Gaofen-3-02(GF3-02)is the first C-band synthetic aperture radar(SAR)satellite with terrain observation with progressive scans of SAR(TOPSAR)imaging mode in China,which plays an essential role in marine environment mon...Gaofen-3-02(GF3-02)is the first C-band synthetic aperture radar(SAR)satellite with terrain observation with progressive scans of SAR(TOPSAR)imaging mode in China,which plays an essential role in marine environment monitoring.Given the weak scattering characteristics of the ocean,the system thermal noise superimposed on SAR images has significant interference,especially in cross-polarization channels.Noise-Equivalent Sigma-Zero(NESZ)is a measure of the sensitivity of the radar to areas of low backscatter.The NESZ is defined to be the scattering cross-section coefficient of an area which contributes a mean level in the image equal to the signal-independent additive noise level.For TOPSAR,NESZ exhibits the shape of the SAR scanning gain curve in the azimuth and the shape of the antenna pattern in the range.Therefore,the accurate measurement of NESZ plays a vital role in the application of spaceborne SAR sea surface cross-polarization data.This paper proposes a theoretical calculation method for the NESZ curve in GF3-02 TOPSAR mode based on SAR noise inner calibration data and the imaging algorithm.A method for correcting the error existing in the theoretical curve of NESZ is also proposed according to the relationship between sea surface backscattering and wind speed and the same characteristics of target scattering in the overlapping area of adjacent sub-swaths.According to assessment with wide-swath TOPSAR cross-polarization data,the GF3-02 TOPSAR mode has a very low thermal noise level,which is better than−33 dB at the edge of each beam,and controlled below−38 dB at the center of the beam.The two-dimensional reference curves of the NESZ of each beam are provided to the GF3-02 TOPSAR users.After discussing the relationship between normalized radar cross section(NRCS)and wind speed,we provide a formula for NRCS related to wind speed and radar incidence angle.Compared with the NRCS derived from this formula and the NESZ-subtracted NRCS of SAR images,the bias is−0.0048 dB,the Root Mean Square Error is 1.671 dB and the correlation coefficient is 0.939.展开更多
The 40-year-old Hangzhou MachineTools Works is a special manufacturerof surface grinders. It produces sevenseries with 120 specifications of varioussurface grinders. In addition to meetingdomestic demand, its products...The 40-year-old Hangzhou MachineTools Works is a special manufacturerof surface grinders. It produces sevenseries with 120 specifications of varioussurface grinders. In addition to meetingdomestic demand, its products have beenexported to some 60 countries and regions,including the USA, the UK, Germany andJapan. The M7150HX10 is one of its exportproducts.展开更多
BACKGROUND Nucleos(t)ide analog(NA)has shown limited effectiveness against hepatitis B surface antigen(HBsAg)clearance in chronic hepatitis B(CHB)patients.AIM To evaluate the efficacy and safety of add-on peginterfero...BACKGROUND Nucleos(t)ide analog(NA)has shown limited effectiveness against hepatitis B surface antigen(HBsAg)clearance in chronic hepatitis B(CHB)patients.AIM To evaluate the efficacy and safety of add-on peginterferonα-2a(peg-IFNα-2a)to an ongoing NA regimen in CHB patients.METHODS In this observational study,195 CHB patients with HBsAg≤1500 IU/m L,hepatitis B e antigen(HBeAg)-negative(including HBeAg-negative patients or HBeAg-positive patients who achieved HBeAg-negative after antiviral treatment with NA)and hepatitis B virus-deoxyribonucleic acid<1.0×10^2 IU/mL after over 1 year of NA therapy were enrolled between November 2015 and December2018 at the Second Affiliated Hospital of Xi'an Jiaotong University,China.Patients were given the choice between receiving either peg-IFNα-2a add-on therapy to an ongoing NA regimen(add-on group,n=91)or continuous NA monotherapy(monotherapy group,n=104)after being informed of the benefits and risks of the peg-IFNα-2a therapy.Total therapy duration of peg-IFNα-2a was 48 wk.All patients were followed-up to week 72(24 wk after discontinuation of peg-IFNα-2a).The primary endpoint was the proportion of patients with HBsAg clearance at week 72.RESULTS Demographic and baseline characteristics were comparable between the two groups.Intention-to-treatment analysis showed that the HBsAg clearance rate in the add-on group and monotherapy group was 37.4%(34/91)and 1.9%(2/104)at week 72,respectively.The HBsAg seroconversion rate in the add-on group was 29.7%(27/91)at week 72,and no patient in the monotherapy group achieved HBsAg seroconversion at week 72.The HBsAg clearance and seroconversion rates in the add-on group were significantly higher than in the monotherapy group at week 72(P<0.001).Younger patients,lower baseline HBsAg concentration,lower HBsAg concentrations at weeks 12 and 24,greater HBsAg decline from baseline to weeks 12 and 24 and the alanine aminotransferase≥2×upper limit of normal during the first 12 wk of therapy were strong predictors of HBsAg clearance in patients with peg-IFNα-2a add-on treatment.Regarding the safety of the treatment,4.4%(4/91)of patients in the add-on group discontinued peg-IFNα-2a due to adverse events.No severe adverse events were noted.CONCLUSION Peg-IFNα-2a as an add-on therapy augments HBsAg clearance in HBeAg-negative CHB patients with HBsAg≤1500 IU/m L after over 1 year of NA therapy.展开更多
