The high precision assemblies with considerable radial interference should be accompanied by heating and cooling processes.However,the mechanical properties of metals are greatly affected by thermal operations.So,for ...The high precision assemblies with considerable radial interference should be accompanied by heating and cooling processes.However,the mechanical properties of metals are greatly affected by thermal operations.So,for evaluating the stress distribution and distortion of teeth profiles in a gear/shaft assembly,a transient thermal analysis is necessary for finding the change in mechanical properties.The friction on the contact surface is another important parameter in interaction of the gear with the shaft.Evaluating the gear stress and deformation fields for several modes of heat transfer and friction coefficients showed that the maximum radial or tangential stresses on contact surface of the joint may have more than 8%increase by increasing friction coefficient;while the intensity of heat transfer at cooling stage has lower effect on stress distribution.展开更多
In order to examine if the heat conduction in porous material behaves like a wave as claimed by other researchers, experiments on transient heat transfer is conducted in casting sand. The results show that the heat pr...In order to examine if the heat conduction in porous material behaves like a wave as claimed by other researchers, experiments on transient heat transfer is conducted in casting sand. The results show that the heat propagation can be described neither by wave nor by diffusion model. The CV-wave concept is discussed and challenged according to the experimental results in the entire transient stage, including the transient response of temperature and the response curve of penetration-depth versus penetration-time.展开更多
We conducted a transient experimental investigation of steam–water direct contact condensation in the absence of noncondensible gas in a laboratory-scale column with the inner diameter of 325 mm and the height of 104...We conducted a transient experimental investigation of steam–water direct contact condensation in the absence of noncondensible gas in a laboratory-scale column with the inner diameter of 325 mm and the height of 1045 mm. We applied a new analysis method for the steam state equation to analyze the molar quantity change in steam over the course of the experiment and determined the transient steam variation. We also investigated the influence of flow rates and temperatures ofcooling water on the efficiency ofsteam condensation. Our experimental results show that appropriate increasing of the cooling water flow rate can significantly accelerate the steam condensation. We achieved a rapid increase in the total volumetric heat transfer coefficient by increasing the flow rate of cooling water, which indicated a higher thermal convection between the steam and the cooling water with higher flow rates. We found that the temperature ofcooling water did not play an important role on steam condensation. This method was confirmed to be effective for rapid recovering ofsteam.展开更多
Numerical studies on transient heat transfer characteristics of air-array-jet impingement with a small jet-to-plate distance and a large temperature difference between nozzles and plate were presented.The dimensionles...Numerical studies on transient heat transfer characteristics of air-array-jet impingement with a small jet-to-plate distance and a large temperature difference between nozzles and plate were presented.The dimensionless jet-to-plate distance(H/D)was 0.2,and non-dimensional nozzle-to-nozzle spacing(S/D)was 3,4,5 and 6,respectively.It is found that the quenching time is shortened at a constant total mass flow at air jet inlet m·(m·=218.21 kg/h),and the heat transfer uniformity is deterio-rated as S/D increases.However,the adding reversed-flow nozzles can shorten the quenching time of the glass plate considerably with a modest change in the heat transfer uniformity.The results at variable m·are the same as those at a fixed m·.Furthermore,the parity and arrangement of nozzles are also discussed,It is found that an odd number of nozzles is more beneficial for transient heat transfer.Based on these results,an appropriate proposal for ultra-thin glass tempering process is presented.展开更多
In dam works, air precooling of aggregate is a common and effective method to avoid temperature cracks in concrete structure. In order to offer a reliable design theory for the air precooling process to avoid unreason...In dam works, air precooling of aggregate is a common and effective method to avoid temperature cracks in concrete structure. In order to offer a reliable design theory for the air precooling process to avoid unreasonable energy consumption, the transient heat transfer characteristics of the aggregate are intensively analyzed. The combined structure of the aggregate and the interstitial space in the hopper is treated as a porous structure, and the space-average method is used to simulate the transient heat transfer process. Simulation results show that size of the hopper and the average air velocity in the cross section have great influence on the transient heat transfer process of the aggregate, while the porosity in the range of 0.4-0.5 has little influence. Nomograms are abstracted from simulation results, and then correlations of the compared excess temperature are precisely fitted to predict the air precooling transient heat transfer process of the aggregate.展开更多
