAh/g/cycle(capacity retention of 92%) over the investigated 10 cycles.Electrochemical impedance studies of spinel LiMn_2O_4 and LiNi_(0.5)Al_(0.05)Mn_(1.45)O_4 depict the high and low real polarization of 1562 and 1100 Ω.
基金Project(106151)supported by the Major Program of the Ministry of Education of ChinaProject(59842001)supported by the National Natural Science Foundation of China
文摘Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kinds of BaTiO3 ceramic inks were prepared by mechanical mixing and sol-gel methods,respectively.The effect of preparation parameters,such as quantity of polyacrylic acid(PAA)and solid content,on physicochemical and rheologic properties of the ceramic inks was investigated.The results show that they satisfy the requirements of continuous ink-jet printing.The appearances of printed dots and single printed layers were observed by SEM.The SEM images indicate that dots printed with mixing method ink are in ring shape,and dots printed with sol-gel method ink are in pancake shape,so the printed layer surface with the latter ink is smoother.The causes of these phenomena were discussed.
基金supported by the National Natural Science Foundation of China (No. 10874160)the Science and Technology Foundation of Guangdong Province,China (No. 2007173)the Science and Technology Foundation of Jiangmen City, China (No. 2007028)
文摘A series of red-emitting Ca2-xAl2SiO7:xEu3+(x = 1 mol.%-10 mol.%) phosphors were synthesized by the sol-gel method.The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2Al2SiO7:Eu3+ phosphors were investigated.X-ray diffraction(XRD) profiles showed that all peaks could be attributed to the tetragonal Ca2Al2SiO7 phase when the sample was annealed at 1000℃.Scanning electron microscopy(SEM) micrographs indicate that the phosphors have an irregularly rounded morphology with particles of about 200 nm.Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu3+-O2-and f-f transitions within the 4f6 configuration of Eu3+ ions,respectively.Emission spectra implied that the red luminescence could be attributed to the transitions from the 5D0 excited level to the 7FJ(J = 0,1,2,3,4) levels of Eu3+ ions with the main electric dipole transition 5D0→7F2(618 and 620 nm),and Eu3+ ions prefer to occupy a lower symmetry site in the crystal lattice.Moreover,the photoluminescence(PL) intensity was strongly dependent on both the sintering temperature and doping concentration,and the highest PL intensity was observed at an Eu3+ concentration x = 7 mol.% after annealing at 1100℃.The obtained Ca2Al2SiO7:Eu3+ phosphor may have potential application for the red lamp phosphor.
基金supported by the 973 Research Project of China (6134502)
文摘Nanocrystal SmBO3 powders were synthesized by nitrate-citrate sol-gel combustion method. The phase evolution, morphologies and absorbency of the synthesized powders were characterized by X-ray diffraction (XRD), Field emission scanning electronic microscope (FESEM), Fourier transform infrared spectroscopy (FTIR) and UV-3101PC spectrophotometer (UVPC), respectively. XRD and FESEM results showed that pure SmBO3 phase was obtained at 750 °C, with an average original particle size of about 100 nm. FTIR showed that there were apparently concentrated absorbent peaks between 500 and 1400 cm-1. Moreover, the reflectivity of the powders apparently decreased at the wavelength between 1.05 and 1.15 μm. Therefore, SmBO3 might be a kind of absorbent material for infrared laser.
基金Project(50872001) supported by the National Natural Science Foundation of ChinaProject(20060357003) supported by Research Fund for the Doctoral Program of Higher Education of ChinaProject(KJ2010A284) supported by the Natural Science Foundation of Anhui Higher Education Institution of China
文摘Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show the hexagonal wurtzite polycrystalline structure and that the sodium incorporation leads to the change in the structural characteristics of ZnO films.The SEM observations show that the surface morphology of the films is affected by the sodium incorporation.The transmission spectra show that the average transmittance of the films is above 85% in the visible range.The absorption edge initially blue-shifts and then red-shifts with the increase of Na doping content.The optical constants of these films were calculated using transmission spectra.Refractive indices of the films in the visible range decrease at first and then increase with increasing Na doping content.
文摘Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results of XRD show that the single crystalline phase is α-SrAl2O4. According to the observation of SEM, the particles of the samples are needle-like. Compared with the samples synthesized by solid state reaction, the grain size of the sol-gel method is to nanometer grade. A clear blue shift occurs in the excitation and emission spectra. The blue shift in nanocrystalline SrAl2O4∶Eu, Dy phosphor can be attributed to the quantum-size-effect of the luminescent particles.
基金Project supported by the Natural Science Basic Research Plan in Shaanxi Province of China (2004B13)
文摘The three-way catalysts (TWCs) promoters Ce0.6Zr0.4-xTbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x=0.05 to x=0.15 favors an increase of surface area from 66.8 to 80.4 m2·g-1 compared with the undoped sample Ce0.60Zr0.40O2 65.1 m2·g-1 after calcination at 650 ℃. Transmission electron microscopy (TEM) observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce4+ and Tb3+, and Zr existed in the form of Zr4+ on the surface of the samples. The doped samples were homogenous in composition; the introduction of Tb into the CeO2-ZrO2 promoters resulted in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.