The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an incr...The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.展开更多
In order to determine the structures of Si（111）-√7 √3-In surfaces and to understand their electronic properties, we construct six models of both hexagonal and rectangular types and perform first-principles calcula...In order to determine the structures of Si（111）-√7 √3-In surfaces and to understand their electronic properties, we construct six models of both hexagonal and rectangular types and perform first-principles calculations. Their scanning tunneling microscopic images and work functions are simulated and compared with experimental results. In this way, the hex-H3＇ and rect-T1 models are identified as the experimental configurations for the hexagonal and rectangular types, respectively. The structural evolution mechanism of the In/Si（lll） surface with indium coverage around 1.0 monolayer is discussed. The 4×1 and -√7× √3 phases are suggested to have two different types of evolution mechanisms, consistent with experimental results.展开更多
This study investigates the structure and propagation of intraseasonal sea surface temperature（SST） variability in the South China Sea（SCS） on the 30-60-day timescale during boreal summer（May-September）. TRMM-ba...This study investigates the structure and propagation of intraseasonal sea surface temperature（SST） variability in the South China Sea（SCS） on the 30-60-day timescale during boreal summer（May-September）. TRMM-based SST, GODAS oceanic reanalysis and ERA-Interim atmospheric reanalysis datasets from 1998 to 2013 are used to examine quantitatively the atmospheric thermodynamic and oceanic dynamic mechanisms responsible for its formation. Power spectra show that the 30-60-day SST variability is predominant, accounting for 60% of the variance of the 10-90-day variability over most of the SCS. Composite analyses demonstrate that the 30-60-day SST variability is characterized by the alternate occurrence of basin-wide positive and negative SST anomalies in the SCS, with positive（negative） SST anomalies accompanied by anomalous northeasterlies（southwesterlies）. The transition and expansion of SST anomalies are driven by the monsoonal trough-ridge seesaw pattern that migrates northward from the equator to the northern SCS. Quantitative diagnosis of the composite mixed-layer heat budgets shows that, within a strong 30-60-day cycle, the atmospheric thermal forcing is indeed a dominant factor, with the mixed-layer net heat flux（MNHF） contributing around 60% of the total SST tendency, while vertical entrainment contributes more than 30%. However, the entrainment-induced SST tendency is sometimes as large as the MNHF-induced component, implying that ocean processes are sometimes as important as surface fluxes in generating the30-60-day SST variability in the SCS.展开更多
Effects of Zr/Ti molar ratio in SO42-/ZrO2-TiO2 solid acid catalyst calcined at different temperatures on its surface properties and catalytic activity were thoroughly investigated in this paper. The physicochemical c...Effects of Zr/Ti molar ratio in SO42-/ZrO2-TiO2 solid acid catalyst calcined at different temperatures on its surface properties and catalytic activity were thoroughly investigated in this paper. The physicochemical characteristics of prepared samples were determined by N2 adsorptiondesorption, XRD, NH3-TPD and XPS techniques, respectively. It was found that the crystallization temperature of the samples increased after the combination of ZrO2 and TiO2; and phase transformations from the anatase to the rutile of TiO2 species and the tetragonal to the monoclinic of ZrO2 species were effectively suppressed at higher temperature. The sample with a Zr/Ti molar ratio of 3/1 calcined at 450℃ showed the highest surface area and the most acid sites among all the tested samples. The acid site densities of samples were relatively closed to each other if they were calcined at the same temperature, however, decreased with the calcination temperature. The result indicates that the sulfur content in samples is a crucial factor to control the acid site density. Calcining the sample at 650℃ and higher temperatures resulted in a significant desorption of sulfate ion on the samples. The synthesized samples were evaluated as a potential catalyst for glucose conversion under the near-critical methanol conditions （200℃/4 MPa）. The results suggested that the relatively weaker acid sites of the catalyst were more favorable for the accumulation of methyl glucosides, while the moderate acid sites were responsible for the formation of methyl levulinate. The catalytic activity for methyl levulinate production almost increases linearly with the catalyst acid site density. The catalyst deactivation is due to the loss of sulfate ion and the two catalysts with Zr/Ti molar ratios of 3/1 and 1/3 could effectively alleviate the deactivation caused by sulfate solution in the reaction medium and can be reused after calcination with the reuse rate of over 90% in terms of the methyl levulinate selectivity.展开更多
