The molecular level mixing method was extended to fabricate carbon nanotube reinforced silver composite. The influence of type of carbon nanotubes（single/multiwall） reinforcement and their mode of functionalization...The molecular level mixing method was extended to fabricate carbon nanotube reinforced silver composite. The influence of type of carbon nanotubes（single/multiwall） reinforcement and their mode of functionalization（covalent/non-covalent） on thermal conductivity of silver composite was investigated. X-ray diffraction and electron diffraction spectroscopy（EDS） confirm the presence of silver and carbon in the composite powder. High resolution scanning electron microscopy and transmission electron microscopy ascertain embedded, anchored and homogeneously implanted carbon nanotubes in silver matrix. Effect of covalent functionalization on multiwall carbon nanotubes was monitored by Raman and Fourier transform infrared spectroscopy. These investigations confirm the addition of functional groups and structural integrity of carbon nanotubes even after covalent functionalization. Thermal conductivity of composites was measured by a laser flash technique and theoretically analyzed using an effective medium approach. The experimental results reveal that thermal conductivity decreases after incorporation of covalently functionalized multiwall nanotubes and single wall carbon nanotubes. However, non-covalently functionalized multiwall nanotube reinforcement leads to the increase in effective thermal conductivity of the composite and is in agreement with theoretical predictions derived from effective medium theory, in absence of interfacial thermal resistance.展开更多
Based on modified silicon polyester resin in addition to several functional fillers such as corrosion-resistant fillers, heat-resistant fillers and thermal conductive fillers, a high thermal conductive coating can be ...Based on modified silicon polyester resin in addition to several functional fillers such as corrosion-resistant fillers, heat-resistant fillers and thermal conductive fillers, a high thermal conductive coating can be made. On the basis of boronnitride(BN) and aluminum nitride(AIN) used as thermal conductive fillers and by means of the testing system of hot disk and heat transfer experiment, researches on the varieties of thermal conductive fillers and the effects of the contents of high-thermal conductive coating have been done, which shows that the thermal conductivity of coating increases with the increase of the quality fraction and the coefficient of thermal conductivity of the thermal conductive fillers of coating. With guaranteeing better heat resistance, stronger corrosion resistance and adhesive force, the coefficient of coating can reach a level as high as 3 W·m-1·K-1.展开更多
The axisymmetric thermoelastic problem of a uniformly heated, functionally graded isotropic hollow cylinder is considered. An analytical form of solution is proposed. For the case when the Young's modulus and ther...The axisymmetric thermoelastic problem of a uniformly heated, functionally graded isotropic hollow cylinder is considered. An analytical form of solution is proposed. For the case when the Young's modulus and thermal expansion coefficient have a power\|law dependence on the radial coordinate, explicit exact solution is obtained. For the degenerated case, i.e. when the cylinder is homogeneous and isotropic, no stresses will occur provided it is subjected to a uniform temperature. Numerical results are finally given and some important inclusions are obtained.展开更多
The lattice parameters, bulk modulus, phase transition pressure, and temperature dependencies of the elastic constants cij of CdSe are investigated by using the Cambridge Serial Total Energy Package （CASTEP） program...The lattice parameters, bulk modulus, phase transition pressure, and temperature dependencies of the elastic constants cij of CdSe are investigated by using the Cambridge Serial Total Energy Package （CASTEP） program in the frame of Density Functional Theory （DFT）. It is found that the phase transitions from the ZB structure to the RS structure and from WZ structure to RS structure are 2.2 GPa and 2.8 GPa, respectively. Our results agree well with the available experimental data and other theoretical results. The aggregate elastic modulus （B, G, E, A ）, the Poisson＇s ratio （v）, the Griuneisen parameter （γ）, the Debye temperature θD on pressure and temperature are also successfully obtained.展开更多
