The hydrodynamic characteristics of a rigid, single, circular cylinder in a three dimensional, incompressible, uniform cross flow were calculated using the large-eddy simulation method of CFX5. Solutions to the three ...The hydrodynamic characteristics of a rigid, single, circular cylinder in a three dimensional, incompressible, uniform cross flow were calculated using the large-eddy simulation method of CFX5. Solutions to the three dimensional N-S equations were obtained by the finite volume method. The focus of this numerical simulation was to research the characteristics of pressure distribution （drag and litt forces） and vortex tubes at high Reynolds numbers. The results of the calculations showed that the forces at every section in the spanwise direction of the cylinder were symmetrical about the middle section and smaller than the forces calculated in two dimensional cases. Moreover, the flow around the cylinder obviously presents three dimensional characteristics.展开更多
To investigate the flow behaviors of different size particles in hydrocyclone,a designed process was numerically simulated by the transient solver,where the quartz particles possessing a size distribution were injecte...To investigate the flow behaviors of different size particles in hydrocyclone,a designed process was numerically simulated by the transient solver,where the quartz particles possessing a size distribution were injected into a 100 mm diameter hydrocyclone with the steady water field and air core inside.A lab experimental work has validated the chosen models in simulation by comparing the classification efficiency results.The simulated process shows that the 25 μm quartz particles,close to the cut size,need much more time than the finer and coarser particles to reach the steady flow rate on the outlets of hydrocyclone.For the particles in the inner swirl,with the quartz size increasing from 5 to 25 μm,the particles take more time to enter the vortex finder.The 25 μm quartz particles move outward in the radial direction when they go up to the vortex finder,which is contrary to the quartz particles of 5 μm and 15 μm as they are closely surrounding the air core.The studies reveal that the flow behaviors of particles inside the hydrocyclone depend on the particle size.展开更多
A numerical analysis of the log-law behavior for the turbulent boundary layer of a wall-bounded flow is performed over a flat plate immersed in three nanofluids(Zn O-water,SiO_(2)-water,TiO_(2)-water).Numerical simula...A numerical analysis of the log-law behavior for the turbulent boundary layer of a wall-bounded flow is performed over a flat plate immersed in three nanofluids(Zn O-water,SiO_(2)-water,TiO_(2)-water).Numerical simulations using CFD code are employed to investigate the boundary layer and the hydrodynamic flow.To validate the current numerical model,measurement points from published works were used,and the compared results were in good compliance.Simulations were carried out for the velocity series of 0.04,0.4 and 4 m/s and nanoparticle concentrations0.1% and 5%.The influence of nanoparticles’ concentration on velocity,temperature profiles,wall shear stress,and turbulent intensity was investigated.The obtained results showed that the viscous sub-layer,the buffer layer,and the loglaw layer along the potential-flow layer could be analyzed based on their curving quality in the regions which have just a single wall distance.It was seen that the viscous sub-layer is the biggest area in comparison with other areas.Alternatively,the section where the temperature changes considerably correspond to the thermal boundary layer’s thickness goes a downward trend when the velocity decreases.The thermal boundary layer gets deep away from the leading edge.However,a rise in the volume fraction of nanoparticles indicated a minor impact on the shear stress developed in the wall.In all cases,the thickness of the boundary layer undergoes a downward trend as the velocity increases,whereas increasing the nanoparticle concentrations would enhance the thickness.More precisely,the log layer is closed with log law,and it is minimal between Y^(+)=50 and Y^(+)=95.The temperature for nanoparticle concentration φ=5%is higher than that for φ=0.1%,in boundary layers,for all studied nanofluids.However,it is established that the behavior is inverted from the value of Y^(+)=1 and the temperature for φ =0.1% is more important than the case of φ =5%.For turbulence intensity peak,this peak exists at Y^(+)=100 for v=4 m/s,Y^(+)=10 for v=0.4 m/s and Y^(+)=8 for v=0.04 m/s.展开更多
It’s very complicated to calculate and analyze the wave and current loads on naval architectures since the sea condition is uncertain and complicated and the determinants vary from different form types and dimensions...It’s very complicated to calculate and analyze the wave and current loads on naval architectures since the sea condition is uncertain and complicated and the determinants vary from different form types and dimensions. For calculating the wave and current loads on upright small-long-size pipe, the Morrison equation is practical and applied. Jacket platform is a kind of offshore space frame structure comprised of lots of poles that are circular cylinders with small diameter and in the oblique status relative to seabed. In this paper, based on Morrison equation, the specific method and procedure calculating the wave and current loads on launching jacket are given and applied on a typical launching jacket. The instance shows that the method and procedure are convenient and make the calculation and analysis in good agreement with actual launching.展开更多
Large eddy simulations (LES) of mixing process in a stirred tank of 0.476m diameter with a 3-narrow blade hydrofoil CBY impeller were reported. The turbulent flow field and mixing time were calculated using LES with S...Large eddy simulations (LES) of mixing process in a stirred tank of 0.476m diameter with a 3-narrow blade hydrofoil CBY impeller were reported. The turbulent flow field and mixing time were calculated using LES with Sma-gorinsky-Lilly subgrid scale model. The impeller rotation was modeled using the sliding mesh technique. Better agree-ment of power demand and mixing time was obtained between the experimental and the LES prediction than that by the traditional Reynolds-averaged Navier-Stokes (RANS) approach. The curve of tracer response predicted by LES was in good agreement with the experimental. The results show that LES is a reliable tool to investigate the unsteady and quasi-periodic behavior of the turbulent flow in stirred tanks.展开更多
