This paper consists of two parts. (1) For a hollow sphere with sudden temperature changes on its inner and outer surfaces, the hyperbolic heat conduction equation is employed to describe this extreme thermal case and...This paper consists of two parts. (1) For a hollow sphere with sudden temperature changes on its inner and outer surfaces, the hyperbolic heat conduction equation is employed to describe this extreme thermal case and an analytical expression of its temperature distribution is obtained. According to the expression, the non-Fourier heat conduction behavior that will appear in the hollow sphere is studied and some qualitative conditions that will result in distinct non-Fourier behavior in the medium is ultimately attained. (2) A novel experiment to observe non-Fourier heat conduction behavior in porous material (mainly ordinary duplicating paper) heated by a microsecond laser pulse is presented. The conditions for observing distinct non-Fourier heat conduction behavior in the experimental sample agree well with the theoretical results qualitatively.展开更多
The aim of this work is to simulate thermal deformation of tool system and investigate the influence of cutting parameters on it in single-point diamond turning(SPDT) of aluminum alloy. The experiments with various cu...The aim of this work is to simulate thermal deformation of tool system and investigate the influence of cutting parameters on it in single-point diamond turning(SPDT) of aluminum alloy. The experiments with various cutting parameters were conducted. Cutting temperature was measured by FLIR A315 infrared thermal imager. Tool wear was measured by scanning electron microscope(SEM). The numerical model of heat flux considering tool wear generated in cutting zone was established. Then two-step finite element method(FEM) simulations matching the experimental conditions were carried out to simulate the thermal deformation. In addition, the tests of deformation of tool system were performed to verify previous simulation results. And then the influence of cutting parameters on thermal deformation was investigated. The results show that the temperature and thermal deformation from simulations agree well with the results from experiments in the same conditions. The maximum thermal deformation of tool reaches to 7 μm. The average flank wear width and cutting speed are the dominant factors affecting thermal deformation, and the effective way to decrease the thermal deformation of tool is to control the tool wear and the cutting speed.展开更多
The present investigation deals with process analysis of oxy-acetylene flame assisted double pass line heating for varying plate thickness, oxy-acetylene flame as the heat source for multi pass line heating to achieve...The present investigation deals with process analysis of oxy-acetylene flame assisted double pass line heating for varying plate thickness, oxy-acetylene flame as the heat source for multi pass line heating to achieve 3-D bending of plates with varying thicknesses was studied. The oxy-acetylene flame was modeled as the moving heat source in the FEM analysis. The transient thermal histories were predicted taking into account the temperature dependent thermo-mechanical properties. A comparative study between single pass and double pass line heating residual deformation was also carried out. The temperature distribution and residual detbrmations predicted by the numerical model developed in the present work compared fairly well with those of the experimental ones.展开更多
Desulfurization experiments of CuO, γ-Al2O3 and CuO/γ-Al2O3 were made in simulated flue gas by means of thermogravimetric analysis. It is found that reaction activities of CuO supported on γ-Al2O3 could be highly i...Desulfurization experiments of CuO, γ-Al2O3 and CuO/γ-Al2O3 were made in simulated flue gas by means of thermogravimetric analysis. It is found that reaction activities of CuO supported on γ-Al2O3 could be highly improved. Desulfurization kinetics of CuO/γ-Al2O3 was studied in the temperature range of 250 °C-400 °C and SO2 concentration of 0.1%-0.9%. The experimental data were tested and compared with kinetics models of volume reaction model(VRM), grain size model(GSM), random pore model(RPM) and pore-blocking model(PBM). Correlation analysis shows that VRM and RPM models do not fit experimental data well. GSM contradicts with the changes in the physical and chemical properties of Cu O/γ-Al2O3 as the desulfurization proceeds. It is found that PBM is consistent with the change of pore structure of CuO/γ-Al2O3 sorbent during desulfurization process and predicts the conversion-time curves of the sorbent well. Meanwhile, kinetics parameters are obtained and discussed.展开更多
