To improve the poor stability of casting process of Al alloy with high Mg content, which leads to poor final product quality, the melting purification process and the influences of the refiner on the microstructure an...To improve the poor stability of casting process of Al alloy with high Mg content, which leads to poor final product quality, the melting purification process and the influences of the refiner on the microstructure and defect of 5083 alloy were studied. The results show that the optimized process for the rotary impeller degassing of 5083 alloy is as follows： a rotary speed of 250-400 r/min; a gas flow of 1.2-2.0 L/s, a refining time of 10-15 min. This optimized process can reduce the gas content in the solid alloy to 2× 10^-3 mL/g or lower. Due to the addition of grain refiner, the cast microstructure of 5083 alloy is refined. The Al-5Ti-IB wire shows the best refining effect among all the refiners. The refining effect is improved with the increase of grain refiner addition amount. And the refinement effects become stable when Ti content reaches 0.1% or higher. The surface crinkling defect of the billet can be easily found in the alloy refined with Al-5Ti-IB wire compared with the alloys refined with other refiners.展开更多
Two additives of ethylene diamine tetraacetic acid （EDTA） and ammonium chloride （NH4C1） were separately used in the electrodeposition of Zn-Ni alloy films from a deep eutectic solvent. The effects of these two add...Two additives of ethylene diamine tetraacetic acid （EDTA） and ammonium chloride （NH4C1） were separately used in the electrodeposition of Zn-Ni alloy films from a deep eutectic solvent. The effects of these two additives on electrodeposition behavior, composition, morphology, and corrosion performance of the Zn-Ni alloys were investigated. The electrodeposition behaviors of Zn-Ni alloy revealed by the cyclic voltammetry show that the addition of EDTA to the Zn-Ni electrolyte enhances the Zn incorporation into the alloy film while the addition of NH4C1 produces an opposite effect by suppressing Zn incorporation into the film. With an increase of EDTA concentration in the electrolyte, the Zn content of the Zn-Ni films increases, while the grain size of the deposits and the current efficiency of the plating process decrease. The increase of NH4C1 concentration in the electrolyte would significantly refine the grain size of the electrodeposited Zn-Ni films, reduce the Zn content and increase the cathodic current efficiency. The corrosion testing indicates that the barrier corrosion resistances of Zn-Ni films electrodeposited from NHnC1 containing electrolytes are superior to those electrodeposited from EDTA-containing electrolytes, which in turn are superior to those electrodeposited from additive-free electrolytes.展开更多
The effects of non-flux purification techniques on the mechanical properties and microstructure of AZ91 magnesium alloy were investigated by ICP,OM,XRD and SEM.The results show that Ar spraying with high flow rate cou...The effects of non-flux purification techniques on the mechanical properties and microstructure of AZ91 magnesium alloy were investigated by ICP,OM,XRD and SEM.The results show that Ar spraying with high flow rate could remove non-metallic inclusions and improve the mechanical properties of AZ91.The alloy obtains the best properties after argon spraying for 30 min at the melt temperature of 740 °C.The ceramic foam filter(CFF) could effectively improve the ultimate tensile strength and elongation of AZ91 alloy,especially the elongation,which increase with increasing pores per inch(ppi) and the thickness of CFF.Non-flux purification does not change the microstructure of AZ91 alloy.However,filtration has a certain effect on the fracture pattern of AZ91 alloy.To improve the mechanical properties effectively,both filtration and gas spraying should be utilized together.展开更多
Deep eutectic solvents(DESs) are a kind of potential lixiviant for selective metal processing due to their versatile complexation properties. In this study, we investigated the recovery of zinc from zinc oxide dust us...Deep eutectic solvents(DESs) are a kind of potential lixiviant for selective metal processing due to their versatile complexation properties. In this study, we investigated the recovery of zinc from zinc oxide dust using choline chloride-ureaethylene glycol(ChCl-urea-EG) DESs. The zinc extraction efficiency can be up to 85.2% when the slurry concentration is 50 g/L, leaching temperature is 80 °C and stirring speed is 600 r/min. The leaching process is controlled by the diffusion and the corresponding activation energy is 32.1 k J/mol. The resultant solution was directly used for the electrodeposition of zinc. The pure zinc deposit is obtained with a current efficiency of 82.6%. Furthermore, the ChCl-urea-EG DESs can be recycled. This approach is shown to be promising for the recycling of zinc from the zinc-containing dust.展开更多
A three dimension of dynamic mathematical model of the molten carbonate fuel cell is established,in which the heat generation, mass transfer and electrochemical characteristics are described. The performance of the fu...A three dimension of dynamic mathematical model of the molten carbonate fuel cell is established,in which the heat generation, mass transfer and electrochemical characteristics are described. The performance of the fuel cell including the distributions of the temperature and the velocity is predicted numerically. Then the experimental data including the output performance of the fuel cell generation system and the temperature distributions are compared. The numerical results are in agreement with the experiment results.展开更多
