The microstructure evolution during strain induced ferrite transformation was followed in thermal-simulation tests of clean 08 and 20Mn steels. The influences of carbon equivalence and initial austenite grain size on ...The microstructure evolution during strain induced ferrite transformation was followed in thermal-simulation tests of clean 08 and 20Mn steels. The influences of carbon equivalence and initial austenite grain size on ferrite grain refinement and the volume fraction of ferrite during straining were inspected. The results revealed that the accelerating effect of ferrite transformation by strain was increased as the carbon equivalence decreased. However, finer ferrite grains were obtained at higher carbon content. At strain of similar to1.5 ferrite grains less than 3 mum and 2 mum can be obtained in 08 and 20Mn steels respectively. Whereas the ferrite grain refinement in 08 steel was due to both effects of strain induced transformation and ferrite dynamic recrystallization, that in 20Mn was mainly due to strain induced transformation. Heavy strain can produce fine ferrite grains in coarse austenite grained 08 steel, but it would lead to band microstructure in coarse austenite grained 20Mn.展开更多
Grain refinement is one of the effective methods to develop new generation low carbon microalloyed steels possessing excellent combination of mechanical properties. The microstructural evolution and ferrite grain refi...Grain refinement is one of the effective methods to develop new generation low carbon microalloyed steels possessing excellent combination of mechanical properties. The microstructural evolution and ferrite grain refinement at the deformation temperature of 865℃, above Ar3, with different strain rates were investigated using single pass isothermal hot compression experiments for a low carbon Nb-Ti microalloyed steel. The physical processes that occurred during deformation were discussed by observing the optical microstructure and analyzing the true stress-true strain responses. At strain rates of 0.001 and 0.01s^-1, there is no evidence of work hardening behavior during hot deformation and strain-induced transformation （SIT） leads to dynamic flow softening in flow curves. Optical microscopy observation shows that ultrafine and equiaxed ferrite with grain sizes of 2μm can be obtained by applying deformation with strain rate of 0.1 s^-1 due to SIT just after deformation. Furthermore, increasing the strain rate from 0.001 to 0.1 s^-1 reduces both the grain size of the equiaxed ferrite and the amount of deformed ferrite.展开更多
The effects of applied tensile strain on the coherent α_2→O-phase transformation in Ti-Al-Nb alloys are explored bycomputer simulation using a phase-field method. The focus is on the influence of the applied strain ...The effects of applied tensile strain on the coherent α_2→O-phase transformation in Ti-Al-Nb alloys are explored bycomputer simulation using a phase-field method. The focus is on the influence of the applied strain direction onthe microstructure and volume fraction of the O-phase precipitates. It is found that altering applied strain directioncan modify microstructure of Ti-25Al-10～12Nb (at. pct) alloy during α_2→O-phase transformation effectively andfull laminate microstructure in the Ti-25Al-10Nb (at. pct) alloy can be realized by an applied strain only along thedirection 30°away from the α_2 phase <1010> in magnitude equivalent to the stress-free transformation strain. Thesimulation also shows that not only the magnitude of applied strain but also the applied strain direction influencesthe O-phase volume fraction and the effect of strain direction on the volume fraction is up to 25%.展开更多
The influence of deforming temperature on ferrite refinement was analyzed by comparing the microstructures obtained by deformation at above A(r3), in two-phase region of (alpha + gamma) and at below A(t) in clean 08 a...The influence of deforming temperature on ferrite refinement was analyzed by comparing the microstructures obtained by deformation at above A(r3), in two-phase region of (alpha + gamma) and at below A(t) in clean 08 and 20Mn steels. The results indicate that ferrite refinement through strain induced transformation by deformation at above A(r3) is more effective than that by deformation simply through ferrite dynamic recrystallization. The main problem of ferrite refinement by deformation at below A(r3) is the inhomogeneity of microstructure which is controlled by the orientations and sizes of ferrite grains and the distribution of second phases. Ferrite dynamic recrystallization after strain induced transformation can further effectively refine ferrite.展开更多
The effects of large strain and strain path reversal on the deformation microstructure evolution in austenite below the recrystallisation temperature were studied by hot torsion using a non-transforming Fe-30wt%Ni mod...The effects of large strain and strain path reversal on the deformation microstructure evolution in austenite below the recrystallisation temperature were studied by hot torsion using a non-transforming Fe-30wt%Ni model austenitic alloy.Results show that the high angle boundaries (HABs) can be generated by both microstructure mechanism through dislocation accumulation and texture mechanism via subgrain rotation.However,multiple strain path reversals lead to less well-developed HABs in the original grains compared to single reversal deformed to the same amount of total accumulative strain.This effect is attributed to the subgrain rotation mechanism being less effective at small strains.In comparison,the same hot torsion tests were conducted using a microalloyed steel at a temperature between Ae 3 and Ar 3.After single strain path reversal,substantial deformation-induced austenite-to-ferrite phase transformation was observed.Meanwhile,a test with multiple strain path reversals but with the same total strain produces much lower levels of strain-induced ferrite formation.This difference is correlated to the observations made in the Fe-30wt%Ni model alloy.It is believed that the different amount of strain-induced ferrite originated from the different levels of strain-induced HABs within the austenite which act as ferrite nucleation sites.展开更多
