In order to investigate the material properties ofperiodontal ligament （ PDL） in different locations, the nanoindentation method is used to survey the elastic modulus of the PDL at different levels. Cadaveric specim...In order to investigate the material properties ofperiodontal ligament （ PDL） in different locations, the nanoindentation method is used to survey the elastic modulus of the PDL at different levels. Cadaveric specimens of human mandibular canine were obtained from 4 adult donors, 16 transverse specimens were made from the sections of cervical margin, midroot and apex using the slow cutting machine. The prepared specimens were tested in different sections （along the longitudinal direction） and different areas （in the circumferential direction）. According to the Oliver-Phair theory, the mean values of elastic modulus were calculated foreach area and the differences among them were compared. In the midroot section, the average elastic modulus is ranging from 0. 11 to 0. 23 MPa, the changing range of the cervical margin and apex are from 0. 21 to 0. 53 MPa and 0. 44 to0.62 MPa, respectively. Experimental results indicate that the average elastic modulus in the midroot is lower than that in the cervical margin and apex, and relatively small changes occur among them. However, there is a large change to the elastic modulus value in the cicumferential direction for the PDL.展开更多
A combined method of selective laser sintering （SLS） and cold isostatic pressing （CIP） was applied to manufacturing metal parts rapidly. Finite element method was used to predict final dimensions and decrease cost...A combined method of selective laser sintering （SLS） and cold isostatic pressing （CIP） was applied to manufacturing metal parts rapidly. Finite element method was used to predict final dimensions and decrease cost. The simulations of CIP of selective laser sintered parts were carried out by Drucker-Prager-Cap constitutive model with ABAQUS computer program. The property of metal powder was measured by CIP experiments. The results show the rubber bag and the friction coefficient have little influence on results of simulations. The parts only have uniform shrinkage and have no obvious distortion in shape. The results of simulations show a good agreement with the experimental results and the calculated results, indicating that the Drucker-Prager-Cap model is an effective model to simulate CIP process. The simulations could give a useful direction to forming process of the CIP of selective laser sintered components. K展开更多
Under natural conditions, the use of vapor pressure deficit between mesophyll cell surface and ambient air ( VPD s ) instead of atmospheric humidity factors in some stomatal models may markedly promote the applicabil...Under natural conditions, the use of vapor pressure deficit between mesophyll cell surface and ambient air ( VPD s ) instead of atmospheric humidity factors in some stomatal models may markedly promote the applicability of stomatal models. It has been pointed out from theoretical analysis that the expression of the responses of stomatal conductance to VPD s is equivalent to the expression of responses of stomatal conductance to water loss of transpiration in stomatal models.展开更多
A novel, highly linear sampling switch suitable for low-voltage operation is proposed. This switch not only eliminates the nonlinearity introduced by gate-source voltage variation, but also reduces the nonlinearity re...A novel, highly linear sampling switch suitable for low-voltage operation is proposed. This switch not only eliminates the nonlinearity introduced by gate-source voltage variation, but also reduces the nonlinearity resuiting from threshold voltage variation, which has not been accomplished in earlier low-voltage sampling switches. This is achieved by adopting a replica transistor with the same threshold voltage as the sampling transistor. The effectiveness of this technique is demonstrated by a prototype design of a sampling switch in 0. 35μm. The proposed sampling switch achieves a spurious free dynamic range of 111dB for a 0. 2MHz, 1.2Vp-p input signal, sampled at a rate of 2MS/s,about 18dB over the Bootstrapped switch. Also, the on-resistance variation is reduced by 90%. This method is especially useful for low-voltage, high resolution ADCs, which is a hot topic today.展开更多