The transient heat transfer between working fluid and inner wall of 600 MW supercritical pressureboiler's water separator model during start-up was experimentally explored. The test conditions forwater steam two-p...The transient heat transfer between working fluid and inner wall of 600 MW supercritical pressureboiler's water separator model during start-up was experimentally explored. The test conditions forwater steam two-phase were as follows: pressure P = 3 ~ 11 MPa, mass now M = 0.2 ~ 0.35 kg/s,and mass quality x = O.2 ~ 0.8; for subcooled water P = 3 ~ 11 MPa, M = 0.2 ~ 0.35 kg/s, andsubcooled degree △θ = 10℃. By using an accurate and tractable inverse heat conduction solution,the correlations of single phase and twouphase transient heat transfer coefficients were obtained. Theexperimental results demonstrated the heat transfer enhanced for subcooled water and water steammixture compared with fully developed turbulent flow in tube. The increasing heat transfer effect maybe attributed to the deformation or destruction f the boundary layer.展开更多
Miniaturization of electronic package leads to high heat density and heat accumulation in electronics device, resulting in short life time and premature failure of the device. Junction temperature and thermal resistan...Miniaturization of electronic package leads to high heat density and heat accumulation in electronics device, resulting in short life time and premature failure of the device. Junction temperature and thermal resistance are the critical parameters that determine the thermal management and reliability in electronics cooling. Metal oxide field effect transistor（MOSFET）is an important semiconductor device for light emitting diode-integrated circuit（LED IC） driver application, and thermal management in MOSFET is a major challenge. In this study, investigations on thermal performance of MOSFET are performed for evaluating the junction temperature and thermal resistance. Suitable modifications in FR4 substrates are proposed by introducing thermal vias and copper layer coating to improve the thermal performance of MOSFET. Experiments are conducted using thermal transient tester（T3ster） at 2.0 A input current and ambient temperature varying from25℃ to 75℃. The thermal parameters are measured for three proposed designs： FR4 with circular thermal vias, FR4 with single strip of copper layer and embedded vias, and FR4 with I-shaped copper layer, and compared with that of plain FR4 substrate. From the experimental results, FR4I-shaped shows promising results by 33.71% reduction in junction temperature and 54.19% reduction in thermal resistance. For elevated temperature, the relative increases in junction temperature and thermal resistance are lower for FR4I-shaped than those for other substrates considered. The introduction of thermal vias and copper layer plays a significant role in thermal performance.展开更多
Numerical results of three-dimensional separated flow and heat transfer in an enlarged rectangular channel are presented in this paper. The expansion ratio and aspect ratio of the channel are 2.0 and 8.0, respectively...Numerical results of three-dimensional separated flow and heat transfer in an enlarged rectangular channel are presented in this paper. The expansion ratio and aspect ratio of the channel are 2.0 and 8.0, respectively. Reynolds number of the flow is 200 and it is over the critical Reynolds number. Over the value, the flow in the symmetric channel becomes to deflect to one side of the walls. Transient response characteristics of the flow and heat transfer in the channel with the fully developed flow imposed one cycle of a pulsating fluctuation at the inlet are investigated. Vortex structure generated in the channel is visualized with a helicity isosurface. In the case of the fluctuation of Strouhal number 0.05, small streamwise vortices appear near the side walls and slightly upstream of the reattachment region of the short separation bubble. The vortices elongate and shed some vortices. These vortices attract some pairs of the streamwise vortices near the reattachment region quickly and they drift downstream along the side walls. They are inclined from the walls and are decaying gradually. It is clarified that high Nusselt number area appears and shifts downstream in accordance with the root of the vortices.展开更多
In the current work, transient heat conduction in a semi-infinite medium is considered for its many applications in various heat fields. Here, the homotopy analysis method （HAM） is applied to solve this problem and ...In the current work, transient heat conduction in a semi-infinite medium is considered for its many applications in various heat fields. Here, the homotopy analysis method （HAM） is applied to solve this problem and analytical results are compared with those of the exact and integral methods results. The results show that the HAM can give much better approximations than the other approximate methods： Changes in heat fluxes and profiles of temperature are obtained at different times and positions for copper, iron and aluminum.展开更多