Micro-scale functionally graded material(FGM)pipes conveying fluid have many significant applications in engineering fields.In this work,the thermoelastic vibration of FGM fluid-conveying tubes in elastic medium is st...Micro-scale functionally graded material(FGM)pipes conveying fluid have many significant applications in engineering fields.In this work,the thermoelastic vibration of FGM fluid-conveying tubes in elastic medium is studied.Based on modified couple stress theory and Hamilton’s principle,the governing equation and boundary conditions are obtained.The differential quadrature method(DQM)is applied to investigating the thermoelastic vibration of the FGM pipes.The effect of temperature variation,scale effect of the microtubule,micro-fluid effect,material properties,elastic coefficient of elastic medium and outer radius on thermoelastic vibration of the FGM pipes conveying fluid are studied.The results show that in the condition of considering the scale effect and micro-fluid of the microtubule,the critical dimensionless velocity of the system is higher than that of the system which calculated using classical macroscopic model.The results also show that the variations of temperature,material properties,elastic coefficient and outer radius have significant influences on the first-order dimensionless natural frequency.展开更多
Changes in tissue structure, rheological properties and water content of raw and heated sea cucumber meat were studied. Sea cucumber Stichopus japonicus was heated at 25℃, 70℃ and 100℃ water for 5 min. The structur...Changes in tissue structure, rheological properties and water content of raw and heated sea cucumber meat were studied. Sea cucumber Stichopus japonicus was heated at 25℃, 70℃ and 100℃ water for 5 min. The structural changes were observed using a light microscope and the rheological parameters （rupture strength, adhesive strength and deformation） determined using a texture meter. Microscopic photograph revealed that the structural change of heated meat was greater than that of raw meat. The rupture strength, adhesive strength and deformation of raw meat were smaller than those of the heated meat. Meanwhile, rheological parameters showed positive correlation with heating temperature. These changes are mainly caused by thermal denaturation and gelatinization of collagen during heating. These changes were also evidenced in observations using a light microscope and differential scanning calorimetry.展开更多
A novel thennoelectric generating and performance measuring system （TGPMS） was designed and fabricated. TGPMS can not only achieve the function of thennoelectric generation, but also measure the thennoelectric perfo...A novel thennoelectric generating and performance measuring system （TGPMS） was designed and fabricated. TGPMS can not only achieve the function of thennoelectric generation, but also measure the thennoelectric performance parameters of the bismuth-telluride-based thennoelectric device accurately. These thennoelectric performance parameters mainly include the dependence of the Seebeck coefficient of the thennoelectric device on the device＇s temperature in the low temperature range （about 40 ~ 190~C ）, and the dependence of the power output and thermoelectric conversion efficiency on the temperature dif- ference or output load. With the optimum load, the optimal value of the power output is 3.39W when the temperature difference reaches 231.2~C, and the optimal value of the conversion efficiency is 3.22% when the temperature difference reaches 208.9~C. TGPMS provides an experimental foundation for the application of the thennoelectric generators in the space field.展开更多
In order to improve the toughness of the cured aromatic tetrafunctional epoxy resins, a dlmer rarboxylic acid named dlmer fatty acid （DFA） was used to modify an aromatic tetrafunctional epoxy, N, N, N＇, N＇-tetragl...In order to improve the toughness of the cured aromatic tetrafunctional epoxy resins, a dlmer rarboxylic acid named dlmer fatty acid （DFA） was used to modify an aromatic tetrafunctional epoxy, N, N, N＇, N＇-tetraglycidyl-2,2-bis [ 4-（ 4-aminophcuoxy ） phenyl ] propane （TGBAPP）. The curing behaviors of DFA- TGBAPP/MNA （ methyl nadic anhydride） systems were studied by differential scanning calorimetry （DSC） method. And the thermal properties of the cured epoxy resin were investigated with the thermo-gravimetric analysis （TGA） and dynamic mechanical analysis （DMA）. Besides, the toughness was characterized with the impact strength tested by charpy impact testing. The results indicated that the modification would improve the curing reactions, and the curing temperatures were decreased with the increasing content of DFA. The thermal properties were not influenced obviously, and the toughness could be improved when the epoxy resin was modified with DFA.展开更多
