Experimental studies are carried out at a low speed axial compressor with five different rotor/stator gaps. Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at...Experimental studies are carried out at a low speed axial compressor with five different rotor/stator gaps. Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at stall inception and on the flow range of compressor under multi-cell rotating stall operating conditions proves that the stator can suppress the flow disturbance in the compressor and strengthen the stability of the compressor. Experimental data show that the stall flow coefficient decreases by reducing the axial spacing of successive blade rows. Moreover, by reducing the axial spacing, the stall pattern transition pace from multi-cell stall to single-cell stall can be shifted. And the compressor directly slips into single-cell stall at 21.0% CR axial spacing. By analyzing the pressure fluctuation closed to the surge line, it can be known that there exists an eigenfrequency where the amplitude of the oscillating pressure suddenly and dramatically increases as the compressor runs close to the surge line and this pressure disturbance is relevant to the compressor instability.展开更多
Tilting pad gas journal bearing is one of the most widely used types of aerodynamic bearings due to its inherent excellent stability in high speed applications.A practical method for analyzing and calculating the per-...Tilting pad gas journal bearing is one of the most widely used types of aerodynamic bearings due to its inherent excellent stability in high speed applications.A practical method for analyzing and calculating the per- formances of such bearings is presented as well as its rotordynamics based on the computer aided technique.The method of calculation and the philosophy of programming with a microcomputer for the computer aided analysis are highlighted.展开更多
The stability and nonlinear dynamic behavior of drilling shaft system in copper stave deep hole drilling were analyzed. The effects of the fluctuation of the cutting force, the mass eccentricity and the hydrodynamic f...The stability and nonlinear dynamic behavior of drilling shaft system in copper stave deep hole drilling were analyzed. The effects of the fluctuation of the cutting force, the mass eccentricity and the hydrodynamic forces of cutting fluid could be taken into consideration in the model of drilling shaft system. Based on the isoparametric finite element method, the variational form of Reynolds equation in hydrodynamic fluid was used to calculate nonlinear hydrodynamic forces and their Jacobian matrices simultaneously. In the stability analysis, a new shooting method for rapidly determining the periodic orbit of the nonlinear drilling shaft system and its period was presented by rebuilding the traditional shooting method and changing the time scale. Through the combination of theories with experiment, the correctness and effectiveness of the above methods are verified by using the Floquet theory. The results show that the mass eccentricity can inhibit the whirling motion of drilling shaft to some extent.展开更多
Angiotensin （Ang）-（1-7） is recognized as a new bioactive peptide in renin-angiotensin system （RAS）. Ang-（1-7） is a counter-regulatory mediator of Ang-II which appears to be protective against cardiovascular di...Angiotensin （Ang）-（1-7） is recognized as a new bioactive peptide in renin-angiotensin system （RAS）. Ang-（1-7） is a counter-regulatory mediator of Ang-II which appears to be protective against cardiovascular disease. Recent studies have found that Ang-（1-7） played an important role in reducing smooth muscle cell proliferation and migration, improving endothelial function and regulating lipid metabolism, leading to inhibition of atherosclerotic lesions and increase of plaque stability. Although clinical application of Ang-（1-7） is restricted due to its pharmacokinetic properties, identification of stabilized compounds, including more stable analogues and specific delivery compounds, has enabled clinical application of Ang-（1-7）. In this review, we discussed recent findings concerning the biological role of Ang-（1-7） and related mechanism during atherosclerosis development. In addition, we highlighted the perspective to develop therapeutic strategies using Ang-（1-7） to treat atherosclerosis.展开更多
A nonlinear lateral-torsional coupled vibration model of a planetary gear system was established by taking transmission errors,time varying meshing stiffness and multiple gear backlashes into account.The bifurcation d...A nonlinear lateral-torsional coupled vibration model of a planetary gear system was established by taking transmission errors,time varying meshing stiffness and multiple gear backlashes into account.The bifurcation diagram of the system's motion state with rotational speed of sun gear was conducted through four steps.As a bifurcation parameter,the effect of rotational speed on the bifurcation properties of the system was assessed.The study results reveal that periodic motion is the main motion state of planetary gear train in low speed region when ns<2 350 r/min,but chaos motion state is dominant in high speed region when ns>2 350 r/min,The way of periodic motion to chaos is doubling bifurcation.There are two kinds of unstable modes and nine unstable regions in the speed region when 1 000 r/min<ns<3 000 r/min.展开更多