In this work an experimental study combined with an analytical investigation for cooling superheated Carbon Dioxide （CO2） gas were carried out. This work is intended to be part of the super critical Gustav Lorentzen...In this work an experimental study combined with an analytical investigation for cooling superheated Carbon Dioxide （CO2） gas were carried out. This work is intended to be part of the super critical Gustav Lorentzen refrigeration cycle of CO2. Experimental and analytical works concentrated on heat transfer and pressure drop for single phase flow during gas cooling inside tubes filled with porous media. Analytical empirical correlations were formulated for the coefficient of convectional heat transfer and for the pressure drop. A comparison between experimental results and that obtained by developed correlations were carried out, and a comparison between these results and literature published ones were carried out too. The results of this research showed that for cooling process the proposed correlations were proved to be acceptably accurate for pressure drop with difference from experimental results of 2%, while for convective heat transfer the difference from experimental results reached about 3%. More than 90% agreement with literature results was obtained. This work can enhance the calculations of heat flux and pressure drop of gases flow inside porous media filled tubes, and can help in the design procedure of heat exchangers and cooling processes.展开更多
From the viewpoints of environmental conservation and energy efficiency,seawater-source heat pump system(SWHP) to provide district cooling and heating is applied in coastal areas.Based on the system,a heat transfer mo...From the viewpoints of environmental conservation and energy efficiency,seawater-source heat pump system(SWHP) to provide district cooling and heating is applied in coastal areas.Based on the system,a heat transfer model was established for cast heat exchanger(CHE) adopted by SWHP systems.The CHE consists of pipes immersed in the seawater and used for transferring heat between the seawater and the heat exchanger pipes of SWHP system.An experimental study was carried out to test the validity of the model.A program was developed in VB language and the effects of inlet temperature,flow rate of the secondary refrigerant and length of CHE on the results were investigated.The results of the numerical simulation are in consistence with the experiments in both winter and summer conditions.As a result,application of SWHP systems with CHE in coastal areas in China is feasible due to the favorable geographical conditions and environment.展开更多
It is promising to simultaneously develop multiple products through the combined utilization of seawater by solar chimney technology. A small scale experimental system was set up. The collector temperature, the seawat...It is promising to simultaneously develop multiple products through the combined utilization of seawater by solar chimney technology. A small scale experimental system was set up. The collector temperature, the seawater temperature, and the temperature and humidity of the airflow under the collector were measured. Thermal network analysis of the system was carried out. The results show that the airflow is nearly saturated at the entrance of the chimney, and the mean dry-bulb and wet-bulb temperatures of the airflow have increased by 8.4 ℃ and 9.6 ℃, respectively. The radiation heat transfer between the collector and the sky is the biggest heat loss in the system, which is up to 29.1% on average of the solar energy. However, the water evaporation heat is about 23.6% on average of the solar energy. To reduce the heat loss and enhance the water evaporation, it is necessary to reduce the emissivity and thermal conductivity of the collector and increase the evaporation areas.展开更多
To obtain the phase transformation latent heat corresponding to different cooling rates with low test workload and cost,the Newton thermal analysis method and the improved Newtonian thermal analysis method were discus...To obtain the phase transformation latent heat corresponding to different cooling rates with low test workload and cost,the Newton thermal analysis method and the improved Newtonian thermal analysis method were discussed based on the cooling curve obtained in the end-quench test.The validity of two methods was given by the latent heat calculation of 45^(#) steel.The results show that the relative error of latent heat is 5.20%through the improved Newtonian thermal analysis method,which is more accurate than the Newtonian thermal analysis method.Furthermore,the latent heat release of phase transformation of the self-designed CSU-A1 powder metallurgy nickel-based superalloy increases from 4.3 to 12.29 J/g when the cooling rate decreases from 50.15 to 33.40℃/min,because there is more sufficient time for the alloy microstructure to complete the phase transformation process when the cooling rate is smaller.展开更多
