A novel hollow star-shaped chiral metamaterial(SCM)is proposed by incorporating chiral structural properties into the standard hollow star-shaped metamaterial,exhibiting a wide band gap over 1500 Hz.To broaden the ban...A novel hollow star-shaped chiral metamaterial(SCM)is proposed by incorporating chiral structural properties into the standard hollow star-shaped metamaterial,exhibiting a wide band gap over 1500 Hz.To broaden the band gap,solid single-phase and two-phase SCMs are designed and simulated,which produce two ultra-wide band gaps(approximately 5116 Hz and 6027 Hz,respectively).The main reason for the formation of the ultra-wide band gap is that the rotational vibration of the concave star of two novel SCMs drains the energy of an elastic wave.The impacts of the concave angle of a single-phase SCM and the resonator radius of a two-phase SCM on the band gaps are studied.Decreasing the concave angle leads to an increase in the width of the widest band gap,and the width of the widest band gap increases as the resonator radius of the two-phase SCM increases.Additionally,the study on elastic wave propagation characteristics involves analyzing frequency dispersion surfaces,wave propagation directions,group velocities,and phase velocities.Ultimately,the analysis focuses on the transmission properties of finite periodic structures.The solid single-phase SCM achieves a maximum vibration attenuation over 800,while the width of the band gap is smaller than that of the two-phase SCM.Both metamaterials exhibit high vibration attenuation capabilities,which can be used in wideband vibration reduction to satisfy the requirement of ultra-wide frequencies.展开更多
The Peak to Average power Ratio (PAR) of a Multi-Band Orthogonal Frequency-Division Multiplexing (MB-OFDM) Ultra-Wide Band (UWB) signals can be substantially larger than that of single carrier or carrier-less ultra-wi...The Peak to Average power Ratio (PAR) of a Multi-Band Orthogonal Frequency-Division Multiplexing (MB-OFDM) Ultra-Wide Band (UWB) signals can be substantially larger than that of single carrier or carrier-less ultra-wideband signals. In this letter, a novel PAR reduction scheme for the MB-OFDM UWB system based on spreading and interleaving is proposed. By spreading the coded bits over each subcarrier in corresponding band and interleaving the spread symbols across all bands, the PAR statistics of the MB-OFDM signals can be improved and the PAR is reduced obviously. In the PAR reduction scheme, there is no loss in transmission data rate or Bit Error Rate (BER) performance decreasing. Since the spreading and interleaving operation are implemented by unitary Hadamard sequences and used for an approach to provide the robustness of the UWB system to narrowband interference, there is no additional implementation burden. Simulation results show that the investigated scheme gives the PAR reduction of 3dB compared with that of the original MB-OFDM signals.展开更多
This paper analyzes mathematically the crucial aspects of signal processing in a Multi-Band (MB) Orthogonal Frequency Division Multiplexing (OFDM) based system considering Ultra-Wideband (UWB) channel environment. In ...This paper analyzes mathematically the crucial aspects of signal processing in a Multi-Band (MB) Orthogonal Frequency Division Multiplexing (OFDM) based system considering Ultra-Wideband (UWB) channel environment. In the process of analysis, it emphasizes the significant features of UWB receiver design in comparison with ‘conventional’ narrow-band system. The analysis shows that the high dispersive nature of a frequency selective UWB channel effects the design of different signal processing blocks like pre-select filter, low noise amplifier (LNA) and analog-to-digital (A/D) converter in the receiver front end. The characteristic functions of each of these stages are now dominated by the channel characteristics and it needs to be modified accordingly. This analysis is extended further with the study of frequency offset error and its correction. The unbiased Cramer Rao Lower Bound (CRLB) of estimation error is calculated and supported by computer simulation. The performance of an MB-OFDM system with frequency offset correction in terms of Bit-Error-Rate (BER) is also reported.展开更多
