Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most o...Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most of which are based on the global rock bolt response evaluated in pull-out tests.This paper presents a laboratory experimental setup aiming to capture the rock formation effect,while using distributed fiber optic sensing to quantify the effect of the confinement and the reinforcement pull-out behavior on a more local level.It is shown that the behavior along the sample itself varies,with certain points exhibiting stress drops with crack formation.Some edge effects related to the kinematic freedom of the grout to dilate are also observed.Regardless,it was found that the mid-level response is quite similar to the average response along the sample.The ability to characterize the variation of the response along the sample is one of the many advantages high-resolution fiber optic sensing allows in such investigations.The paper also offers a plasticity-based hardening load transfer function,representing a"slice"of the anchor.The paper describes in detail the development of the model and the calibration/determination of its parameters.The suggested model captures well the coupled behavior in which the pull-out process leads to an increase in the confining stress due to dilative behavior.展开更多
Resonance effects in parallel jointed rocks subject to stress waves are investigated using transfer functions,derived from signals generated through numerical modelling.Resonance is important for a range of engineerin...Resonance effects in parallel jointed rocks subject to stress waves are investigated using transfer functions,derived from signals generated through numerical modelling.Resonance is important for a range of engineering situations as it identifies the frequency of waves which will be favourably transmitted.Two different numerical methods are used for this study,adopting the finite difference method and the combined discrete element-finite difference method.The numerical models are validated by replicating results from previous studies.The two methods are found to behave similarly and show the same resonance effects;one operating at low frequency and the other operating at relatively high frequency.These resonance effects are interpreted in terms of simple physical systems and analytical equations are derived to predict the resonant frequencies of complex rock masses.Low frequency resonance is shown to be generated by a system synonymous with masses between springs,described as spring resonance,with an equal number of resonant frequencies as the number of blocks.High frequency resonance is generated through superposition of multiple reflected waves developing standing waves within intact blocks,described as superposition resonance.While resonance through superposition has previously been identified,resonance based on masses between springs has not been previously identified in jointed rocks.The findings of this study have implications for future analysis of multiple jointed rock masses,showing that a wave travelling through such materials can induce other modes of propagation of waves,i.e.spring resonance.展开更多
This paper investigates interception missiles’trajectory tracking guidance problem under wind field and external disturbances in the boost phase.Indeed,the velocity control in such trajectory tracking guidance system...This paper investigates interception missiles’trajectory tracking guidance problem under wind field and external disturbances in the boost phase.Indeed,the velocity control in such trajectory tracking guidance systems of missiles is challenging.As our contribution,the velocity control channel is designed to deal with the intractable velocity problem and improve tracking accuracy.The global prescribed performance function,which guarantees the tracking error within the set range and the global convergence of the tracking guidance system,is first proposed based on the traditional PPF.Then,a tracking guidance strategy is derived using the integral sliding mode control techniques to make the sliding manifold and tracking errors converge to zero and avoid singularities.Meanwhile,an improved switching control law is introduced into the designed tracking guidance algorithm to deal with the chattering problem.A back propagation neural network(BPNN)extended state observer(BPNNESO)is employed in the inner loop to identify disturbances.The obtained results indicate that the proposed tracking guidance approach achieves the trajectory tracking guidance objective without and with disturbances and outperforms the existing tracking guidance schemes with the lowest tracking errors,convergence times,and overshoots.展开更多
AIM: To describe the characteristics of modulation transfer function (MTF) of anterior corneal surface, and obtain the the normal reference range of MTF at different spatial frequencies and optical zones of the anteri...AIM: To describe the characteristics of modulation transfer function (MTF) of anterior corneal surface, and obtain the the normal reference range of MTF at different spatial frequencies and optical zones of the anterior corneal surface in myopes. METHODS: Four hundred eyes from 200 patients were examined under SIRIUS corneal topography system. Phoenis analysis software was applied to simulate the MTF curves of anterior corneal surface at vertical and horizontal meridians at the 3, 4, 5, 6, 7mm optical zones of cornea. The MTF values at spatial frequencies of 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55 and 60 cycles/degree (c/d) were selected. RESULTS: The MTF curve of anterior corneal surface decreased rapidly from low to intermediate frequency (0-15cpd) at various optical zones of cornea, the value decreased to 0 slowly at higher frequency (>15cpd). With the increase of the optical zones of cornea, MTF curve decreased gradually. 3) In the range of 3 mm- 6 mm optical zones of the cornea, the MTF values measured at horizontal meridian were greater than the corresponding values at horizontal meridian of each spatial frequency, the difference was statistically significant (P<0.05). At 7 mm optical zones of cornea, the MTF values measured at horizontal meridian were less than the corresponding values at vertical meridian at 10-60 spatial frequencies (cpd), and the difference was statistically significant in 25, 30, 35, 40, 45, 50 cpd(P<0.05). CONCLUSION: MTF can be used to describe the imaging quality of optical systems at anterior corneal surface objectively in detail.展开更多
