Efficient use of timber is a vital concern problem, especially in these regions where the forestry coverage ratio is decreasing. Studies on physical modification of wood have been taken more attention due to the incre...Efficient use of timber is a vital concern problem, especially in these regions where the forestry coverage ratio is decreasing. Studies on physical modification of wood have been taken more attention due to the increasing attentions on environmental protection. Thermal modification is emphasized and developed quickly in developing countries, especially in European countries. A large number of researches have been conducted and some industrial production plants have been built. This paper reviewed the history of heat treatment, exemplifies the industrial developments in several European countries, summarized the basic principle of heat treatment and describes the environmental characteristics. The properties of heat-treated wood and its usage are also summed up.展开更多
A comparative study of the influence of elevated temperature on foam geopolymer using circulating fluidized bed combustion fly ash（CFA） was reported. Foam geopoymers were prepared with different amounts of foam agen...A comparative study of the influence of elevated temperature on foam geopolymer using circulating fluidized bed combustion fly ash（CFA） was reported. Foam geopoymers were prepared with different amounts of foam agent and different Si O2/Al2O3 molar ratios of 3.1, 3.4, and 3.8. The mechanical, thermo-physical properties and microstructure of the foam geopolymers before and after exposure to elevated temperature of 800, 1000, and 1200 ℃ were investigated. The specimen with Si O2/Al2O3 molar ratio of 3.8 exhibits the highest compressive strength, better microstructure and dimension stability before and after firing. Carnegeite, nepheline, and zeolite crystalline phases appearing after exposure may contribute to the good post-exposure strength. Low weight foam geopolymer using CFA can increase strength and maintain higher stability as high as 1000 ℃.展开更多
Due to the oxygen storage and release properties,cerium zirconium mixed oxides are recognized as the key material in automotive three-way catalysts.To reveal the effects of co-precipitation temperature on structure,ph...Due to the oxygen storage and release properties,cerium zirconium mixed oxides are recognized as the key material in automotive three-way catalysts.To reveal the effects of co-precipitation temperature on structure,physical and chemical properties of multi-doped cerium zirconium mixed oxides,a series of La and Y doped cerium zirconium mixed oxides(CZLYs)were synthesized via a co-precipitation method,and the physical and chemical properties of CZLYs were systemically characterized by XRD,N_(2) adsorption−desorption,TEM,XPS,oxygen storage capacity(OSC)and hydrogen temperature programmed reduction(H_(2)-TPR).The results show that co-precipitation temperature is an important parameter to influence the crystal size,oxygen storage capacity and thermal stability of CZLYs.When the co-precipitation temperature was 60℃,the best redox properties and thermal stability of CZLYs were obtained.After thermal treatment at 1100℃for 10 h,the specific surface area and oxygen storage capacity of the corresponding aged sample were 15.42 m^(2)/g and 497.7μmol/g,respectively.In addition,a mechanism was proposed to reveal the effects of co-precipitation temperature on the structure and properties of CZLYs.展开更多
The effects of heat treatment process on microstrucature, micro-yield strength and dynamic dimensional stability of ZL114A aluminum alloy were investigated by optical microscopy （OM）, transmission electron microsco...The effects of heat treatment process on microstrucature, micro-yield strength and dynamic dimensional stability of ZL114A aluminum alloy were investigated by optical microscopy （OM）, transmission electron microscopy （TEM）, tensile testing and thermal cycling on-line measuring method. Fine dispersed eutectic Si phases are observed, and long strip eutectic Si and massive primary Si phases decrease in ZL114A alloy after high-temperature and long-time solution treatment, which result in the increase of micro-plastic deformation resistance. With the increasing of aging temperature, aging precipitation behaviour of ZLll4A alloy transforms from precipitation of GP zone and fl＇ phases simultaneously at lower temperature to precipitation of stable Mg2Si phases at higher temperature. Because coherent strengthening is the main strengthen mechanism for micro-plastic deformation, precipitation of stable Mg2Si phases is unfavorable to the improvement of micro-plastic deformation resistance. Micro-yield strength cannot characterize dimensional stability comprehensively, and dynamic dimensional stability under alternative temperature should also be tested cooperatively for better evaluation of dimensional stability.展开更多
In this paper we present a performance evaluation of thermal spraying coated hot forging dies conducted in a production line. The High Velocity Oxy-Fuel process was used for the deposition of a tungsten carbide coatin...In this paper we present a performance evaluation of thermal spraying coated hot forging dies conducted in a production line. The High Velocity Oxy-Fuel process was used for the deposition of a tungsten carbide coating, which is characterized by its optimal adherence and low porosity. A metallurgical characterization of the layer was previously done, in order to obtain reference information to assist in the interpretation of the practical tests results. The coated die allowed an increase in productivity of 37.5%, besides better dimensional stability results through the process and legibility of printed numbers.展开更多
This study has developed an efficient method to achieve excellent thermal dimensional stability and desired dimensions of hollow polyester fiber. Firstly,the influence of thermal treatment temperate( 140-180 ℃) on th...This study has developed an efficient method to achieve excellent thermal dimensional stability and desired dimensions of hollow polyester fiber. Firstly,the influence of thermal treatment temperate( 140-180 ℃) on the degree of shrinkage of fiber was investigated. The influence was also analyzed with a 2nd heating to simulate the application situation. It was discovered that the heat treatment at a temperature which was above the application temperature( 2nd heating) would efficiently remove the internal stress in the fiber and improve the thermal dimensional stability.Secondly,the impact of heat treatment temperature on the fiber diameter and the degree of hollowness were studied. The results implied that with a fixed fiber length, higher treatment temperature led to thinner fiber and a lower degree of hollowness.Last but not least,key parameters that could further influence the fiber dimensions were investigated. The results suggested that the fiber diameters and the degree of hollowness could be further controlled by tuning the drawing speed,the spinning meter pump output and cooling status while the spinneret parameters were fixed.展开更多
文摘Efficient use of timber is a vital concern problem, especially in these regions where the forestry coverage ratio is decreasing. Studies on physical modification of wood have been taken more attention due to the increasing attentions on environmental protection. Thermal modification is emphasized and developed quickly in developing countries, especially in European countries. A large number of researches have been conducted and some industrial production plants have been built. This paper reviewed the history of heat treatment, exemplifies the industrial developments in several European countries, summarized the basic principle of heat treatment and describes the environmental characteristics. The properties of heat-treated wood and its usage are also summed up.