According to heat transfer principle and the process of solving engineering problems by finite element method, examples were given to demonstrate how finite element analysis can be used to describe transient heat tran...According to heat transfer principle and the process of solving engineering problems by finite element method, examples were given to demonstrate how finite element analysis can be used to describe transient heat transfer through fabrics. Details were given to describe how conduction and convection affect temperature distribution and heat loss during heat transfer processes by taking advantage of the quick calculation of FEA software MSC.Marc. Experimental results show good agreement with the theoretical results.展开更多
This paper provides a numerical analysis model of unsteady heat trans-fer in piston-liner set of an internal combustion engine.The model simulates the un-steady heat transfer process among the combustion mixture,pisto...This paper provides a numerical analysis model of unsteady heat trans-fer in piston-liner set of an internal combustion engine.The model simulates the un-steady heat transfer process among the combustion mixture,piston set,lubricantfilm,liner and coolant in a whole engine cycle,and can predict the temperature fluc-tuation and distribution on piston crown,inner surface of liner,piston ring and thelubricant film.A computer program is developed to calculate the unsteady heat trans-fer process of piston-liner system in a water-cooled diesel engine.展开更多
An experimental system was set up to measure the temperature, pressure, heat transfer rate and mass flow rate in a semi-open two-phase thermosyphon. The behaviors of a semi-open two-phase thermosyphon during startup, ...An experimental system was set up to measure the temperature, pressure, heat transfer rate and mass flow rate in a semi-open two-phase thermosyphon. The behaviors of a semi-open two-phase thermosyphon during startup, shutdown and lack of water were studied to get complete understanding of its thermal characteristics. The variation of wall temperature, heat-exchange condition and pressure fluctuations of semi-open two-phase thermosyphons showed that the startup of SOTPT needs about 60-70 min; the startup speed of SOTPT is determined by the startup speed of the condensation section; the average pressure in the heat pipe is equal to the environmental pressure usually; the shutdown of SOTPT needs about 30-50min; a semi-open two-phase thermosyphon has good response to lack of water accident.展开更多
This work presented the development and validation of an analytical method to predict the transient temperature field in the asphalt pavement.The governing equation for heat transfer was based on heat conduction radia...This work presented the development and validation of an analytical method to predict the transient temperature field in the asphalt pavement.The governing equation for heat transfer was based on heat conduction radiation and convection.An innovative time-dependent function was proposed to predict the pavement surface temperature with solar radiation and air temperature using dimensional analysis in order to simplify the complex heat exchange on the pavement surface.The parameters for the time-dependent pavement surface temperature function were obtained through the regression analysis of field measurement data.Assuming that the initial pavement temperature distribution was linear and the influence of the base course materials on the temperature of the upper asphalt layers was negligible,a close-form analytical solution of the temperature in asphalt layers was derived using Green's function.Finally,two numerical examples were presented to validate the model solutions with field temperature measurements.Analysis results show that the solution accuracy is in agreement with field data and the relative errors at a shallower depth are greater than those at a deeper one.Although the model is not sensitive to dramatic changes in climatic factors near the pavement surface,it is applicable for predicting pavement temperature field in cloudless days.展开更多
文摘The high precision assemblies with considerable radial interference should be accompanied by heating and cooling processes.However,the mechanical properties of metals are greatly affected by thermal operations.So,for evaluating the stress distribution and distortion of teeth profiles in a gear/shaft assembly,a transient thermal analysis is necessary for finding the change in mechanical properties.The friction on the contact surface is another important parameter in interaction of the gear with the shaft.Evaluating the gear stress and deformation fields for several modes of heat transfer and friction coefficients showed that the maximum radial or tangential stresses on contact surface of the joint may have more than 8%increase by increasing friction coefficient;while the intensity of heat transfer at cooling stage has lower effect on stress distribution.
文摘In order to examine if the heat conduction in porous material behaves like a wave as claimed by other researchers, experiments on transient heat transfer is conducted in casting sand. The results show that the heat propagation can be described neither by wave nor by diffusion model. The CV-wave concept is discussed and challenged according to the experimental results in the entire transient stage, including the transient response of temperature and the response curve of penetration-depth versus penetration-time.