A novel melting-assisted solvent-free route using solid oxalic acid was proposed for the post-treatment of SAPO-11 zeolite,followed by loading with 0.5 wt%Pt by the incipient wetness impregnation method.Subsequently,t...A novel melting-assisted solvent-free route using solid oxalic acid was proposed for the post-treatment of SAPO-11 zeolite,followed by loading with 0.5 wt%Pt by the incipient wetness impregnation method.Subsequently,the performance of the obtained bifunctional catalysts toward the hydroisomerization of n-dodecane was examined.The prepared samples were characterized by XRD,SEM,BET,XRF,Py-IR,and solid-state NMR.From the results,it was found that the high crystallinity and uniform morphology were retained after the post-treatment and that more(002)crystal faces were exposed,which was beneficial since more acid sites were provided.More importantly,the total Bronsted acid sites and the ratio(Ra)of the micropore area to the total surface area were optimized by this method.Thus,the catalytic performance was enhanced significantly,and the prepared Pt-SAPO-11-10%catalyst had the highest i-dodecane yield of 80.1%compared to 55.3%of Pt-SAPO-11.Expectedly,this facile and cost-effective method is promising for the hydroisomerization of normal paraffin in the production of lubricant base oils.展开更多
The main objective of this work was to use reline deep eutectic solvent,containing Al(III)ions,for the electrochemical study of the nucleation and growth of aluminum onto a glassy carbon electrode at different tempera...The main objective of this work was to use reline deep eutectic solvent,containing Al(III)ions,for the electrochemical study of the nucleation and growth of aluminum onto a glassy carbon electrode at different temperatures and angular speeds(ω)of the working electrode.In order to fulfill this,electrochemical and surface characterization techniques were used.It was found that as temperature increased,the onset of the Al(III)DES reduction occurred at less negative potentials while the current peak of the voltammograms increased.These indicate that Al deposition thermodynamics and kinetics were favored.Practically,no anodic current was detected due to Al passivation by Al(OH)_(3)(s)andγ-Al_(2)O_(3)(s).Atω=0 r/min,the Al deposition chronoamperograms were analyzed by a theoretical model comprising Al 3D diffusion-controlled nucleation and growth and residual water reduction.However,those recorded at different angular speeds were analyzed with a theoretical model where adsorption−desorption and diffusion-controlled nucleation−growth occurred simultaneously.The deposits were characterized by SEM,EDX,XPS and XRD.Atω=0 r/min,formation of well distributed nanoparticles((78.1±9.5)nm)was observed,while atω=900 r/min the deposit was formed by multiple 10μm diameter leaf-like flat microstructures,composed by Al,Al(OH)_(3)(s)andγ-A2O3(s).展开更多
In this study, a novel bio-based thermosetting system has been developed from epoxy resin （EP）, with rosin-sourced anhydrides （maleopimaric acid, RAM） as curing agent and imidazole type latent catalyst （two amino...In this study, a novel bio-based thermosetting system has been developed from epoxy resin （EP）, with rosin-sourced anhydrides （maleopimaric acid, RAM） as curing agent and imidazole type latent catalyst （two amino imidazole salt complex, IMA）, to be used as matrix for hot-melt prepreg curing at mid-temperature. For comparison, the epoxy resin system with petroleum sourced hardener methylhexahydrophthalicanhydride （MHHPA） was also examined. The curing behaviour and mechanism were investigated by non-isothermal differential scanning calorimeter （DSC） analysis and Fourier transform infrared （FTIR） spectra. The results showed that the curing course of bio-based epoxy resin system containing RAM included two stages, which were the reaction between the free carboxyl group of RAM and oxirane ring under the acceleration of IMA, and the main reaction attributed to the reaction between anhydride and oxirane. According to Kissinger method, the reaction activation energy （E,） of two stages were 68.9 and 86.5kJmo1-1, respectively. The Eo of EP/MHHPA and EP/IMA resin system were 81.04 and 77.9kJmol-I. The processing property of EP/RAM/IMA system, i.e. the relationship between viscosity-temperature-time, was characterized by cone-plate viscometer aim to decide the processing parameter ofprepreg preparation. The effect of RAM content on mechanical performance and dynamic mechanical property was investigated. Noteworthily, compared with the laminates with EP/MHHPA as matrix, the laminates with RAM as hardeners achieved a 44%, 73% and 70℃ increase in bending strength, bending modulus and the glass transition temperature, respectively, due to the bulky hydrogenated phenanthrene ring structure incorporated into the cross-linking networks. When the fiber volume fraction reached 47%, the mechanical property of the laminates prepared with hot melt prepreg was superior or comparable to that of composites with pure petroleum sourced matrix. RAM as cross-linking agent of epoxy resin holds a great potential to satisfy the requirement of composites such as structure and secondary structure parts preparation.展开更多
基金Project(12511075)supported by the Foundation of Heilongjiang Education Committee,China
文摘To improve the poor stability of casting process of Al alloy with high Mg content, which leads to poor final product quality, the melting purification process and the influences of the refiner on the microstructure and defect of 5083 alloy were studied. The results show that the optimized process for the rotary impeller degassing of 5083 alloy is as follows： a rotary speed of 250-400 r/min; a gas flow of 1.2-2.0 L/s, a refining time of 10-15 min. This optimized process can reduce the gas content in the solid alloy to 2× 10^-3 mL/g or lower. Due to the addition of grain refiner, the cast microstructure of 5083 alloy is refined. The Al-5Ti-IB wire shows the best refining effect among all the refiners. The refining effect is improved with the increase of grain refiner addition amount. And the refinement effects become stable when Ti content reaches 0.1% or higher. The surface crinkling defect of the billet can be easily found in the alloy refined with Al-5Ti-IB wire compared with the alloys refined with other refiners.