The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is...The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is assumed. Dis- persion equations relating phase velocity to material con- stants for the existence of various modes are obtained in a simple mathematical form for a piezoelectric material of class 6mm. It is discovered and proved by numerical examples in this paper that a novel Bleustein-Gulyaev （B-G） type of transverse surface wave can exist in such piezoelectric cou- pled solid media when the bulk-shear-wave velocity in the substrate is less than that in the piezoelectric layer but greater than the corresponding B-G wave velocity in the same pie- zoelectric material with an electroded surface. Such a wave does not exist in such layered structures in the absence of pie- zoelectricity. The mode shapes for displacement and electric potential in the piezoelectric layer are obtained and discussed theoretically. The study extends the regime of transverse sur- face waves and may lead to potential applications to surface acoustic wave devices.展开更多
A new 3D velocity model of the crust and upper mantle in the southeastern （SE） margin of the Tibetan plateau was obtained by joint inversion of body- and sur- face-wave data. For the body-wave data, we used 7190 eve...A new 3D velocity model of the crust and upper mantle in the southeastern （SE） margin of the Tibetan plateau was obtained by joint inversion of body- and sur- face-wave data. For the body-wave data, we used 7190 events recorded by 102 stations in the SE margin of the Tibetan plateau. The surface-wave data consist of Rayleigh wave phase velocity dispersion curves obtained from ambient noise cross-correlation analysis recorded by a dense array in the SE margin of the Tibetan plateau. The joint inversion clearly improves the Vs model because it is constrained by both data types. The results show that at around 10 km depth there are two low-velocity anomalies embedded within three high-velocity bodies along the Longmenshan fault system. These high-velocity bodies correspond well with the Precambrian massifs, and the two located to the northeast of 2013 Ms 7.0 Lushan earthquake are associated with high fault slip areas during the 2008 Wenchuan earthquake. The aftershock gap between 2013 Lushan earthquake and 2008 Wenchuan earthquake is associated with low-velocity anomalies, which also acts as a barrier zone for ruptures of two earthquakes. Generally large earthquakes （M 〉 5） in the region occurring from 2008 to 2015 are located around the high-velocity zones, indicating that they may act as asperities for these large earthquakes. Joint inversion results also clearly show that there exist low-velocity or weak zones in the mid-lower crust, which are not evenly distributed beneath the SE margin of Tibetan plateau.展开更多
The behavior of Taylor-Couette （TC） flow has been extensively studied. However, no suitable torque prediction models exist for high-capacity fluid machinery. The Eckhardt-Grossmann-Lohse （EGL） theory, derived base...The behavior of Taylor-Couette （TC） flow has been extensively studied. However, no suitable torque prediction models exist for high-capacity fluid machinery. The Eckhardt-Grossmann-Lohse （EGL） theory, derived based on the Navier-Stokes equations, is proposed to model torque behavior. This are the significant energy theory suggests that surfaces transfer interfaces between cylinders and annular flow. This study mainly focuses on the effects of surface texture on momentum transfer behavior through global torque measurement. First, a power-law torque behavior model is built to reveal the relationship between dimensionless torque and the Taylor number based on the EGL theory. Second, TC flow appa- ratus is designed and built based on the CNC machine tool to verify the torque behavior model. Third, four surface texture films are tested to check the effects of surface texture on momentum transfer. A stereo microscope and three-dimensional topography instrument are employed to analyze surface morphology. Global torque behavior is measured by rotating a multi component dynamometer, and the effects of surface texture on the annular flow behavior are observed via images obtained using a high-speed camera. Finally, torque behaviors under four differentsurface conditions are fitted and compared. The experi- mental results indicate that surface textures have a remarkable influence on torque behavior, and that the peak roughness of surface texture enhances the momentum transfer by strengthening the fluctuation in the TC flow.展开更多
The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on ...The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on TiOz anatase（101） surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe（CN）6]^4- adsorption on the （101） surface could lead to a large red shift of the anatase optical absorption threshold, which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development ofphotovoltaic materials that are active under visible light.展开更多
In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardwar...In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.展开更多
Surface modification of poly [1-(trimethylsilyl)-1-propyne] (PTMSP) membranes bybromine vapor has been studied. It is shown that Br/C atomic ratio at the surfaces increased withthe time of bromination until about 60 m...Surface modification of poly [1-(trimethylsilyl)-1-propyne] (PTMSP) membranes bybromine vapor has been studied. It is shown that Br/C atomic ratio at the surfaces increased withthe time of bromination until about 60 min, then it reached a plateau. The results of XPS and IRstudies indicated that the addition of bromine to double bonds and the replacement of H on CH_3 bybromine had taken place so that a new peak at 286.0 eV (C--Br)in C_(1s) spectra and some newbands, e. g. at 1220 and 580cm^(-1) in IR spectra were formed. The fact,t Po_2, permeability ofoxygen, decreased and α_(O_2/N_2), separation factor of oxygen relative to nitrogen, increased withbromination time, shows that surface modification of PTMSP by bromine may be an efficient approach to prepare PTMSP membranes used for practical gas separations.展开更多