文摘We conducted a transient experimental investigation of steam–water direct contact condensation in the absence of noncondensible gas in a laboratory-scale column with the inner diameter of 325 mm and the height of 1045 mm. We applied a new analysis method for the steam state equation to analyze the molar quantity change in steam over the course of the experiment and determined the transient steam variation. We also investigated the influence of flow rates and temperatures ofcooling water on the efficiency ofsteam condensation. Our experimental results show that appropriate increasing of the cooling water flow rate can significantly accelerate the steam condensation. We achieved a rapid increase in the total volumetric heat transfer coefficient by increasing the flow rate of cooling water, which indicated a higher thermal convection between the steam and the cooling water with higher flow rates. We found that the temperature ofcooling water did not play an important role on steam condensation. This method was confirmed to be effective for rapid recovering ofsteam.
基金Natural Science Foundation of China(51335002,51905049)。
文摘Numerical studies on transient heat transfer characteristics of air-array-jet impingement with a small jet-to-plate distance and a large temperature difference between nozzles and plate were presented.The dimensionless jet-to-plate distance(H/D)was 0.2,and non-dimensional nozzle-to-nozzle spacing(S/D)was 3,4,5 and 6,respectively.It is found that the quenching time is shortened at a constant total mass flow at air jet inlet m·(m·=218.21 kg/h),and the heat transfer uniformity is deterio-rated as S/D increases.However,the adding reversed-flow nozzles can shorten the quenching time of the glass plate considerably with a modest change in the heat transfer uniformity.The results at variable m·are the same as those at a fixed m·.Furthermore,the parity and arrangement of nozzles are also discussed,It is found that an odd number of nozzles is more beneficial for transient heat transfer.Based on these results,an appropriate proposal for ultra-thin glass tempering process is presented.
基金financially supported by the Power Construction Corporation of China(GW-KJ-2011-14)
文摘In dam works, air precooling of aggregate is a common and effective method to avoid temperature cracks in concrete structure. In order to offer a reliable design theory for the air precooling process to avoid unreasonable energy consumption, the transient heat transfer characteristics of the aggregate are intensively analyzed. The combined structure of the aggregate and the interstitial space in the hopper is treated as a porous structure, and the space-average method is used to simulate the transient heat transfer process. Simulation results show that size of the hopper and the average air velocity in the cross section have great influence on the transient heat transfer process of the aggregate, while the porosity in the range of 0.4-0.5 has little influence. Nomograms are abstracted from simulation results, and then correlations of the compared excess temperature are precisely fitted to predict the air precooling transient heat transfer process of the aggregate.
文摘The transient heat transfer between working fluid and inner wall of 600 MW supercritical pressureboiler's water separator model during start-up was experimentally explored. The test conditions forwater steam two-phase were as follows: pressure P = 3 ~ 11 MPa, mass now M = 0.2 ~ 0.35 kg/s,and mass quality x = O.2 ~ 0.8; for subcooled water P = 3 ~ 11 MPa, M = 0.2 ~ 0.35 kg/s, andsubcooled degree △θ = 10℃. By using an accurate and tractable inverse heat conduction solution,the correlations of single phase and twouphase transient heat transfer coefficients were obtained. Theexperimental results demonstrated the heat transfer enhanced for subcooled water and water steammixture compared with fully developed turbulent flow in tube. The increasing heat transfer effect maybe attributed to the deformation or destruction f the boundary layer.
基金Project supported by the Collaborative Research in Engineering,Science&Technology(Grant No.P28C2-13)
文摘Miniaturization of electronic package leads to high heat density and heat accumulation in electronics device, resulting in short life time and premature failure of the device. Junction temperature and thermal resistance are the critical parameters that determine the thermal management and reliability in electronics cooling. Metal oxide field effect transistor（MOSFET）is an important semiconductor device for light emitting diode-integrated circuit（LED IC） driver application, and thermal management in MOSFET is a major challenge. In this study, investigations on thermal performance of MOSFET are performed for evaluating the junction temperature and thermal resistance. Suitable modifications in FR4 substrates are proposed by introducing thermal vias and copper layer coating to improve the thermal performance of MOSFET. Experiments are conducted using thermal transient tester（T3ster） at 2.0 A input current and ambient temperature varying from25℃ to 75℃. The thermal parameters are measured for three proposed designs： FR4 with circular thermal vias, FR4 with single strip of copper layer and embedded vias, and FR4 with I-shaped copper layer, and compared with that of plain FR4 substrate. From the experimental results, FR4I-shaped shows promising results by 33.71% reduction in junction temperature and 54.19% reduction in thermal resistance. For elevated temperature, the relative increases in junction temperature and thermal resistance are lower for FR4I-shaped than those for other substrates considered. The introduction of thermal vias and copper layer plays a significant role in thermal performance.