Food technology has been instrumental in ensuring that troops remain ＂fit to fight＂. Early food technologies produced flat bread, hard biscuits, cheese and salted meat, allowing Roman legionaries to carry rations fo...Food technology has been instrumental in ensuring that troops remain ＂fit to fight＂. Early food technologies produced flat bread, hard biscuits, cheese and salted meat, allowing Roman legionaries to carry rations for several days. Canning was invented in the late 18th century in response to the French Government＇s offer of a substantial reward to the person whose invention would allow troops to carry their food when marching long distances. World War II saw further advances in the form of stable and palatable canned meals, compressed cereal bars, candy-coated peanuts and other innovative foods in US combat rations. Two significant technology breakthroughs in the second half of the 20th century have altered the form of military rations. Freeze drying matured as an industrial technology, allowing the production of long-life, light-weight rations. Flexible packaging, based on plastic laminates, led to reduced weight and less waste disposal through the development of retort pouched meals （meals in flexible packaging that have undergone heat sterilization）, which have largely replaced metal cans in combat rations. Improvements in quality of military rations, particularly their organoleptic properties, are emerging through application of innovative technologies such as high-pressure thermal processing, pulsed electric field, and microwave assisted thermal sterilization. Research and development of ＂functional foods＂, such as those containing added essential fatty acids or probiotics offers the potential to provide combat rations that can further improve soldier health and performance.展开更多
Hemorrhagic fever with renal syndrome (HFRS) is a disease caused by viruses of the family Bunyaviridae,genus Hantavirus.HFRS from Dobrava virus (DOBV) is a seldom reported disease in Albania.Clinically HFRS is manifes...Hemorrhagic fever with renal syndrome (HFRS) is a disease caused by viruses of the family Bunyaviridae,genus Hantavirus.HFRS from Dobrava virus (DOBV) is a seldom reported disease in Albania.Clinically HFRS is manifested as mild,moderate,or severe.Therefore,the number of cases of Hantavirus' infection may be underestimated,and should be included in the differential diagnosis of many acute infections,hematologic diseases,acute abdominal diseases and renal diseases complicated by acute renal failure.We report here an atypical presentation of HFRS from Dobrava virus complicated by orchitis with a positive outcome.展开更多
Two kinds of rosin derivatives, （2-hydroxy-3-（methacryloyloxy）propyl 7-isopropyl-1,4a-dimethyl-1,2,3,4,4a,4b,5,6,10,10a- decahydrophenanthrene-1-carboxylate） （HMPIDDC） and （（（7-isopropyl-1,4a-dimethyl-1,2,3,4...Two kinds of rosin derivatives, （2-hydroxy-3-（methacryloyloxy）propyl 7-isopropyl-1,4a-dimethyl-1,2,3,4,4a,4b,5,6,10,10a- decahydrophenanthrene-1-carboxylate） （HMPIDDC） and （（（7-isopropyl-1,4a-dimethyl-1,2,3,4,4a,9,10,10a-octahydrophenan- thren-1-yl）methyl）azanediyl）bis（2-hydroxypropane-3,1-diyl）bis（2-methylacrylate） （IDOMAHM） were synthesized under mild and easy to implement conditions. The two derivatives were employed as the rigid monomers to copolymerize with acrylated epoxidized soybean oil （AESO）, as so to improve the performance of the cured resins. The chemical structures of HMPIDDC and IDOMAHM were confirmed by nuclear magnetic resonance （NMR） and Fourier Transform Infrared （FT-IR） before copolymerization. The curing behaviors of pristine AESO, AESO/HMPIDDC blend, and AESO/IDOMAHM blend were monitored by differential scanning calorimetry （DSC）. Moreover, the thermal and mechanical properties of the cured resins were evaluated by universal mechanical testing, dynamic mechanical analysis （DMA） and thermogravimetric analysis （TGA）. The results demonstrated that after the introduction of HMPIDDC and IDOMAHM, the glass transition temperature and mechanical properties of the copolymerized resin were significantly increased. In one word, HMPIDDC and IDOMAHM showed dramatic potential to be used as bio-based compounds to improve the properties of soybean-oil based thermosets.展开更多