We report the formation and local electronic structure of Ge clusters on the Si（111）-7×7 surface studied by using variable temperature scanning tunnelling microscopy （VT-STM） and low-temperature scanning tunn...We report the formation and local electronic structure of Ge clusters on the Si（111）-7×7 surface studied by using variable temperature scanning tunnelling microscopy （VT-STM） and low-temperature scanning tunnelling spectroscopy （STS）. Atom-resolved STM images reveal that the Ce atoms are prone to forming clusters with 1.0 nm in diameter for coverage up to 0.12 ML. Such Ce clusters preferentially nucleate at the centre of the faulted-half unit cells, leading to the ＇dark sites＇ of Si centre adatoms from the surrounding three unfaulted-half unit cells in filled-state images. Biasdependent STM images show the charge transfer from the neighbouring Si adatoms to Ce clusters. Low-temperature STS of the Ce clusters reveals that there is a band gap on the Ce cluster and the large voltage threshold is about 0.9 V.展开更多
Ruthenium loaded on activated carbon pre-treated by HNO3 was used to catalyze the reaction of 1-(2-Aminoethyl)-2-imidazolidone (AEI) synthesized from ethylenediamine, ethanolamine and CO2. Response surface methodology...Ruthenium loaded on activated carbon pre-treated by HNO3 was used to catalyze the reaction of 1-(2-Aminoethyl)-2-imidazolidone (AEI) synthesized from ethylenediamine, ethanolamine and CO2. Response surface methodology (RSM) based on Box-Behnken design (BBD) was employed to optimize the synthesis of AEI. The statistical analysis results showed that the yield of AEI was significantly affected by the CO2 pressure, reaction temperature and reaction time. According to the results of variance analysis, the value of the determination coefficient of 0.9854 was in reasonable agreement with the “Adj R-Squared” of 0.9666, which means this model can predict the yield of AEI well and can be used to optimize reaction conditions for higher AEI yield. The optimal values of AEI yield predicted by RSM was 84.9% under temperature 206.51?C, CO2 pressure 9.35 Mpa, reaction time 10.11 h, and the verification experiment yield of AEI was 83.1%.展开更多
In this work we study the adsorptions of some small molecules or group on the hydrogenated C（100）-2×1 surface using density functional theory method. The calculated results show that the ionization potential ...In this work we study the adsorptions of some small molecules or group on the hydrogenated C（100）-2×1 surface using density functional theory method. The calculated results show that the ionization potential （IP） of the hydrogenated C（100）-2×1 surfaces after adsorption has amphoteric characteristics. From the weak basic NH3 molecule with small IP and negative electron affinity （EA）, through the neutral H2O molecule, to the weak acid HF molecule and the OH group with large EA and IP, the IP values of the adsorbed diamond surfaces vary from decrease, through invariability, to slight increase for HF and obvious increase for OH. In all adsorption species, only the OH group makes the hydrogenated C（100）-2×1 surface change to the metal from the semiconductor with a wide-band gap, while the others only introduce impurity states into the electronic structures of the hydrogenated C（100）-2×1 surfaces.展开更多
Sea surface electric field observations off the coast from Goa (15°25'N, 73°47'E) to Madras (13°04'N, 80°15'E) around Sri Lanka, in a distance range 25-135 km from coast, during 9-2...Sea surface electric field observations off the coast from Goa (15°25'N, 73°47'E) to Madras (13°04'N, 80°15'E) around Sri Lanka, in a distance range 25-135 km from coast, during 9-20 May 1983 were taken. In this paper we have examined the diurnal variation of electric field in the Arabian Sea, Indian Ocean and Bay of Bengal regions covered during the cruise of the research ship ORV Gaveshani. An aspect of electric field dependence on coastal distance and Aitken Nuclei concentration has also been studied. An attempt to examine the latitude dependence of field was also made. Results obtained in the above studies are presented and compared with those obtained elsewhere.展开更多
Single point diamond fly cutting is widely used in the manufacture of large-aperture ultra-precision optical elements. However,some micro waviness( amplitude about 30 nm,wavelength about 15 mm) along the cutting direc...Single point diamond fly cutting is widely used in the manufacture of large-aperture ultra-precision optical elements. However,some micro waviness( amplitude about 30 nm,wavelength about 15 mm) along the cutting direction which will decrease the quality of the optical elements can always be found in the processed surface,and the axial vibration of the spindle caused by the cut-in process is speculated as the immediate cause of this waviness. In this paper,the analytical method of dynamic mesh is applied for simulating the dynamic behavior of the vertical spindle. The consequence is then exerted to the fly cutter and the processed surface profile is simulated. The wavelength of the simulation result coincides well with the experimental result which proves the importance of the cut-in process during the single point diamond fly cutting.展开更多
基金The National Natural Science Foundation of China under contract No.41976169.