An essential dispersion relation,which can describe the dynamic properties of stimulated Raman scattering instability as a laser beam propagates through plasmas,is derived analytically.The development of growth mode,a...An essential dispersion relation,which can describe the dynamic properties of stimulated Raman scattering instability as a laser beam propagates through plasmas,is derived analytically.The development of growth mode,angle distribution,and temperature dependence of the instabilities are presented by solving this dispersion relation numerically.A significant dynamic characteristic has been revealed that the temperature increasing of the electron would result in redshift of scattered spectrum at high laser intensities.Furthermore,a novel modulational instability with double-peak temporal structure appears in a limited density region because of the coupling of scattered upshift and downshift waves.展开更多
The dynamics characteristics of the robotic arm system are usually highly nonlinear and strongly coupling,which will make it difficult to analyze the stability by the methods of solving kinetic equations or constructi...The dynamics characteristics of the robotic arm system are usually highly nonlinear and strongly coupling,which will make it difficult to analyze the stability by the methods of solving kinetic equations or constructing Lyapunov function,especially,these methods cannot calculate the quantitative relationship between mechanical structures or control input and dynamics parameters and stability.The theoretical analysis process from symbol dynamics modeling of the robotic arm system to the movement stability is studied by using the concept of Lyapunov exponents method. To verify the algorithm effectiveness,the inner relation between its joint input torque and stability or chaotic and stable motion of the 2-DOF robotic arm system is analyzed quantitatively. As compared with its counterpart of Lyapunov's direct method,the main advantage of the concept of Lyapunov exponents is that the methods for calculating the exponents are constructive to provide an effective analysis tool for analyzing robotic arm system movement stability of nonlinear systems.展开更多
In order to investigate the effect of a weak intercalation on slope stability, a large-scale shaking table model test was conducted to study the dynamic response of rock slope models with weak intercalation.The dynami...In order to investigate the effect of a weak intercalation on slope stability, a large-scale shaking table model test was conducted to study the dynamic response of rock slope models with weak intercalation.The dynamic response of the prototype slopes were studied in laboratory with the consideration of law of similitude. The initiation failure was observed in the rock slope model with a counter-tilt thin-weak intercalation firstly, not in the slope model with a horizontal thin-weak intercalation. Furthermore, it was interesting that the fracture site is shifted from crest top to the slope surface near the weak intercalation, which is different with the location of failure position in a normal layered slope. We also discussed the effect of the dip angle and the thickness of weak intercalation on the failure mechanism and instability mode of the layered rock slope. From the experimental result, it was noted that the stability of the slope with a counter-tilt weak intercalation could be worse than that of the other slopes under seismic excitation. The findings showed the difference of failure in slopes with a horizontal and counter weak intercalation, and implicated the further evaluation of failure of layered slopes caused by seismic loads.展开更多
This paper concentrates on investigating the mechanical stability of a Beam Position Monitor (BMP)support prototype of the Shanghai Synchrotron Radiation Facility(SSRF)project.Both finite element analysis and vibratio...This paper concentrates on investigating the mechanical stability of a Beam Position Monitor (BMP)support prototype of the Shanghai Synchrotron Radiation Facility(SSRF)project.Both finite element analysis and vibration measurements have been performed.Inconsistent results between the simulations and experiments motivate us to study three connections between the support and the ground:ground bolt(used in the initial design),part grout and full grout(proposed in the later research).After changing the connection, the first eigenfrequency is increased from 20.2Hz to 50.2Hz,and the ratio of the integrated RMS displacement (4—50Hz)is decreased from 4.36 to 1.23 in the lateral direction.The mechanical stability is improved greatly.展开更多
The DLE (dry low emission) technology has already been used on industrial gas turbine combustor and the NO X emission can be limited to 25 ppmv (@15% O 2 ), but one of the destructive effects is combustion instability...The DLE (dry low emission) technology has already been used on industrial gas turbine combustor and the NO X emission can be limited to 25 ppmv (@15% O 2 ), but one of the destructive effects is combustion instability. In this paper, the dynamic and emission characteristics of a DLE gas turbine combustor have been researched in the authors' laboratory, and the results show that the key source of combustion instability is the non-uniformity of fuel in the flame zone. Two main fuel supply methods have been used to form different fuel distribution types; it is shown that in the perfectly premixed case the emission level is low and combustion process is stable. The PPF also has an obvious effect on the combustor's emission and dynamic characteristics.展开更多