An experimental system of flat plate pulsating heat pipe was established and experimental research was carried out in this system to know the mechanism of heat transfer, start-up and operating characteristics. The fac...An experimental system of flat plate pulsating heat pipe was established and experimental research was carried out in this system to know the mechanism of heat transfer, start-up and operating characteristics. The factors, such as filling rate, heating power, heating method etc, which have great influence on the thermal performance of the plate pulsating heat pipe were discussed. The results indicate that heating power and filling rate are the important factors for the start-up of the plate pulsating heat pipe. The different start-up power is needed with different filling rate, and the start-up of the heat pipe in case of bottom heated is much easier than that of top heated. Increasing the heating power and enlarging the heating area can make the start-up easier. Heating power can also affect the start-up time of heat pipe under the condition of bottom heated, while it does not have some influence to the heat pipe of top heated. The thermal resistance of plate pulsating heat pipe is related with the heating power, and the higher the heating power is, the smaller the thermal resistance is. But the best filling rate which the heat pipe needs is different with different heating methods, and the performance of the heat pipe in the case of bottom heated is better than the others.展开更多
Antimony-based Zintl compounds AM2Sb2(A=Ca,Sr,Ba,Yb,Eu;M=Mg,Zn,Cd,Mn),which enable a broad range of manipulation on electrical and thermal transport properties,are considered as an important class of thermoelectric ma...Antimony-based Zintl compounds AM2Sb2(A=Ca,Sr,Ba,Yb,Eu;M=Mg,Zn,Cd,Mn),which enable a broad range of manipulation on electrical and thermal transport properties,are considered as an important class of thermoelectric materials.Phonon and carrier transport engineering were realized in YbMg2Sb2 via equivalent and aliovalent substitution of Zn and Ag,respectively.The roomtemperature thermal conductivity reduces from 1.96 to 1.15 W m^-1 K^-1 for YbMg2-xZnxSb2 due to the mass and strain fluctuation through the formation of the absolute solid solution of YbMg2Sb2-YbZn2Sb2.Furthermore,the carrier concentration has been further optimized by Ag doping(from 0.42×10^19 to 7.72×10^19 cm^-3 at room temperature),and thus the electrical conductivity and the power factor are enhanced effectively.The integrated aspects make the dimensionless figure of merit(zT)reach 0.48 at 703 K,which is 60%higher than the pristine YbMgZnSb2 sample.展开更多
LED lighting has problems such as short life span, power reduction due to the LED chip's heat, and decreased luminance efficiency etc. Many studies on the optimization of the thermal performance of LEDs have been ...LED lighting has problems such as short life span, power reduction due to the LED chip's heat, and decreased luminance efficiency etc. Many studies on the optimization of the thermal performance of LEDs have been conducted actively to solve these problems. The present study changes the fin shape and intervals of various heat sink designs so that LED can effectively produce a thermal effect. The water-cooling heat release system and the heat pipe methods show higher thermal performance results than the existing systems; however, the system is of high cost and requires a large-scale apparatus. This study carried out a numerical analysis of the thermal control system by applying heat flux and heat sink properties as an active heat release system using the commercial code ANSYS ver. 13.0 and verified the validity of the new heat sink design for temperature distribution analysis.展开更多
基金support from Department of Science and Technology [Project-SR/FTP/PS-054/2011(G)]
文摘The molecular level mixing method was extended to fabricate carbon nanotube reinforced silver composite. The influence of type of carbon nanotubes（single/multiwall） reinforcement and their mode of functionalization（covalent/non-covalent） on thermal conductivity of silver composite was investigated. X-ray diffraction and electron diffraction spectroscopy（EDS） confirm the presence of silver and carbon in the composite powder. High resolution scanning electron microscopy and transmission electron microscopy ascertain embedded, anchored and homogeneously implanted carbon nanotubes in silver matrix. Effect of covalent functionalization on multiwall carbon nanotubes was monitored by Raman and Fourier transform infrared spectroscopy. These investigations confirm the addition of functional groups and structural integrity of carbon nanotubes even after covalent functionalization. Thermal conductivity of composites was measured by a laser flash technique and theoretically analyzed using an effective medium approach. The experimental results reveal that thermal conductivity decreases after incorporation of covalently functionalized multiwall nanotubes and single wall carbon nanotubes. However, non-covalently functionalized multiwall nanotube reinforcement leads to the increase in effective thermal conductivity of the composite and is in agreement with theoretical predictions derived from effective medium theory, in absence of interfacial thermal resistance.