The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic gr...The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic ground condition. This approach is a direct hit to the atmospheric scattering OTF using the same original context of modulation transfer function （MTF） measurement, i.e., images of sinusoidal grating at different spatial frequencies. Both the amplitude and phase shift of the OTF at various zenith and azimuth angles can be obtained at an arbitrary spatial frequency.展开更多
Based on the fact that the real inductor and the real capacitor are fractional order in nature and the fractional calculus,the transfer function modeling and analysis of the open-loop Buck converter in a continuous co...Based on the fact that the real inductor and the real capacitor are fractional order in nature and the fractional calculus,the transfer function modeling and analysis of the open-loop Buck converter in a continuous conduction mode（CCM） operation are carried out in this paper.The fractional order small signal model and the corresponding equivalent circuit of the open-loop Buck converter in a CCM operation are presented.The transfer functions from the input voltage to the output voltage,from the input voltage to the inductor current,from the duty cycle to the output voltage,from the duty cycle to the inductor current,and the output impedance of the open-loop Buck converter in CCM operation are derived,and their bode diagrams and step responses are calculated,respectively.It is found that all the derived fractional order transfer functions of the system are influenced by the fractional orders of the inductor and the capacitor.Finally,the realization of the fractional order inductor and the fractional order capacitor is designed,and the corresponding PSIM circuit simulation results of the open-loop Buck converter in CCM operation are given to confirm the correctness of the derivations and the theoretical analysis.展开更多
A novel repetitive control strategy for the output waveform of single-phase CVCF inverters is presented. In this scheme, the inverse transfer function of inverter is used as a compensator to obtain stable and satisfy ...A novel repetitive control strategy for the output waveform of single-phase CVCF inverters is presented. In this scheme, the inverse transfer function of inverter is used as a compensator to obtain stable and satisfy harmonic rejection. Besides, PD controller is adopted to improve transient performance. Simulation and experimental results, which are gotten from a DSP-based 400Hz, 5.5KW inverter, indicate that the proposed control scheme can achieve not only low THD during steady-state operation but also fast transient response during load step change.展开更多
The resolution characteristic can be obtained by the modulation transfer function （MTF） of a GaAs/GaA1As photocathode. After establishing the theoretical model of GaAs（100）-oriented atomic configuration and the fo...The resolution characteristic can be obtained by the modulation transfer function （MTF） of a GaAs/GaA1As photocathode. After establishing the theoretical model of GaAs（100）-oriented atomic configuration and the formula for the ionized impurity scattering of the non-equilibrium carriers, this paper calculates the trajectories of photoelectrons in a photocathode. Thus the distribution of photoelectron spots on the emit-face is obtained, which is namely the point spread function. The MTF is obtained by Fourier transfer of the line spread function obtained from the point spread function. The MTF obtained from these calculations is shown to depend heavily on the electron diffusion length, and enhanced considerably by decreasing the electron diffusion length and increasing the doping concentration. Furthermore, the resolution is enhanced considerably by increasing the active-layer thickness, especially at high spatial frequencies. The best spatial resolution is 860 lp/mm, for the GaAs photocathode of doping concentration 1 ×10^19 cm 3 electron diffusion length 3.6 μm and the active-layer thickness 2 μm, under the 633-nm light irradiated. This research will contribute to the future improvement of the cathode＇s resolution for preparing a high performance GaAs photocathode, and improve the resolution of a low light level image intensifier.展开更多
In this paper, the normal Luenberger function observer design for second-order descriptor linear systems is considered. It is shown that the main procedure of the design is to solve a so-called second-order generalize...In this paper, the normal Luenberger function observer design for second-order descriptor linear systems is considered. It is shown that the main procedure of the design is to solve a so-called second-order generalized Sylvester-observer matrix equation. Based on an explicit parametric solution to this equation, a parametric solution to the normal Luenberger function observer design problem is given. The design degrees of freedom presented by explicit parameters can be further utilized to achieve some additional design requirements.展开更多
The fluctuation of most of the hydrograph in the deep aqueous system records the fluid pulsation in lithosphere and variation of the earth's crust. Many observations have verified that groundwater is an ideal info...The fluctuation of most of the hydrograph in the deep aqueous system records the fluid pulsation in lithosphere and variation of the earth's crust. Many observations have verified that groundwater is an ideal information carrier of the crust. In this paper, the series of input (precipitation, air pressure, Earth tide etc.) and output (water level, artesian flow) of the deep aqueous system are studied by using the spectrum analysis and system theory. The application concepts of transfer function and the spectral structure of the hydrograph enrich the knowledge of the deep aqueous system. Two typical spectral structures of the hydrograph of the deep aqueous system are obtained by comparing with many water-bearing systems of the Jizhong depression. One is from well Ma-17 and the other is from the well Xinze-5. Finally, the physical models of forming the spectrum of the hydrograph are constructed on the basis of the spectrum research on the deep aqueous system.展开更多