The evaluation of System Performance of UWB (ultra-wide band) jointing in MC (multi-carrier) signaling in correlated environments is presented in the report. The correlated Nakagami-m statistical distribution for the ...The evaluation of System Performance of UWB (ultra-wide band) jointing in MC (multi-carrier) signaling in correlated environments is presented in the report. The correlated Nakagami-m statistical distribution for the multipath fading model is assumed in this scenario. In fact to establish the model for analyzing in this article is using MC-CDMA (multi-carrier code-division multiple-access) system characterization combined with a UWB scheme. The average BER (bit error rate) is calculated and compared to a special case of previously published results. Studied results from this paper can be implied to approve the system performance for a UWB system combined with a MC-CDMA wireless communication system. It is worth noting that the Nakagami-m distributed fading parameter significantly dominates UWB system performance when it cooperates with MC signaling under a fading environment. Finally, it is worthy of noting that when the SNR (signal-to-noise ratio) at system’s receiver reaches a preset high threshold value, the parameter of power decay ratio effect could be not included.展开更多
In this paper, a compact coplanar epsilon.negative(ENG) antenna is proposed with ultra.wide operation band and small size of 18×11.5 mm2. The proposed antenna is designed based on a coplanar.waveguide(CPW) feedin...In this paper, a compact coplanar epsilon.negative(ENG) antenna is proposed with ultra.wide operation band and small size of 18×11.5 mm2. The proposed antenna is designed based on a coplanar.waveguide(CPW) feeding antenna, and thus the via.free structure is employed to realize the ENG unit cell, which is convenient to tune the frequency of zeroth.order resonance(ZOR) and extends the ZOR bandwidth. The high.order resonant frequencies are achieved and mainly determined by the separate slots that are located between the radiating patch and the ground plane. Adding the left.handed inductance between the radiating patch and ground has slight impact on the high.order resonant frequencies, and then the ultra.wide band is achieved by merging the ZOR bandwidth with the high.order resonant bandwidths. The ground plane primarily works as a matching network for the proposed antenna. Although it generates a low.frequency resonance, the performance is undesirable due to the impedance mismatching. The measured results show that the reflection coefficient, |S11| <.10 d B, is in a wide frequency range from 5.25 to 13 GHz, which covers the upper operation band of UWB communication. Also, the antenna contains relatively stable gains and omni.directional radiation patterns.展开更多
The modern landmine＇s electronic fuse is susceptible to strong interference or can even be damaged by the ultra-wide band electromagnetic pulse（UWB-EMP）. The finite-difference time-domain（FDTD） method in lossy me...The modern landmine＇s electronic fuse is susceptible to strong interference or can even be damaged by the ultra-wide band electromagnetic pulse（UWB-EMP）. The finite-difference time-domain（FDTD） method in lossy media with cylindrical coordinates is used to study the interactions of the UWB-EMP with the landmine. First, the coupling of UWB-EMP into the landmine shielding shell through an aperture is numerically simulated. Second, the coupled electromagnetic field of mine shells made of different shielding materials and with apertures of different sizes is plotted. Third, the aperture coupling laws of UWB-EMP into shells are analyzed and categorized. Such an algorithm is capable of effectively preventing ladder similar errors, and consequently improving the calculation precision, and in addition to adopting the message passing interface（MPI） parallel method to divide the total calculating range into more sub-ranges, the overall calculating efficiency is greatly increased. These calculations are surely a constructive reference for modern landmine design against electromagnetic damage.展开更多