Operational reliability evaluation theory reflects real-time reliability level of power system. The component failure rate varies with operating conditions. The impact of real-time operating conditions such as ambient...Operational reliability evaluation theory reflects real-time reliability level of power system. The component failure rate varies with operating conditions. The impact of real-time operating conditions such as ambient temperature and transformer MVA (megavolt-ampere) loading on transformer insulation life is studied in this paper. The formula of transformer failure rate based on the winding hottest-spot temperature (HST) is given. Thus the real-time reliability model of transformer based on oper- ating conditions is presented. The work is illustrated using the 1979 IEEE Reliability Test System. The changes of operating conditions are simulated by using hourly load curve and temperature curve, so the curves of real-time reliability indices are ob- tained by using operational reliability evaluation.展开更多
The two-stage gas boriding in N_(2)−H_(2)−BCl_(3)atmosphere was applied to producing a two-zoned borided layer on Nisil-alloy.The process was carried out at 910℃ for 2 h.The microstructure consisted of two zones diff...The two-stage gas boriding in N_(2)−H_(2)−BCl_(3)atmosphere was applied to producing a two-zoned borided layer on Nisil-alloy.The process was carried out at 910℃ for 2 h.The microstructure consisted of two zones differing in their phase composition.The outer layer contained only a mixture of nickel borides(Ni_(2)B,Ni_(3)B)only.The inner zone contained additionally nickel silicides(Ni_(2)Si,Ni_(3)Si)occurring together with nickel borides.The aim of this study was to determine the presence of nickel silicides on the mechanical properties of the borided layer produced on Ni-based alloy.The hardness and elastic modulus were measured using the nanoindenter with a Berkovich diamond tip under a load of 50 mN.The average values of indentation hardness(HI)and indentation elastic modulus(E_(I))obtained in the outer zone were respectively(16.32±1.03)GPa and(232±16.15)GPa.The presence of nickel silicides in the inner zone reduced the indentation hardness(6.8−12.54 GPa)and elastic modulus(111.79−153.99 GPa).The fracture toughness of the boride layers was investigated using a Vickers microindentation under a load of 0.981 N.It was confirmed that the presence of nickel silicides caused an increase in brittleness(by about 40%)of the gas-borided layer.展开更多
As a frequently-used roadbed filler,soil-rock mixture is often in the environment of freeze-thaw cycles and different confining pressures.In order to study the freeze-thaw damage mechanism of elastic modulus of soil-r...As a frequently-used roadbed filler,soil-rock mixture is often in the environment of freeze-thaw cycles and different confining pressures.In order to study the freeze-thaw damage mechanism of elastic modulus of soil-rock mixtures at different confining pressures,the concept of meso-interfacial freeze-thaw damage coefficient is put forward and the meso-interfacial damage phenomenon of soil-rock mixtures caused by the freeze-thaw cycle environment is concerned;a double-inclusion embedded model for elastic modulus of soil-rock mixtures in freezing-thawing cycle is proposed.A large triaxial test was performed and the influences of confining pressure and experimental factors on elastic modulus of soil-rock mixtures were obtained,and then the accuracy of the double-inclusion embedded model to predict the elastic modulus of soil-rock mixtures in freezing-thawing cycle is verified.Experiment results showed that as to soil-rock mixtures,with the increase of confining pressure,the elastic modulus increases approximately linearly.The most crucial factors to affect the elastic modulus are rock content and compaction degree at the same confining pressure;the elastic modulus increases with the increase of rock content and compactness;as the number of freeze-thaw cycles increases,the freeze-thaw damage coefficient of meso-structural interface and the elastic modulus decrease.展开更多
The uniaxial compression tests for mudstone specimens are carried out with four different loading rates from room temperature to 400℃ by using the Rock Mechanics Servo-controlled Testing System MTS810 and high temper...The uniaxial compression tests for mudstone specimens are carried out with four different loading rates from room temperature to 400℃ by using the Rock Mechanics Servo-controlled Testing System MTS810 and high temperature furnace MTS652.02.The mechanical properties of mudstone with various loading rates are studied under different temperature conditions.The results show that when temperature increases from room temperature to 400℃ and loading rate is less than 0.03 mm/s,the peak strength of mudstone specimen decreases as loading rate increases,while the various peak strengths show significant differences when loading rate exceeds 0.03 mm/s.At room temperature,the elastic modulus decreases at the first time and then increases with loading rate rising.When the temperature is between200 and 400℃,the elastic modulus presents a decreasing trend with increasing loading rate.With increasing the loading rate,the number of fragments in mudstone becomes larger and even the powder is observed in mudstone with higher loading rate.Under high loading rate,the failure mode of mudstone specimens under different temperatures is mainly conical damage.展开更多