Vanadium dioxide (VO_(2)) has emerged as a promising micro-actuator material for its large amplitude and high work density across the transition between the insulating (M_(1) and M_(2)) and metallic (R) phase. Even th...Vanadium dioxide (VO_(2)) has emerged as a promising micro-actuator material for its large amplitude and high work density across the transition between the insulating (M_(1) and M_(2)) and metallic (R) phase. Even though M_(2)–R transition offers about 70% higher transformation stress than M_(1)–R structural phase transition, the application of the M_(2) phase in the micro-actuators is hindered by the fact that previously, M_(2) phase can only stay stable under tensile stress. In this work, we propose and verify that by synthesizing the VO_(2) nanowires under optimized oxygen-rich conditions, stoichiometry change can be introduced into the nanowires (NWs) which in turn yield a large number free-standing single-crystalline M_(2)-phase NWs stable at room temperature. In addition, we demonstrate that the output stress of the M_(2)-phase NWs is about 65% higher than that of the M_(1)-phase NWs during their transition to R phase, quite close to the theoretical prediction. Our findings open new avenues towards enhancing the performance of VO_(2)-based actuators by using M_(2)–R transition.展开更多
Hot torsion testing was performed on a low carbon Nb-Ti microalloyed steel to study the effects of hot tor- sion parameters, strain and strain rate, on ultrafine ferrite grains production through dynamic strain-induce...Hot torsion testing was performed on a low carbon Nb-Ti microalloyed steel to study the effects of hot tor- sion parameters, strain and strain rate, on ultrafine ferrite grains production through dynamic strain-induced trans- formation, at a deformation temperature just above At3. The initiation and evolution of ultrafine ferrite grains were studied. The results show that the amount of strain and strain rate has conversely effect on the volume fraction and grain size of ultrafine ferrite grains. With increasing strain, the interior of austenite grains become activated as nucle- ation sites for fine ferrite grains. As a result, ferrite grains continuously nucleate not only at the former austenite grain boundaries but also inside the austenite grains which leads to a rapid increase in volume fraction of ultrafine grains. Increasing of strain rate reduces the tendency of ferrite grains coarsening so that ultrafine ferrite grains are achieved, while the volume fraction of ultrafine grains decreases at the same strain level.展开更多
文摘The microstructure evolution during strain induced ferrite transformation was followed in thermal-simulation tests of clean 08 and 20Mn steels. The influences of carbon equivalence and initial austenite grain size on ferrite grain refinement and the volume fraction of ferrite during straining were inspected. The results revealed that the accelerating effect of ferrite transformation by strain was increased as the carbon equivalence decreased. However, finer ferrite grains were obtained at higher carbon content. At strain of similar to1.5 ferrite grains less than 3 mum and 2 mum can be obtained in 08 and 20Mn steels respectively. Whereas the ferrite grain refinement in 08 steel was due to both effects of strain induced transformation and ferrite dynamic recrystallization, that in 20Mn was mainly due to strain induced transformation. Heavy strain can produce fine ferrite grains in coarse austenite grained 08 steel, but it would lead to band microstructure in coarse austenite grained 20Mn.
文摘Grain refinement is one of the effective methods to develop new generation low carbon microalloyed steels possessing excellent combination of mechanical properties. The microstructural evolution and ferrite grain refinement at the deformation temperature of 865℃, above Ar3, with different strain rates were investigated using single pass isothermal hot compression experiments for a low carbon Nb-Ti microalloyed steel. The physical processes that occurred during deformation were discussed by observing the optical microstructure and analyzing the true stress-true strain responses. At strain rates of 0.001 and 0.01s^-1, there is no evidence of work hardening behavior during hot deformation and strain-induced transformation （SIT） leads to dynamic flow softening in flow curves. Optical microscopy observation shows that ultrafine and equiaxed ferrite with grain sizes of 2μm can be obtained by applying deformation with strain rate of 0.1 s^-1 due to SIT just after deformation. Furthermore, increasing the strain rate from 0.001 to 0.1 s^-1 reduces both the grain size of the equiaxed ferrite and the amount of deformed ferrite.