A mathematical model of podded propulsors was established in order to investigate the influence of fins. The hydrodynamic performance of podded propulsors with and without fins was calculated, with interactions betwee...A mathematical model of podded propulsors was established in order to investigate the influence of fins. The hydrodynamic performance of podded propulsors with and without fins was calculated, with interactions between propellers and pods and fins derived by iterative calculation. The differential equation based on velocity potential was adopted and hyperboloidal panels were used to avoid gaps between surface panels. The Newton-Raphson iterative procedure was used on the trailing edge to meet the pressure Kutta condition. The velocity distribution was calculated with the Yanagizawa method to eliminate the singularity caused by use of the numerical differential. Comparisons of the performance of podded propulsors with different fins showed that the thrust of propeller in a podded propulsor with fins is greater. The resistance of the pod is also reduced because of the thrust of the fin. The hydrodynamic performance of a podded propulsor with two fins is found to be best, the performance of a podded propulsor with one fin is not as good as two fins, and the performance of the common type is the worst.展开更多
The characteristics of the fluidic flowmeter,which is a combination of impinged concave wall and bistable fluid amplifier,is investigated by experimental studies and numerical simulations. The numerical approaches are...The characteristics of the fluidic flowmeter,which is a combination of impinged concave wall and bistable fluid amplifier,is investigated by experimental studies and numerical simulations. The numerical approaches are utilized to examine the time dependent flow field and pressure field inside the proposed flowmeter. The effect of varying structural parameters on flow characteristics of the proposed fluidic flowmeter is investigated by computational simulations for the optimization. Both the simulation and experimental results disclose that the hydrodynamic vibration,with the same intensity,frequency and 180° phase shift,occurs at axisymmetric points in the feedback channel of the fluidic flowmeter. Using the structural combination of impinged concave wall and bistable fluid amplifier and differential signal processing technique,a novel fluidic flowmeter with excellent immunity and improved sensibility is developed.展开更多
A new type jet, the oscillating & deflecting jet, is put forward and its oscillating and deflecting characteristics are investigated. The nozzle of the self-oscillating & deflecting water jet consists of an up...A new type jet, the oscillating & deflecting jet, is put forward and its oscillating and deflecting characteristics are investigated. The nozzle of the self-oscillating & deflecting water jet consists of an upstream nozzle, a downstream nozzle, an oscillating chamber and two switches. It is experimentally shown that the deflective angle may reach 9.53 degree. The generated pressure fluctuation is very regular and the jet can efficiently increase the ability for breaking and cutting by eliminating the water cushion effect associated with a continuous jet.展开更多
To solve nutrient flux and budget among waters with distinct salinity difference for water-salt- nutrient budget, a traditional method is to build a stoichiometrically linked steady state model. However, the tradition...To solve nutrient flux and budget among waters with distinct salinity difference for water-salt- nutrient budget, a traditional method is to build a stoichiometrically linked steady state model. However, the traditional way cannot cope appropriately with those without distinct salinity difference that parallel to coastline or in a complex current system, as the results would be highly affected by box division in time and space, such as the Changjiang （Yangtze） River estuary （CRE） and adjacent waters （30.75°-31.75°N, 122°10′-123°20′E）. Therefore, we developed a hydrodynamic box model based on the traditional way and the regional oceanic modeling system model （ROMS）. Using data from four cruises in 2005, horizontal, vertical and boundary nutrient fluxes were calculated in the hydrodynamic box model, in which flux fields and the major controlling factors were studied. Results show that the nutrient flux varied greatly in season and space. Water flux outweighs the nutrient concentration in horizontal flux, and upwelling flux outweighs upward diffusion flux in vertical direction （upwelling flux and upward diffusion flux regions overlap largely all the year）. Vertical flux in spring and summer are much greater than that in autumn and winter. The maximum vertical flux for DIP （dissolved inorganic phosphate） occurs in summer. Additional to the fluxes of the ChanNiang River discharge, coastal currents, the Taiwan Warm Current, and the upwelling, nutrient flux inflow from the southern Yellow Sea and outflow southward are found crucial to nutrient budgets of the study area. Horizontal nutrient flux is controlled by physical dilution and confined to coastal waters with a little into the open seas. The study area acts as a conveyer transferring nutrients from the Yellow Sea to the East China Sea in the whole year. In addition, vertical nutrient flux in spring and summer is a main source of DIP. Therefore, the hydrodynamic ROMS-based box model is superior to the traditional one in estimating nutrient fluxes in a complicated hydrodynamic current system and provides a modified box model approach to material flux research.展开更多