To solve the precision self-positioning problem for mobile robot,a positioning program based on ultra-wideband technology was proposed. Ultra-wideband pulse has very high bandwidth; ranging accuracy can achieve centim...To solve the precision self-positioning problem for mobile robot,a positioning program based on ultra-wideband technology was proposed. Ultra-wideband pulse has very high bandwidth; ranging accuracy can achieve centimeter-level theoretically. The mobile robot obtained the distance to the reference node by sending ultra-wideband pulse. According to the geometric relations among the references and the robot,establish equations to calculate the position coordinates. Then Kalman filter algorithm was applied for mobile robot tracking. Simulation results show that robot positioning and tracking based on ultra-wideband technology can achieve indoor and outdoor seamless docking.展开更多
Theoretical calculations predict transition frequencies in the terahertz range for the field-effect transistors based on carbon nanotubes, and this shows their suitability for being used in high frequency applications...Theoretical calculations predict transition frequencies in the terahertz range for the field-effect transistors based on carbon nanotubes, and this shows their suitability for being used in high frequency applications. In this paper, we have designed a field-effect transistor based on carbon nanotube with high transition frequency suitable for ultra-wide band applications. We did this by optimizing nanotube diameter, gate insulator thickness and dielectric constant. As a result, we achieved the transition frequency about 7.45 THz. The environment of open source software FETToy is used to simulate the device. Also a suitable model for calculating the transition frequency is presented.展开更多
With reference to the air target detection of ultra-wide band (UWB)/impulse radar(IR), the transient signal processing techniques was discussed. In weak UWB signal detection, the wavelet transforms and high order spec...With reference to the air target detection of ultra-wide band (UWB)/impulse radar(IR), the transient signal processing techniques was discussed. In weak UWB signal detection, the wavelet transforms and high order spectrum estimation techniques were preferred. In target characteristic analysis, a time domain bispectrum estimation algorithm was used to analyze the target impulse response, which could estimate accurately local scattering distribution of complex target. A free field IR experimental system installed in an anechoic chamber was used. With this system, experiments to several target models were made. The results of these experiments verified the signal processing method efficiency.展开更多
This analysis focuses on PIM interference under multi-band multi-signal input in mobile communication system.Unlike single band system that only odd order PIM(especially 3rd order) should be concerned,in multi-band mu...This analysis focuses on PIM interference under multi-band multi-signal input in mobile communication system.Unlike single band system that only odd order PIM(especially 3rd order) should be concerned,in multi-band multi-signal case,both odd and even order PIM could be interference source because of more complicated intermodulation,more IMPs generated and more receive bands.Especially,the 2nd order PIM may interfere more serious to receiving channel for its strong magnitude.In duplex indoor distribute system,the PIM interference is a potential problem to GSM900,DCS1800,CDMA,and even 3G system wireless services,because the PIM frequencies may fall in receive bands and interfere to the receiving channels.In radio system design and wireless channel assignment,precautions must be taken to minimize the PIM level and to avoid interfere to receiving channels.For practical use,the lower order possible PIM interference to 2G and 3G systems is calculated.展开更多