To understand the relationship between planktonic diatoms and environmental variables in the lakes on the Songnen Plain,northeast(NE)China,we investigated water quality and planktonic diatoms from 71 sampling points i...To understand the relationship between planktonic diatoms and environmental variables in the lakes on the Songnen Plain,northeast(NE)China,we investigated water quality and planktonic diatoms from 71 sampling points in 27 lakes,based on which Canonical Correspondence Analysis(CCA)was conducted.The result show that planktonic diatoms displayed certain responses to environment gradients,and the total phosphorus(TP)explained the maximum variation of planktonic diatom species among the 15 environmental variables,suggesting that TP was the most important and significant environmental parameter affecting the distribution of diatom species.In addition,we established a diatom-total phosphorus transfer(DTPT)function,of which component 5 of the weighted averaging partial least squares regression(WAPLS)was chosen to and compared with a series of weighted average regression(WA)models and WA-PLS models.According to the jackknifing statistical test,the component 5 of WA-PLS models provided a lower root-mean-square error prediction(RMSEP=0.202)and a higher correlation coefficient between observation and prediction(R^2_Jack=0.759).After deletion of three outliers,the root-mean-square error prediction of the DTPT function was reduced(RMSEP=0.169)while the correlation coefficient between observation and prediction was increased(R^2_Jack=0.823).Therefore,this DTPT function performed better than other regional TP models in the world.However,it remains demanding for expanding the background dataset to improve the prediction ability of the model.展开更多
The galvanic coupling intra-body communication （IBC） was mathematically simulated based on the proposed transfer function. Firstly, a galvanic coupling IBC circuit model was developed and the corresponding parameter...The galvanic coupling intra-body communication （IBC） was mathematically simulated based on the proposed transfer function. Firstly, a galvanic coupling IBC circuit model was developed and the corresponding parameters were discussed. Secondly, the transfer function of the galvanic coupling IBC was derived and proposed. Finally, the signal attenuation characteristics of the galvanic coupling IBC were measured along different signal transmission paths of actual human bodies, while the corresponding mathematical simulations based on the proposed transfer function were carried out. Our investigation showed that the mathematical simulation results coincided with the measured results over the frequency range of 100kHz to 5MHz, which indicated that the proposed transfer function could be useful for theoretical analysis and application of the galvanic coupling IBC.展开更多
A simple method for disturbance decoupling for matrix second-order linear systems is proposed directly in matrix second-order framework via Luenberger function observers based on complete parametric eigenstructure ass...A simple method for disturbance decoupling for matrix second-order linear systems is proposed directly in matrix second-order framework via Luenberger function observers based on complete parametric eigenstructure assignment. By introducing the H2 norm of the transfer function from disturbance to estimation error, sufficient and necessary conditions for disturbance decoupling in matrix second-order linear systems are established and are arranged into constraints on the design parameters via Luenberger function observers in terms of the closed-loop eigenvalues and the group of design parameters provided by the eigenstructure assignment approach. Therefore, the disturbance decoupling problem is converted into an eigenstructure assignment problem with extra parameter constraints. A simple example is investigated to show the effect and simplicity of the approach.展开更多
An optical transfer function （OTF） reconstruction model is first embedded into incoherent Fourier ptychography （IFP）. The leading result is a proposed algorithm that can recover both the super-resolution image and...An optical transfer function （OTF） reconstruction model is first embedded into incoherent Fourier ptychography （IFP）. The leading result is a proposed algorithm that can recover both the super-resolution image and the OTF of an imaging system with unknown aberrations simultaneously. This model overcomes the difficult problem of OTF estimation that the previous IFP faces. The effectiveness of this algorithm is demonstrated by numerical simulations, and the superior reconstruction is presented. We believe that the reported algorithm can extend the original IFP for more complex conditions and may provide a solution by using structured light for characterization of optical systems＇ aberrations.展开更多
A new interpolation algorithm for Head-Related Transfer Function （HRTF） is proposed to realize 3D sound reproduction via headphones in arbitrary spatial direction. HRTFs are modeled as a weighted sum of spherical ha...A new interpolation algorithm for Head-Related Transfer Function （HRTF） is proposed to realize 3D sound reproduction via headphones in arbitrary spatial direction. HRTFs are modeled as a weighted sum of spherical harmonics on a spherical surface. Truncated Singular Value Decomposition （SVD） is adopted to calculate the weights of the model. The truncation number is chosen according to Frobenius norm ratio and the partial condition number. Compared with other interpolated methods, our proposed approach not only is continuous but exploits global information of available directions. The HRTF from any desired direction can be and interpolated results demonstrate that our obtained more accurately and robustly. Reconstructed proposed algorithm acquired better performance.展开更多