文摘Gaofen-3-02(GF3-02)is the first C-band synthetic aperture radar(SAR)satellite with terrain observation with progressive scans of SAR(TOPSAR)imaging mode in China,which plays an essential role in marine environment monitoring.Given the weak scattering characteristics of the ocean,the system thermal noise superimposed on SAR images has significant interference,especially in cross-polarization channels.Noise-Equivalent Sigma-Zero(NESZ)is a measure of the sensitivity of the radar to areas of low backscatter.The NESZ is defined to be the scattering cross-section coefficient of an area which contributes a mean level in the image equal to the signal-independent additive noise level.For TOPSAR,NESZ exhibits the shape of the SAR scanning gain curve in the azimuth and the shape of the antenna pattern in the range.Therefore,the accurate measurement of NESZ plays a vital role in the application of spaceborne SAR sea surface cross-polarization data.This paper proposes a theoretical calculation method for the NESZ curve in GF3-02 TOPSAR mode based on SAR noise inner calibration data and the imaging algorithm.A method for correcting the error existing in the theoretical curve of NESZ is also proposed according to the relationship between sea surface backscattering and wind speed and the same characteristics of target scattering in the overlapping area of adjacent sub-swaths.According to assessment with wide-swath TOPSAR cross-polarization data,the GF3-02 TOPSAR mode has a very low thermal noise level,which is better than−33 dB at the edge of each beam,and controlled below−38 dB at the center of the beam.The two-dimensional reference curves of the NESZ of each beam are provided to the GF3-02 TOPSAR users.After discussing the relationship between normalized radar cross section(NRCS)and wind speed,we provide a formula for NRCS related to wind speed and radar incidence angle.Compared with the NRCS derived from this formula and the NESZ-subtracted NRCS of SAR images,the bias is−0.0048 dB,the Root Mean Square Error is 1.671 dB and the correlation coefficient is 0.939.
文摘The 40-year-old Hangzhou MachineTools Works is a special manufacturerof surface grinders. It produces sevenseries with 120 specifications of varioussurface grinders. In addition to meetingdomestic demand, its products have beenexported to some 60 countries and regions,including the USA, the UK, Germany andJapan. The M7150HX10 is one of its exportproducts.
基金the National Natural Science Foundation of China,No.31500650。
文摘BACKGROUND Nucleos(t)ide analog(NA)has shown limited effectiveness against hepatitis B surface antigen(HBsAg)clearance in chronic hepatitis B(CHB)patients.AIM To evaluate the efficacy and safety of add-on peginterferonα-2a(peg-IFNα-2a)to an ongoing NA regimen in CHB patients.METHODS In this observational study,195 CHB patients with HBsAg≤1500 IU/m L,hepatitis B e antigen(HBeAg)-negative(including HBeAg-negative patients or HBeAg-positive patients who achieved HBeAg-negative after antiviral treatment with NA)and hepatitis B virus-deoxyribonucleic acid<1.0×10^2 IU/mL after over 1 year of NA therapy were enrolled between November 2015 and December2018 at the Second Affiliated Hospital of Xi'an Jiaotong University,China.Patients were given the choice between receiving either peg-IFNα-2a add-on therapy to an ongoing NA regimen(add-on group,n=91)or continuous NA monotherapy(monotherapy group,n=104)after being informed of the benefits and risks of the peg-IFNα-2a therapy.Total therapy duration of peg-IFNα-2a was 48 wk.All patients were followed-up to week 72(24 wk after discontinuation of peg-IFNα-2a).The primary endpoint was the proportion of patients with HBsAg clearance at week 72.RESULTS Demographic and baseline characteristics were comparable between the two groups.Intention-to-treatment analysis showed that the HBsAg clearance rate in the add-on group and monotherapy group was 37.4%(34/91)and 1.9%(2/104)at week 72,respectively.The HBsAg seroconversion rate in the add-on group was 29.7%(27/91)at week 72,and no patient in the monotherapy group achieved HBsAg seroconversion at week 72.The HBsAg clearance and seroconversion rates in the add-on group were significantly higher than in the monotherapy group at week 72(P<0.001).Younger patients,lower baseline HBsAg concentration,lower HBsAg concentrations at weeks 12 and 24,greater HBsAg decline from baseline to weeks 12 and 24 and the alanine aminotransferase≥2×upper limit of normal during the first 12 wk of therapy were strong predictors of HBsAg clearance in patients with peg-IFNα-2a add-on treatment.Regarding the safety of the treatment,4.4%(4/91)of patients in the add-on group discontinued peg-IFNα-2a due to adverse events.No severe adverse events were noted.CONCLUSION Peg-IFNα-2a as an add-on therapy augments HBsAg clearance in HBeAg-negative CHB patients with HBsAg≤1500 IU/m L after over 1 year of NA therapy.
