Oil-in-water(o/w) emulsions were produced with a membrane emulsification system. The effect of the continuous phase viscosity on the emulsification was studied. The theoretical analyses show that the continuous phase ...Oil-in-water(o/w) emulsions were produced with a membrane emulsification system. The effect of the continuous phase viscosity on the emulsification was studied. The theoretical analyses show that the continuous phase viscosity influences not only the flow field of the continuous phase but also the interfacial tension. The droplet size distribution and disperse phase flux for different continuous phase viscosity were investigated experimentally at constant wall shear stress and constant volume flow rate of the continuous phase respectively.展开更多
A silicone oil emulsion with 60% of solid content was prepared with methyl silicone oil used as the main material by means of the emulsifier-in-oil method.The influence of emulsification conditions on the droplet diam...A silicone oil emulsion with 60% of solid content was prepared with methyl silicone oil used as the main material by means of the emulsifier-in-oil method.The influence of emulsification conditions on the droplet diameter of silicone oil emulsion was discussed.The experimental results showed that the emulsification method,including the quantity of the emulsifier,the time and temperature of emulsification,the emulsifying water dosage,and the stirring speed,had significant impact on the droplet size.The optimal conditions were identified to achieve a smallest droplet diameter of the emulsion at an emulsifier dosage of 6%,an emulsification temperature of 70 ℃,an emulsification time of 30 min,and a stirring speed of 1100 r/min,with water added in two portions at a ratio of 1:1.The high-solid content silicone oil emulsion with a mean droplet diameter of 2.731 μm was prepared under these conditions that could ensure absence of stratification and floating oil under centrifuging at a speed of 3000 r/min for 30 min.展开更多
An investigation was carried out to eliminate the decrease of effluent pH value in carbon filter in O3-biological activated carbon process. The influence factors were examined in a pilot test, and pH was adjusted in t...An investigation was carried out to eliminate the decrease of effluent pH value in carbon filter in O3-biological activated carbon process. The influence factors were examined in a pilot test, and pH was adjusted in the pilot and waterworks. Results show that the carbon filter is an acid-base buffer system and the activated carbon is the key factor. Chemical functional groups on activated carbon surface present acid-base properties to buffer the water but decrease with time, so that effluent pH value decreases. The effects of ozone dosage, CO2 in the carbon filter, and the filter influent quality are negligible. A new method to adjust pH is developed: the activated carbon is first modified by soaking in sodium hydroxide solution to make its pH reach the desired value, and then the pH value of inflow is controlled to certain value by dosing lime in sand filter influent. The method is economical and effective.展开更多
The plates of AA5086 aluminium alloy were joined together by friction stir welding at a fixed rotation speed of 1000 r/min various welding speeds ranging from 63 to 100 mm/min.Corrosion behavior of the parent alloy(PA...The plates of AA5086 aluminium alloy were joined together by friction stir welding at a fixed rotation speed of 1000 r/min various welding speeds ranging from 63 to 100 mm/min.Corrosion behavior of the parent alloy(PA),the heat affected zone(HAZ),and the weld nugget zone(WNZ)of the joints were studied in 3.5%(mass fraction)aerated aqueous Na Cl solution by potentiodynamic polarization and electrochemical impedance spectroscopy(EIS).The corrosion susceptibility of the weldments increases when the welding speed increases to 63 and 100 mm/min.However,the value of corrosion rate in the weldments is lower than that in the PA.Additionally,the corrosion current density increases with increasing the welding speed in the HAZ and the WNZ.On the contrary,the corrosion potential in the WNZ appears more positive than in the HAZ with decreasing the welding speed.The WNZ exhibits higher resistance compared to the HAZ and the PA as the welding speed decreases.The results obtained from the EIS measurements suggest that the weld regions have higher corrosion resistance than the parent alloy.With increasing the welding speed,the distribution and extent of the corroded areas in the WNZ region are lower than those of the HAZ region.In the HAZ region,in addition to the pits in the corroded area,some cracks can be seen around the corroded areas,which confirms that intergranular corrosion is formed in this area.The alkaline localized corrosion and the pitting corrosion are the main corrosion mechanisms in the corroded areas within the weld regions.Crystallographic pits are observed within the weld regions.展开更多
基金Supported by the National Natural Science Foundation of China(No.29506050)and DAAD scholarship
文摘Oil-in-water(o/w) emulsions were produced with a membrane emulsification system. The effect of the continuous phase viscosity on the emulsification was studied. The theoretical analyses show that the continuous phase viscosity influences not only the flow field of the continuous phase but also the interfacial tension. The droplet size distribution and disperse phase flux for different continuous phase viscosity were investigated experimentally at constant wall shear stress and constant volume flow rate of the continuous phase respectively.
