采用微波焙烧法和常规焙烧方法分别制备了一种新型的无机非金属材料纳米氧化铁,并研究了氧化铁晶粒生长动力学。使用扫描电镜、热重分析仪、傅里叶变换红外光谱仪和X射线衍射仪对前驱体和纳米氧化铁进行表征。结果表明:在相同焙烧温度...采用微波焙烧法和常规焙烧方法分别制备了一种新型的无机非金属材料纳米氧化铁,并研究了氧化铁晶粒生长动力学。使用扫描电镜、热重分析仪、傅里叶变换红外光谱仪和X射线衍射仪对前驱体和纳米氧化铁进行表征。结果表明:在相同焙烧温度和时间下,微波焙烧氧化铁的晶粒尺寸要明显大于常规焙烧方式,同时,微波制备的试样颗粒大小更均匀。微波焙烧和常规焙烧下氧化铁的晶粒生长平均动力学指数分别是4.493和5.133,晶粒生长的平均活化能分别为24.30 k J/mol和30.43 k J/mol。表明微波焙烧有利于晶粒生长,晶粒的平均生长速率较高。展开更多
Effectiveness of microwave sintering process through investigation of microstructural characteristics and electrical properties of x(0.94PbZn_ 1/3Nb_ 2/3O_3 + 0.06BaTiO_3)+(1-x)PbZr_yTi_ 1-yO_3(PBZNZT)ceramics with x=...Effectiveness of microwave sintering process through investigation of microstructural characteristics and electrical properties of x(0.94PbZn_ 1/3Nb_ 2/3O_3 + 0.06BaTiO_3)+(1-x)PbZr_yTi_ 1-yO_3(PBZNZT)ceramics with x=0.6 and y=0.52 was evaluated.The relative density of 95% was achieved with sintering at 800℃ for 2 h.The small grain growth exponents indicate how easy the grain growth in these materials sintered using microwave radiation.Grain growth rate increases abruptly and is higher than that of conventional sintering at a temperature higher than 1050℃.This is attributed to the lower activation energy and higher grain boundary mobility.The activation energy required for the grain growth is found to be 132kJ/mol.Higher remanent polarization(Pr=50.1μC/cm2)and increase in remanent polarization with sintering temperature are observed in microwave sintering process when compared to that of conventional sintering process,due to fast increase in grain growth rate and homogeneity in the specimen.The results indicate lower sintering energy and reduction of PbO pollution in the working environment by microwave sintering process.展开更多
The grain growth morphology,kinetics and texture change after uniaxial compression at 430 ℃ of an extruded AZ31 alloy were studied.The samples were loaded following two routes insuring two initial textures of the sam...The grain growth morphology,kinetics and texture change after uniaxial compression at 430 ℃ of an extruded AZ31 alloy were studied.The samples were loaded following two routes insuring two initial textures of the samples with compression direction parallel and normal to the extrusion direction.For both initial textures,a stable grain size is attained upon isothermal annealing and the grain growth kinetics can be described by:dn= dRn+kt with an n value of around 15.The annealing texture with grown grains is a retained hot deformation texture without emerging or strengthening other components.Abnormal grain growth is not observed for annealing time up to 10 000 h at 450℃.展开更多
Transient liquid phase(TLP)bonding is a potential high-temperature(HT)electron packaging technology that is used inthe interconnection of wide band-gap semiconductors.This study focused on the mechanism of intermetall...Transient liquid phase(TLP)bonding is a potential high-temperature(HT)electron packaging technology that is used inthe interconnection of wide band-gap semiconductors.This study focused on the mechanism of intermetallic compounds(IMCs)evolution in Ag/Sn TLP soldering at different temperatures.Experimental results indicated that morphologies of Ag3Sn grains mainlywere scallop-type,and some other shapes such as prism,needle,hollow column,sheet and wire of Ag3Sn grains were also observed,which was resulted from their anisotropic growths.However,the scallop-type Ag3Sn layer turned into more planar with prolongingsoldering time,due to grain coarsening and anisotropic mass flow of Ag atoms from substrate.Furthermore,a great amount ofnano-Ag3Sn particles were found on the surfaces of Ag3Sn grains,which were formed in Ag-rich areas of the molten Sn and adsorbedby the Ag3Sn grains during solidification process.Growth kinetics of the Ag3Sn IMCs in TLP soldering followed a parabolicrelationship with soldering time,and the growth rate constants of250,280and320°C were calculated as5.83×10-15m2/s,7.83×10-15m2/s and2.83×10-14m2/s,respectively.Accordingly,the activation energy of the reaction was estimated about58.89kJ/mol.展开更多