Film-boiling heat transfer is a key phenomenon governing severe accident sequence in a sodium-cooled fast reactor. Experimental the fuel-coolant interaction process which may occur during a and theoretical work on fil...Film-boiling heat transfer is a key phenomenon governing severe accident sequence in a sodium-cooled fast reactor. Experimental the fuel-coolant interaction process which may occur during a and theoretical work on film-boiling heat transfer in sodium has hardly been carried out in the past. An experiment has been conducted in the early seventies to investigate sodium pool boiling. In this experiment, a hot tantalum sphere was immersed into subcooled liquid sodium. Film boiling was obtained for various sets of parameters： sodium subcooling from 4.1 K to 29. 1 K, initial sphere temperature ranging from 1,802.6 K to 2,633.7 K, sphere diameters of 1.27, 1.91 and 2.54 cm and sodium depths of 7.6 cm and 11.4 cm. In the present work, a simplified analysis based on the boundary layer theory is developed to describe pool film-boiling heat transfer on a hot sphere in liquid sodium. Two extreme cases are considered depending on sodium subcooling. In the case of high subcooling, most of the heat lost by the sphere is used to heat the sodium while for low subcooling, it is used to vaporize the liquid at the liquid-vapor interface. It will be shown that the scaling analysis predicts the heat fluxes within the order of magnitude when compared to the available experimental data. Besides, it allows an estimation of the contribution of these fluxes to the liquid heating and vaporization processes.展开更多
This experimental analysis shows the measured reduction in energy consumption as well as the effects of voltage on cycle temperatures, pressures, flow rates and also compressor speed （revolutions per minute）. The do...This experimental analysis shows the measured reduction in energy consumption as well as the effects of voltage on cycle temperatures, pressures, flow rates and also compressor speed （revolutions per minute）. The domestic refrigerator used R134a as refrigerant. Two energy consumption procedures were adapted from the JIS and ISO standards. The biggest difference between two standards is that the fridge is not opened in the ISO test while it is opened a number of times in the JIS test. The tests were carried out between 190 V and 250 V in steps of 10 V. The reduction in energy consumption was of 49.78 W-h per day or 6.27% of the total consumption. The experiments also showed that the voltage drop resulted in only a small rpm drop which in turn did not result in a noticeable refrigerant flow-rate change. Consequently the temperatures and pressures were not affected.展开更多
基金Supported by the Chinese Academy of Sciences (No. KJ 951-B1-704), the National Natural Science Foundation of China (No. 59736130) and the State Key Fundamental Research Plan of China (No. G2000026305).
文摘This paper consists of two parts. (1) For a hollow sphere with sudden temperature changes on its inner and outer surfaces, the hyperbolic heat conduction equation is employed to describe this extreme thermal case and an analytical expression of its temperature distribution is obtained. According to the expression, the non-Fourier heat conduction behavior that will appear in the hollow sphere is studied and some qualitative conditions that will result in distinct non-Fourier behavior in the medium is ultimately attained. (2) A novel experiment to observe non-Fourier heat conduction behavior in porous material (mainly ordinary duplicating paper) heated by a microsecond laser pulse is presented. The conditions for observing distinct non-Fourier heat conduction behavior in the experimental sample agree well with the theoretical results qualitatively.
基金Project(51175122)supported by the National Natural Science Foundation of China
文摘The aim of this work is to simulate thermal deformation of tool system and investigate the influence of cutting parameters on it in single-point diamond turning(SPDT) of aluminum alloy. The experiments with various cutting parameters were conducted. Cutting temperature was measured by FLIR A315 infrared thermal imager. Tool wear was measured by scanning electron microscope(SEM). The numerical model of heat flux considering tool wear generated in cutting zone was established. Then two-step finite element method(FEM) simulations matching the experimental conditions were carried out to simulate the thermal deformation. In addition, the tests of deformation of tool system were performed to verify previous simulation results. And then the influence of cutting parameters on thermal deformation was investigated. The results show that the temperature and thermal deformation from simulations agree well with the results from experiments in the same conditions. The maximum thermal deformation of tool reaches to 7 μm. The average flank wear width and cutting speed are the dominant factors affecting thermal deformation, and the effective way to decrease the thermal deformation of tool is to control the tool wear and the cutting speed.