文摘The effects of applied tensile strain on the coherent α_2→O-phase transformation in Ti-Al-Nb alloys are explored bycomputer simulation using a phase-field method. The focus is on the influence of the applied strain direction onthe microstructure and volume fraction of the O-phase precipitates. It is found that altering applied strain directioncan modify microstructure of Ti-25Al-10～12Nb (at. pct) alloy during α_2→O-phase transformation effectively andfull laminate microstructure in the Ti-25Al-10Nb (at. pct) alloy can be realized by an applied strain only along thedirection 30°away from the α_2 phase <1010> in magnitude equivalent to the stress-free transformation strain. Thesimulation also shows that not only the magnitude of applied strain but also the applied strain direction influencesthe O-phase volume fraction and the effect of strain direction on the volume fraction is up to 25%.
基金the University of Scoence and Technology Beijing on the project 'Supersteel'.]
文摘The influence of deforming temperature on ferrite refinement was analyzed by comparing the microstructures obtained by deformation at above A(r3), in two-phase region of (alpha + gamma) and at below A(t) in clean 08 and 20Mn steels. The results indicate that ferrite refinement through strain induced transformation by deformation at above A(r3) is more effective than that by deformation simply through ferrite dynamic recrystallization. The main problem of ferrite refinement by deformation at below A(r3) is the inhomogeneity of microstructure which is controlled by the orientations and sizes of ferrite grains and the distribution of second phases. Ferrite dynamic recrystallization after strain induced transformation can further effectively refine ferrite.
文摘The effects of large strain and strain path reversal on the deformation microstructure evolution in austenite below the recrystallisation temperature were studied by hot torsion using a non-transforming Fe-30wt%Ni model austenitic alloy.Results show that the high angle boundaries (HABs) can be generated by both microstructure mechanism through dislocation accumulation and texture mechanism via subgrain rotation.However,multiple strain path reversals lead to less well-developed HABs in the original grains compared to single reversal deformed to the same amount of total accumulative strain.This effect is attributed to the subgrain rotation mechanism being less effective at small strains.In comparison,the same hot torsion tests were conducted using a microalloyed steel at a temperature between Ae 3 and Ar 3.After single strain path reversal,substantial deformation-induced austenite-to-ferrite phase transformation was observed.Meanwhile,a test with multiple strain path reversals but with the same total strain produces much lower levels of strain-induced ferrite formation.This difference is correlated to the observations made in the Fe-30wt%Ni model alloy.It is believed that the different amount of strain-induced ferrite originated from the different levels of strain-induced HABs within the austenite which act as ferrite nucleation sites.
基金This work was supported by the National Natural Science Foundation of China(Nos.52031011,91860109,51927801,and 51621063)the National Key Research and Development Program of China(Nos.2017YFB0702001 and 2016YFB0700404)+1 种基金111 Project 2.0 of China(No.BP2018008)funding from the Science and Technology Departments of Shaanxi and Xi’an,China(Nos.2016KTZDGY-04-03,2016KTZDGY-04-04,and 201805064ZD15CG48).
文摘Vanadium dioxide (VO_(2)) has emerged as a promising micro-actuator material for its large amplitude and high work density across the transition between the insulating (M_(1) and M_(2)) and metallic (R) phase. Even though M_(2)–R transition offers about 70% higher transformation stress than M_(1)–R structural phase transition, the application of the M_(2) phase in the micro-actuators is hindered by the fact that previously, M_(2) phase can only stay stable under tensile stress. In this work, we propose and verify that by synthesizing the VO_(2) nanowires under optimized oxygen-rich conditions, stoichiometry change can be introduced into the nanowires (NWs) which in turn yield a large number free-standing single-crystalline M_(2)-phase NWs stable at room temperature. In addition, we demonstrate that the output stress of the M_(2)-phase NWs is about 65% higher than that of the M_(1)-phase NWs during their transition to R phase, quite close to the theoretical prediction. Our findings open new avenues towards enhancing the performance of VO_(2)-based actuators by using M_(2)–R transition.
文摘Hot torsion testing was performed on a low carbon Nb-Ti microalloyed steel to study the effects of hot tor- sion parameters, strain and strain rate, on ultrafine ferrite grains production through dynamic strain-induced trans- formation, at a deformation temperature just above At3. The initiation and evolution of ultrafine ferrite grains were studied. The results show that the amount of strain and strain rate has conversely effect on the volume fraction and grain size of ultrafine ferrite grains. With increasing strain, the interior of austenite grains become activated as nucle- ation sites for fine ferrite grains. As a result, ferrite grains continuously nucleate not only at the former austenite grain boundaries but also inside the austenite grains which leads to a rapid increase in volume fraction of ultrafine grains. Increasing of strain rate reduces the tendency of ferrite grains coarsening so that ultrafine ferrite grains are achieved, while the volume fraction of ultrafine grains decreases at the same strain level.