Nowadays, Autonomous Underwater Vehicles(AUVs) are frequently used for exploring the oceans. The hydrodynamics of AUVs moving in the vicinity of the water surface are significantly different at higher depths. In this ...Nowadays, Autonomous Underwater Vehicles(AUVs) are frequently used for exploring the oceans. The hydrodynamics of AUVs moving in the vicinity of the water surface are significantly different at higher depths. In this paper, the hydrodynamic coefficients of an AUV in non-dimensional depths of 0.75, 1, 1.5, 2, and 4D are obtained for movement close to the free-surface. Reynolds Averaged Navier Stokes Equations(RANS) are discretized using the finite volume approach and the water-surface effects modeled using the Volume of Fraction(VOF) method. As the operating speeds of AUVs are usually low, the boundary layer over them is not fully laminar or fully turbulent, so the effect of boundary layer transition from laminar to turbulent flow was considered in the simulations. Two different turbulence/transition models were used: 1) a full-turbulence model, the k-ε model, and 2) a turbulence/transition model, Menter's Transition-SST model. The results show that the Menter's Transition-SST model has a better consistency with experimental results. In addition, the wave-making effects of these bodies are studied at different immersion depths in the sea-surface vicinity or at finite depths. It is observed that the relevant pitch moments and lift coefficients are non-zero for these axi-symmetric bodies when they move close to the sea-surface. This is not expected for greater depths.展开更多
Abstract： The Wenchuan earthquake generated strong surface disturbances and triggered a large number of loose deposits, resulting in the disaster- prone environment with special watershed hydrological characteristics...Abstract： The Wenchuan earthquake generated strong surface disturbances and triggered a large number of loose deposits, resulting in the disaster- prone environment with special watershed hydrological characteristics. This paper was to propose a debris flow formation process and explore the permeability characteristics and critical hydrodynamic conditions of the loose deposits triggered by the earthquake. The Guo Juanyan gully （31005＇27＂ N to 31005＇46＂ N, 103036＇58＂ E to 103037＇09＂ E） in Du Jiangyan City, located in the meizoseismal areas of the Wenchuan earthquake, was chosen as the study area and the disaster-prone environment was analyzed. The formation process of the debris flow was first proposed using a stability analysis, and then, the permeability characteristics of loose deposits were determined via in situ permeability experiments. Finally, the critical 1 h rainfall was simulated through a distributed hydrological model and verified by field observations. The formation process of debris flow could be divided into three stages based on the relationship between the hydrodynamic force and loose deposit resistance. The critical 1 h rainfall amounts under three antecedent moisture conditions （I-dry, Ⅱ-normal and Ⅲ-wet） were 52 mm/h, 43 mm/h and 34 mm/h, respectively. This study proposed a debris flow formation process in the meizoseismal areas of the Wenchuan earthquake based on the stability analysis and defined the rainfall threshold for debris flow early warning at the local level, which is significant for debris flow mitigation and risk management.展开更多
The flow behavior of pressure-driven water infiltration through graphene-based slit nanopores has been studied by molecular simulation.The simulated flow rate is close to the experimental values,which demonstrates the...The flow behavior of pressure-driven water infiltration through graphene-based slit nanopores has been studied by molecular simulation.The simulated flow rate is close to the experimental values,which demonstrates the reasonability of simulation results.Water molecules can spontaneously infiltrate into the nanopores,but an external driving force is generally required to pass through the whole pores.The exit of nanopore has a large obstruction on the water effusion.The flow velocity within the graphene nanochannels does not display monotonous dependence upon the pore width,indicating that the flow is related to the microscopic structures of water confined in the nanopores.Extensive structures of confined water are characterized in order to understand the flow behavior.This simulation improves the understanding of graphene-based nanofluidics,which helps in developing a new type of membrane separation technique.展开更多
As a high gravity(HIGEE)unit,the rotating packed bed(RPB)uses centrifugal force to intensify mass transfer.Zigzag rotating bed(RZB)is a new type of HIGEE unit.The rotor of RZB consists of stationary discs and rotating...As a high gravity(HIGEE)unit,the rotating packed bed(RPB)uses centrifugal force to intensify mass transfer.Zigzag rotating bed(RZB)is a new type of HIGEE unit.The rotor of RZB consists of stationary discs and rotating discs,forming zigzag channels for liquid-gas flow and mass transfer.As in RPBs,some hydrodynamic behavior in RZB is interesting but no satisfactory explanation.In this study,the experiments were carried on in a RZB unit with a rotor of 600 mm in diameter using air-water system.The gas pressure drop and power consumption were measured with two types of rotating baffle for RZB rotors,one with perforations and another with shutter openings. The circumferential velocities of gas were measured with a five-hole Pitot probe.The pressure drop decreased rapidly when the liquid was introduced to the rotor,because the circumferential velocity of the liquid droplets was lower than that of the gas,reducing the circumferential velocity of gas and the centrifugal pressure drop.The power consumption decreased first when the gas entered the RZB rotor,because the gas with higher circumferential velocity facilitates the rotation of baffles.展开更多