基金Supported by the State Key Development of Basic Research of China(2001CB710703)the National Natural Science Foundation of China(51176053)+2 种基金the Key Technologies R&D Program of Guangdong Province(2011B090400562)the Strategic Emerging Industry Special Funds of Guangdong Province(2012A080304015)the Key Technologies R&D Program of Guangzhou City(2010U1-D00221,2011Y5000006)
文摘Based on modified silicon polyester resin in addition to several functional fillers such as corrosion-resistant fillers, heat-resistant fillers and thermal conductive fillers, a high thermal conductive coating can be made. On the basis of boronnitride(BN) and aluminum nitride(AIN) used as thermal conductive fillers and by means of the testing system of hot disk and heat transfer experiment, researches on the varieties of thermal conductive fillers and the effects of the contents of high-thermal conductive coating have been done, which shows that the thermal conductivity of coating increases with the increase of the quality fraction and the coefficient of thermal conductivity of the thermal conductive fillers of coating. With guaranteeing better heat resistance, stronger corrosion resistance and adhesive force, the coefficient of coating can reach a level as high as 3 W·m-1·K-1.
文摘The axisymmetric thermoelastic problem of a uniformly heated, functionally graded isotropic hollow cylinder is considered. An analytical form of solution is proposed. For the case when the Young's modulus and thermal expansion coefficient have a power\|law dependence on the radial coordinate, explicit exact solution is obtained. For the degenerated case, i.e. when the cylinder is homogeneous and isotropic, no stresses will occur provided it is subjected to a uniform temperature. Numerical results are finally given and some important inclusions are obtained.
基金National Natural Science Foundation of China under Grant No.10576020
文摘The lattice parameters, bulk modulus, phase transition pressure, and temperature dependencies of the elastic constants cij of CdSe are investigated by using the Cambridge Serial Total Energy Package （CASTEP） program in the frame of Density Functional Theory （DFT）. It is found that the phase transitions from the ZB structure to the RS structure and from WZ structure to RS structure are 2.2 GPa and 2.8 GPa, respectively. Our results agree well with the available experimental data and other theoretical results. The aggregate elastic modulus （B, G, E, A ）, the Poisson＇s ratio （v）, the Griuneisen parameter （γ）, the Debye temperature θD on pressure and temperature are also successfully obtained.
文摘Micro-scale functionally graded material(FGM)pipes conveying fluid have many significant applications in engineering fields.In this work,the thermoelastic vibration of FGM fluid-conveying tubes in elastic medium is studied.Based on modified couple stress theory and Hamilton’s principle,the governing equation and boundary conditions are obtained.The differential quadrature method(DQM)is applied to investigating the thermoelastic vibration of the FGM pipes.The effect of temperature variation,scale effect of the microtubule,micro-fluid effect,material properties,elastic coefficient of elastic medium and outer radius on thermoelastic vibration of the FGM pipes conveying fluid are studied.The results show that in the condition of considering the scale effect and micro-fluid of the microtubule,the critical dimensionless velocity of the system is higher than that of the system which calculated using classical macroscopic model.The results also show that the variations of temperature,material properties,elastic coefficient and outer radius have significant influences on the first-order dimensionless natural frequency.
基金supported by the proiect sponsored by the Scientific Research Foundation for Returned Overseas Chinese Scholars,State Education Ministry(SRF for ROCS,SEM)the Natural Science Foundation of Shandong(No.2004BSO7003)and Qingdao(No.04-2-JZ-110)
文摘Changes in tissue structure, rheological properties and water content of raw and heated sea cucumber meat were studied. Sea cucumber Stichopus japonicus was heated at 25℃, 70℃ and 100℃ water for 5 min. The structural changes were observed using a light microscope and the rheological parameters （rupture strength, adhesive strength and deformation） determined using a texture meter. Microscopic photograph revealed that the structural change of heated meat was greater than that of raw meat. The rupture strength, adhesive strength and deformation of raw meat were smaller than those of the heated meat. Meanwhile, rheological parameters showed positive correlation with heating temperature. These changes are mainly caused by thermal denaturation and gelatinization of collagen during heating. These changes were also evidenced in observations using a light microscope and differential scanning calorimetry.
基金the High Technology Research and Development Program of China(No2003AA005031)
文摘A novel thennoelectric generating and performance measuring system （TGPMS） was designed and fabricated. TGPMS can not only achieve the function of thennoelectric generation, but also measure the thennoelectric performance parameters of the bismuth-telluride-based thennoelectric device accurately. These thennoelectric performance parameters mainly include the dependence of the Seebeck coefficient of the thennoelectric device on the device＇s temperature in the low temperature range （about 40 ~ 190~C ）, and the dependence of the power output and thermoelectric conversion efficiency on the temperature dif- ference or output load. With the optimum load, the optimal value of the power output is 3.39W when the temperature difference reaches 231.2~C, and the optimal value of the conversion efficiency is 3.22% when the temperature difference reaches 208.9~C. TGPMS provides an experimental foundation for the application of the thennoelectric generators in the space field.
