A method, the morphology of screen printed carbon nanotube pastes is modified using a hard hairbrush, is presented. In this way, the organic matrix material is preferentially removed. Compared to those untreated films...A method, the morphology of screen printed carbon nanotube pastes is modified using a hard hairbrush, is presented. In this way, the organic matrix material is preferentially removed. Compared to those untreated films, the turn-on electric field of the treated film decreases from 2.2V/μm to 1.6V/μm, while the total emission current of the treated increases from 0.6mA/cm2 to 3mA/cm2, and uniform emission site density image has also been observed.展开更多
A mechanical separation process was developed for recovering metals from printed circuit board(PCB) scrap;it included three steps:impact crushing,sieving and fluidization separation.The mechanism of the technique was ...A mechanical separation process was developed for recovering metals from printed circuit board(PCB) scrap;it included three steps:impact crushing,sieving and fluidization separation.The mechanism of the technique was based on the difference in the crushabilities of metallic and nonmetallic materials in the PCBs that led to the concentrated distribution of metals in particles of larger sizes and nonmetals mostly in particles of smaller sizes.It was found that crushed PCB particles from 0.125 mm to 1.000 mm contained about 80% of metals in the PCBs.Metals acquired satisfactory liberation in particles smaller than 0.800 mm.The crushed PCB particles were sieved into fractions of different size ranges.Each fraction separately went through a gas-solid fluidized bed operating at a selected optimal gas velocity for the specific size range.Approximately 95% of metals in printed circuit board particles from 0.125 mm to 0.800 mm was recovered by the gas-fluidized bed separator at the selected optimal gas velocity.However,separation of metals from particles smaller than 0.125 mm was not satisfactory.Further study is needed on metal recovery from fine particles.展开更多
In this paper, the silver nanoparticle ink and ink-jet printing technology are used to manufacture the surface acoustic wave(SAW) filters. The characteristics of three common substrate piezoelectric materials of ST-qu...In this paper, the silver nanoparticle ink and ink-jet printing technology are used to manufacture the surface acoustic wave(SAW) filters. The characteristics of three common substrate piezoelectric materials of ST-quartz, Y36°-LiTaO3 and Y128°-LiNbO3 are evaluated. The experimental results show that Y128°-LiNbO3 matches the ink much better than others. The printed SAW filter with Y128°-LiNbO3 as piezoelectric substrate is realized, and its center frequency and bandwidth are 18.4 MHz and 500 kHz, respectively.展开更多
文摘A method, the morphology of screen printed carbon nanotube pastes is modified using a hard hairbrush, is presented. In this way, the organic matrix material is preferentially removed. Compared to those untreated films, the turn-on electric field of the treated film decreases from 2.2V/μm to 1.6V/μm, while the total emission current of the treated increases from 0.6mA/cm2 to 3mA/cm2, and uniform emission site density image has also been observed.
基金the Shanghai EXPO Special Project from the Ministry of Science and Technology of China under the Grant No. 2004BA908B02
文摘A mechanical separation process was developed for recovering metals from printed circuit board(PCB) scrap;it included three steps:impact crushing,sieving and fluidization separation.The mechanism of the technique was based on the difference in the crushabilities of metallic and nonmetallic materials in the PCBs that led to the concentrated distribution of metals in particles of larger sizes and nonmetals mostly in particles of smaller sizes.It was found that crushed PCB particles from 0.125 mm to 1.000 mm contained about 80% of metals in the PCBs.Metals acquired satisfactory liberation in particles smaller than 0.800 mm.The crushed PCB particles were sieved into fractions of different size ranges.Each fraction separately went through a gas-solid fluidized bed operating at a selected optimal gas velocity for the specific size range.Approximately 95% of metals in printed circuit board particles from 0.125 mm to 0.800 mm was recovered by the gas-fluidized bed separator at the selected optimal gas velocity.However,separation of metals from particles smaller than 0.125 mm was not satisfactory.Further study is needed on metal recovery from fine particles.
基金supported by the Project of the Science&Technology Pillar Program of Tianjin(No.12ZCZDJC35500)the Natural Science Foundation of Tianjin(No.13JCQNJC01300)
文摘In this paper, the silver nanoparticle ink and ink-jet printing technology are used to manufacture the surface acoustic wave(SAW) filters. The characteristics of three common substrate piezoelectric materials of ST-quartz, Y36°-LiTaO3 and Y128°-LiNbO3 are evaluated. The experimental results show that Y128°-LiNbO3 matches the ink much better than others. The printed SAW filter with Y128°-LiNbO3 as piezoelectric substrate is realized, and its center frequency and bandwidth are 18.4 MHz and 500 kHz, respectively.
