A self-ordered porous film was fabricated on aluminum alloy in a ternary boric-sulfuric-oxalic acid electrolyte system. By means of voltage–time response, the oxidation process as well as the growth efficiency was st...A self-ordered porous film was fabricated on aluminum alloy in a ternary boric-sulfuric-oxalic acid electrolyte system. By means of voltage–time response, the oxidation process as well as the growth efficiency was studied. Field emission scanning electron microscopy（FE-SEM） was adopted to reveal the morphological and microstructural features of as-fabricated oxide layers. The corrosion protection properties of the films were investigated by electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The results showed that increasing the concentration of the double ionic layer located at the oxide interface could accelerate the film growth rate. The anodic oxidative layer with thickness of 8-9 μm and pore diameter of 10-14 nm maintains the pattern and topography of workpieces, compared with the overall closed film with hierarchical structure. Both samples exhibited much lower corrosion current density after boil water sealing. Meanwhile, a superior stability could be achieved through raising the ambient temperature.展开更多
Microstructural characteristics and mechanical behavior of hot extruded Al5083/B4C nanocomposites were studied.Al5083and Al5083/B4C powders were milled for50h under argon atmosphere in attrition mill with rotational s...Microstructural characteristics and mechanical behavior of hot extruded Al5083/B4C nanocomposites were studied.Al5083and Al5083/B4C powders were milled for50h under argon atmosphere in attrition mill with rotational speed of400r/min.For increasing the elongation,milled powders were mixed with30%and50%unmilled aluminum powder(mass fraction)with meanparticle size of>100μm and<100μm and then consolidated by hot pressing and hot extrusion with9:1extrusion ratio.Hot extrudedsamples were studied by optical microscopy,scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),transmission electron microscopy(TEM),tensile and hardness tests.The results showed that mechanical milling process andpresence of B4C particles increase the yield strength of Al5083alloy from130to566MPa but strongly decrease elongation(from11.3%to0.49%).Adding<100μm unmilled particles enhanced the ductility and reduced tensile strength and hardness,but usingthe>100μm unmilled particles reduced the tensile strength and ductility at the same time.By increasing the content of unmilledparticles failure mechanism changed from brittle to ductile.展开更多
5083 Al alloy sheets with different grain sizes(8.7-79.2 μm) were obtained by cold rolling and annealing. Their microstructures, intergranular corrosion(IGC), stress corrosion cracking(SCC), and crack propagation beh...5083 Al alloy sheets with different grain sizes(8.7-79.2 μm) were obtained by cold rolling and annealing. Their microstructures, intergranular corrosion(IGC), stress corrosion cracking(SCC), and crack propagation behaviors were investigated. The results showed that samples with coarse grains exhibit better IGC resistance with a corrosion depth of 15 μm. The slow strain rate test results revealed that fine-grained samples exhibit better SCC resistance with a susceptibility index(ISSRT) of 11.2%. Furthermore, based on the crack propagation mechanism, grain refinement can improve the SCC resistance by increasing the number of grain boundaries to induce the corrosion crack propagation along a tortuous path. The grains with {011} orientation could hinder crack propagation by orientating it toward the low-angle grain boundary region. The crack in the fine-grained material slowly propagates due to the tortuous path, and low H;and Cl;concentrations.展开更多
Marine corrosion and biofouling seriously affect the service life of marine structural materials,resulting in performance failure,enormous economic loss,and even catastrophic safety accidents.It is worthwhile and desi...Marine corrosion and biofouling seriously affect the service life of marine structural materials,resulting in performance failure,enormous economic loss,and even catastrophic safety accidents.It is worthwhile and desirable to develop high-efficiency strategy for anti-corrosion and anti-biofouling.In this paper,superhydrophobic 5083 aluminum alloy(AA5083)surface with micro-nano hierarchical morphology was fabricated through anodization followed by 1H,1H,2H,2H-perfluorooctyltriethoxysilane(POTS)modification.The surface morphologies,roughness,and chemical compositions were revealed by scanning electron microscopy,atomic force microscopy,and X-ray diffraction.The self-cleaning ability,corrosion resistance and algae adhesion suppression ability of the fabricated surfaces were investigated,indicating an excellent water-proofing,anti-corrosion and anti-biofouling performance.We believe the superhydrophobic creation of metallic materials is expected to have potential applications in marine corrosion and antibiofouling fields.展开更多
