A general procedure to capture the 'dynanmic Stiffness' is presented in this paper. The governing equations of motion are formulated for an arbitrary flexible body in large overall motion based on Kane's ...A general procedure to capture the 'dynanmic Stiffness' is presented in this paper. The governing equations of motion are formulated for an arbitrary flexible body in large overall motion based on Kane's equations . The linearization is performed peroperly by means of geometrically nonlinear straindisplacement relations and the nonlinear expression of angular velocity so that the 'dynamical stiffness' terms can be captured naturally in a general tcase. The concept and formulations of partial velocity and angular velocity arrays of Huston's method are extended to the flexible body and form the basis of the analysis. The validity and generality of the procedure presented in the paper are verified by numerical results of its application in both the beam and plate models.展开更多
As one of the most important steps in the design of bearing-less rotor systems,the design of flexible beam has received much research attention.Because of the very complex working environment of helicopter,the flexibl...As one of the most important steps in the design of bearing-less rotor systems,the design of flexible beam has received much research attention.Because of the very complex working environment of helicopter,the flexible beam should satisfy both the strength and dynamic requirements.However,traditional optimization research focused only on either the strength or dynamical characteristics.To sufficiently improve the performance of the flexible beam,both aspects must be considered.This paper proposes a two-stage optimization method based on the Hamilton variational principle:Variational asymptotic beam section analysis(VABS)program and genetic algorithm(GA).Consequently,a two-part analysis model based on the Hamilton variational principle and VABS is established to calculate section characteristics and structural dynamics characteristics,respectively.Subsequently,the two parts are combined to establish a two-stage optimization process and search with GA to obtain the best dynamic characteristics combinations.Based on the primary optimization results,the section characteristics of the flexible beam are further optimized using GA.The optimization results show that the torsional stiffness decreases by 36.1%compared with the full 0°laying scheme without optimization and the dynamic requirements are achieved.The natural frequencies of flapping and torsion meet the requirements(0.5 away from the passing frequencies of the blade,0.25 away from the excitation force frequency,and the flapping and torsion frequencies keep a corresponding distance).The results indicate that the optimization method can significantly improve the performance of the flexible beam.展开更多
文摘A general procedure to capture the 'dynanmic Stiffness' is presented in this paper. The governing equations of motion are formulated for an arbitrary flexible body in large overall motion based on Kane's equations . The linearization is performed peroperly by means of geometrically nonlinear straindisplacement relations and the nonlinear expression of angular velocity so that the 'dynamical stiffness' terms can be captured naturally in a general tcase. The concept and formulations of partial velocity and angular velocity arrays of Huston's method are extended to the flexible body and form the basis of the analysis. The validity and generality of the procedure presented in the paper are verified by numerical results of its application in both the beam and plate models.
基金supported by the Foundation of National Key Laboratory of Rotorcraft Aeromechanics,Nanjing University of Aeronautics and Astronautics(No.614222004030917)。
文摘As one of the most important steps in the design of bearing-less rotor systems,the design of flexible beam has received much research attention.Because of the very complex working environment of helicopter,the flexible beam should satisfy both the strength and dynamic requirements.However,traditional optimization research focused only on either the strength or dynamical characteristics.To sufficiently improve the performance of the flexible beam,both aspects must be considered.This paper proposes a two-stage optimization method based on the Hamilton variational principle:Variational asymptotic beam section analysis(VABS)program and genetic algorithm(GA).Consequently,a two-part analysis model based on the Hamilton variational principle and VABS is established to calculate section characteristics and structural dynamics characteristics,respectively.Subsequently,the two parts are combined to establish a two-stage optimization process and search with GA to obtain the best dynamic characteristics combinations.Based on the primary optimization results,the section characteristics of the flexible beam are further optimized using GA.The optimization results show that the torsional stiffness decreases by 36.1%compared with the full 0°laying scheme without optimization and the dynamic requirements are achieved.The natural frequencies of flapping and torsion meet the requirements(0.5 away from the passing frequencies of the blade,0.25 away from the excitation force frequency,and the flapping and torsion frequencies keep a corresponding distance).The results indicate that the optimization method can significantly improve the performance of the flexible beam.