文摘Highly ordered nanowire/tube arrays of Ni0.5Zn0.5Fe2O4 were fabricated by the sol-gel method in the pores of anodic alu- mina membrane (AAM). Whether nanowires or nanotubes were fabricated depends on immersion time. The immersion time was 15-40 s for nanotubes and over 60 s for nanowires. The topography and crystalline structure of the nanowire arrays were character- ized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). It was found that the length and diameter of the Ni0.5Zn0.5Fe2O4 nanowires are related to the thickness of the AAM and the diameter of the pores. The results indicated that the Ni0.5Zn0.5Fe2O4 nanowires are uniform and parallel to each other.
文摘Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466 nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8 h.
基金This work was financially supported by the Funds for Harbin Young Scholars (No.2005AFQXJ031).
文摘M-type Ba hexaferrites were successfully synthesized by sol-gel method. Several synthesizing factors, such as pH value, citric acid/metal ion ratio, and dispersion agent were mainly discussed. Fine and pure powders of BaFe12O19 were optimally synthesized under the conditions of the pH value is 7 and citric acid/metal ion ratio is 3. The X-ray diffraction analysis demonstrates that no impurity is observed in the synthesized powders after presintered at 450 ℃ and calcinated at 1100 ℃. SEM observations indicate that the size of the synthesized BaFe12O19 powders is small and uniform distribution. It can also be learned from SEM that the co-synthesizing sol-gel method can be in favor of the formation of finer particles.
文摘Two series of perovskite-type oxides with composition (La1-x)SrxFeO3（x≤0.8）and La1-xSrxFe1-yCoyO3（x=0.2; y=0.2, 0.4）powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method（N2 adsorption）and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.
文摘Nanometer Al2O3 is one of new types of functional materials with broad application and development prospects in the future. The basic principle and ways of nanometer Al2O3 fabricated using sol-gel technique were introduced, and the factors affecting nanometer Al2O3 fabricated using sol-gel method were analyzed. The progress in research on nanometer Al2O3 and the application fields of nanometer Al2O3 were reviewed. The existing problems and the problems prospect for nanometer Al2O3 were pointed out.
基金Projects(CC20120031,CC20110048)supported by Changzhou Science and Technology Innovation Project,China
文摘The CaCu3Ti4O12 xerogels,powders and ceramics were prepared through the sol-gel method using two kinds of organic acid(decanoic acid and decanedioic acid).The xerogels,powders and ceramics were characterized by the methods of TG-DTG,FT-IR,XRD,SEM and TEM.The dielectric properties of the ceramics were also measured.The results indicated that the powders calcined at 850°C for 2h are both nanometer scale particles.After sintering,the ceramics mainly consist of the CaCu3Ti4O12 phase.Compared with the powders prepared using monoacid,the particle size of the powders prepared using diacid obviously increases,and the grain size,the relative density and the whole permittivity of the ceramics increase as well.Specially,the ceramic prepared using decanedioic acid has higher relative density(97.3%),dielectric constant(316 808)and lower dielectric loss(0.242 5)at 30°C(10kHz)
基金This work was financially supported by the Natural Science Foundation of Tianjin (No. 33802311)
文摘The effect of different annealing temperatures on the structure, morphology, and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated. Zinc-oxide thin films were coated on quartz glass substrates by dip coating. Zinc nitrate, absolute ethanol, and citric acid were used as precursor, solvent, and chelating agent, respectively. The results show that ZnO films derived from zinc-citrate have lower crystallization temperature (below 400°C),and that the crystal structure is wurtzite. The films, treated over 500°C, consist of nano-particles and show to be porous at 600°C. The particle size of the film increases with the increase of the annealing temperature. The largest particle size is 60 nm at 600°C. The optical transmittances related to the annealing temperatures become 90% higher in the visible range. The film shows a starting absorption at 380 nm, and the optical band-gap of the thin film (fired at 500°C) is 3.25 eV and close to the intrinsic band-gap of ZnO (3.2 eV).
基金Project(GuiJiaoRen[2007]71)supported by the Research Funds of the Guangxi Key Laboratory of Environmental Engineering,Protection and Assessment Program to Sponsor Teams for Innovation in the Construction of Talent Highlands in Guangxi Institutions of Higher Learning,China
文摘The effect of Al-substitution on the electrochemical performances of Li3V2(PO4)3 cathode materials was studied.Samples with stoichiometric proportion of Li3AlxV2-x(PO4)3(x=0,0.05,0.10)were prepared by adding Al(NO3)3 in the raw materials of Li3V2(PO4)3.The XRD analysis shows that the Al-substituted Li3V2(PO4)3 has the same monoclinic structure as the un-substituted Li3V2(PO4)3.The SEM images show that Al-substituted Li3V2(PO4)3 has regular and uniform particles.The electrochemical measurements show that Al-substitution can improve the rate capability of cathode materials.The Li3Al0.05V1.95(PO4)3 sample shows the best high-rate performance.The discharge capacity at 1C rate is 119 mA·h/g with 30th capacity retention rate about 92.97%.The electrode reaction reversibility and electronic conductivity are enhanced,and the charge transfer resistance decreases through Al-substitution.The improved electrochemical performances of Al-substituted Li3V2(PO4)3 cathode materials offer some favorable properties for their commercial application.