基金Project supported by the Natural Science Basic Research Plan in Shaanxi Province of China (2004B13)
文摘The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.
基金V. ACKNOWLEDGMENTS This work was supported by the National Natural Science Foundation of China （No.20603032, No.20733004, No.21121003, No.91021004, No.20933006）, the National Key Basic Research Program （No.2011CB921400）, the Foundation of National Excellent Doctoral Dissertation of China （No.200736）, the Fundamental Research Funds for the Central Universities （No.WK2340000006 and No.WK2060140005）, and the Shanghai Supercompurer Center, the USTC-HP HPC Project, and the SCCAS.
文摘In order to determine the structures of Si（111）-√7 √3-In surfaces and to understand their electronic properties, we construct six models of both hexagonal and rectangular types and perform first-principles calculations. Their scanning tunneling microscopic images and work functions are simulated and compared with experimental results. In this way, the hex-H3＇ and rect-T1 models are identified as the experimental configurations for the hexagonal and rectangular types, respectively. The structural evolution mechanism of the In/Si（lll） surface with indium coverage around 1.0 monolayer is discussed. The 4×1 and -√7× √3 phases are suggested to have two different types of evolution mechanisms, consistent with experimental results.
基金supported by the SOA Program on Global Change and Air–Sea Interactions (Grant No.GASI-IPOVAI03)the National Basic Research Program of China (Grant No.2014CB953902)+1 种基金the Natural Science Foundation of China (Grant Nos.91537103 and 41375087)the Priority Research Program of the Chinese Academy of Sciences (Grant Nos.QYZDY-SSWDQC018 and XDA11010402)
文摘This study investigates the structure and propagation of intraseasonal sea surface temperature（SST） variability in the South China Sea（SCS） on the 30-60-day timescale during boreal summer（May-September）. TRMM-based SST, GODAS oceanic reanalysis and ERA-Interim atmospheric reanalysis datasets from 1998 to 2013 are used to examine quantitatively the atmospheric thermodynamic and oceanic dynamic mechanisms responsible for its formation. Power spectra show that the 30-60-day SST variability is predominant, accounting for 60% of the variance of the 10-90-day variability over most of the SCS. Composite analyses demonstrate that the 30-60-day SST variability is characterized by the alternate occurrence of basin-wide positive and negative SST anomalies in the SCS, with positive（negative） SST anomalies accompanied by anomalous northeasterlies（southwesterlies）. The transition and expansion of SST anomalies are driven by the monsoonal trough-ridge seesaw pattern that migrates northward from the equator to the northern SCS. Quantitative diagnosis of the composite mixed-layer heat budgets shows that, within a strong 30-60-day cycle, the atmospheric thermal forcing is indeed a dominant factor, with the mixed-layer net heat flux（MNHF） contributing around 60% of the total SST tendency, while vertical entrainment contributes more than 30%. However, the entrainment-induced SST tendency is sometimes as large as the MNHF-induced component, implying that ocean processes are sometimes as important as surface fluxes in generating the30-60-day SST variability in the SCS.
基金supported by the National Key Basic Research Program (2010CB732201) from the Ministry of Science and Technology of Chinathe Natural Science Foundation of China (U0733001, 50776035)the Basic Research Foundation from the Ministry of Education for Universities (2010121077)
文摘Effects of Zr/Ti molar ratio in SO42-/ZrO2-TiO2 solid acid catalyst calcined at different temperatures on its surface properties and catalytic activity were thoroughly investigated in this paper. The physicochemical characteristics of prepared samples were determined by N2 adsorptiondesorption, XRD, NH3-TPD and XPS techniques, respectively. It was found that the crystallization temperature of the samples increased after the combination of ZrO2 and TiO2; and phase transformations from the anatase to the rutile of TiO2 species and the tetragonal to the monoclinic of ZrO2 species were effectively suppressed at higher temperature. The sample with a Zr/Ti molar ratio of 3/1 calcined at 450℃ showed the highest surface area and the most acid sites among all the tested samples. The acid site densities of samples were relatively closed to each other if they were calcined at the same temperature, however, decreased with the calcination temperature. The result indicates that the sulfur content in samples is a crucial factor to control the acid site density. Calcining the sample at 650℃ and higher temperatures resulted in a significant desorption of sulfate ion on the samples. The synthesized samples were evaluated as a potential catalyst for glucose conversion under the near-critical methanol conditions （200℃/4 MPa）. The results suggested that the relatively weaker acid sites of the catalyst were more favorable for the accumulation of methyl glucosides, while the moderate acid sites were responsible for the formation of methyl levulinate. The catalytic activity for methyl levulinate production almost increases linearly with the catalyst acid site density. The catalyst deactivation is due to the loss of sulfate ion and the two catalysts with Zr/Ti molar ratios of 3/1 and 1/3 could effectively alleviate the deactivation caused by sulfate solution in the reaction medium and can be reused after calcination with the reuse rate of over 90% in terms of the methyl levulinate selectivity.