A heightened understanding of nucleation and growth mechanisms is paramount if effective solution processing of organic-inorganic perovskite thin-films for optoelectronic applications is to be achieved. Many fabri- ca...A heightened understanding of nucleation and growth mechanisms is paramount if effective solution processing of organic-inorganic perovskite thin-films for optoelectronic applications is to be achieved. Many fabri- cation techniques have been utilized previously to develop high-performance perovskite layers but there remains an absence of a unifying model that describes accurately the formation of these materials from solution. The present study provides a thorough analysis of nucleation and growth kinetics underpinning the development of hybrid organic-in- organic perovskite thin-films. Through precise control of the perovskite growth conditions the spacing of heteroge- neous nucleation sites was varied successfully from several hundred nanometers to several hundred microns. The crystalline regions surrounding these nuclei were found to comprise clusters of highly-oriented crystal domains exceed- ing 100 pm in diameter. However, no beneficial correlation was found between the size of these well-oriented grain-clus- ters and the optoelectronic performance. The formation of the perovskite microstructure features characteristics of both classical and non-classical growth mechanisms. The insights into perovskite thin-film growth developed by the present study provide clear implications for the development of future hybrid perovskite microstructures.展开更多
Nanoparticles in solution offer unique electrical, mechanical and thermal properties due to their physical presence and interac- tion with the state of dispersion. This work is aimed to study the effects of hydroxyapa...Nanoparticles in solution offer unique electrical, mechanical and thermal properties due to their physical presence and interac- tion with the state of dispersion. This work is aimed to study the effects of hydroxyapatite （HA） nanoparticles on the behavior of devitrification and recrystallization of glycerol （60% w/w） and PEG-600 （50% w/w） solutions during warming. HA nano- particles of different sizes （20, 40, 60 nm） and concentrations （0.1%, 0.5%, w/w） were incorporated into solutions, and were studied by calorimetric analysis coupled with cryomicroscopy. The presence of HA nanoparticles has little effect on the devit- rification end temperatures, but affects the devitrification onset temperatures of glycerol and PEG-600 solutions. The investi- gation with the cryomicroscope observed that the ice morphologies of glycerol and PEG-600 solutions are dendritic and spher- ic respectively. The ice fraction of glycerol solution containing 0.1% HA with the size of 60 nm decreased to 2/5 of that of the solution without nanoparticles at -45℃. The ice fractions of PEG-600 solutions increased signifcantly between -64℃ and -54℃, and the ice fraction of PEG-600 solution without nanoparticles increased by 92% within the temperature range. The findings have significant implications for biomaterial cryopreservation, cryosurgery, and food manufacturing. The complexity of ice crystal growth kinetics in nanoparticle-containing solutions awaits further study.展开更多
文摘采用微波焙烧法和常规焙烧方法分别制备了一种新型的无机非金属材料纳米氧化铁,并研究了氧化铁晶粒生长动力学。使用扫描电镜、热重分析仪、傅里叶变换红外光谱仪和X射线衍射仪对前驱体和纳米氧化铁进行表征。结果表明:在相同焙烧温度和时间下,微波焙烧氧化铁的晶粒尺寸要明显大于常规焙烧方式,同时,微波制备的试样颗粒大小更均匀。微波焙烧和常规焙烧下氧化铁的晶粒生长平均动力学指数分别是4.493和5.133,晶粒生长的平均活化能分别为24.30 k J/mol和30.43 k J/mol。表明微波焙烧有利于晶粒生长,晶粒的平均生长速率较高。
文摘Effectiveness of microwave sintering process through investigation of microstructural characteristics and electrical properties of x(0.94PbZn_ 1/3Nb_ 2/3O_3 + 0.06BaTiO_3)+(1-x)PbZr_yTi_ 1-yO_3(PBZNZT)ceramics with x=0.6 and y=0.52 was evaluated.The relative density of 95% was achieved with sintering at 800℃ for 2 h.The small grain growth exponents indicate how easy the grain growth in these materials sintered using microwave radiation.Grain growth rate increases abruptly and is higher than that of conventional sintering at a temperature higher than 1050℃.This is attributed to the lower activation energy and higher grain boundary mobility.The activation energy required for the grain growth is found to be 132kJ/mol.Higher remanent polarization(Pr=50.1μC/cm2)and increase in remanent polarization with sintering temperature are observed in microwave sintering process when compared to that of conventional sintering process,due to fast increase in grain growth rate and homogeneity in the specimen.The results indicate lower sintering energy and reduction of PbO pollution in the working environment by microwave sintering process.