In this research, EIS （electrochemical impedance spectroscopy） technique was utilized to study the pitting corrosion behaviour of AA5083-H321 aluminum-magnesium alloy in 3.5% NaCl solution. Impedance spectra were ob...In this research, EIS （electrochemical impedance spectroscopy） technique was utilized to study the pitting corrosion behaviour of AA5083-H321 aluminum-magnesium alloy in 3.5% NaCl solution. Impedance spectra were obtained during 240 h of exposure of the sample to the test solution. The surface and cross-section of the samples were studied by scanning electron microscopy （SEM） and EDAX （energy dispersive analysis of X-ray） analysis. The results indicated that as the resistance of the passive layer on intermetallic particles is very small, this parameter on the sample surface layers is controlled by that of pure passive layer. However, the capacitors in the proposed equivalent circuit are replaced with the constant phase elements （CPE）, due to non-uniformity and occurrence of pitting corrosion on the surface. The outward diffusion of Al^＋3 ions through the passive layer and the thickening of this layer cause the impedance decrease in the first 24 h and increase afterwards. The detachment of intermetallic particles from some of pits and the accumulation of the corrosion products inside some others are factors that prevents the continuation of cathodic reactions on the top of the intermetallic particles.展开更多
Flow-induced corrosion consists electrochemical and mechanical components. The present paper has to assessed the role of chloride ion and dissolved oxygen in the electrochemical component of flow induced corrosion for...Flow-induced corrosion consists electrochemical and mechanical components. The present paper has to assessed the role of chloride ion and dissolved oxygen in the electrochemical component of flow induced corrosion for AA5083-H321 aluminum-magnesium alloy which is extensively used in the construction of high-speed boats, submarines, hovercrafts, and desalination systems, in NaCI solutions. Electrochemical tests were carried out at flow velocities of 0, ：2, 5, 7 and 10 m/s, in aerated and deaerated NaCI solutions with different sodium chloride concentrations. The results showed that the high rate of oxygen reduction under hydrodynamic conditions causes an increase in the density of pits on the surface. The increase of chloride ions concentration under flow conditions accelerates the rate of anodic reactions, but have no influence on the cathodic reactions. Thus, in the current work, it was found that under flow conditions, due to the elimination of corrosion products inside the pits, corrosion resistance of the alloy is increased.展开更多
As a material with good corrosion resistance,5083 aluminum alloy has a great application prospect in marine environment.In this work,the corrosion characteristics of 5083 aluminum alloy in seawater containing phosphat...As a material with good corrosion resistance,5083 aluminum alloy has a great application prospect in marine environment.In this work,the corrosion characteristics of 5083 aluminum alloy in seawater containing phosphate were investigated with Potentiodynamic Polarization,Electrochemical Impedance Spectroscopy (EIS),Scanning Electron Microscope (SEM),Energy Dispersive Spectroscopy Analysis (EDSA),X-ray Photoelectron Spectroscopy (XPS) and Laser Confocal Microscope.The results indicated that the effects of phosphate in seawater were two-fold.Firstly,phosphate slightly accelerated the corrosion of 5083 in seawater in the early stage of corrosion.HPO_4~(2-)competed with OH~-in the adsorption process on the alloy surface,which weakened the contact between OH~-and Al~(3+)near the interface of the alloy,and inhibited the formation as well as the self-repair of the passive film,thus accelerating the activation dissolution process.Compared with the natural seawater,the charge transfer resistance of 5083 in the seawater containing phosphate decreased faster during the early stage of corrosion,and the corrosion current density i_(corr) was higher in seawater containing phosphate.On the other hand,the addition of phosphate would not affect the cluster distribution of the second phase of 5083 in seawater,but it changed the composition of the corrosion product layer and had an obvious inhibitory effect on the local corrosion of 5083 in seawater.After 16-day exposure,shallower and more sparsely distributed pits could be observed on the derusted surface of 5083 in the seawater containing phosphate,and the pitting coefficient in the seawater containing phosphate was significantly lower than that in natural seawater.The reduction of pitting tendency could be realized mainly through two ways.First,the HPO_4~(2-)adsorbed on the surface of the passive film in the early stage of corrosion and repeled the corrosive anions such as Cl~-.Second,phosphate participated in the construction of the Ca HPO_4 precipitation film,which acted as a barrier and protection.展开更多