Using an improved particle swarm optimization algorithm(IPSO)to drive a transfer matrix method,a nonreciprocal absorber with an ultrawide absorption bandwidth and angular insensitivity is realized in plasma-embedded p...Using an improved particle swarm optimization algorithm(IPSO)to drive a transfer matrix method,a nonreciprocal absorber with an ultrawide absorption bandwidth and angular insensitivity is realized in plasma-embedded photonic crystals arranged in a structure composed of periodic and quasi-periodic sequences on a normalized scale.The effective dielectric function,which determines the absorption of the plasma,is subject to the basic parameters of the plasma,causing the absorption of the proposed absorber to be easily modulated by these parameters.Compared with other quasi-periodic sequences,the Octonacci sequence is superior both in relative bandwidth and absolute bandwidth.Under further optimization using IPSO with 14 parameters set to be optimized,the absorption characteristics of the proposed structure with different numbers of layers of the smallest structure unit N are shown and discussed.IPSO is also used to address angular insensitive nonreciprocal ultrawide bandwidth absorption,and the optimized result shows excellent unidirectional absorbability and angular insensitivity of the proposed structure.The impacts of the sequence number of quasi-periodic sequence M and collision frequency of plasma1ν1 to absorption in the angle domain and frequency domain are investigated.Additionally,the impedance match theory and the interference field theory are introduced to express the findings of the algorithm.展开更多
随着物联网技术的飞速发展,窄带物联网(Narrow Band Internet of Things,NB-IoT)作为一种低功耗、广覆盖、大连接的无线通信技术,逐渐成为连接物理世界与数字世界的桥梁。然而,在实际应用中,NB-IoT信号面临着诸如信号衰减、干扰、覆盖...随着物联网技术的飞速发展,窄带物联网(Narrow Band Internet of Things,NB-IoT)作为一种低功耗、广覆盖、大连接的无线通信技术,逐渐成为连接物理世界与数字世界的桥梁。然而,在实际应用中,NB-IoT信号面临着诸如信号衰减、干扰、覆盖不均等挑战。这些挑战不仅影响用户体验,还限制了物联网应用的进一步发展。因此,研究面向物联网的NB-IoT信号优化方法具有重要意义。文章深入研究面向物联网的NB-IoT信号优化方法,提出多种有效的优化策略和技术手段。展开更多
针对太赫兹频段高速移动场景,提出了一种参考信号方案——增强型离散傅里叶变换扩展正交频分复用(E DFT-s-OFDM)DMRS:将具有循环前缀(CP)和循环后缀(CS)的参考信号序列分割为首部和尾部参考信号序列,然后分别嵌入每个OFDM符号的尾部和...针对太赫兹频段高速移动场景,提出了一种参考信号方案——增强型离散傅里叶变换扩展正交频分复用(E DFT-s-OFDM)DMRS:将具有循环前缀(CP)和循环后缀(CS)的参考信号序列分割为首部和尾部参考信号序列,然后分别嵌入每个OFDM符号的尾部和首部。这种方案的优点在于,前一个OFDM符号的尾部和后一个OFDM符号的首部构成一个完整的参考信号序列,从而允许接收端在每个OFDM符号间隔内都能进行信道估计,提高了信道估计的精度和实时性。此外,相邻OFDM符号的首部和尾部参考信号序列相同,从而省去了每个OFDM符号的传统循环前缀(CP),提高了频谱效率。仿真结果表明,在太赫兹频段高速移动场景下,与5G NR DFT-s-OFDM波形的DMRS方案相比,该方案的信道估计更精确,通信系统的频谱效率更高。展开更多
目的:分析脑干带状高信号的软脑膜转移病例的临床特征。方法:收集海南医学院第一附属医院及检索知网、万方、维普、PubMed、Web of Science等数据库中报道磁共振表现为脑干带状高信号的患者,收集并整理纳入患者的既往病史、症状、体征...目的:分析脑干带状高信号的软脑膜转移病例的临床特征。方法:收集海南医学院第一附属医院及检索知网、万方、维普、PubMed、Web of Science等数据库中报道磁共振表现为脑干带状高信号的患者,收集并整理纳入患者的既往病史、症状、体征、基因检查结果、脑脊液表现、治疗及预后等。结果:共纳入28例患者,其中26例有肺腺癌病史,2例发现肺部占位性改变,磁共振均表现为T2‐FLAIR上脑干腹侧呈带状高信号,两侧对称,可延伸至小脑脚,DWI呈高信号,ADC呈低信号,T1加权成像为长T1信号,T2加权成像为长T2信号,增强扫描未见强化。结论:识别肺癌继发软脑膜转移很重要,T2‐FLAIR和DWI上脑干无强化带状高信号很可能是非小细胞肺癌继发软脑膜转移的特征性表现。展开更多
基金supported by the National Natural Science Foundation of China(Nos.12372019,12072222,12132010,12021002,and 11991032)the Open Projects of State Key Laboratory for Strength and Structural Integrity of China(No.ASSIKFJJ202303002)+1 种基金the State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures of China(No.SKLTESKF1901)the Aeronautical Science Foundation of China(No.ASFC-201915048001)。
文摘A novel hollow star-shaped chiral metamaterial(SCM)is proposed by incorporating chiral structural properties into the standard hollow star-shaped metamaterial,exhibiting a wide band gap over 1500 Hz.To broaden the band gap,solid single-phase and two-phase SCMs are designed and simulated,which produce two ultra-wide band gaps(approximately 5116 Hz and 6027 Hz,respectively).The main reason for the formation of the ultra-wide band gap is that the rotational vibration of the concave star of two novel SCMs drains the energy of an elastic wave.The impacts of the concave angle of a single-phase SCM and the resonator radius of a two-phase SCM on the band gaps are studied.Decreasing the concave angle leads to an increase in the width of the widest band gap,and the width of the widest band gap increases as the resonator radius of the two-phase SCM increases.Additionally,the study on elastic wave propagation characteristics involves analyzing frequency dispersion surfaces,wave propagation directions,group velocities,and phase velocities.Ultimately,the analysis focuses on the transmission properties of finite periodic structures.The solid single-phase SCM achieves a maximum vibration attenuation over 800,while the width of the band gap is smaller than that of the two-phase SCM.Both metamaterials exhibit high vibration attenuation capabilities,which can be used in wideband vibration reduction to satisfy the requirement of ultra-wide frequencies.