Accurately measuring precipitation is integral for understanding water cycle processes and assessing climate change in the Qinghai–Tibet Plateau(QTP).The Geonor T-200B weighing precipitation gauge with a single Alter...Accurately measuring precipitation is integral for understanding water cycle processes and assessing climate change in the Qinghai–Tibet Plateau(QTP).The Geonor T-200B weighing precipitation gauge with a single Alter shield(Geonor)and the Chinese standard precipitation gauge(CSPG)are widely used for measuring precipitation in the QTP.However,their measurements need to be adjusted for wetting loss,evaporation loss and windinduced undercatch.Four existing transfer functions for adjusting the Geonor-recorded and three transfer functions for adjusting the CSPG-recorded precipitation at hourly,daily or event scale has been proposed based on the precipitation intercomparison experiments conducted at a single site in different regions.Two latest transfer functions for the Geonor(which are referred to as K2017a and K2017b)at the half-hour time scale based on the precipitation intercomparison experiments at multiple stations in the northern hemisphere were provided in the World Meteorological Organization Solid Precipitation Intercomparison Experiment.However,the applicability of these transfer functions in the QTP has not been evaluated.Therefore,the current study carried out a precipitation measurement intercomparison experiment between August 2018 and September 2020 at a site in Beiluhe in central QTP.The performance of these transfer functions at this site was also evaluated on the basis of mean bias(MB),root mean squared error(RMSE)and relative total catch(RTC).The results are as follows:First,the unadjusted RTC values of the Geonor for rain,mixed(snow mixed with rain),snow and hail are 92.06%,85.35%,64.11% and 91.82%,respectively,and the unadjusted RTC values of the CSPG for the same precipitation types are 92.59%,81.32%,46.43% and 95.56%,respectively.Second,K2017a has the most accurate adjustment results for the Geonor-recorded snow and mixed precipitation at the half-hour time scale,and the post-adjustment RTC values increased to 98.25% and 98.23%,respectively.M2007e,an event-based transfer function,was found to have the most accurate adjustment results for the Geonorrecorded snow precipitation at the event scale,and the post-adjustment RTC value increased to 96.36%.Third,the existing transfer functions for CSPG underestimate snowfall,while overestimating rainfall.Fourth,hail is a significant precipitation type in central QTP.The catch efficiency of hail precipitation and the temperature when hail precipitation occurs are close to those of rain;moreover,the transfer functions for rain are suitable for hail as well.展开更多
FBS-3A feedback broadband seismometer has been widely utilized in observation networks up to now. Therefore, it is very important and practically meaningful for the application of this kind of sensor to fulfill some r...FBS-3A feedback broadband seismometer has been widely utilized in observation networks up to now. Therefore, it is very important and practically meaningful for the application of this kind of sensor to fulfill some relative research work about its transfer function and for the analysis to the data recorded and the further development of the seismometer. In this paper, from the viewpoint of achieving its working principle, method of systematic analysis is applied to deduce the transfer functions, including both the transfer function for calibration and that for measurement. Moreover, on the basis of that, the distribution of its zeroes and poles in a complex frequency domain is analyzed, which provides a convincing evidence to simplify this seismometer system from a high-order one to a two-order one. And the emulation of the frequency characteristics of FBS-3A is presented in this paper. On the whole, the aim of this article is to do some theoretical work about the earthquake observation sensor, and also to introduce the method of making systematic analysis in a complex frequency domain to the research and the development of the seismometers.展开更多
AIM:To analyze the retinal modulation transfer function between amblyopes whose visual acuity was corrected to 5.0 and normal subjects at the same age. METHODS: RM-800 used to detect contrast sensitivity was adopted t...AIM:To analyze the retinal modulation transfer function between amblyopes whose visual acuity was corrected to 5.0 and normal subjects at the same age. METHODS: RM-800 used to detect contrast sensitivity was adopted to measure MTF of 96 amblyopes (96 eyes) whose visual acuity was corrected to 5.0 and 80 normal controls (80 eyes) at the same age under six interference fringes (IVA=0.06, 0.1, 0.2, 0.4, 0.6, 0.8). RESULTS: The functional values of amblyopes were significantly lower than those of normal subjects in every fringe (P<0.01), especially in medium and high frequency. CONCLUSION: For amblyopes, MTF was still abnormal after stopping the treatments.展开更多
In previous and this studies it appears that the linear and nonlinear wave theory-can not accurately and easily predict the water particle velocities: Therefore, different from the theoretical considerations, in this ...In previous and this studies it appears that the linear and nonlinear wave theory-can not accurately and easily predict the water particle velocities: Therefore, different from the theoretical considerations, in this study we have attempted to determine the transfer function empirically. Laboratory experiments were performed under various wave conditions. The empirical formulas of the transfer function of the wave height, angular frequency and water particle velocity were obtained on the basis of these test data by dimensional analysis and regression analysis. In intermediate and deep water depth conditions, the transfer function was only a function of a nondimensional parameter which is composed of the angular frequency, the depth of the velocity gauge under the still water level, water depth and the acceleration of gravity. Finally, the empirical formulas were compared with experimental data and observational data form present and Cavaleri's (1978) studies. The empirical formulas were found to be in sufficient correltion with these data.展开更多
基金funding support from the Israeli Ministry of Housing and Construction(Grant No.2028286).