Laser beam welding of aluminum alloys is expected to offer good mechanical properties of welded joints. In this experimental work reported, CO2 laser beam autogenoas welding and wire feed welding are conducted on 4 mm...Laser beam welding of aluminum alloys is expected to offer good mechanical properties of welded joints. In this experimental work reported, CO2 laser beam autogenoas welding and wire feed welding are conducted on 4 mm thick 5083- H321 aluminum alloy sheets at different welding variables. The mechanical properties and microstructure characteristics of the welds are evaluated through tensile tests, micro-hardness tests, optical microscopy and scanning electron microscopy （SEM）. Experimental results indicate that both the tensile strength and hardness of laser beam welds are affected by the constitution of filler material, except the yield strength. The soften region of laser beam welds is not in the heat-affected zone （ HAZ ）. The tensile fracture of laser beam welded specimens takes place in the weld zone and close to the weld boundary because of different filler materials. Some pores are found on the fracture face, including hydrogen porosities and blow holes, but these pores have no influence on the tensile strength of laser beam welds. Tensile strength values of laser beam welds with filler wire are up to 345.57 MPa, 93% of base material values, and yield strengths of laser beam welds are equivalent to those of base metal （264. 50 MPa）.展开更多
Dual equal channel lateral extrusion (DECLE), as a severe plastic deformation (SPD) process, was employed forimproving the mechanical properties of AA5083 aluminum alloy. Several experiments were conducted to study th...Dual equal channel lateral extrusion (DECLE), as a severe plastic deformation (SPD) process, was employed forimproving the mechanical properties of AA5083 aluminum alloy. Several experiments were conducted to study the influences of theroute type, namely A and B, and pass number on mechanical properties of the material. The process was conducted up to 6 passeswith decreasing process temperature, specifically from 573 to 473 K. Supplementary experiments involving metallography, hardnessand tensile tests were carried out in order to evaluate the effects of the process variables. The hardness measurements exhibitedreasonably uniform distributions within the product with a maximum increase of 64% via a 6-pass operation. The yield and ultimatestrengths also amended 107% and 46%, respectively. These significant improvements were attributed to the severe shear deformationof grains and decreasing pass temperature, which intensified the grain refinement. TEM images showed an average grain sizereduction from 100 μm for the annealed billet to 200 nm after 6 passes of DECLE. Finally, the experimental findings for routes A andB were compared and discussed and some important conclusions were drawn.展开更多
The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 1...The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 10^-4- 1.0× 10^-2 s^-1. The maximum elongation 530% of the fine-grained 5083 AI alloy was obtained at 550℃ and 4.17× 10^-4 s^-1. Fracture analysis by scanning electron microscopy （SEM） indicated that the formation of filament （formed by liquid phase） was greatly affected by the tensile temperature and strain rate. The results also showed that the optimum morphology of formed filament was obtained at 550℃ and a strain rate of 4.17× 10^-4 s^-1. The effect of liquid phase on superplastic deformation of the alloy was further discussed.展开更多
The microstructure evolution of the fine-grained 5083 Al alloy was investigated in annealing temperature range of 150−300℃.Then the effects of the different annealed microstructures on high-temperature deformation be...The microstructure evolution of the fine-grained 5083 Al alloy was investigated in annealing temperature range of 150−300℃.Then the effects of the different annealed microstructures on high-temperature deformation behavior were further studied.The results indicate that the initial recrystallization temperature is about 200℃.By tensile tests at 380−570℃and in strain rate range of 4.17×10^(−4)−1.0×10^(−2) s^(−1),the optimum superplastic parameters are obtained as follows:the annealed temperature 250℃,the tensile temperature 550℃and the strain rate 4.17×10^(−4) s^(−1).With the aid of scanning electronic microscopy(SEM),the fractography of the alloy after the superplastic deformation was analyzed.The results reveal that intergranular cavities with fine size and homogeneous distribution are beneficial to superplastic deformation.展开更多