基金supported by the National Natural Science Foundation of China(10972171)the Program for New Century Excellent Talents in Universities(NCET-08-0429)
文摘The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is assumed. Dis- persion equations relating phase velocity to material con- stants for the existence of various modes are obtained in a simple mathematical form for a piezoelectric material of class 6mm. It is discovered and proved by numerical examples in this paper that a novel Bleustein-Gulyaev （B-G） type of transverse surface wave can exist in such piezoelectric cou- pled solid media when the bulk-shear-wave velocity in the substrate is less than that in the piezoelectric layer but greater than the corresponding B-G wave velocity in the same pie- zoelectric material with an electroded surface. Such a wave does not exist in such layered structures in the absence of pie- zoelectricity. The mode shapes for displacement and electric potential in the piezoelectric layer are obtained and discussed theoretically. The study extends the regime of transverse sur- face waves and may lead to potential applications to surface acoustic wave devices.
基金supported by the Natural National Science Foundation of China under grant number 41474039China National Special Fund for Earthquake Scientific Research in Public Interest under grant number 2016 CESE 0201+1 种基金Shanghai Committee of Science and Technology under grant number 14231202600the Fundamental Research Funds for the Central Universities under grant number WK2080000053
文摘A new 3D velocity model of the crust and upper mantle in the southeastern （SE） margin of the Tibetan plateau was obtained by joint inversion of body- and sur- face-wave data. For the body-wave data, we used 7190 events recorded by 102 stations in the SE margin of the Tibetan plateau. The surface-wave data consist of Rayleigh wave phase velocity dispersion curves obtained from ambient noise cross-correlation analysis recorded by a dense array in the SE margin of the Tibetan plateau. The joint inversion clearly improves the Vs model because it is constrained by both data types. The results show that at around 10 km depth there are two low-velocity anomalies embedded within three high-velocity bodies along the Longmenshan fault system. These high-velocity bodies correspond well with the Precambrian massifs, and the two located to the northeast of 2013 Ms 7.0 Lushan earthquake are associated with high fault slip areas during the 2008 Wenchuan earthquake. The aftershock gap between 2013 Lushan earthquake and 2008 Wenchuan earthquake is associated with low-velocity anomalies, which also acts as a barrier zone for ruptures of two earthquakes. Generally large earthquakes （M 〉 5） in the region occurring from 2008 to 2015 are located around the high-velocity zones, indicating that they may act as asperities for these large earthquakes. Joint inversion results also clearly show that there exist low-velocity or weak zones in the mid-lower crust, which are not evenly distributed beneath the SE margin of Tibetan plateau.
基金Supported by National Programs for Fundamental Research and Development of China(Grant Nos.2009CB724308,2015CB057302)National Science and Technology Major Project of China(Grant No.2013ZX06002002-017)
文摘The behavior of Taylor-Couette （TC） flow has been extensively studied. However, no suitable torque prediction models exist for high-capacity fluid machinery. The Eckhardt-Grossmann-Lohse （EGL） theory, derived based on the Navier-Stokes equations, is proposed to model torque behavior. This are the significant energy theory suggests that surfaces transfer interfaces between cylinders and annular flow. This study mainly focuses on the effects of surface texture on momentum transfer behavior through global torque measurement. First, a power-law torque behavior model is built to reveal the relationship between dimensionless torque and the Taylor number based on the EGL theory. Second, TC flow appa- ratus is designed and built based on the CNC machine tool to verify the torque behavior model. Third, four surface texture films are tested to check the effects of surface texture on momentum transfer. A stereo microscope and three-dimensional topography instrument are employed to analyze surface morphology. Global torque behavior is measured by rotating a multi component dynamometer, and the effects of surface texture on the annular flow behavior are observed via images obtained using a high-speed camera. Finally, torque behaviors under four differentsurface conditions are fitted and compared. The experi- mental results indicate that surface textures have a remarkable influence on torque behavior, and that the peak roughness of surface texture enhances the momentum transfer by strengthening the fluctuation in the TC flow.
基金the Scientific and Technology Foundation of Fuzhou University and the Key Project of Fujian Province (2005HZ01-2-6)
文摘The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on TiOz anatase（101） surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe（CN）6]^4- adsorption on the （101） surface could lead to a large red shift of the anatase optical absorption threshold, which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development ofphotovoltaic materials that are active under visible light.
文摘In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.