基金Project(20120023110011) supported by Doctoral Program of Higher Education of ChinaProjects(2009KH09,2009QH02) supported by the Fundamental Research Funds for the Central Universities of China
文摘A comparative study of the influence of elevated temperature on foam geopolymer using circulating fluidized bed combustion fly ash（CFA） was reported. Foam geopoymers were prepared with different amounts of foam agent and different Si O2/Al2O3 molar ratios of 3.1, 3.4, and 3.8. The mechanical, thermo-physical properties and microstructure of the foam geopolymers before and after exposure to elevated temperature of 800, 1000, and 1200 ℃ were investigated. The specimen with Si O2/Al2O3 molar ratio of 3.8 exhibits the highest compressive strength, better microstructure and dimension stability before and after firing. Carnegeite, nepheline, and zeolite crystalline phases appearing after exposure may contribute to the good post-exposure strength. Low weight foam geopolymer using CFA can increase strength and maintain higher stability as high as 1000 ℃.
基金the Hebei Key Research and Development Program,China(No.20374202D)the Hebei High Level Talent Team Building,China(No.205A1104H).
文摘Due to the oxygen storage and release properties,cerium zirconium mixed oxides are recognized as the key material in automotive three-way catalysts.To reveal the effects of co-precipitation temperature on structure,physical and chemical properties of multi-doped cerium zirconium mixed oxides,a series of La and Y doped cerium zirconium mixed oxides(CZLYs)were synthesized via a co-precipitation method,and the physical and chemical properties of CZLYs were systemically characterized by XRD,N_(2) adsorption−desorption,TEM,XPS,oxygen storage capacity(OSC)and hydrogen temperature programmed reduction(H_(2)-TPR).The results show that co-precipitation temperature is an important parameter to influence the crystal size,oxygen storage capacity and thermal stability of CZLYs.When the co-precipitation temperature was 60℃,the best redox properties and thermal stability of CZLYs were obtained.After thermal treatment at 1100℃for 10 h,the specific surface area and oxygen storage capacity of the corresponding aged sample were 15.42 m^(2)/g and 497.7μmol/g,respectively.In addition,a mechanism was proposed to reveal the effects of co-precipitation temperature on the structure and properties of CZLYs.
文摘The effects of heat treatment process on microstrucature, micro-yield strength and dynamic dimensional stability of ZL114A aluminum alloy were investigated by optical microscopy （OM）, transmission electron microscopy （TEM）, tensile testing and thermal cycling on-line measuring method. Fine dispersed eutectic Si phases are observed, and long strip eutectic Si and massive primary Si phases decrease in ZL114A alloy after high-temperature and long-time solution treatment, which result in the increase of micro-plastic deformation resistance. With the increasing of aging temperature, aging precipitation behaviour of ZLll4A alloy transforms from precipitation of GP zone and fl＇ phases simultaneously at lower temperature to precipitation of stable Mg2Si phases at higher temperature. Because coherent strengthening is the main strengthen mechanism for micro-plastic deformation, precipitation of stable Mg2Si phases is unfavorable to the improvement of micro-plastic deformation resistance. Micro-yield strength cannot characterize dimensional stability comprehensively, and dynamic dimensional stability under alternative temperature should also be tested cooperatively for better evaluation of dimensional stability.
文摘In this paper we present a performance evaluation of thermal spraying coated hot forging dies conducted in a production line. The High Velocity Oxy-Fuel process was used for the deposition of a tungsten carbide coating, which is characterized by its optimal adherence and low porosity. A metallurgical characterization of the layer was previously done, in order to obtain reference information to assist in the interpretation of the practical tests results. The coated die allowed an increase in productivity of 37.5%, besides better dimensional stability results through the process and legibility of printed numbers.
基金Innovation Fund Project of National Commercial Aircraft Manufacturing Engineering Research Center(No.SAM C14-JS-15-048)Natural Science Foundation of Shanghai,China(No.13ZR1400400)the Fundamental Research Funds for the Central Universities,China
文摘This study has developed an efficient method to achieve excellent thermal dimensional stability and desired dimensions of hollow polyester fiber. Firstly,the influence of thermal treatment temperate( 140-180 ℃) on the degree of shrinkage of fiber was investigated. The influence was also analyzed with a 2nd heating to simulate the application situation. It was discovered that the heat treatment at a temperature which was above the application temperature( 2nd heating) would efficiently remove the internal stress in the fiber and improve the thermal dimensional stability.Secondly,the impact of heat treatment temperature on the fiber diameter and the degree of hollowness were studied. The results implied that with a fixed fiber length, higher treatment temperature led to thinner fiber and a lower degree of hollowness.Last but not least,key parameters that could further influence the fiber dimensions were investigated. The results suggested that the fiber diameters and the degree of hollowness could be further controlled by tuning the drawing speed,the spinning meter pump output and cooling status while the spinneret parameters were fixed.