基金Shanghai Leading Academic Discipline Project,China(No.s30107)the Program for Professor of Special Appointment(Eastern Scholar)at Shanghai Institutions of Higher Learning,Chinathe Project of Shanghai Science and Technology Committee,China(No.12520500300)
文摘In order to improve the toughness of the cured aromatic tetrafunctional epoxy resins, a dlmer rarboxylic acid named dlmer fatty acid （DFA） was used to modify an aromatic tetrafunctional epoxy, N, N, N＇, N＇-tetraglycidyl-2,2-bis [ 4-（ 4-aminophcuoxy ） phenyl ] propane （TGBAPP）. The curing behaviors of DFA- TGBAPP/MNA （ methyl nadic anhydride） systems were studied by differential scanning calorimetry （DSC） method. And the thermal properties of the cured epoxy resin were investigated with the thermo-gravimetric analysis （TGA） and dynamic mechanical analysis （DMA）. Besides, the toughness was characterized with the impact strength tested by charpy impact testing. The results indicated that the modification would improve the curing reactions, and the curing temperatures were decreased with the increasing content of DFA. The thermal properties were not influenced obviously, and the toughness could be improved when the epoxy resin was modified with DFA.
文摘Food technology has been instrumental in ensuring that troops remain ＂fit to fight＂. Early food technologies produced flat bread, hard biscuits, cheese and salted meat, allowing Roman legionaries to carry rations for several days. Canning was invented in the late 18th century in response to the French Government＇s offer of a substantial reward to the person whose invention would allow troops to carry their food when marching long distances. World War II saw further advances in the form of stable and palatable canned meals, compressed cereal bars, candy-coated peanuts and other innovative foods in US combat rations. Two significant technology breakthroughs in the second half of the 20th century have altered the form of military rations. Freeze drying matured as an industrial technology, allowing the production of long-life, light-weight rations. Flexible packaging, based on plastic laminates, led to reduced weight and less waste disposal through the development of retort pouched meals （meals in flexible packaging that have undergone heat sterilization）, which have largely replaced metal cans in combat rations. Improvements in quality of military rations, particularly their organoleptic properties, are emerging through application of innovative technologies such as high-pressure thermal processing, pulsed electric field, and microwave assisted thermal sterilization. Research and development of ＂functional foods＂, such as those containing added essential fatty acids or probiotics offers the potential to provide combat rations that can further improve soldier health and performance.
文摘Hemorrhagic fever with renal syndrome (HFRS) is a disease caused by viruses of the family Bunyaviridae,genus Hantavirus.HFRS from Dobrava virus (DOBV) is a seldom reported disease in Albania.Clinically HFRS is manifested as mild,moderate,or severe.Therefore,the number of cases of Hantavirus' infection may be underestimated,and should be included in the differential diagnosis of many acute infections,hematologic diseases,acute abdominal diseases and renal diseases complicated by acute renal failure.We report here an atypical presentation of HFRS from Dobrava virus complicated by orchitis with a positive outcome.
基金supported by the Youth Innovation Promotion Association of the Chinese Academy of Sciences(Grant No.2012229)Natural Sciences Foundation of Ningbo City(Grant No.2014A610110)+1 种基金Research Project of Technology Application for Public Welfare of Zhejiang Province(Grant No.2014C31143)National Natural Science Foundation of China(Grant Nos.51373194,51203176)
文摘Two kinds of rosin derivatives, （2-hydroxy-3-（methacryloyloxy）propyl 7-isopropyl-1,4a-dimethyl-1,2,3,4,4a,4b,5,6,10,10a- decahydrophenanthrene-1-carboxylate） （HMPIDDC） and （（（7-isopropyl-1,4a-dimethyl-1,2,3,4,4a,9,10,10a-octahydrophenan- thren-1-yl）methyl）azanediyl）bis（2-hydroxypropane-3,1-diyl）bis（2-methylacrylate） （IDOMAHM） were synthesized under mild and easy to implement conditions. The two derivatives were employed as the rigid monomers to copolymerize with acrylated epoxidized soybean oil （AESO）, as so to improve the performance of the cured resins. The chemical structures of HMPIDDC and IDOMAHM were confirmed by nuclear magnetic resonance （NMR） and Fourier Transform Infrared （FT-IR） before copolymerization. The curing behaviors of pristine AESO, AESO/HMPIDDC blend, and AESO/IDOMAHM blend were monitored by differential scanning calorimetry （DSC）. Moreover, the thermal and mechanical properties of the cured resins were evaluated by universal mechanical testing, dynamic mechanical analysis （DMA） and thermogravimetric analysis （TGA）. The results demonstrated that after the introduction of HMPIDDC and IDOMAHM, the glass transition temperature and mechanical properties of the copolymerized resin were significantly increased. In one word, HMPIDDC and IDOMAHM showed dramatic potential to be used as bio-based compounds to improve the properties of soybean-oil based thermosets.