基金Supported by the National 863 High Technology Research Program of China (N0.2005AA123320)Universities Natural Science Research Project of Jiangsu Province (No.05KJB510101).
文摘The Peak to Average power Ratio (PAR) of a Multi-Band Orthogonal Frequency-Division Multiplexing (MB-OFDM) Ultra-Wide Band (UWB) signals can be substantially larger than that of single carrier or carrier-less ultra-wideband signals. In this letter, a novel PAR reduction scheme for the MB-OFDM UWB system based on spreading and interleaving is proposed. By spreading the coded bits over each subcarrier in corresponding band and interleaving the spread symbols across all bands, the PAR statistics of the MB-OFDM signals can be improved and the PAR is reduced obviously. In the PAR reduction scheme, there is no loss in transmission data rate or Bit Error Rate (BER) performance decreasing. Since the spreading and interleaving operation are implemented by unitary Hadamard sequences and used for an approach to provide the robustness of the UWB system to narrowband interference, there is no additional implementation burden. Simulation results show that the investigated scheme gives the PAR reduction of 3dB compared with that of the original MB-OFDM signals.
文摘This paper analyzes mathematically the crucial aspects of signal processing in a Multi-Band (MB) Orthogonal Frequency Division Multiplexing (OFDM) based system considering Ultra-Wideband (UWB) channel environment. In the process of analysis, it emphasizes the significant features of UWB receiver design in comparison with ‘conventional’ narrow-band system. The analysis shows that the high dispersive nature of a frequency selective UWB channel effects the design of different signal processing blocks like pre-select filter, low noise amplifier (LNA) and analog-to-digital (A/D) converter in the receiver front end. The characteristic functions of each of these stages are now dominated by the channel characteristics and it needs to be modified accordingly. This analysis is extended further with the study of frequency offset error and its correction. The unbiased Cramer Rao Lower Bound (CRLB) of estimation error is calculated and supported by computer simulation. The performance of an MB-OFDM system with frequency offset correction in terms of Bit-Error-Rate (BER) is also reported.
文摘The evaluation of System Performance of UWB (ultra-wide band) jointing in MC (multi-carrier) signaling in correlated environments is presented in the report. The correlated Nakagami-m statistical distribution for the multipath fading model is assumed in this scenario. In fact to establish the model for analyzing in this article is using MC-CDMA (multi-carrier code-division multiple-access) system characterization combined with a UWB scheme. The average BER (bit error rate) is calculated and compared to a special case of previously published results. Studied results from this paper can be implied to approve the system performance for a UWB system combined with a MC-CDMA wireless communication system. It is worth noting that the Nakagami-m distributed fading parameter significantly dominates UWB system performance when it cooperates with MC signaling under a fading environment. Finally, it is worthy of noting that when the SNR (signal-to-noise ratio) at system’s receiver reaches a preset high threshold value, the parameter of power decay ratio effect could be not included.