In this study, we used the Navy’s Generalized Digital Environmental Model (GDEM) climatological temperature and salinity data on a 0.5°×0.5° grid to investigate the seasonal variabilities of the southw...In this study, we used the Navy’s Generalized Digital Environmental Model (GDEM) climatological temperature and salinity data on a 0.5°×0.5° grid to investigate the seasonal variabilities of the southwest Philippines Sea (0.5°–9°N, 123.5°–136.5°) thermohaline structure and circulation. The GDEM for the area was built up on historical (1930–1997) temperature and salinity profiles. A three-dimensional estimate of the absolute geostrophic velocity field on isopycnal surface was obtained from the GDEM temperature and salinity fields using the P-vector method. The seasonal variabilities of the thermohaline structure and currents (obtained from the inverse method) such as the Mindanao Current, Mindanao Undercurrent, North Equatorial Counter Current, New Guinea Coastal Undercurrent, and dual-eddies (cyclinic Mindanao Eddy and anticyclonic Halmahera Eddy) are identified.展开更多
Because of the complication of turbulence＇s mechanism and law as well as the jet pressure in nozzle is difficult to test by experiment, five turbulent models were applied to numerically simulate the turbulent flow fi...Because of the complication of turbulence＇s mechanism and law as well as the jet pressure in nozzle is difficult to test by experiment, five turbulent models were applied to numerically simulate the turbulent flow field in convergent-divergent nozzle. Theory analysis and experiment results of mass flow rates conclude that the RNG k-ε model is the most suitable model. The pressure distribution in the convergent-divergent nozzle was revealed by computational fluid dynamic （CFD） simulating on the turbulent flow field under different pressure conditions. The growing conditions of cavitation bubbles were shown; meanwhile, the phenomena in the experiment could be explained. The differential pres- sure between the upstream and downstream in nozzle throat section can improve the cavitating effect of cavitation water jet.展开更多
The land surface processes of the Noah-MP and Noah models are evaluated over four typical landscapes in the Haihe River Basin(HRB) using in-situ observations. The simulated soil temperature and moisture in the two lan...The land surface processes of the Noah-MP and Noah models are evaluated over four typical landscapes in the Haihe River Basin(HRB) using in-situ observations. The simulated soil temperature and moisture in the two land surface models(LSMs) is consistent with the observation, especially in the rainy season. The models reproduce the mean values and seasonality of the energy fluxes of the croplands, despite the obvious underestimated total evaporation. Noah shows the lower deep soil temperature. The net radiation is well simulated for the diurnal time scale. The daytime latent heat fluxes are always underestimated, while the sensible heat fluxes are overestimated to some degree. Compared with Noah, Noah-MP has improved daily average soil heat flux with diurnal variations. Generally, Noah-MP performs fairly well for different landscapes of the HRB. The simulated cold bias in soil temperature is possibly linked with the parameterized partition of the energy into surface fluxes. Thus, further improvement of these LSMs remains a major challenge.展开更多
Applications of computational fluid dynamic(CFD) to the maritime industry continue to grow with the increasing development of computers.Numerical approaches have evolved to a level of accuracy which allows them to be ...Applications of computational fluid dynamic(CFD) to the maritime industry continue to grow with the increasing development of computers.Numerical approaches have evolved to a level of accuracy which allows them to be applied for hydrodynamic computations in industry areas.Hydrodynamic tests,especially planar-motion-mechanism(PMM) tests are simulated by CFD software-FLUENT,and all of the corresponding hydrodynamic coefficients are obtained,which satisfy the need of establishing the simulation system to evaluate maneuverability of vehicles during the autonomous underwater vehicle scheme design stage.The established simulation system performed well in tests.展开更多
Liquid sloshing is a type of free surface flow inside a partially filled water tank.Sloshing exerts a significant effect on the safety of liquid transport systems;in particular,it may cause large hydrodynamic loads wh...Liquid sloshing is a type of free surface flow inside a partially filled water tank.Sloshing exerts a significant effect on the safety of liquid transport systems;in particular,it may cause large hydrodynamic loads when the frequency of the tank motion is close to the natural frequency of the tank.Perforated plates have recently been used to suppress the violent movement of liquids in a sloshing tank at resonant conditions.In this study,a numerical model based on OpenF OAM(Open Source Field Operation and Manipulation),an open source computed fluid dynamic code,is used to investigate resonant sloshing in a swaying tank with a submerged horizontal perforated plate.The numerical results of the free surface elevations are first verified using experimental data,and then the flow characteristics around the perforated plate and the fluid velocity distribution in the entire tank are examined using numerical examples.The results clearly show differences in sloshing motions under first-order and third-order resonant frequencies.This study provides a better understanding of the energy dissipation mechanism of a horizontal perforated plate in a swaying tank.展开更多
文摘The hydrodynamic characteristics of a rigid, single, circular cylinder in a three dimensional, incompressible, uniform cross flow were calculated using the large-eddy simulation method of CFX5. Solutions to the three dimensional N-S equations were obtained by the finite volume method. The focus of this numerical simulation was to research the characteristics of pressure distribution （drag and litt forces） and vortex tubes at high Reynolds numbers. The results of the calculations showed that the forces at every section in the spanwise direction of the cylinder were symmetrical about the middle section and smaller than the forces calculated in two dimensional cases. Moreover, the flow around the cylinder obviously presents three dimensional characteristics.