Cracking gas compressor is usually a centrifugal compressor. The information on the performance of a centrifugal compressor under all conditions is not available, which restricts the operation optimization for compres...Cracking gas compressor is usually a centrifugal compressor. The information on the performance of a centrifugal compressor under all conditions is not available, which restricts the operation optimization for compressor. To solve this problem, two back propagation (BP) neural networks were introduced to model the performance of a compressor by using the data provided by manufacturer. The input data of the model under other conditions should be corrected according to the similarity theory. The method was used to optimize the system of a cracking gas compressor by embedding the compressor performance model into the ASPEN PLUS model of compressor. The result shows that it is an effective method to optimize the compressor system.展开更多
We study a system consisting of two identical non-interacting single-mode cavity fields coupled to a common vacuum environment and provide general, explicit, and exact solutions to its master equation by means of the ...We study a system consisting of two identical non-interacting single-mode cavity fields coupled to a common vacuum environment and provide general, explicit, and exact solutions to its master equation by means of the characteristic function method. We analyze the entanglement dynamics of two-mode squeezed thermal state in this model and show that its entanglement dynamics is strongly determined by the two-mode squeezing parameter and the purity. In particular, we find that two-mode squeezed thermal state with the squeezing parameter r ≤ -（1/2） In √u is extremely fragile and almost does not survive in a common vacuum environment. We investigate the time evolution of nonlocality for two-mode squeezed thermal state in such an environment. It is found that the evolved state loses its nonlocality in the beginning of the evolution, but after a time, the revival of nonlocality can occur.展开更多
Zn-22 Al alloy closed-cell foams were fabricated by melt foaming process using hydride foaming agent. The compressive properties were investigated under quasi-static condition. The structure of the foamed material was...Zn-22 Al alloy closed-cell foams were fabricated by melt foaming process using hydride foaming agent. The compressive properties were investigated under quasi-static condition. The structure of the foamed material was analyzed during compression test to reveal the relationship between morphology and compressive behavior. The results show that the stress-strain behavior is typical of closed-cell metal foams and mostly of brittle type. Governing deformation mechanism at plateau stage is identified to be brittle crushing. A substantial increase in compressive strength of Zn-22 Al foams was obtained. The agreement between compressive properties and Gibson-Ashby model was also detected.展开更多
A step-by-step load was utilized to mimic the load history of the backfill column in the in-situ curing process.The inner damage of the specimen during curing and uniaxial compressive testing was monitored by electric...A step-by-step load was utilized to mimic the load history of the backfill column in the in-situ curing process.The inner damage of the specimen during curing and uniaxial compressive testing was monitored by electrical resistivity and ultrasonic equipment.Results show that:1)Uniaxial compressive strength(UCS)and elastic modulus(EM)of the samples curing under pressure are higher than those of the control samples without pressure,ranging in ratio from 0.5%to 20.2%and 7.1%to 52.3%,respectively,and are influenced by the initial loading age(ILA)and stress strength ratio(SSR).The SSR during curing should not exceed 80%.2)The earlier the ILA is,the higher the total strain becomes.The higher the SSR applies,the larger the total strain gets.The creep strain increases with the increase of SSR and can be described by Burger’s viscoelastic creep model.When SSR is less than 80%,the earlier the ILA is,the smaller the creep strain becomes after the last step-loading.3)The stability of the early age backfill column under pressure can be monitored based on the change of ultrasonic pulse velocity(UPV)and electrical resistivity.展开更多