基金supported by the National Natural Science Foundation of China (NNSF) under Grant 61531016National Natural Science Foundation of China (NNSF) under Grant 61271090+1 种基金Sichuan province science and technology support project under Grant 2016GZ0059Sichuan province science and technology support project under Grant 2017GZ0110
文摘In this paper, a compact coplanar epsilon.negative(ENG) antenna is proposed with ultra.wide operation band and small size of 18×11.5 mm2. The proposed antenna is designed based on a coplanar.waveguide(CPW) feeding antenna, and thus the via.free structure is employed to realize the ENG unit cell, which is convenient to tune the frequency of zeroth.order resonance(ZOR) and extends the ZOR bandwidth. The high.order resonant frequencies are achieved and mainly determined by the separate slots that are located between the radiating patch and the ground plane. Adding the left.handed inductance between the radiating patch and ground has slight impact on the high.order resonant frequencies, and then the ultra.wide band is achieved by merging the ZOR bandwidth with the high.order resonant bandwidths. The ground plane primarily works as a matching network for the proposed antenna. Although it generates a low.frequency resonance, the performance is undesirable due to the impedance mismatching. The measured results show that the reflection coefficient, |S11| <.10 d B, is in a wide frequency range from 5.25 to 13 GHz, which covers the upper operation band of UWB communication. Also, the antenna contains relatively stable gains and omni.directional radiation patterns.
基金Project supported by the Postdoctoral Science Foundation of China(Grant No.2014M552610)
文摘The modern landmine＇s electronic fuse is susceptible to strong interference or can even be damaged by the ultra-wide band electromagnetic pulse（UWB-EMP）. The finite-difference time-domain（FDTD） method in lossy media with cylindrical coordinates is used to study the interactions of the UWB-EMP with the landmine. First, the coupling of UWB-EMP into the landmine shielding shell through an aperture is numerically simulated. Second, the coupled electromagnetic field of mine shells made of different shielding materials and with apertures of different sizes is plotted. Third, the aperture coupling laws of UWB-EMP into shells are analyzed and categorized. Such an algorithm is capable of effectively preventing ladder similar errors, and consequently improving the calculation precision, and in addition to adopting the message passing interface（MPI） parallel method to divide the total calculating range into more sub-ranges, the overall calculating efficiency is greatly increased. These calculations are surely a constructive reference for modern landmine design against electromagnetic damage.
基金High Technology Research and Development Program(863program) of China (No.2007AA041604)
文摘To solve the precision self-positioning problem for mobile robot,a positioning program based on ultra-wideband technology was proposed. Ultra-wideband pulse has very high bandwidth; ranging accuracy can achieve centimeter-level theoretically. The mobile robot obtained the distance to the reference node by sending ultra-wideband pulse. According to the geometric relations among the references and the robot,establish equations to calculate the position coordinates. Then Kalman filter algorithm was applied for mobile robot tracking. Simulation results show that robot positioning and tracking based on ultra-wideband technology can achieve indoor and outdoor seamless docking.
文摘Theoretical calculations predict transition frequencies in the terahertz range for the field-effect transistors based on carbon nanotubes, and this shows their suitability for being used in high frequency applications. In this paper, we have designed a field-effect transistor based on carbon nanotube with high transition frequency suitable for ultra-wide band applications. We did this by optimizing nanotube diameter, gate insulator thickness and dielectric constant. As a result, we achieved the transition frequency about 7.45 THz. The environment of open source software FETToy is used to simulate the device. Also a suitable model for calculating the transition frequency is presented.
文摘With reference to the air target detection of ultra-wide band (UWB)/impulse radar(IR), the transient signal processing techniques was discussed. In weak UWB signal detection, the wavelet transforms and high order spectrum estimation techniques were preferred. In target characteristic analysis, a time domain bispectrum estimation algorithm was used to analyze the target impulse response, which could estimate accurately local scattering distribution of complex target. A free field IR experimental system installed in an anechoic chamber was used. With this system, experiments to several target models were made. The results of these experiments verified the signal processing method efficiency.