基金Projects(2006BAB11B07,2007BAB15B01)supported by the National Science&Technology Pillar Program during the Eleventh Five-year Plan Period,ChinaProject(2011BAB05B01)supported by the National Science&Technology Pillar Program during the Twelfth Five-year Plan Period,China
文摘To investigate the flow behaviors of different size particles in hydrocyclone,a designed process was numerically simulated by the transient solver,where the quartz particles possessing a size distribution were injected into a 100 mm diameter hydrocyclone with the steady water field and air core inside.A lab experimental work has validated the chosen models in simulation by comparing the classification efficiency results.The simulated process shows that the 25 μm quartz particles,close to the cut size,need much more time than the finer and coarser particles to reach the steady flow rate on the outlets of hydrocyclone.For the particles in the inner swirl,with the quartz size increasing from 5 to 25 μm,the particles take more time to enter the vortex finder.The 25 μm quartz particles move outward in the radial direction when they go up to the vortex finder,which is contrary to the quartz particles of 5 μm and 15 μm as they are closely surrounding the air core.The studies reveal that the flow behaviors of particles inside the hydrocyclone depend on the particle size.
基金support he received through General Research Project under the grant number (R.G.P.2/138/42)。
文摘A numerical analysis of the log-law behavior for the turbulent boundary layer of a wall-bounded flow is performed over a flat plate immersed in three nanofluids(Zn O-water,SiO_(2)-water,TiO_(2)-water).Numerical simulations using CFD code are employed to investigate the boundary layer and the hydrodynamic flow.To validate the current numerical model,measurement points from published works were used,and the compared results were in good compliance.Simulations were carried out for the velocity series of 0.04,0.4 and 4 m/s and nanoparticle concentrations0.1% and 5%.The influence of nanoparticles’ concentration on velocity,temperature profiles,wall shear stress,and turbulent intensity was investigated.The obtained results showed that the viscous sub-layer,the buffer layer,and the loglaw layer along the potential-flow layer could be analyzed based on their curving quality in the regions which have just a single wall distance.It was seen that the viscous sub-layer is the biggest area in comparison with other areas.Alternatively,the section where the temperature changes considerably correspond to the thermal boundary layer’s thickness goes a downward trend when the velocity decreases.The thermal boundary layer gets deep away from the leading edge.However,a rise in the volume fraction of nanoparticles indicated a minor impact on the shear stress developed in the wall.In all cases,the thickness of the boundary layer undergoes a downward trend as the velocity increases,whereas increasing the nanoparticle concentrations would enhance the thickness.More precisely,the log layer is closed with log law,and it is minimal between Y^(+)=50 and Y^(+)=95.The temperature for nanoparticle concentration φ=5%is higher than that for φ=0.1%,in boundary layers,for all studied nanofluids.However,it is established that the behavior is inverted from the value of Y^(+)=1 and the temperature for φ =0.1% is more important than the case of φ =5%.For turbulence intensity peak,this peak exists at Y^(+)=100 for v=4 m/s,Y^(+)=10 for v=0.4 m/s and Y^(+)=8 for v=0.04 m/s.
基金Supported by Item of Doctor Subject of Colleges and University (No.2000014125) and the Education Office of Liaoning Province (No.05l091).