AIM： To study the stability of portal hypertension （PHT） caused by partial ligation of the portal vein ligation （PVL） in a rat model.METHODS： Thirty male adult Wistar rats were divided into two groups： 10 in Gr...AIM： To study the stability of portal hypertension （PHT） caused by partial ligation of the portal vein ligation （PVL） in a rat model.METHODS： Thirty male adult Wistar rats were divided into two groups： 10 in Group Ⅰ received a sham operation; and 20 in Group Ⅱreceived partial PVL. Portal vein pressure （PVP） was measured at four time periods： before ligation, 2 wk, 6 wk and 10 wk postsurgery. Portal venography, blood sampling and liver and spleen pathological examinations were conducted at 10 wk after surgery.RESULTS： The PVP was 9.15± 0.58 cmH2O before ligation, and increased to 17.32 ±0.63 cmH2O 2 wk after PVL. By repeat measurement of the PVP in each rat, it was shown to remain elevated for 10 wk. There were no significant differences in the pressure measurements at 2 wk, 6 wk and 10 wk. Varices were found mainly in the mesenteric vein 2 wk after PVL, which were more obvious later, while these manifestations were similar at week 6 and week 10. Portal venography demonstrated the varices and collaterals. There was no significant change in liver pathology. The volume of the spleen was enlarged 2-fold after ligation, and the sinus of the spleen was enlarged due to congestion. Significant sinus endothelial cell proliferation was observed, but no evidence of hypersplenia was found on hemogram and biochemical examination.CONCLUSION： These findings suggest that a satisfactory prehepatic PHT rat model can be obtained by partial ligation of the portal vein, and this PHT rat model was stable for at least 10 wk.展开更多
A kernel-based discriminant analysis method called kernel direct discriminant analysis is employed, which combines the merit of direct linear discriminant analysis with that of kernel trick. In order to demonstrate it...A kernel-based discriminant analysis method called kernel direct discriminant analysis is employed, which combines the merit of direct linear discriminant analysis with that of kernel trick. In order to demonstrate its better robustness to the complex and nonlinear variations of real face images, such as illumination, facial expression, scale and pose variations, experiments are carried out on the Olivetti Research Laboratory, Yale and self-built face databases. The results indicate that in contrast to kernel principal component analysis and kernel linear discriminant analysis, the method can achieve lower （7%） error rate using only a very small set of features. Furthermore, a new corrected kernel model is proposed to improve the recognition performance. Experimental results confirm its superiority （1% in terms of recognition rate） to other polynomial kernel models.展开更多
This paper presents the construction of a pneumatic active suspension system for a one-wheel car model using fuzzy reasoning and a disturbance observer. The one-wheel car model can be approximately described as a nonl...This paper presents the construction of a pneumatic active suspension system for a one-wheel car model using fuzzy reasoning and a disturbance observer. The one-wheel car model can be approximately described as a nonlinear two degrees of freedom system subject to excitation from a road profile. The active control is composed of fuzzy and disturbance controls, and the active control force is constructed by actuating a pneumatic actuator. A phase lead-lag compensator is inserted to counter the performance degradation due to the delay of the pneumatic actuator. The experimental result indicates that the proposed active suspension improves much the vibration suppression of the car model.展开更多