文摘The present investigation deals with process analysis of oxy-acetylene flame assisted double pass line heating for varying plate thickness, oxy-acetylene flame as the heat source for multi pass line heating to achieve 3-D bending of plates with varying thicknesses was studied. The oxy-acetylene flame was modeled as the moving heat source in the FEM analysis. The transient thermal histories were predicted taking into account the temperature dependent thermo-mechanical properties. A comparative study between single pass and double pass line heating residual deformation was also carried out. The temperature distribution and residual detbrmations predicted by the numerical model developed in the present work compared fairly well with those of the experimental ones.
基金Projects(51264023,51364020,U1202271)supported by the National Natural Science Foundation of ChinaProject(IRT1250)supported by the Program for Innovative Research Team in University of Ministry of Education of ChinaProject(2014HA003)supported by the Yunnan Province Science and Technology Talents Program,China
文摘Desulfurization experiments of CuO, γ-Al2O3 and CuO/γ-Al2O3 were made in simulated flue gas by means of thermogravimetric analysis. It is found that reaction activities of CuO supported on γ-Al2O3 could be highly improved. Desulfurization kinetics of CuO/γ-Al2O3 was studied in the temperature range of 250 °C-400 °C and SO2 concentration of 0.1%-0.9%. The experimental data were tested and compared with kinetics models of volume reaction model(VRM), grain size model(GSM), random pore model(RPM) and pore-blocking model(PBM). Correlation analysis shows that VRM and RPM models do not fit experimental data well. GSM contradicts with the changes in the physical and chemical properties of Cu O/γ-Al2O3 as the desulfurization proceeds. It is found that PBM is consistent with the change of pore structure of CuO/γ-Al2O3 sorbent during desulfurization process and predicts the conversion-time curves of the sorbent well. Meanwhile, kinetics parameters are obtained and discussed.
文摘In this work an experimental study combined with an analytical investigation for cooling superheated Carbon Dioxide （CO2） gas were carried out. This work is intended to be part of the super critical Gustav Lorentzen refrigeration cycle of CO2. Experimental and analytical works concentrated on heat transfer and pressure drop for single phase flow during gas cooling inside tubes filled with porous media. Analytical empirical correlations were formulated for the coefficient of convectional heat transfer and for the pressure drop. A comparison between experimental results and that obtained by developed correlations were carried out, and a comparison between these results and literature published ones were carried out too. The results of this research showed that for cooling process the proposed correlations were proved to be acceptably accurate for pressure drop with difference from experimental results of 2%, while for convective heat transfer the difference from experimental results reached about 3%. More than 90% agreement with literature results was obtained. This work can enhance the calculations of heat flux and pressure drop of gases flow inside porous media filled tubes, and can help in the design procedure of heat exchangers and cooling processes.
基金Project(2006BAJ04A15-03) supported by the National Science and Technology Pillar Program during the Eleventh Five-year Plan Period
文摘From the viewpoints of environmental conservation and energy efficiency,seawater-source heat pump system(SWHP) to provide district cooling and heating is applied in coastal areas.Based on the system,a heat transfer model was established for cast heat exchanger(CHE) adopted by SWHP systems.The CHE consists of pipes immersed in the seawater and used for transferring heat between the seawater and the heat exchanger pipes of SWHP system.An experimental study was carried out to test the validity of the model.A program was developed in VB language and the effects of inlet temperature,flow rate of the secondary refrigerant and length of CHE on the results were investigated.The results of the numerical simulation are in consistence with the experiments in both winter and summer conditions.As a result,application of SWHP systems with CHE in coastal areas in China is feasible due to the favorable geographical conditions and environment.