文摘It’s very complicated to calculate and analyze the wave and current loads on naval architectures since the sea condition is uncertain and complicated and the determinants vary from different form types and dimensions. For calculating the wave and current loads on upright small-long-size pipe, the Morrison equation is practical and applied. Jacket platform is a kind of offshore space frame structure comprised of lots of poles that are circular cylinders with small diameter and in the oblique status relative to seabed. In this paper, based on Morrison equation, the specific method and procedure calculating the wave and current loads on launching jacket are given and applied on a typical launching jacket. The instance shows that the method and procedure are convenient and make the calculation and analysis in good agreement with actual launching.
文摘Large eddy simulations (LES) of mixing process in a stirred tank of 0.476m diameter with a 3-narrow blade hydrofoil CBY impeller were reported. The turbulent flow field and mixing time were calculated using LES with Sma-gorinsky-Lilly subgrid scale model. The impeller rotation was modeled using the sliding mesh technique. Better agree-ment of power demand and mixing time was obtained between the experimental and the LES prediction than that by the traditional Reynolds-averaged Navier-Stokes (RANS) approach. The curve of tracer response predicted by LES was in good agreement with the experimental. The results show that LES is a reliable tool to investigate the unsteady and quasi-periodic behavior of the turbulent flow in stirred tanks.
基金Supported by the National Natural Science Foundation of China under Grant No.10702016
文摘A mathematical model of podded propulsors was established in order to investigate the influence of fins. The hydrodynamic performance of podded propulsors with and without fins was calculated, with interactions between propellers and pods and fins derived by iterative calculation. The differential equation based on velocity potential was adopted and hyperboloidal panels were used to avoid gaps between surface panels. The Newton-Raphson iterative procedure was used on the trailing edge to meet the pressure Kutta condition. The velocity distribution was calculated with the Yanagizawa method to eliminate the singularity caused by use of the numerical differential. Comparisons of the performance of podded propulsors with different fins showed that the thrust of propeller in a podded propulsor with fins is greater. The resistance of the pod is also reduced because of the thrust of the fin. The hydrodynamic performance of a podded propulsor with two fins is found to be best, the performance of a podded propulsor with one fin is not as good as two fins, and the performance of the common type is the worst.
基金Project supported by the National Basic Research Program (973) of China (No.2006CB705400)the National Natural Science Foundation of China (No.50575200)
文摘The characteristics of the fluidic flowmeter,which is a combination of impinged concave wall and bistable fluid amplifier,is investigated by experimental studies and numerical simulations. The numerical approaches are utilized to examine the time dependent flow field and pressure field inside the proposed flowmeter. The effect of varying structural parameters on flow characteristics of the proposed fluidic flowmeter is investigated by computational simulations for the optimization. Both the simulation and experimental results disclose that the hydrodynamic vibration,with the same intensity,frequency and 180° phase shift,occurs at axisymmetric points in the feedback channel of the fluidic flowmeter. Using the structural combination of impinged concave wall and bistable fluid amplifier and differential signal processing technique,a novel fluidic flowmeter with excellent immunity and improved sensibility is developed.
基金Funded by National Natural Science Fund of China(No. 50074035)
文摘A new type jet, the oscillating & deflecting jet, is put forward and its oscillating and deflecting characteristics are investigated. The nozzle of the self-oscillating & deflecting water jet consists of an upstream nozzle, a downstream nozzle, an oscillating chamber and two switches. It is experimentally shown that the deflective angle may reach 9.53 degree. The generated pressure fluctuation is very regular and the jet can efficiently increase the ability for breaking and cutting by eliminating the water cushion effect associated with a continuous jet.
基金Supported by the National Nature Science Foundation of China(Nos.41121064,41276116)the National Basic Research Program of China(973 Program)(No.2010CB428706)
文摘To solve nutrient flux and budget among waters with distinct salinity difference for water-salt- nutrient budget, a traditional method is to build a stoichiometrically linked steady state model. However, the traditional way cannot cope appropriately with those without distinct salinity difference that parallel to coastline or in a complex current system, as the results would be highly affected by box division in time and space, such as the Changjiang （Yangtze） River estuary （CRE） and adjacent waters （30.75°-31.75°N, 122°10′-123°20′E）. Therefore, we developed a hydrodynamic box model based on the traditional way and the regional oceanic modeling system model （ROMS）. Using data from four cruises in 2005, horizontal, vertical and boundary nutrient fluxes were calculated in the hydrodynamic box model, in which flux fields and the major controlling factors were studied. Results show that the nutrient flux varied greatly in season and space. Water flux outweighs the nutrient concentration in horizontal flux, and upwelling flux outweighs upward diffusion flux in vertical direction （upwelling flux and upward diffusion flux regions overlap largely all the year）. Vertical flux in spring and summer are much greater than that in autumn and winter. The maximum vertical flux for DIP （dissolved inorganic phosphate） occurs in summer. Additional to the fluxes of the ChanNiang River discharge, coastal currents, the Taiwan Warm Current, and the upwelling, nutrient flux inflow from the southern Yellow Sea and outflow southward are found crucial to nutrient budgets of the study area. Horizontal nutrient flux is controlled by physical dilution and confined to coastal waters with a little into the open seas. The study area acts as a conveyer transferring nutrients from the Yellow Sea to the East China Sea in the whole year. In addition, vertical nutrient flux in spring and summer is a main source of DIP. Therefore, the hydrodynamic ROMS-based box model is superior to the traditional one in estimating nutrient fluxes in a complicated hydrodynamic current system and provides a modified box model approach to material flux research.