A flow stress equation was proposed to compute the roll force in the finishing stands of an actual rod mill where the strain rate and the temperature of the material range from 100 to 400 s-1 and from 900 to 1050 ℃,r...A flow stress equation was proposed to compute the roll force in the finishing stands of an actual rod mill where the strain rate and the temperature of the material range from 100 to 400 s-1 and from 900 to 1050 ℃,respectively.The underlying idea is to modify the Shida model and Misaka model,which provide flow stress equations（constitutive equations） frequently used to depict deformation behavior of high temperature material at different strain rates.The modified model was coupled with finite element method to compute the roll force during four-pass continuous rod rolling,where strain rates are in the range of 100-400 s-1 at high temperatures（900-1050 ℃）.The roll forces and the surface temperatures of the material at each stand were measured,and the measured data were compared with the computed values.Results reveal that the Misaka model is better than the Shida model for high temperatures and intermediate strain rates.The roll force error was-5.7 % when the Misaka model was used at 900 ℃.However,the error increased by-15.2% at 1050 ℃.When the modified Misaka model was used,the error was reduced to 1.8% on average.It can consequently be deduced that the modified Misaka model can be used to depict the deformation resistance behavior in intermediate ranges of strain rate and high temperature ranges in continuous rod rolling process.展开更多
基金The National Natural Science Foundation of Chin(No.51305208)
文摘In order to investigate the material properties ofperiodontal ligament （ PDL） in different locations, the nanoindentation method is used to survey the elastic modulus of the PDL at different levels. Cadaveric specimens of human mandibular canine were obtained from 4 adult donors, 16 transverse specimens were made from the sections of cervical margin, midroot and apex using the slow cutting machine. The prepared specimens were tested in different sections （along the longitudinal direction） and different areas （in the circumferential direction）. According to the Oliver-Phair theory, the mean values of elastic modulus were calculated foreach area and the differences among them were compared. In the midroot section, the average elastic modulus is ranging from 0. 11 to 0. 23 MPa, the changing range of the cervical margin and apex are from 0. 21 to 0. 53 MPa and 0. 44 to0.62 MPa, respectively. Experimental results indicate that the average elastic modulus in the midroot is lower than that in the cervical margin and apex, and relatively small changes occur among them. However, there is a large change to the elastic modulus value in the cicumferential direction for the PDL.
基金Project(2007AA03Z115) supported by the High-Tech Research and Development Program of China
文摘A combined method of selective laser sintering （SLS） and cold isostatic pressing （CIP） was applied to manufacturing metal parts rapidly. Finite element method was used to predict final dimensions and decrease cost. The simulations of CIP of selective laser sintered parts were carried out by Drucker-Prager-Cap constitutive model with ABAQUS computer program. The property of metal powder was measured by CIP experiments. The results show the rubber bag and the friction coefficient have little influence on results of simulations. The parts only have uniform shrinkage and have no obvious distortion in shape. The results of simulations show a good agreement with the experimental results and the calculated results, indicating that the Drucker-Prager-Cap model is an effective model to simulate CIP process. The simulations could give a useful direction to forming process of the CIP of selective laser sintered components. K
文摘Under natural conditions, the use of vapor pressure deficit between mesophyll cell surface and ambient air ( VPD s ) instead of atmospheric humidity factors in some stomatal models may markedly promote the applicability of stomatal models. It has been pointed out from theoretical analysis that the expression of the responses of stomatal conductance to VPD s is equivalent to the expression of responses of stomatal conductance to water loss of transpiration in stomatal models.
文摘A novel, highly linear sampling switch suitable for low-voltage operation is proposed. This switch not only eliminates the nonlinearity introduced by gate-source voltage variation, but also reduces the nonlinearity resuiting from threshold voltage variation, which has not been accomplished in earlier low-voltage sampling switches. This is achieved by adopting a replica transistor with the same threshold voltage as the sampling transistor. The effectiveness of this technique is demonstrated by a prototype design of a sampling switch in 0. 35μm. The proposed sampling switch achieves a spurious free dynamic range of 111dB for a 0. 2MHz, 1.2Vp-p input signal, sampled at a rate of 2MS/s,about 18dB over the Bootstrapped switch. Also, the on-resistance variation is reduced by 90%. This method is especially useful for low-voltage, high resolution ADCs, which is a hot topic today.