文摘This analysis focuses on PIM interference under multi-band multi-signal input in mobile communication system.Unlike single band system that only odd order PIM(especially 3rd order) should be concerned,in multi-band multi-signal case,both odd and even order PIM could be interference source because of more complicated intermodulation,more IMPs generated and more receive bands.Especially,the 2nd order PIM may interfere more serious to receiving channel for its strong magnitude.In duplex indoor distribute system,the PIM interference is a potential problem to GSM900,DCS1800,CDMA,and even 3G system wireless services,because the PIM frequencies may fall in receive bands and interfere to the receiving channels.In radio system design and wireless channel assignment,precautions must be taken to minimize the PIM level and to avoid interfere to receiving channels.For practical use,the lower order possible PIM interference to 2G and 3G systems is calculated.
文摘Using an improved particle swarm optimization algorithm(IPSO)to drive a transfer matrix method,a nonreciprocal absorber with an ultrawide absorption bandwidth and angular insensitivity is realized in plasma-embedded photonic crystals arranged in a structure composed of periodic and quasi-periodic sequences on a normalized scale.The effective dielectric function,which determines the absorption of the plasma,is subject to the basic parameters of the plasma,causing the absorption of the proposed absorber to be easily modulated by these parameters.Compared with other quasi-periodic sequences,the Octonacci sequence is superior both in relative bandwidth and absolute bandwidth.Under further optimization using IPSO with 14 parameters set to be optimized,the absorption characteristics of the proposed structure with different numbers of layers of the smallest structure unit N are shown and discussed.IPSO is also used to address angular insensitive nonreciprocal ultrawide bandwidth absorption,and the optimized result shows excellent unidirectional absorbability and angular insensitivity of the proposed structure.The impacts of the sequence number of quasi-periodic sequence M and collision frequency of plasma1ν1 to absorption in the angle domain and frequency domain are investigated.Additionally,the impedance match theory and the interference field theory are introduced to express the findings of the algorithm.
文摘随着物联网技术的飞速发展,窄带物联网(Narrow Band Internet of Things,NB-IoT)作为一种低功耗、广覆盖、大连接的无线通信技术,逐渐成为连接物理世界与数字世界的桥梁。然而,在实际应用中,NB-IoT信号面临着诸如信号衰减、干扰、覆盖不均等挑战。这些挑战不仅影响用户体验,还限制了物联网应用的进一步发展。因此,研究面向物联网的NB-IoT信号优化方法具有重要意义。文章深入研究面向物联网的NB-IoT信号优化方法,提出多种有效的优化策略和技术手段。
文摘针对太赫兹频段高速移动场景,提出了一种参考信号方案——增强型离散傅里叶变换扩展正交频分复用(E DFT-s-OFDM)DMRS:将具有循环前缀(CP)和循环后缀(CS)的参考信号序列分割为首部和尾部参考信号序列,然后分别嵌入每个OFDM符号的尾部和首部。这种方案的优点在于,前一个OFDM符号的尾部和后一个OFDM符号的首部构成一个完整的参考信号序列,从而允许接收端在每个OFDM符号间隔内都能进行信道估计,提高了信道估计的精度和实时性。此外,相邻OFDM符号的首部和尾部参考信号序列相同,从而省去了每个OFDM符号的传统循环前缀(CP),提高了频谱效率。仿真结果表明,在太赫兹频段高速移动场景下,与5G NR DFT-s-OFDM波形的DMRS方案相比,该方案的信道估计更精确,通信系统的频谱效率更高。
文摘目的:分析脑干带状高信号的软脑膜转移病例的临床特征。方法:收集海南医学院第一附属医院及检索知网、万方、维普、PubMed、Web of Science等数据库中报道磁共振表现为脑干带状高信号的患者,收集并整理纳入患者的既往病史、症状、体征、基因检查结果、脑脊液表现、治疗及预后等。结果:共纳入28例患者,其中26例有肺腺癌病史,2例发现肺部占位性改变,磁共振均表现为T2‐FLAIR上脑干腹侧呈带状高信号,两侧对称,可延伸至小脑脚,DWI呈高信号,ADC呈低信号,T1加权成像为长T1信号,T2加权成像为长T2信号,增强扫描未见强化。结论:识别肺癌继发软脑膜转移很重要,T2‐FLAIR和DWI上脑干无强化带状高信号很可能是非小细胞肺癌继发软脑膜转移的特征性表现。