Through analyzing the motion characteristics of bird-like flapping flight, it is considered that the wing angular acceleration is equal to zero at the point of maximum angular speed. Thus, the flapping flight is equiv...Through analyzing the motion characteristics of bird-like flapping flight, it is considered that the wing angular acceleration is equal to zero at the point of maximum angular speed. Thus, the flapping flight is equivalent to a uniform rotating motion which can be analyzed by using the stream surface theory of turbomachinery during a micro period of time. In this article, the N-S equations of the motion are expanded in a non-orthogonal curvilinear coordinate system, and simplified on stream surfaces of the flapping flight model. By using stream function me- thod, the three-dimensional unsteady flow equations are simplified as a two-order partial differential equation with variable coefficients eventually and the equation＇s iterative solving method on S1 and $2 stream surfaces of the flapping flight model is presented. Through expanding the relatively steady equations of flapping flight at an arbitrary time point of a stroke on meridional plane of the flapping flight model, it can use a relatively steady mo- tion to approximate the real flapping flight at that time point, and analyze the flow stability influenced by the wing＇s flexibility. It can be seen that the wing flexibility is related to the higher pressurization capacity and the flow stability, and the pressurization capacity of flexible wing is proportional to the angular speed, angular distor- tion rate and radius square.展开更多
Numerical simulations were performed on the massively separated flows of a 76/40° double delta wing using detached-eddy simulation(DES).A new type of cross-flow vortex is suggested.A vortex was initially generate...Numerical simulations were performed on the massively separated flows of a 76/40° double delta wing using detached-eddy simulation(DES).A new type of cross-flow vortex is suggested.A vortex was initially generated near the junction of the strake and wing,which then moved towards the wing tip at certain wavelength and speed.Analyses were made in detail on the mechanism of the generation of the cross-flow vortex,that is,the inviscid cross-flow instability which differs from that of the swept blunt wing.Cross-section topology of the cross-flow vortex is also investigated,and the wavelength of the vortex array and the characteristic frequency are given.The analyses showed that the cross-flow vortices have an influence on the pressure distribution,which can cause a 10%-20% deviation from the averaged distribution.展开更多
This paper deals with the problem of the instability regions of a free-free flexible jointed bipartite beam under the follower and transversal forces as a realistic simulation of a two-stage aerospace structure. The a...This paper deals with the problem of the instability regions of a free-free flexible jointed bipartite beam under the follower and transversal forces as a realistic simulation of a two-stage aerospace structure. The aim of this study is to analyze the effects of the characteristics of a flexible joint on the beam instability to use maximum bearable propulsion force. A parametric study is conducted to investigate the effects of the stiffness and the location of the joint on the critical follower force by the Ritz method and the Newmark method, then to research the vibrational properties of the structure. It has been shown that the nature of instability is quite unpredictable and dependent on the stiffness and the location of the joint. The increase of the follower force or the transversal force will increase the vibration of the model and consequently cause a destructive phenomenon in the control system of the aerospace structure. Furthermore, this paper introduces a new concept of the parametric approach to analyze the characteristics effects of a flexible two-stage aerospace structure joint design.展开更多
文摘Experimental studies are carried out at a low speed axial compressor with five different rotor/stator gaps. Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at stall inception and on the flow range of compressor under multi-cell rotating stall operating conditions proves that the stator can suppress the flow disturbance in the compressor and strengthen the stability of the compressor. Experimental data show that the stall flow coefficient decreases by reducing the axial spacing of successive blade rows. Moreover, by reducing the axial spacing, the stall pattern transition pace from multi-cell stall to single-cell stall can be shifted. And the compressor directly slips into single-cell stall at 21.0% CR axial spacing. By analyzing the pressure fluctuation closed to the surge line, it can be known that there exists an eigenfrequency where the amplitude of the oscillating pressure suddenly and dramatically increases as the compressor runs close to the surge line and this pressure disturbance is relevant to the compressor instability.
文摘Tilting pad gas journal bearing is one of the most widely used types of aerodynamic bearings due to its inherent excellent stability in high speed applications.A practical method for analyzing and calculating the per- formances of such bearings is presented as well as its rotordynamics based on the computer aided technique.The method of calculation and the philosophy of programming with a microcomputer for the computer aided analysis are highlighted.