The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average s...The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average size of 15 m and porosity in the range of 0.1 vol. % to 5vol. % . Two distinct TMP procedures are employed to close porosity and refine grain size:extrusion plus rolling and direct rolling. The material processed using the former method exhibits arelatively high superplasticity with a maximum superplastic elongation of 465 % , whereas thatprocessed using the latter method exhibits a maximum superplastic elongation of 295 % . Materialsprocessed using extrusion plus rolling and direct rolling both exhibit similar stress-strainbehavior and strain rate sensitivity factors. The strain rate factors are in the 0.3 to 0.5 range.The difference in their superplastic elongation is possibly the result of differences in grain sizeand available cavity nucleation sites provided by closed gas pores.展开更多
The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature ra...The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature range of 500-570 ℃ and a strain rate range of 4.17×10^-4 s-1^- 1×10^- 2 s^- 1. Maximum tensile elongation 530% was obtained at 550 ℃ and strain rate ε＆ =4 .17×10^-4 s^-1. Dislocations were observed in grain interiors and at grain boundaries during uniaxial tensile deformation by transmission electronic microscopy （TEM）, respectively. Results show that the grain boundary sliding （GBS） accommodated by dislocation motion is the principal reason for superplastic deformation. The cavities and fracture were observed during uniaxial tensile deformation of the alloy by scanning electronic microscopy （SEM）, indicating that linkage of cavities in large region would induce failure of the material. Moreover, presence of liquid phase at grain boundary also affects the superplastic deformation and behavior of cavities.展开更多
Laser-MIG hybrid welding process was dealt with 6 mm thick 5083Hl16 Al-Mg alloy plate in butt-joint configuration. Weld formation principle during hybrid welding was explained. The joint properties and microstructure ...Laser-MIG hybrid welding process was dealt with 6 mm thick 5083Hl16 Al-Mg alloy plate in butt-joint configuration. Weld formation principle during hybrid welding was explained. The joint properties and microstructure characteristics of welded joints were analyzed by tensile tests, fractographs observed by optical microscopy and scanning electron microscopy （SEM）. Higher heat input could obtain better mechanical properties, and tensile strength and elongation reached 97.2%, 81% of the base metal, respectively. Fracture position traasited from fusion line to weld center in the higher heat input, and fracture location were only in the center of welded joints for the heat input relatively small.展开更多
With the popularization of friction stir welding(FSW),5083-H321 and 6061-T6 aluminum alloy materials are widely used during the FSW process.In this study,the fatigue life of friction stir welding with two materials,i....With the popularization of friction stir welding(FSW),5083-H321 and 6061-T6 aluminum alloy materials are widely used during the FSW process.In this study,the fatigue life of friction stir welding with two materials,i.e.,5083-H321 and 6061-T6 aluminum alloy,are studied.Fatigue tests were carried out on the base metal of these two materials as well as on the butt joints and overlapping FSW samples.The principle of the equivalent structural stress method is used to analyze the FSW test data of these two materials.The fatigue resistances of these two materials were com-pared and a unified principal S-N curve equation was fitted.Two key parameters of the unified principal S-N curve obtained by fitting,Cd is 4222.5,and h is 0.2693.A new method for an FSW fatigue life assessment was developed in this study and can be used to calculate the fatigue life of different welding forms with a single S-N curve.Two main fatigue tests of bending and tension were used to verify the unified principal S-N curve equation.The results show that the fatigue life calculated by the unified mean 50%master S-N curve parameters are the closest to the fatigue test results.The reliability,practicability,and generality of the master S-N curve fitting parameters were verified using the test data.The unified principal S-N curve acquired in this study can not only be used in aluminum alloy materials but can also be applied to other materials.展开更多