基金Projects(51271169,51001089) supported by the National Natural Science Foundation of China
文摘Two additives of ethylene diamine tetraacetic acid （EDTA） and ammonium chloride （NH4C1） were separately used in the electrodeposition of Zn-Ni alloy films from a deep eutectic solvent. The effects of these two additives on electrodeposition behavior, composition, morphology, and corrosion performance of the Zn-Ni alloys were investigated. The electrodeposition behaviors of Zn-Ni alloy revealed by the cyclic voltammetry show that the addition of EDTA to the Zn-Ni electrolyte enhances the Zn incorporation into the alloy film while the addition of NH4C1 produces an opposite effect by suppressing Zn incorporation into the film. With an increase of EDTA concentration in the electrolyte, the Zn content of the Zn-Ni films increases, while the grain size of the deposits and the current efficiency of the plating process decrease. The increase of NH4C1 concentration in the electrolyte would significantly refine the grain size of the electrodeposited Zn-Ni films, reduce the Zn content and increase the cathodic current efficiency. The corrosion testing indicates that the barrier corrosion resistances of Zn-Ni films electrodeposited from NHnC1 containing electrolytes are superior to those electrodeposited from EDTA-containing electrolytes, which in turn are superior to those electrodeposited from additive-free electrolytes.
基金Project(08XD14020) supported by the Program of Shanghai Subject Chief Scientist,ChinaProject(2007CB613701) supported by the National Basic Research Program of ChinaProject(2009AA033501) supported by the National High-tech Research and Development Program of China
文摘The effects of non-flux purification techniques on the mechanical properties and microstructure of AZ91 magnesium alloy were investigated by ICP,OM,XRD and SEM.The results show that Ar spraying with high flow rate could remove non-metallic inclusions and improve the mechanical properties of AZ91.The alloy obtains the best properties after argon spraying for 30 min at the melt temperature of 740 °C.The ceramic foam filter(CFF) could effectively improve the ultimate tensile strength and elongation of AZ91 alloy,especially the elongation,which increase with increasing pores per inch(ppi) and the thickness of CFF.Non-flux purification does not change the microstructure of AZ91 alloy.However,filtration has a certain effect on the fracture pattern of AZ91 alloy.To improve the mechanical properties effectively,both filtration and gas spraying should be utilized together.
基金Project(51764027) supported by the National Natural Science Foundation of ChinaProject(2014CB643404) supported by the National Basic Research Program of China
文摘Deep eutectic solvents(DESs) are a kind of potential lixiviant for selective metal processing due to their versatile complexation properties. In this study, we investigated the recovery of zinc from zinc oxide dust using choline chloride-ureaethylene glycol(ChCl-urea-EG) DESs. The zinc extraction efficiency can be up to 85.2% when the slurry concentration is 50 g/L, leaching temperature is 80 °C and stirring speed is 600 r/min. The leaching process is controlled by the diffusion and the corresponding activation energy is 32.1 k J/mol. The resultant solution was directly used for the electrodeposition of zinc. The pure zinc deposit is obtained with a current efficiency of 82.6%. Furthermore, the ChCl-urea-EG DESs can be recycled. This approach is shown to be promising for the recycling of zinc from the zinc-containing dust.
基金Supported by Shanghai Science and Technology Development (No. 993012003) and the National Natural Science Foundation of China (No.50206012).
文摘A three dimension of dynamic mathematical model of the molten carbonate fuel cell is established,in which the heat generation, mass transfer and electrochemical characteristics are described. The performance of the fuel cell including the distributions of the temperature and the velocity is predicted numerically. Then the experimental data including the output performance of the fuel cell generation system and the temperature distributions are compared. The numerical results are in agreement with the experiment results.