文摘Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most of which are based on the global rock bolt response evaluated in pull-out tests.This paper presents a laboratory experimental setup aiming to capture the rock formation effect,while using distributed fiber optic sensing to quantify the effect of the confinement and the reinforcement pull-out behavior on a more local level.It is shown that the behavior along the sample itself varies,with certain points exhibiting stress drops with crack formation.Some edge effects related to the kinematic freedom of the grout to dilate are also observed.Regardless,it was found that the mid-level response is quite similar to the average response along the sample.The ability to characterize the variation of the response along the sample is one of the many advantages high-resolution fiber optic sensing allows in such investigations.The paper also offers a plasticity-based hardening load transfer function,representing a"slice"of the anchor.The paper describes in detail the development of the model and the calibration/determination of its parameters.The suggested model captures well the coupled behavior in which the pull-out process leads to an increase in the confining stress due to dilative behavior.
基金supported by the Engineering and Physical Sciences Research Council(EPSRC)(EP/R513258/1).
文摘Resonance effects in parallel jointed rocks subject to stress waves are investigated using transfer functions,derived from signals generated through numerical modelling.Resonance is important for a range of engineering situations as it identifies the frequency of waves which will be favourably transmitted.Two different numerical methods are used for this study,adopting the finite difference method and the combined discrete element-finite difference method.The numerical models are validated by replicating results from previous studies.The two methods are found to behave similarly and show the same resonance effects;one operating at low frequency and the other operating at relatively high frequency.These resonance effects are interpreted in terms of simple physical systems and analytical equations are derived to predict the resonant frequencies of complex rock masses.Low frequency resonance is shown to be generated by a system synonymous with masses between springs,described as spring resonance,with an equal number of resonant frequencies as the number of blocks.High frequency resonance is generated through superposition of multiple reflected waves developing standing waves within intact blocks,described as superposition resonance.While resonance through superposition has previously been identified,resonance based on masses between springs has not been previously identified in jointed rocks.The findings of this study have implications for future analysis of multiple jointed rock masses,showing that a wave travelling through such materials can induce other modes of propagation of waves,i.e.spring resonance.
基金the National Natural Science Foundation of China(Grant No.12072090).
文摘This paper investigates interception missiles’trajectory tracking guidance problem under wind field and external disturbances in the boost phase.Indeed,the velocity control in such trajectory tracking guidance systems of missiles is challenging.As our contribution,the velocity control channel is designed to deal with the intractable velocity problem and improve tracking accuracy.The global prescribed performance function,which guarantees the tracking error within the set range and the global convergence of the tracking guidance system,is first proposed based on the traditional PPF.Then,a tracking guidance strategy is derived using the integral sliding mode control techniques to make the sliding manifold and tracking errors converge to zero and avoid singularities.Meanwhile,an improved switching control law is introduced into the designed tracking guidance algorithm to deal with the chattering problem.A back propagation neural network(BPNN)extended state observer(BPNNESO)is employed in the inner loop to identify disturbances.The obtained results indicate that the proposed tracking guidance approach achieves the trajectory tracking guidance objective without and with disturbances and outperforms the existing tracking guidance schemes with the lowest tracking errors,convergence times,and overshoots.
文摘AIM: To describe the characteristics of modulation transfer function (MTF) of anterior corneal surface, and obtain the the normal reference range of MTF at different spatial frequencies and optical zones of the anterior corneal surface in myopes. METHODS: Four hundred eyes from 200 patients were examined under SIRIUS corneal topography system. Phoenis analysis software was applied to simulate the MTF curves of anterior corneal surface at vertical and horizontal meridians at the 3, 4, 5, 6, 7mm optical zones of cornea. The MTF values at spatial frequencies of 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55 and 60 cycles/degree (c/d) were selected. RESULTS: The MTF curve of anterior corneal surface decreased rapidly from low to intermediate frequency (0-15cpd) at various optical zones of cornea, the value decreased to 0 slowly at higher frequency (>15cpd). With the increase of the optical zones of cornea, MTF curve decreased gradually. 3) In the range of 3 mm- 6 mm optical zones of the cornea, the MTF values measured at horizontal meridian were greater than the corresponding values at horizontal meridian of each spatial frequency, the difference was statistically significant (P<0.05). At 7 mm optical zones of cornea, the MTF values measured at horizontal meridian were less than the corresponding values at vertical meridian at 10-60 spatial frequencies (cpd), and the difference was statistically significant in 25, 30, 35, 40, 45, 50 cpd(P<0.05). CONCLUSION: MTF can be used to describe the imaging quality of optical systems at anterior corneal surface objectively in detail.