文摘The grain growth morphology,kinetics and texture change after uniaxial compression at 430 ℃ of an extruded AZ31 alloy were studied.The samples were loaded following two routes insuring two initial textures of the samples with compression direction parallel and normal to the extrusion direction.For both initial textures,a stable grain size is attained upon isothermal annealing and the grain growth kinetics can be described by:dn= dRn+kt with an n value of around 15.The annealing texture with grown grains is a retained hot deformation texture without emerging or strengthening other components.Abnormal grain growth is not observed for annealing time up to 10 000 h at 450℃.
基金Project(51375260) supported by the National Natural Science Foundation of China
文摘Transient liquid phase(TLP)bonding is a potential high-temperature(HT)electron packaging technology that is used inthe interconnection of wide band-gap semiconductors.This study focused on the mechanism of intermetallic compounds(IMCs)evolution in Ag/Sn TLP soldering at different temperatures.Experimental results indicated that morphologies of Ag3Sn grains mainlywere scallop-type,and some other shapes such as prism,needle,hollow column,sheet and wire of Ag3Sn grains were also observed,which was resulted from their anisotropic growths.However,the scallop-type Ag3Sn layer turned into more planar with prolongingsoldering time,due to grain coarsening and anisotropic mass flow of Ag atoms from substrate.Furthermore,a great amount ofnano-Ag3Sn particles were found on the surfaces of Ag3Sn grains,which were formed in Ag-rich areas of the molten Sn and adsorbedby the Ag3Sn grains during solidification process.Growth kinetics of the Ag3Sn IMCs in TLP soldering followed a parabolicrelationship with soldering time,and the growth rate constants of250,280and320°C were calculated as5.83×10-15m2/s,7.83×10-15m2/s and2.83×10-14m2/s,respectively.Accordingly,the activation energy of the reaction was estimated about58.89kJ/mol.
基金the financial support from the Australian Renewable Energy Agency (ARENA)the Australian Centre for Advanced Photovoltaics (ACAP)the ARC Centre of Excellence in Exciton Science
文摘A heightened understanding of nucleation and growth mechanisms is paramount if effective solution processing of organic-inorganic perovskite thin-films for optoelectronic applications is to be achieved. Many fabri- cation techniques have been utilized previously to develop high-performance perovskite layers but there remains an absence of a unifying model that describes accurately the formation of these materials from solution. The present study provides a thorough analysis of nucleation and growth kinetics underpinning the development of hybrid organic-in- organic perovskite thin-films. Through precise control of the perovskite growth conditions the spacing of heteroge- neous nucleation sites was varied successfully from several hundred nanometers to several hundred microns. The crystalline regions surrounding these nuclei were found to comprise clusters of highly-oriented crystal domains exceed- ing 100 pm in diameter. However, no beneficial correlation was found between the size of these well-oriented grain-clus- ters and the optoelectronic performance. The formation of the perovskite microstructure features characteristics of both classical and non-classical growth mechanisms. The insights into perovskite thin-film growth developed by the present study provide clear implications for the development of future hybrid perovskite microstructures.
基金supported by the National Natural Science Foundation of China(Grant No.51076108)the Doctoral Program(Grant No.20103120110005)the Shanghai Dongfang Scholars Program
文摘Nanoparticles in solution offer unique electrical, mechanical and thermal properties due to their physical presence and interac- tion with the state of dispersion. This work is aimed to study the effects of hydroxyapatite （HA） nanoparticles on the behavior of devitrification and recrystallization of glycerol （60% w/w） and PEG-600 （50% w/w） solutions during warming. HA nano- particles of different sizes （20, 40, 60 nm） and concentrations （0.1%, 0.5%, w/w） were incorporated into solutions, and were studied by calorimetric analysis coupled with cryomicroscopy. The presence of HA nanoparticles has little effect on the devit- rification end temperatures, but affects the devitrification onset temperatures of glycerol and PEG-600 solutions. The investi- gation with the cryomicroscope observed that the ice morphologies of glycerol and PEG-600 solutions are dendritic and spher- ic respectively. The ice fraction of glycerol solution containing 0.1% HA with the size of 60 nm decreased to 2/5 of that of the solution without nanoparticles at -45℃. The ice fractions of PEG-600 solutions increased signifcantly between -64℃ and -54℃, and the ice fraction of PEG-600 solution without nanoparticles increased by 92% within the temperature range. The findings have significant implications for biomaterial cryopreservation, cryosurgery, and food manufacturing. The complexity of ice crystal growth kinetics in nanoparticle-containing solutions awaits further study.