文摘Nowadays, Autonomous Underwater Vehicles(AUVs) are frequently used for exploring the oceans. The hydrodynamics of AUVs moving in the vicinity of the water surface are significantly different at higher depths. In this paper, the hydrodynamic coefficients of an AUV in non-dimensional depths of 0.75, 1, 1.5, 2, and 4D are obtained for movement close to the free-surface. Reynolds Averaged Navier Stokes Equations(RANS) are discretized using the finite volume approach and the water-surface effects modeled using the Volume of Fraction(VOF) method. As the operating speeds of AUVs are usually low, the boundary layer over them is not fully laminar or fully turbulent, so the effect of boundary layer transition from laminar to turbulent flow was considered in the simulations. Two different turbulence/transition models were used: 1) a full-turbulence model, the k-ε model, and 2) a turbulence/transition model, Menter's Transition-SST model. The results show that the Menter's Transition-SST model has a better consistency with experimental results. In addition, the wave-making effects of these bodies are studied at different immersion depths in the sea-surface vicinity or at finite depths. It is observed that the relevant pitch moments and lift coefficients are non-zero for these axi-symmetric bodies when they move close to the sea-surface. This is not expected for greater depths.
基金Financial support was provided by the international cooperation project of the Ministry of Science and Technology (Grant No.2013DFA21720)the Key Laboratory of Mountain Hazards and Earth Surface Processes independent project fundingthe National Natural Science Foundation (Grant No. 41372331)
文摘Abstract： The Wenchuan earthquake generated strong surface disturbances and triggered a large number of loose deposits, resulting in the disaster- prone environment with special watershed hydrological characteristics. This paper was to propose a debris flow formation process and explore the permeability characteristics and critical hydrodynamic conditions of the loose deposits triggered by the earthquake. The Guo Juanyan gully （31005＇27＂ N to 31005＇46＂ N, 103036＇58＂ E to 103037＇09＂ E） in Du Jiangyan City, located in the meizoseismal areas of the Wenchuan earthquake, was chosen as the study area and the disaster-prone environment was analyzed. The formation process of the debris flow was first proposed using a stability analysis, and then, the permeability characteristics of loose deposits were determined via in situ permeability experiments. Finally, the critical 1 h rainfall was simulated through a distributed hydrological model and verified by field observations. The formation process of debris flow could be divided into three stages based on the relationship between the hydrodynamic force and loose deposit resistance. The critical 1 h rainfall amounts under three antecedent moisture conditions （I-dry, Ⅱ-normal and Ⅲ-wet） were 52 mm/h, 43 mm/h and 34 mm/h, respectively. This study proposed a debris flow formation process in the meizoseismal areas of the Wenchuan earthquake based on the stability analysis and defined the rainfall threshold for debris flow early warning at the local level, which is significant for debris flow mitigation and risk management.
基金Supported by the National Natural Science Foundation of China(21376116)A PAPD Project of Jiangsu Higher Education Institution
文摘The flow behavior of pressure-driven water infiltration through graphene-based slit nanopores has been studied by molecular simulation.The simulated flow rate is close to the experimental values,which demonstrates the reasonability of simulation results.Water molecules can spontaneously infiltrate into the nanopores,but an external driving force is generally required to pass through the whole pores.The exit of nanopore has a large obstruction on the water effusion.The flow velocity within the graphene nanochannels does not display monotonous dependence upon the pore width,indicating that the flow is related to the microscopic structures of water confined in the nanopores.Extensive structures of confined water are characterized in order to understand the flow behavior.This simulation improves the understanding of graphene-based nanofluidics,which helps in developing a new type of membrane separation technique.
基金Supported by the Natural Science Foundation of Zhejiang Province（Y406239）
文摘As a high gravity(HIGEE)unit,the rotating packed bed(RPB)uses centrifugal force to intensify mass transfer.Zigzag rotating bed(RZB)is a new type of HIGEE unit.The rotor of RZB consists of stationary discs and rotating discs,forming zigzag channels for liquid-gas flow and mass transfer.As in RPBs,some hydrodynamic behavior in RZB is interesting but no satisfactory explanation.In this study,the experiments were carried on in a RZB unit with a rotor of 600 mm in diameter using air-water system.The gas pressure drop and power consumption were measured with two types of rotating baffle for RZB rotors,one with perforations and another with shutter openings. The circumferential velocities of gas were measured with a five-hole Pitot probe.The pressure drop decreased rapidly when the liquid was introduced to the rotor,because the circumferential velocity of the liquid droplets was lower than that of the gas,reducing the circumferential velocity of gas and the centrifugal pressure drop.The power consumption decreased first when the gas entered the RZB rotor,because the gas with higher circumferential velocity facilitates the rotation of baffles.