基金Project (No. 2004CB217901) supported by the National Basic Re-search Program (973) of China
文摘Operational reliability evaluation theory reflects real-time reliability level of power system. The component failure rate varies with operating conditions. The impact of real-time operating conditions such as ambient temperature and transformer MVA (megavolt-ampere) loading on transformer insulation life is studied in this paper. The formula of transformer failure rate based on the winding hottest-spot temperature (HST) is given. Thus the real-time reliability model of transformer based on oper- ating conditions is presented. The work is illustrated using the 1979 IEEE Reliability Test System. The changes of operating conditions are simulated by using hourly load curve and temperature curve, so the curves of real-time reliability indices are ob- tained by using operational reliability evaluation.
基金This work has been financially supported by Ministry of Science and Higher Education in Poland as a part of the Project No.0513/SBAD.
文摘The two-stage gas boriding in N_(2)−H_(2)−BCl_(3)atmosphere was applied to producing a two-zoned borided layer on Nisil-alloy.The process was carried out at 910℃ for 2 h.The microstructure consisted of two zones differing in their phase composition.The outer layer contained only a mixture of nickel borides(Ni_(2)B,Ni_(3)B)only.The inner zone contained additionally nickel silicides(Ni_(2)Si,Ni_(3)Si)occurring together with nickel borides.The aim of this study was to determine the presence of nickel silicides on the mechanical properties of the borided layer produced on Ni-based alloy.The hardness and elastic modulus were measured using the nanoindenter with a Berkovich diamond tip under a load of 50 mN.The average values of indentation hardness(HI)and indentation elastic modulus(E_(I))obtained in the outer zone were respectively(16.32±1.03)GPa and(232±16.15)GPa.The presence of nickel silicides in the inner zone reduced the indentation hardness(6.8−12.54 GPa)and elastic modulus(111.79−153.99 GPa).The fracture toughness of the boride layers was investigated using a Vickers microindentation under a load of 0.981 N.It was confirmed that the presence of nickel silicides caused an increase in brittleness(by about 40%)of the gas-borided layer.
基金Project(50908234)supported by the National Natural Science Foundation of China
文摘As a frequently-used roadbed filler,soil-rock mixture is often in the environment of freeze-thaw cycles and different confining pressures.In order to study the freeze-thaw damage mechanism of elastic modulus of soil-rock mixtures at different confining pressures,the concept of meso-interfacial freeze-thaw damage coefficient is put forward and the meso-interfacial damage phenomenon of soil-rock mixtures caused by the freeze-thaw cycle environment is concerned;a double-inclusion embedded model for elastic modulus of soil-rock mixtures in freezing-thawing cycle is proposed.A large triaxial test was performed and the influences of confining pressure and experimental factors on elastic modulus of soil-rock mixtures were obtained,and then the accuracy of the double-inclusion embedded model to predict the elastic modulus of soil-rock mixtures in freezing-thawing cycle is verified.Experiment results showed that as to soil-rock mixtures,with the increase of confining pressure,the elastic modulus increases approximately linearly.The most crucial factors to affect the elastic modulus are rock content and compaction degree at the same confining pressure;the elastic modulus increases with the increase of rock content and compactness;as the number of freeze-thaw cycles increases,the freeze-thaw damage coefficient of meso-structural interface and the elastic modulus decrease.
基金supported by the National Natural Science Foundation of China(Nos.51104128,51322401,51304201 and 51204159)Jiangsu Province Prospective industry-UniversityResearch Cooperation Research Program of China(No.BY2012085)+2 种基金Doctor Station Fund of China(No.20120095110013)333 Project Program of Jiangsu Province of China"Blue Project" Program of Jiangsu Province of China
文摘The uniaxial compression tests for mudstone specimens are carried out with four different loading rates from room temperature to 400℃ by using the Rock Mechanics Servo-controlled Testing System MTS810 and high temperature furnace MTS652.02.The mechanical properties of mudstone with various loading rates are studied under different temperature conditions.The results show that when temperature increases from room temperature to 400℃ and loading rate is less than 0.03 mm/s,the peak strength of mudstone specimen decreases as loading rate increases,while the various peak strengths show significant differences when loading rate exceeds 0.03 mm/s.At room temperature,the elastic modulus decreases at the first time and then increases with loading rate rising.When the temperature is between200 and 400℃,the elastic modulus presents a decreasing trend with increasing loading rate.With increasing the loading rate,the number of fragments in mudstone becomes larger and even the powder is observed in mudstone with higher loading rate.Under high loading rate,the failure mode of mudstone specimens under different temperatures is mainly conical damage.