基金supported by the National Natural Science Foundation of China(21776295)the Youth Innovation Promotion Association,CAS(2017355)~~
文摘A novel melting-assisted solvent-free route using solid oxalic acid was proposed for the post-treatment of SAPO-11 zeolite,followed by loading with 0.5 wt%Pt by the incipient wetness impregnation method.Subsequently,the performance of the obtained bifunctional catalysts toward the hydroisomerization of n-dodecane was examined.The prepared samples were characterized by XRD,SEM,BET,XRF,Py-IR,and solid-state NMR.From the results,it was found that the high crystallinity and uniform morphology were retained after the post-treatment and that more(002)crystal faces were exposed,which was beneficial since more acid sites were provided.More importantly,the total Bronsted acid sites and the ratio(Ra)of the micropore area to the total surface area were optimized by this method.Thus,the catalytic performance was enhanced significantly,and the prepared Pt-SAPO-11-10%catalyst had the highest i-dodecane yield of 80.1%compared to 55.3%of Pt-SAPO-11.Expectedly,this facile and cost-effective method is promising for the hydroisomerization of normal paraffin in the production of lubricant base oils.
基金CONACyT for the scholarship granted to pursue postgraduate studiesCONACyT for Project 258487CONACyT for the support given to undertake a postdoctoral stay through Project 258487。
文摘The main objective of this work was to use reline deep eutectic solvent,containing Al(III)ions,for the electrochemical study of the nucleation and growth of aluminum onto a glassy carbon electrode at different temperatures and angular speeds(ω)of the working electrode.In order to fulfill this,electrochemical and surface characterization techniques were used.It was found that as temperature increased,the onset of the Al(III)DES reduction occurred at less negative potentials while the current peak of the voltammograms increased.These indicate that Al deposition thermodynamics and kinetics were favored.Practically,no anodic current was detected due to Al passivation by Al(OH)_(3)(s)andγ-Al_(2)O_(3)(s).Atω=0 r/min,the Al deposition chronoamperograms were analyzed by a theoretical model comprising Al 3D diffusion-controlled nucleation and growth and residual water reduction.However,those recorded at different angular speeds were analyzed with a theoretical model where adsorption−desorption and diffusion-controlled nucleation−growth occurred simultaneously.The deposits were characterized by SEM,EDX,XPS and XRD.Atω=0 r/min,formation of well distributed nanoparticles((78.1±9.5)nm)was observed,while atω=900 r/min the deposit was formed by multiple 10μm diameter leaf-like flat microstructures,composed by Al,Al(OH)_(3)(s)andγ-A2O3(s).
基金supported by the China-EU co-funded project ECO-COMPASS(Grant No.MJ2015-HG-103)
文摘In this study, a novel bio-based thermosetting system has been developed from epoxy resin （EP）, with rosin-sourced anhydrides （maleopimaric acid, RAM） as curing agent and imidazole type latent catalyst （two amino imidazole salt complex, IMA）, to be used as matrix for hot-melt prepreg curing at mid-temperature. For comparison, the epoxy resin system with petroleum sourced hardener methylhexahydrophthalicanhydride （MHHPA） was also examined. The curing behaviour and mechanism were investigated by non-isothermal differential scanning calorimeter （DSC） analysis and Fourier transform infrared （FTIR） spectra. The results showed that the curing course of bio-based epoxy resin system containing RAM included two stages, which were the reaction between the free carboxyl group of RAM and oxirane ring under the acceleration of IMA, and the main reaction attributed to the reaction between anhydride and oxirane. According to Kissinger method, the reaction activation energy （E,） of two stages were 68.9 and 86.5kJmo1-1, respectively. The Eo of EP/MHHPA and EP/IMA resin system were 81.04 and 77.9kJmol-I. The processing property of EP/RAM/IMA system, i.e. the relationship between viscosity-temperature-time, was characterized by cone-plate viscometer aim to decide the processing parameter ofprepreg preparation. The effect of RAM content on mechanical performance and dynamic mechanical property was investigated. Noteworthily, compared with the laminates with EP/MHHPA as matrix, the laminates with RAM as hardeners achieved a 44%, 73% and 70℃ increase in bending strength, bending modulus and the glass transition temperature, respectively, due to the bulky hydrogenated phenanthrene ring structure incorporated into the cross-linking networks. When the fiber volume fraction reached 47%, the mechanical property of the laminates prepared with hot melt prepreg was superior or comparable to that of composites with pure petroleum sourced matrix. RAM as cross-linking agent of epoxy resin holds a great potential to satisfy the requirement of composites such as structure and secondary structure parts preparation.