文摘In this study, we used the Navy’s Generalized Digital Environmental Model (GDEM) climatological temperature and salinity data on a 0.5°×0.5° grid to investigate the seasonal variabilities of the southwest Philippines Sea (0.5°–9°N, 123.5°–136.5°) thermohaline structure and circulation. The GDEM for the area was built up on historical (1930–1997) temperature and salinity profiles. A three-dimensional estimate of the absolute geostrophic velocity field on isopycnal surface was obtained from the GDEM temperature and salinity fields using the P-vector method. The seasonal variabilities of the thermohaline structure and currents (obtained from the inverse method) such as the Mindanao Current, Mindanao Undercurrent, North Equatorial Counter Current, New Guinea Coastal Undercurrent, and dual-eddies (cyclinic Mindanao Eddy and anticyclonic Halmahera Eddy) are identified.
基金Supported by the National Natural Science Foundation of China (50621403,50604019)Program for New Century Excellent Talents in Univer sity(NCET-06-0767)
文摘Because of the complication of turbulence＇s mechanism and law as well as the jet pressure in nozzle is difficult to test by experiment, five turbulent models were applied to numerically simulate the turbulent flow field in convergent-divergent nozzle. Theory analysis and experiment results of mass flow rates conclude that the RNG k-ε model is the most suitable model. The pressure distribution in the convergent-divergent nozzle was revealed by computational fluid dynamic （CFD） simulating on the turbulent flow field under different pressure conditions. The growing conditions of cavitation bubbles were shown; meanwhile, the phenomena in the experiment could be explained. The differential pres- sure between the upstream and downstream in nozzle throat section can improve the cavitating effect of cavitation water jet.
基金supported by a project of the National Key Research and Development Program of China (Grant No.2016YFA0602501)a project of the National Natural Science Foundation of China (Grant Nos.41630532 and 41575093)
文摘The land surface processes of the Noah-MP and Noah models are evaluated over four typical landscapes in the Haihe River Basin(HRB) using in-situ observations. The simulated soil temperature and moisture in the two land surface models(LSMs) is consistent with the observation, especially in the rainy season. The models reproduce the mean values and seasonality of the energy fluxes of the croplands, despite the obvious underestimated total evaporation. Noah shows the lower deep soil temperature. The net radiation is well simulated for the diurnal time scale. The daytime latent heat fluxes are always underestimated, while the sensible heat fluxes are overestimated to some degree. Compared with Noah, Noah-MP has improved daily average soil heat flux with diurnal variations. Generally, Noah-MP performs fairly well for different landscapes of the HRB. The simulated cold bias in soil temperature is possibly linked with the parameterized partition of the energy into surface fluxes. Thus, further improvement of these LSMs remains a major challenge.
基金Supported by the Open Research Foundation of SKLabAUV,HEU under Grant No.2008003
文摘Applications of computational fluid dynamic(CFD) to the maritime industry continue to grow with the increasing development of computers.Numerical approaches have evolved to a level of accuracy which allows them to be applied for hydrodynamic computations in industry areas.Hydrodynamic tests,especially planar-motion-mechanism(PMM) tests are simulated by CFD software-FLUENT,and all of the corresponding hydrodynamic coefficients are obtained,which satisfy the need of establishing the simulation system to evaluate maneuverability of vehicles during the autonomous underwater vehicle scheme design stage.The established simulation system performed well in tests.
基金supported by the National Natural Science Foundation of China(Nos.51490675,51322903,and 51279224)
文摘Liquid sloshing is a type of free surface flow inside a partially filled water tank.Sloshing exerts a significant effect on the safety of liquid transport systems;in particular,it may cause large hydrodynamic loads when the frequency of the tank motion is close to the natural frequency of the tank.Perforated plates have recently been used to suppress the violent movement of liquids in a sloshing tank at resonant conditions.In this study,a numerical model based on OpenF OAM(Open Source Field Operation and Manipulation),an open source computed fluid dynamic code,is used to investigate resonant sloshing in a swaying tank with a submerged horizontal perforated plate.The numerical results of the free surface elevations are first verified using experimental data,and then the flow characteristics around the perforated plate and the fluid velocity distribution in the entire tank are examined using numerical examples.The results clearly show differences in sloshing motions under first-order and third-order resonant frequencies.This study provides a better understanding of the energy dissipation mechanism of a horizontal perforated plate in a swaying tank.