基金supported by the Main Direction Program of Knowledge Innovation of Chinese Academy of Sciences(Grant No.KGFZD-125-13-006)
文摘The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic ground condition. This approach is a direct hit to the atmospheric scattering OTF using the same original context of modulation transfer function （MTF） measurement, i.e., images of sinusoidal grating at different spatial frequencies. Both the amplitude and phase shift of the OTF at various zenith and azimuth angles can be obtained at an arbitrary spatial frequency.
基金Project supported by the National Natural Science Foundation of China (Grant No. 51007068)the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20100201120028)+2 种基金the Natural Science Basic Research Plan in Shaanxi Province of China (Grant No. 2012JQ7026)the Fundamental Research Funds for the Central Universities of China (Grant No. 2012jdgz09)the State Key Laboratory of Electrical Insulation and Power Equipment of China (Grant No. EIPE12303)
文摘Based on the fact that the real inductor and the real capacitor are fractional order in nature and the fractional calculus,the transfer function modeling and analysis of the open-loop Buck converter in a continuous conduction mode（CCM） operation are carried out in this paper.The fractional order small signal model and the corresponding equivalent circuit of the open-loop Buck converter in a CCM operation are presented.The transfer functions from the input voltage to the output voltage,from the input voltage to the inductor current,from the duty cycle to the output voltage,from the duty cycle to the inductor current,and the output impedance of the open-loop Buck converter in CCM operation are derived,and their bode diagrams and step responses are calculated,respectively.It is found that all the derived fractional order transfer functions of the system are influenced by the fractional orders of the inductor and the capacitor.Finally,the realization of the fractional order inductor and the fractional order capacitor is designed,and the corresponding PSIM circuit simulation results of the open-loop Buck converter in CCM operation are given to confirm the correctness of the derivations and the theoretical analysis.
基金This work was supported by the National Natural Science Foundation of China (No. 50007004)
文摘A novel repetitive control strategy for the output waveform of single-phase CVCF inverters is presented. In this scheme, the inverse transfer function of inverter is used as a compensator to obtain stable and satisfy harmonic rejection. Besides, PD controller is adopted to improve transient performance. Simulation and experimental results, which are gotten from a DSP-based 400Hz, 5.5KW inverter, indicate that the proposed control scheme can achieve not only low THD during steady-state operation but also fast transient response during load step change.
基金Project supported by the National Natural Science Foundation of China (Grant No. 60678043)the Research and Innovation Plan for Graduate Students of Jiangsu Higher Education Institutions,China (Grant No. CX09B 096Z)
文摘The resolution characteristic can be obtained by the modulation transfer function （MTF） of a GaAs/GaA1As photocathode. After establishing the theoretical model of GaAs（100）-oriented atomic configuration and the formula for the ionized impurity scattering of the non-equilibrium carriers, this paper calculates the trajectories of photoelectrons in a photocathode. Thus the distribution of photoelectron spots on the emit-face is obtained, which is namely the point spread function. The MTF is obtained by Fourier transfer of the line spread function obtained from the point spread function. The MTF obtained from these calculations is shown to depend heavily on the electron diffusion length, and enhanced considerably by decreasing the electron diffusion length and increasing the doping concentration. Furthermore, the resolution is enhanced considerably by increasing the active-layer thickness, especially at high spatial frequencies. The best spatial resolution is 860 lp/mm, for the GaAs photocathode of doping concentration 1 ×10^19 cm 3 electron diffusion length 3.6 μm and the active-layer thickness 2 μm, under the 633-nm light irradiated. This research will contribute to the future improvement of the cathode＇s resolution for preparing a high performance GaAs photocathode, and improve the resolution of a low light level image intensifier.
基金This work was supported by National Natural Science Foundation of China(No.60710002)Program for Changjiang Scholars and Innovative Research Team in University(PCSIRT).
文摘In this paper, the normal Luenberger function observer design for second-order descriptor linear systems is considered. It is shown that the main procedure of the design is to solve a so-called second-order generalized Sylvester-observer matrix equation. Based on an explicit parametric solution to this equation, a parametric solution to the normal Luenberger function observer design problem is given. The design degrees of freedom presented by explicit parameters can be further utilized to achieve some additional design requirements.
基金Project was support by National Natural Science Foundation of China.