基金Supported by the National Natural Science Foundation of China (20976048, 21176072)the Fundamental Research Funds for the Central Universities
文摘Cracking gas compressor is usually a centrifugal compressor. The information on the performance of a centrifugal compressor under all conditions is not available, which restricts the operation optimization for compressor. To solve this problem, two back propagation (BP) neural networks were introduced to model the performance of a compressor by using the data provided by manufacturer. The input data of the model under other conditions should be corrected according to the similarity theory. The method was used to optimize the system of a cracking gas compressor by embedding the compressor performance model into the ASPEN PLUS model of compressor. The result shows that it is an effective method to optimize the compressor system.
基金Supported by Hunan Provincial Natural Science Foundation of China under Grant No.10JJ6010the Key Project Foundation of Hunan Provincial Education Department of China under Grant No.10A095
文摘We study a system consisting of two identical non-interacting single-mode cavity fields coupled to a common vacuum environment and provide general, explicit, and exact solutions to its master equation by means of the characteristic function method. We analyze the entanglement dynamics of two-mode squeezed thermal state in this model and show that its entanglement dynamics is strongly determined by the two-mode squeezing parameter and the purity. In particular, we find that two-mode squeezed thermal state with the squeezing parameter r ≤ -（1/2） In √u is extremely fragile and almost does not survive in a common vacuum environment. We investigate the time evolution of nonlocality for two-mode squeezed thermal state in such an environment. It is found that the evolved state loses its nonlocality in the beginning of the evolution, but after a time, the revival of nonlocality can occur.
文摘Zn-22 Al alloy closed-cell foams were fabricated by melt foaming process using hydride foaming agent. The compressive properties were investigated under quasi-static condition. The structure of the foamed material was analyzed during compression test to reveal the relationship between morphology and compressive behavior. The results show that the stress-strain behavior is typical of closed-cell metal foams and mostly of brittle type. Governing deformation mechanism at plateau stage is identified to be brittle crushing. A substantial increase in compressive strength of Zn-22 Al foams was obtained. The agreement between compressive properties and Gibson-Ashby model was also detected.
基金Project(51974192)supported by the National Natural Science Foundation of ChinaProject(201803D31044)supported by the Program for Key Research Project of Shanxi Province in the Field of Social Development,ChinaProject(201801D121092)supported by the Applied Basic Research Project of Shanxi Province,China。
文摘A step-by-step load was utilized to mimic the load history of the backfill column in the in-situ curing process.The inner damage of the specimen during curing and uniaxial compressive testing was monitored by electrical resistivity and ultrasonic equipment.Results show that:1)Uniaxial compressive strength(UCS)and elastic modulus(EM)of the samples curing under pressure are higher than those of the control samples without pressure,ranging in ratio from 0.5%to 20.2%and 7.1%to 52.3%,respectively,and are influenced by the initial loading age(ILA)and stress strength ratio(SSR).The SSR during curing should not exceed 80%.2)The earlier the ILA is,the higher the total strain becomes.The higher the SSR applies,the larger the total strain gets.The creep strain increases with the increase of SSR and can be described by Burger’s viscoelastic creep model.When SSR is less than 80%,the earlier the ILA is,the smaller the creep strain becomes after the last step-loading.3)The stability of the early age backfill column under pressure can be monitored based on the change of ultrasonic pulse velocity(UPV)and electrical resistivity.