基金support of this work by the National Natural Science Foundation of China (No.50776006)
文摘An experimental system of flat plate pulsating heat pipe was established and experimental research was carried out in this system to know the mechanism of heat transfer, start-up and operating characteristics. The factors, such as filling rate, heating power, heating method etc, which have great influence on the thermal performance of the plate pulsating heat pipe were discussed. The results indicate that heating power and filling rate are the important factors for the start-up of the plate pulsating heat pipe. The different start-up power is needed with different filling rate, and the start-up of the heat pipe in case of bottom heated is much easier than that of top heated. Increasing the heating power and enlarging the heating area can make the start-up easier. Heating power can also affect the start-up time of heat pipe under the condition of bottom heated, while it does not have some influence to the heat pipe of top heated. The thermal resistance of plate pulsating heat pipe is related with the heating power, and the higher the heating power is, the smaller the thermal resistance is. But the best filling rate which the heat pipe needs is different with different heating methods, and the performance of the heat pipe in the case of bottom heated is better than the others.
基金supported by the National Key Research and Development Program of China (2018YFA0702100)the National Natural Science Foundation of China (21771123)+2 种基金the Programme of Introducing Talents of Discipline to Universities (D16002)the Science and Technology Commission of Shanghai Municipality (15DZ2260300)Key Laboratory of Optoelectronic Materials Chemistry and Physics, Chinese Academy of Sciences (2008DP173016)
文摘Antimony-based Zintl compounds AM2Sb2(A=Ca,Sr,Ba,Yb,Eu;M=Mg,Zn,Cd,Mn),which enable a broad range of manipulation on electrical and thermal transport properties,are considered as an important class of thermoelectric materials.Phonon and carrier transport engineering were realized in YbMg2Sb2 via equivalent and aliovalent substitution of Zn and Ag,respectively.The roomtemperature thermal conductivity reduces from 1.96 to 1.15 W m^-1 K^-1 for YbMg2-xZnxSb2 due to the mass and strain fluctuation through the formation of the absolute solid solution of YbMg2Sb2-YbZn2Sb2.Furthermore,the carrier concentration has been further optimized by Ag doping(from 0.42×10^19 to 7.72×10^19 cm^-3 at room temperature),and thus the electrical conductivity and the power factor are enhanced effectively.The integrated aspects make the dimensionless figure of merit(zT)reach 0.48 at 703 K,which is 60%higher than the pristine YbMgZnSb2 sample.
基金Financial aid from the Korea Ministry of Education through the Brain Korea 21 Project [HRD Center for Convergence Mechanical System Design] is gratefully acknowledgedthe financial support of Sungkyunkwan University for his sabbatical year
文摘LED lighting has problems such as short life span, power reduction due to the LED chip's heat, and decreased luminance efficiency etc. Many studies on the optimization of the thermal performance of LEDs have been conducted actively to solve these problems. The present study changes the fin shape and intervals of various heat sink designs so that LED can effectively produce a thermal effect. The water-cooling heat release system and the heat pipe methods show higher thermal performance results than the existing systems; however, the system is of high cost and requires a large-scale apparatus. This study carried out a numerical analysis of the thermal control system by applying heat flux and heat sink properties as an active heat release system using the commercial code ANSYS ver. 13.0 and verified the validity of the new heat sink design for temperature distribution analysis.