文摘The fluctuation of most of the hydrograph in the deep aqueous system records the fluid pulsation in lithosphere and variation of the earth's crust. Many observations have verified that groundwater is an ideal information carrier of the crust. In this paper, the series of input (precipitation, air pressure, Earth tide etc.) and output (water level, artesian flow) of the deep aqueous system are studied by using the spectrum analysis and system theory. The application concepts of transfer function and the spectral structure of the hydrograph enrich the knowledge of the deep aqueous system. Two typical spectral structures of the hydrograph of the deep aqueous system are obtained by comparing with many water-bearing systems of the Jizhong depression. One is from well Ma-17 and the other is from the well Xinze-5. Finally, the physical models of forming the spectrum of the hydrograph are constructed on the basis of the spectrum research on the deep aqueous system.
基金Supported by the National Natural Science Foundation of China(Nos.41571199,41030743,31870187)。
文摘To understand the relationship between planktonic diatoms and environmental variables in the lakes on the Songnen Plain,northeast(NE)China,we investigated water quality and planktonic diatoms from 71 sampling points in 27 lakes,based on which Canonical Correspondence Analysis(CCA)was conducted.The result show that planktonic diatoms displayed certain responses to environment gradients,and the total phosphorus(TP)explained the maximum variation of planktonic diatom species among the 15 environmental variables,suggesting that TP was the most important and significant environmental parameter affecting the distribution of diatom species.In addition,we established a diatom-total phosphorus transfer(DTPT)function,of which component 5 of the weighted averaging partial least squares regression(WAPLS)was chosen to and compared with a series of weighted average regression(WA)models and WA-PLS models.According to the jackknifing statistical test,the component 5 of WA-PLS models provided a lower root-mean-square error prediction(RMSEP=0.202)and a higher correlation coefficient between observation and prediction(R^2_Jack=0.759).After deletion of three outliers,the root-mean-square error prediction of the DTPT function was reduced(RMSEP=0.169)while the correlation coefficient between observation and prediction was increased(R^2_Jack=0.823).Therefore,this DTPT function performed better than other regional TP models in the world.However,it remains demanding for expanding the background dataset to improve the prediction ability of the model.
基金Supported by the National Natural Science Foundation of China(60801050)the Basic Research Foundation of Beijing Institute of Technology(1010050320804)
文摘The galvanic coupling intra-body communication （IBC） was mathematically simulated based on the proposed transfer function. Firstly, a galvanic coupling IBC circuit model was developed and the corresponding parameters were discussed. Secondly, the transfer function of the galvanic coupling IBC was derived and proposed. Finally, the signal attenuation characteristics of the galvanic coupling IBC were measured along different signal transmission paths of actual human bodies, while the corresponding mathematical simulations based on the proposed transfer function were carried out. Our investigation showed that the mathematical simulation results coincided with the measured results over the frequency range of 100kHz to 5MHz, which indicated that the proposed transfer function could be useful for theoretical analysis and application of the galvanic coupling IBC.
文摘A simple method for disturbance decoupling for matrix second-order linear systems is proposed directly in matrix second-order framework via Luenberger function observers based on complete parametric eigenstructure assignment. By introducing the H2 norm of the transfer function from disturbance to estimation error, sufficient and necessary conditions for disturbance decoupling in matrix second-order linear systems are established and are arranged into constraints on the design parameters via Luenberger function observers in terms of the closed-loop eigenvalues and the group of design parameters provided by the eigenstructure assignment approach. Therefore, the disturbance decoupling problem is converted into an eigenstructure assignment problem with extra parameter constraints. A simple example is investigated to show the effect and simplicity of the approach.
基金Supported by the National Natural Science Foundation of China under Grant No 61205144the Research Project of National University of Defense Technology under Grant No JC13-07-01the Key Laboratory of High Power Laser and Physics of Chinese Academy of Sciences
文摘An optical transfer function （OTF） reconstruction model is first embedded into incoherent Fourier ptychography （IFP）. The leading result is a proposed algorithm that can recover both the super-resolution image and the OTF of an imaging system with unknown aberrations simultaneously. This model overcomes the difficult problem of OTF estimation that the previous IFP faces. The effectiveness of this algorithm is demonstrated by numerical simulations, and the superior reconstruction is presented. We believe that the reported algorithm can extend the original IFP for more complex conditions and may provide a solution by using structured light for characterization of optical systems＇ aberrations.
基金Supported by Shanghai Natural Science Foundation, Shanghai Leading Academic Discipline Project, and STCSM of China (No. 08ZR1408300, S30108, and 08DZ2231100)
文摘A new interpolation algorithm for Head-Related Transfer Function （HRTF） is proposed to realize 3D sound reproduction via headphones in arbitrary spatial direction. HRTFs are modeled as a weighted sum of spherical harmonics on a spherical surface. Truncated Singular Value Decomposition （SVD） is adopted to calculate the weights of the model. The truncation number is chosen according to Frobenius norm ratio and the partial condition number. Compared with other interpolated methods, our proposed approach not only is continuous but exploits global information of available directions. The HRTF from any desired direction can be and interpolated results demonstrate that our obtained more accurately and robustly. Reconstructed proposed algorithm acquired better performance.