基金Supported by National 10th 5-year Science Research Plan of China,No.2001BA705B10-15
文摘AIM： To study the stability of portal hypertension （PHT） caused by partial ligation of the portal vein ligation （PVL） in a rat model.METHODS： Thirty male adult Wistar rats were divided into two groups： 10 in Group Ⅰ received a sham operation; and 20 in Group Ⅱreceived partial PVL. Portal vein pressure （PVP） was measured at four time periods： before ligation, 2 wk, 6 wk and 10 wk postsurgery. Portal venography, blood sampling and liver and spleen pathological examinations were conducted at 10 wk after surgery.RESULTS： The PVP was 9.15± 0.58 cmH2O before ligation, and increased to 17.32 ±0.63 cmH2O 2 wk after PVL. By repeat measurement of the PVP in each rat, it was shown to remain elevated for 10 wk. There were no significant differences in the pressure measurements at 2 wk, 6 wk and 10 wk. Varices were found mainly in the mesenteric vein 2 wk after PVL, which were more obvious later, while these manifestations were similar at week 6 and week 10. Portal venography demonstrated the varices and collaterals. There was no significant change in liver pathology. The volume of the spleen was enlarged 2-fold after ligation, and the sinus of the spleen was enlarged due to congestion. Significant sinus endothelial cell proliferation was observed, but no evidence of hypersplenia was found on hemogram and biochemical examination.CONCLUSION： These findings suggest that a satisfactory prehepatic PHT rat model can be obtained by partial ligation of the portal vein, and this PHT rat model was stable for at least 10 wk.
文摘A kernel-based discriminant analysis method called kernel direct discriminant analysis is employed, which combines the merit of direct linear discriminant analysis with that of kernel trick. In order to demonstrate its better robustness to the complex and nonlinear variations of real face images, such as illumination, facial expression, scale and pose variations, experiments are carried out on the Olivetti Research Laboratory, Yale and self-built face databases. The results indicate that in contrast to kernel principal component analysis and kernel linear discriminant analysis, the method can achieve lower （7%） error rate using only a very small set of features. Furthermore, a new corrected kernel model is proposed to improve the recognition performance. Experimental results confirm its superiority （1% in terms of recognition rate） to other polynomial kernel models.
文摘This paper presents the construction of a pneumatic active suspension system for a one-wheel car model using fuzzy reasoning and a disturbance observer. The one-wheel car model can be approximately described as a nonlinear two degrees of freedom system subject to excitation from a road profile. The active control is composed of fuzzy and disturbance controls, and the active control force is constructed by actuating a pneumatic actuator. A phase lead-lag compensator is inserted to counter the performance degradation due to the delay of the pneumatic actuator. The experimental result indicates that the proposed active suspension improves much the vibration suppression of the car model.
基金supported by the Dong-A University research fund
文摘A flow stress equation was proposed to compute the roll force in the finishing stands of an actual rod mill where the strain rate and the temperature of the material range from 100 to 400 s-1 and from 900 to 1050 ℃,respectively.The underlying idea is to modify the Shida model and Misaka model,which provide flow stress equations（constitutive equations） frequently used to depict deformation behavior of high temperature material at different strain rates.The modified model was coupled with finite element method to compute the roll force during four-pass continuous rod rolling,where strain rates are in the range of 100-400 s-1 at high temperatures（900-1050 ℃）.The roll forces and the surface temperatures of the material at each stand were measured,and the measured data were compared with the computed values.Results reveal that the Misaka model is better than the Shida model for high temperatures and intermediate strain rates.The roll force error was-5.7 % when the Misaka model was used at 900 ℃.However,the error increased by-15.2% at 1050 ℃.When the modified Misaka model was used,the error was reduced to 1.8% on average.It can consequently be deduced that the modified Misaka model can be used to depict the deformation resistance behavior in intermediate ranges of strain rate and high temperature ranges in continuous rod rolling process.