基金Project(2007CB707706) supported by the Major State Basic Research Development Program of ChinaProjects(2007E213,2007E203) supported by the Natural Science Foundation of Shaanxi Province,China
文摘The stability and nonlinear dynamic behavior of drilling shaft system in copper stave deep hole drilling were analyzed. The effects of the fluctuation of the cutting force, the mass eccentricity and the hydrodynamic forces of cutting fluid could be taken into consideration in the model of drilling shaft system. Based on the isoparametric finite element method, the variational form of Reynolds equation in hydrodynamic fluid was used to calculate nonlinear hydrodynamic forces and their Jacobian matrices simultaneously. In the stability analysis, a new shooting method for rapidly determining the periodic orbit of the nonlinear drilling shaft system and its period was presented by rebuilding the traditional shooting method and changing the time scale. Through the combination of theories with experiment, the correctness and effectiveness of the above methods are verified by using the Floquet theory. The results show that the mass eccentricity can inhibit the whirling motion of drilling shaft to some extent.
基金This work was supported by National Natural Science Foundation of China （NSFC） （No. 81400265 and No. 81270274）, and Peking University People＇s Hospital Research and Development funds （RDB2014-16）.
文摘Angiotensin （Ang）-（1-7） is recognized as a new bioactive peptide in renin-angiotensin system （RAS）. Ang-（1-7） is a counter-regulatory mediator of Ang-II which appears to be protective against cardiovascular disease. Recent studies have found that Ang-（1-7） played an important role in reducing smooth muscle cell proliferation and migration, improving endothelial function and regulating lipid metabolism, leading to inhibition of atherosclerotic lesions and increase of plaque stability. Although clinical application of Ang-（1-7） is restricted due to its pharmacokinetic properties, identification of stabilized compounds, including more stable analogues and specific delivery compounds, has enabled clinical application of Ang-（1-7）. In this review, we discussed recent findings concerning the biological role of Ang-（1-7） and related mechanism during atherosclerosis development. In addition, we highlighted the perspective to develop therapeutic strategies using Ang-（1-7） to treat atherosclerosis.
基金Project(50775108) supported by the National Natural Science Foundation of China
文摘A nonlinear lateral-torsional coupled vibration model of a planetary gear system was established by taking transmission errors,time varying meshing stiffness and multiple gear backlashes into account.The bifurcation diagram of the system's motion state with rotational speed of sun gear was conducted through four steps.As a bifurcation parameter,the effect of rotational speed on the bifurcation properties of the system was assessed.The study results reveal that periodic motion is the main motion state of planetary gear train in low speed region when ns<2 350 r/min,but chaos motion state is dominant in high speed region when ns>2 350 r/min,The way of periodic motion to chaos is doubling bifurcation.There are two kinds of unstable modes and nine unstable regions in the speed region when 1 000 r/min<ns<3 000 r/min.
文摘An essential dispersion relation,which can describe the dynamic properties of stimulated Raman scattering instability as a laser beam propagates through plasmas,is derived analytically.The development of growth mode,angle distribution,and temperature dependence of the instabilities are presented by solving this dispersion relation numerically.A significant dynamic characteristic has been revealed that the temperature increasing of the electron would result in redshift of scattered spectrum at high laser intensities.Furthermore,a novel modulational instability with double-peak temporal structure appears in a limited density region because of the coupling of scattered upshift and downshift waves.
基金Supported by the National Natural Science Foundation of China(No.51405243,51575283)
文摘The dynamics characteristics of the robotic arm system are usually highly nonlinear and strongly coupling,which will make it difficult to analyze the stability by the methods of solving kinetic equations or constructing Lyapunov function,especially,these methods cannot calculate the quantitative relationship between mechanical structures or control input and dynamics parameters and stability.The theoretical analysis process from symbol dynamics modeling of the robotic arm system to the movement stability is studied by using the concept of Lyapunov exponents method. To verify the algorithm effectiveness,the inner relation between its joint input torque and stability or chaotic and stable motion of the 2-DOF robotic arm system is analyzed quantitatively. As compared with its counterpart of Lyapunov's direct method,the main advantage of the concept of Lyapunov exponents is that the methods for calculating the exponents are constructive to provide an effective analysis tool for analyzing robotic arm system movement stability of nonlinear systems.
基金financially supported by the Research and Innovation Team of Chengdu University of TechnologyProject of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection (Grant No. SKLGP2013Z002)
文摘In order to investigate the effect of a weak intercalation on slope stability, a large-scale shaking table model test was conducted to study the dynamic response of rock slope models with weak intercalation.The dynamic response of the prototype slopes were studied in laboratory with the consideration of law of similitude. The initiation failure was observed in the rock slope model with a counter-tilt thin-weak intercalation firstly, not in the slope model with a horizontal thin-weak intercalation. Furthermore, it was interesting that the fracture site is shifted from crest top to the slope surface near the weak intercalation, which is different with the location of failure position in a normal layered slope. We also discussed the effect of the dip angle and the thickness of weak intercalation on the failure mechanism and instability mode of the layered rock slope. From the experimental result, it was noted that the stability of the slope with a counter-tilt weak intercalation could be worse than that of the other slopes under seismic excitation. The findings showed the difference of failure in slopes with a horizontal and counter weak intercalation, and implicated the further evaluation of failure of layered slopes caused by seismic loads.