基金supported primarily by the National Natural Sciences Foundation of China(42171467,42001060 and 41705139)Natural Science Foundation of Qinghai Province(2021-ZJ947Q)。
文摘Accurately measuring precipitation is integral for understanding water cycle processes and assessing climate change in the Qinghai–Tibet Plateau(QTP).The Geonor T-200B weighing precipitation gauge with a single Alter shield(Geonor)and the Chinese standard precipitation gauge(CSPG)are widely used for measuring precipitation in the QTP.However,their measurements need to be adjusted for wetting loss,evaporation loss and windinduced undercatch.Four existing transfer functions for adjusting the Geonor-recorded and three transfer functions for adjusting the CSPG-recorded precipitation at hourly,daily or event scale has been proposed based on the precipitation intercomparison experiments conducted at a single site in different regions.Two latest transfer functions for the Geonor(which are referred to as K2017a and K2017b)at the half-hour time scale based on the precipitation intercomparison experiments at multiple stations in the northern hemisphere were provided in the World Meteorological Organization Solid Precipitation Intercomparison Experiment.However,the applicability of these transfer functions in the QTP has not been evaluated.Therefore,the current study carried out a precipitation measurement intercomparison experiment between August 2018 and September 2020 at a site in Beiluhe in central QTP.The performance of these transfer functions at this site was also evaluated on the basis of mean bias(MB),root mean squared error(RMSE)and relative total catch(RTC).The results are as follows:First,the unadjusted RTC values of the Geonor for rain,mixed(snow mixed with rain),snow and hail are 92.06%,85.35%,64.11% and 91.82%,respectively,and the unadjusted RTC values of the CSPG for the same precipitation types are 92.59%,81.32%,46.43% and 95.56%,respectively.Second,K2017a has the most accurate adjustment results for the Geonor-recorded snow and mixed precipitation at the half-hour time scale,and the post-adjustment RTC values increased to 98.25% and 98.23%,respectively.M2007e,an event-based transfer function,was found to have the most accurate adjustment results for the Geonorrecorded snow precipitation at the event scale,and the post-adjustment RTC value increased to 96.36%.Third,the existing transfer functions for CSPG underestimate snowfall,while overestimating rainfall.Fourth,hail is a significant precipitation type in central QTP.The catch efficiency of hail precipitation and the temperature when hail precipitation occurs are close to those of rain;moreover,the transfer functions for rain are suitable for hail as well.
文摘FBS-3A feedback broadband seismometer has been widely utilized in observation networks up to now. Therefore, it is very important and practically meaningful for the application of this kind of sensor to fulfill some relative research work about its transfer function and for the analysis to the data recorded and the further development of the seismometer. In this paper, from the viewpoint of achieving its working principle, method of systematic analysis is applied to deduce the transfer functions, including both the transfer function for calibration and that for measurement. Moreover, on the basis of that, the distribution of its zeroes and poles in a complex frequency domain is analyzed, which provides a convincing evidence to simplify this seismometer system from a high-order one to a two-order one. And the emulation of the frequency characteristics of FBS-3A is presented in this paper. On the whole, the aim of this article is to do some theoretical work about the earthquake observation sensor, and also to introduce the method of making systematic analysis in a complex frequency domain to the research and the development of the seismometers.
基金Supported by Wenzhou Science and Technology Commission in 2009, China (No.Y20090384)
文摘AIM:To analyze the retinal modulation transfer function between amblyopes whose visual acuity was corrected to 5.0 and normal subjects at the same age. METHODS: RM-800 used to detect contrast sensitivity was adopted to measure MTF of 96 amblyopes (96 eyes) whose visual acuity was corrected to 5.0 and 80 normal controls (80 eyes) at the same age under six interference fringes (IVA=0.06, 0.1, 0.2, 0.4, 0.6, 0.8). RESULTS: The functional values of amblyopes were significantly lower than those of normal subjects in every fringe (P<0.01), especially in medium and high frequency. CONCLUSION: For amblyopes, MTF was still abnormal after stopping the treatments.
文摘In previous and this studies it appears that the linear and nonlinear wave theory-can not accurately and easily predict the water particle velocities: Therefore, different from the theoretical considerations, in this study we have attempted to determine the transfer function empirically. Laboratory experiments were performed under various wave conditions. The empirical formulas of the transfer function of the wave height, angular frequency and water particle velocity were obtained on the basis of these test data by dimensional analysis and regression analysis. In intermediate and deep water depth conditions, the transfer function was only a function of a nondimensional parameter which is composed of the angular frequency, the depth of the velocity gauge under the still water level, water depth and the acceleration of gravity. Finally, the empirical formulas were compared with experimental data and observational data form present and Cavaleri's (1978) studies. The empirical formulas were found to be in sufficient correltion with these data.