基金Supported by Tianjin Technological Development Program Project of China (No05YFGZSF02800 and No06YFSZSF04600)the Key Research Program of the National Eleventh Five-Year Plan of China (No 2006BAA04B03-03)
文摘It is promising to simultaneously develop multiple products through the combined utilization of seawater by solar chimney technology. A small scale experimental system was set up. The collector temperature, the seawater temperature, and the temperature and humidity of the airflow under the collector were measured. Thermal network analysis of the system was carried out. The results show that the airflow is nearly saturated at the entrance of the chimney, and the mean dry-bulb and wet-bulb temperatures of the airflow have increased by 8.4 ℃ and 9.6 ℃, respectively. The radiation heat transfer between the collector and the sky is the biggest heat loss in the system, which is up to 29.1% on average of the solar energy. However, the water evaporation heat is about 23.6% on average of the solar energy. To reduce the heat loss and enhance the water evaporation, it is necessary to reduce the emissivity and thermal conductivity of the collector and increase the evaporation areas.
基金the financial supports from the National Key Research and Development Program of China(No.2016YFB0700300)the Postgraduate Independent Exploration and Innovation Project of Central South University,China(No.2019zzts262)。
文摘To obtain the phase transformation latent heat corresponding to different cooling rates with low test workload and cost,the Newton thermal analysis method and the improved Newtonian thermal analysis method were discussed based on the cooling curve obtained in the end-quench test.The validity of two methods was given by the latent heat calculation of 45^(#) steel.The results show that the relative error of latent heat is 5.20%through the improved Newtonian thermal analysis method,which is more accurate than the Newtonian thermal analysis method.Furthermore,the latent heat release of phase transformation of the self-designed CSU-A1 powder metallurgy nickel-based superalloy increases from 4.3 to 12.29 J/g when the cooling rate decreases from 50.15 to 33.40℃/min,because there is more sufficient time for the alloy microstructure to complete the phase transformation process when the cooling rate is smaller.
文摘Film-boiling heat transfer is a key phenomenon governing severe accident sequence in a sodium-cooled fast reactor. Experimental the fuel-coolant interaction process which may occur during a and theoretical work on film-boiling heat transfer in sodium has hardly been carried out in the past. An experiment has been conducted in the early seventies to investigate sodium pool boiling. In this experiment, a hot tantalum sphere was immersed into subcooled liquid sodium. Film boiling was obtained for various sets of parameters： sodium subcooling from 4.1 K to 29. 1 K, initial sphere temperature ranging from 1,802.6 K to 2,633.7 K, sphere diameters of 1.27, 1.91 and 2.54 cm and sodium depths of 7.6 cm and 11.4 cm. In the present work, a simplified analysis based on the boundary layer theory is developed to describe pool film-boiling heat transfer on a hot sphere in liquid sodium. Two extreme cases are considered depending on sodium subcooling. In the case of high subcooling, most of the heat lost by the sphere is used to heat the sodium while for low subcooling, it is used to vaporize the liquid at the liquid-vapor interface. It will be shown that the scaling analysis predicts the heat fluxes within the order of magnitude when compared to the available experimental data. Besides, it allows an estimation of the contribution of these fluxes to the liquid heating and vaporization processes.
文摘This experimental analysis shows the measured reduction in energy consumption as well as the effects of voltage on cycle temperatures, pressures, flow rates and also compressor speed （revolutions per minute）. The domestic refrigerator used R134a as refrigerant. Two energy consumption procedures were adapted from the JIS and ISO standards. The biggest difference between two standards is that the fridge is not opened in the ISO test while it is opened a number of times in the JIS test. The tests were carried out between 190 V and 250 V in steps of 10 V. The reduction in energy consumption was of 49.78 W-h per day or 6.27% of the total consumption. The experiments also showed that the voltage drop resulted in only a small rpm drop which in turn did not result in a noticeable refrigerant flow-rate change. Consequently the temperatures and pressures were not affected.