文摘A silicone oil emulsion with 60% of solid content was prepared with methyl silicone oil used as the main material by means of the emulsifier-in-oil method.The influence of emulsification conditions on the droplet diameter of silicone oil emulsion was discussed.The experimental results showed that the emulsification method,including the quantity of the emulsifier,the time and temperature of emulsification,the emulsifying water dosage,and the stirring speed,had significant impact on the droplet size.The optimal conditions were identified to achieve a smallest droplet diameter of the emulsion at an emulsifier dosage of 6%,an emulsification temperature of 70 ℃,an emulsification time of 30 min,and a stirring speed of 1100 r/min,with water added in two portions at a ratio of 1:1.The high-solid content silicone oil emulsion with a mean droplet diameter of 2.731 μm was prepared under these conditions that could ensure absence of stratification and floating oil under centrifuging at a speed of 3000 r/min for 30 min.
基金Supported by the National Water Pollution Control and Harnessing Projects (2009ZX07423-003)
文摘An investigation was carried out to eliminate the decrease of effluent pH value in carbon filter in O3-biological activated carbon process. The influence factors were examined in a pilot test, and pH was adjusted in the pilot and waterworks. Results show that the carbon filter is an acid-base buffer system and the activated carbon is the key factor. Chemical functional groups on activated carbon surface present acid-base properties to buffer the water but decrease with time, so that effluent pH value decreases. The effects of ozone dosage, CO2 in the carbon filter, and the filter influent quality are negligible. A new method to adjust pH is developed: the activated carbon is first modified by soaking in sodium hydroxide solution to make its pH reach the desired value, and then the pH value of inflow is controlled to certain value by dosing lime in sand filter influent. The method is economical and effective.
文摘The plates of AA5086 aluminium alloy were joined together by friction stir welding at a fixed rotation speed of 1000 r/min various welding speeds ranging from 63 to 100 mm/min.Corrosion behavior of the parent alloy(PA),the heat affected zone(HAZ),and the weld nugget zone(WNZ)of the joints were studied in 3.5%(mass fraction)aerated aqueous Na Cl solution by potentiodynamic polarization and electrochemical impedance spectroscopy(EIS).The corrosion susceptibility of the weldments increases when the welding speed increases to 63 and 100 mm/min.However,the value of corrosion rate in the weldments is lower than that in the PA.Additionally,the corrosion current density increases with increasing the welding speed in the HAZ and the WNZ.On the contrary,the corrosion potential in the WNZ appears more positive than in the HAZ with decreasing the welding speed.The WNZ exhibits higher resistance compared to the HAZ and the PA as the welding speed decreases.The results obtained from the EIS measurements suggest that the weld regions have higher corrosion resistance than the parent alloy.With increasing the welding speed,the distribution and extent of the corroded areas in the WNZ region are lower than those of the HAZ region.In the HAZ region,in addition to the pits in the corroded area,some cracks can be seen around the corroded areas,which confirms that intergranular corrosion is formed in this area.The alkaline localized corrosion and the pitting corrosion are the main corrosion mechanisms in the corroded areas within the weld regions.Crystallographic pits are observed within the weld regions.