文摘Numerical results of three-dimensional separated flow and heat transfer in an enlarged rectangular channel are presented in this paper. The expansion ratio and aspect ratio of the channel are 2.0 and 8.0, respectively. Reynolds number of the flow is 200 and it is over the critical Reynolds number. Over the value, the flow in the symmetric channel becomes to deflect to one side of the walls. Transient response characteristics of the flow and heat transfer in the channel with the fully developed flow imposed one cycle of a pulsating fluctuation at the inlet are investigated. Vortex structure generated in the channel is visualized with a helicity isosurface. In the case of the fluctuation of Strouhal number 0.05, small streamwise vortices appear near the side walls and slightly upstream of the reattachment region of the short separation bubble. The vortices elongate and shed some vortices. These vortices attract some pairs of the streamwise vortices near the reattachment region quickly and they drift downstream along the side walls. They are inclined from the walls and are decaying gradually. It is clarified that high Nusselt number area appears and shifts downstream in accordance with the root of the vortices.
文摘In the current work, transient heat conduction in a semi-infinite medium is considered for its many applications in various heat fields. Here, the homotopy analysis method （HAM） is applied to solve this problem and analytical results are compared with those of the exact and integral methods results. The results show that the HAM can give much better approximations than the other approximate methods： Changes in heat fluxes and profiles of temperature are obtained at different times and positions for copper, iron and aluminum.
文摘According to heat transfer principle and the process of solving engineering problems by finite element method, examples were given to demonstrate how finite element analysis can be used to describe transient heat transfer through fabrics. Details were given to describe how conduction and convection affect temperature distribution and heat loss during heat transfer processes by taking advantage of the quick calculation of FEA software MSC.Marc. Experimental results show good agreement with the theoretical results.
文摘This paper provides a numerical analysis model of unsteady heat trans-fer in piston-liner set of an internal combustion engine.The model simulates the un-steady heat transfer process among the combustion mixture,piston set,lubricantfilm,liner and coolant in a whole engine cycle,and can predict the temperature fluc-tuation and distribution on piston crown,inner surface of liner,piston ring and thelubricant film.A computer program is developed to calculate the unsteady heat trans-fer process of piston-liner system in a water-cooled diesel engine.
文摘An experimental system was set up to measure the temperature, pressure, heat transfer rate and mass flow rate in a semi-open two-phase thermosyphon. The behaviors of a semi-open two-phase thermosyphon during startup, shutdown and lack of water were studied to get complete understanding of its thermal characteristics. The variation of wall temperature, heat-exchange condition and pressure fluctuations of semi-open two-phase thermosyphons showed that the startup of SOTPT needs about 60-70 min; the startup speed of SOTPT is determined by the startup speed of the condensation section; the average pressure in the heat pipe is equal to the environmental pressure usually; the shutdown of SOTPT needs about 30-50min; a semi-open two-phase thermosyphon has good response to lack of water accident.
基金Project(2012zzts019)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(201306370121)supported by State Scholarship Fund of ChinaProject(51248006)supported by the National Natural Science Foundation,China
文摘This work presented the development and validation of an analytical method to predict the transient temperature field in the asphalt pavement.The governing equation for heat transfer was based on heat conduction radiation and convection.An innovative time-dependent function was proposed to predict the pavement surface temperature with solar radiation and air temperature using dimensional analysis in order to simplify the complex heat exchange on the pavement surface.The parameters for the time-dependent pavement surface temperature function were obtained through the regression analysis of field measurement data.Assuming that the initial pavement temperature distribution was linear and the influence of the base course materials on the temperature of the upper asphalt layers was negligible,a close-form analytical solution of the temperature in asphalt layers was derived using Green's function.Finally,two numerical examples were presented to validate the model solutions with field temperature measurements.Analysis results show that the solution accuracy is in agreement with field data and the relative errors at a shallower depth are greater than those at a deeper one.Although the model is not sensitive to dramatic changes in climatic factors near the pavement surface,it is applicable for predicting pavement temperature field in cloudless days.