文摘This paper concentrates on investigating the mechanical stability of a Beam Position Monitor (BMP)support prototype of the Shanghai Synchrotron Radiation Facility(SSRF)project.Both finite element analysis and vibration measurements have been performed.Inconsistent results between the simulations and experiments motivate us to study three connections between the support and the ground:ground bolt(used in the initial design),part grout and full grout(proposed in the later research).After changing the connection, the first eigenfrequency is increased from 20.2Hz to 50.2Hz,and the ratio of the integrated RMS displacement (4—50Hz)is decreased from 4.36 to 1.23 in the lateral direction.The mechanical stability is improved greatly.
基金supported by the National Natural Science Foundation of China(No.50976116and No.50806077)
文摘The DLE (dry low emission) technology has already been used on industrial gas turbine combustor and the NO X emission can be limited to 25 ppmv (@15% O 2 ), but one of the destructive effects is combustion instability. In this paper, the dynamic and emission characteristics of a DLE gas turbine combustor have been researched in the authors' laboratory, and the results show that the key source of combustion instability is the non-uniformity of fuel in the flame zone. Two main fuel supply methods have been used to form different fuel distribution types; it is shown that in the perfectly premixed case the emission level is low and combustion process is stable. The PPF also has an obvious effect on the combustor's emission and dynamic characteristics.
文摘Through analyzing the motion characteristics of bird-like flapping flight, it is considered that the wing angular acceleration is equal to zero at the point of maximum angular speed. Thus, the flapping flight is equivalent to a uniform rotating motion which can be analyzed by using the stream surface theory of turbomachinery during a micro period of time. In this article, the N-S equations of the motion are expanded in a non-orthogonal curvilinear coordinate system, and simplified on stream surfaces of the flapping flight model. By using stream function me- thod, the three-dimensional unsteady flow equations are simplified as a two-order partial differential equation with variable coefficients eventually and the equation＇s iterative solving method on S1 and $2 stream surfaces of the flapping flight model is presented. Through expanding the relatively steady equations of flapping flight at an arbitrary time point of a stroke on meridional plane of the flapping flight model, it can use a relatively steady mo- tion to approximate the real flapping flight at that time point, and analyze the flow stability influenced by the wing＇s flexibility. It can be seen that the wing flexibility is related to the higher pressurization capacity and the flow stability, and the pressurization capacity of flexible wing is proportional to the angular speed, angular distor- tion rate and radius square.
基金sponsored by the National Natural Science Foundation of China (Grant No. 91016001)
文摘Numerical simulations were performed on the massively separated flows of a 76/40° double delta wing using detached-eddy simulation(DES).A new type of cross-flow vortex is suggested.A vortex was initially generated near the junction of the strake and wing,which then moved towards the wing tip at certain wavelength and speed.Analyses were made in detail on the mechanism of the generation of the cross-flow vortex,that is,the inviscid cross-flow instability which differs from that of the swept blunt wing.Cross-section topology of the cross-flow vortex is also investigated,and the wavelength of the vortex array and the characteristic frequency are given.The analyses showed that the cross-flow vortices have an influence on the pressure distribution,which can cause a 10%-20% deviation from the averaged distribution.
文摘This paper deals with the problem of the instability regions of a free-free flexible jointed bipartite beam under the follower and transversal forces as a realistic simulation of a two-stage aerospace structure. The aim of this study is to analyze the effects of the characteristics of a flexible joint on the beam instability to use maximum bearable propulsion force. A parametric study is conducted to investigate the effects of the stiffness and the location of the joint on the critical follower force by the Ritz method and the Newmark method, then to research the vibrational properties of the structure. It has been shown that the nature of instability is quite unpredictable and dependent on the stiffness and the location of the joint. The increase of the follower force or the transversal force will increase the vibration of the model and consequently cause a destructive phenomenon in the control system of the aerospace structure. Furthermore, this paper introduces a new concept of the parametric approach to analyze the characteristics effects of a flexible two-stage aerospace structure joint design.