基金The project is supported by the National Natural Science Foundation of China
文摘Surface modification of poly [1-(trimethylsilyl)-1-propyne] (PTMSP) membranes bybromine vapor has been studied. It is shown that Br/C atomic ratio at the surfaces increased withthe time of bromination until about 60 min, then it reached a plateau. The results of XPS and IRstudies indicated that the addition of bromine to double bonds and the replacement of H on CH_3 bybromine had taken place so that a new peak at 286.0 eV (C--Br)in C_(1s) spectra and some newbands, e. g. at 1220 and 580cm^(-1) in IR spectra were formed. The fact,t Po_2, permeability ofoxygen, decreased and α_(O_2/N_2), separation factor of oxygen relative to nitrogen, increased withbromination time, shows that surface modification of PTMSP by bromine may be an efficient approach to prepare PTMSP membranes used for practical gas separations.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 90406022 and 10674159）.
文摘We report the formation and local electronic structure of Ge clusters on the Si（111）-7×7 surface studied by using variable temperature scanning tunnelling microscopy （VT-STM） and low-temperature scanning tunnelling spectroscopy （STS）. Atom-resolved STM images reveal that the Ce atoms are prone to forming clusters with 1.0 nm in diameter for coverage up to 0.12 ML. Such Ce clusters preferentially nucleate at the centre of the faulted-half unit cells, leading to the ＇dark sites＇ of Si centre adatoms from the surrounding three unfaulted-half unit cells in filled-state images. Biasdependent STM images show the charge transfer from the neighbouring Si adatoms to Ce clusters. Low-temperature STS of the Ce clusters reveals that there is a band gap on the Ce cluster and the large voltage threshold is about 0.9 V.
文摘Ruthenium loaded on activated carbon pre-treated by HNO3 was used to catalyze the reaction of 1-(2-Aminoethyl)-2-imidazolidone (AEI) synthesized from ethylenediamine, ethanolamine and CO2. Response surface methodology (RSM) based on Box-Behnken design (BBD) was employed to optimize the synthesis of AEI. The statistical analysis results showed that the yield of AEI was significantly affected by the CO2 pressure, reaction temperature and reaction time. According to the results of variance analysis, the value of the determination coefficient of 0.9854 was in reasonable agreement with the “Adj R-Squared” of 0.9666, which means this model can predict the yield of AEI well and can be used to optimize reaction conditions for higher AEI yield. The optimal values of AEI yield predicted by RSM was 84.9% under temperature 206.51?C, CO2 pressure 9.35 Mpa, reaction time 10.11 h, and the verification experiment yield of AEI was 83.1%.
基金Supported by the Natural Science Foundation of Inner Mongolia (2010BS0805)Inner Mongolia University of Science & Technology Foundation (2009NC008)
文摘In this work we study the adsorptions of some small molecules or group on the hydrogenated C（100）-2×1 surface using density functional theory method. The calculated results show that the ionization potential （IP） of the hydrogenated C（100）-2×1 surfaces after adsorption has amphoteric characteristics. From the weak basic NH3 molecule with small IP and negative electron affinity （EA）, through the neutral H2O molecule, to the weak acid HF molecule and the OH group with large EA and IP, the IP values of the adsorbed diamond surfaces vary from decrease, through invariability, to slight increase for HF and obvious increase for OH. In all adsorption species, only the OH group makes the hydrogenated C（100）-2×1 surface change to the metal from the semiconductor with a wide-band gap, while the others only introduce impurity states into the electronic structures of the hydrogenated C（100）-2×1 surfaces.
文摘Sea surface electric field observations off the coast from Goa (15°25'N, 73°47'E) to Madras (13°04'N, 80°15'E) around Sri Lanka, in a distance range 25-135 km from coast, during 9-20 May 1983 were taken. In this paper we have examined the diurnal variation of electric field in the Arabian Sea, Indian Ocean and Bay of Bengal regions covered during the cruise of the research ship ORV Gaveshani. An aspect of electric field dependence on coastal distance and Aitken Nuclei concentration has also been studied. An attempt to examine the latitude dependence of field was also made. Results obtained in the above studies are presented and compared with those obtained elsewhere.
基金Sponsored by the National Science and Technology Special Program(Grant No.2011ZX04004-041)the National Natural Science Foundation of China(Grant No.90923023 and No.51275115)
文摘Single point diamond fly cutting is widely used in the manufacture of large-aperture ultra-precision optical elements. However,some micro waviness( amplitude about 30 nm,wavelength about 15 mm) along the cutting direction which will decrease the quality of the optical elements can always be found in the processed surface,and the axial vibration of the spindle caused by the cut-in process is speculated as the immediate cause of this waviness. In this paper,the analytical method of dynamic mesh is applied for simulating the dynamic behavior of the vertical spindle. The consequence is then exerted to the fly cutter and the processed surface profile is simulated. The wavelength of the simulation result coincides well with the experimental result which proves the importance of the cut-in process during the single point diamond fly cutting.