Abstract： The superplastic response of commercial 5083 alloy （Al-4. 42Mg） under uniaxial tension at strain rates ranging from 5 × 10-5 to 10-2s -1 in the temperature interval 400 -550℃ was systematically stud...Abstract： The superplastic response of commercial 5083 alloy （Al-4. 42Mg） under uniaxial tension at strain rates ranging from 5 × 10-5 to 10-2s -1 in the temperature interval 400 -550℃ was systematically studied in this paper. The tension test was conducted on samples of rolling direction. The maximum elongation-to-failure of 486% was found at 500 % and strain rate of 10-4s-1. To identify the main characteristics of superplastic deformation and to determine the mechanism of superplastic deformation of the alloy, the microstructure and fracture of the alloy were analyzed as a function of strain, strain rate and temperature using optical microscopy （OM） and scanning electron microscopy （SEM）, the apparent strain rate sensitivity exponent ma and the apparent activation energy Qa were also studied. Based on the fracture analysis and the calculated data of m and Qa, it is suggested that the dominant deformation mechanism in the present alloy is grain boundary sliding （GBS） during the best deformation condition.展开更多
Thepurpose of the present paper is to study the mechanical propertiesand microstructureof the twin-roll cast and cold rolled AA5083 aluminum alloy sheet in strain-hardened H321 temper. To reach this goal, first, a sou...Thepurpose of the present paper is to study the mechanical propertiesand microstructureof the twin-roll cast and cold rolled AA5083 aluminum alloy sheet in strain-hardened H321 temper. To reach this goal, first, a sound surface slab of 8.90 mm thick and 1260 mm wide was cast by a 15°; tilt back twin roll caster at a casting speed of 490 mm/min. After homogenization at 520 ℃, the product was cold rolled to two thicknesses of 6.30 mm and 3.85 mm with an intermediate annealing at 370 ℃ and final stabilization at 180 ℃. Opticalmicroscopyand scanning electron microscopy （SEM） investigations of the as-cast state depicted the segregation of intermetallic particles mainly in grain boundaries which wasthe cause of grain removal observed in the fracture surface of tensile test samples. In addition, mechanical properties indicated an increase in total elongation after homogenization heat treatment dueto the elimination of the grain boundary segregations. Finally, it was observed that the properties of the 3.85 mmthick sheet were consistent with the H321 temper requirements according to ASTM B 290M standard due to applying sufficient cold reduction during cold rolling stage.展开更多
With no annealing treatment, cathodic polarization trends in 5083F A1 alloy revealed concentration polarization and activation polarization. However, the annealed specimens have lower current densities at corrosion pr...With no annealing treatment, cathodic polarization trends in 5083F A1 alloy revealed concentration polarization and activation polarization. However, the annealed specimens have lower current densities at corrosion protection potential compared to the non-annealed specimen. The results of SSRTs conducted in seawater at the applied potential range of-l.8 V to -0.5 V indicated that the maximum tensile strength, elongation, and time-to-fracture had high values at applied potentials of -0.7 to -1.4 V. The maximum tensile strength, elongation, and time-to-f？acture decreased when the potential values were beyond this range in either anodic or cathodic direction. In general, the increased shear lip caused by annealing treatment indicates elongation. Time-to-fracture would likely increase with elongation. Potentials between -0.5 V to -0.6 V were found to be in the region of stress corrosion cracking. The corrosion protection zone was determined to be -0.7 V to -J,4 V because these potential ranges produced good mechanical properties. Potential less than -1.4 V produced a fractured surface with a mixture of dimples （ductile fractures） and a quasi-cleavage pattern resulting from the effects of hydrogen gas.展开更多
To enhance the stress corrosion cracking(SCC)resistance,Zn was utilized as an alloy element to add in the AA5083 aluminum alloys.The effects of Zn content on the microstructures,mechanical properties and SCC resistanc...To enhance the stress corrosion cracking(SCC)resistance,Zn was utilized as an alloy element to add in the AA5083 aluminum alloys.The effects of Zn content on the microstructures,mechanical properties and SCC resistance were systematically evaluated.The results demonstrate that in the studied range adding Zn can significantly improve the SCC resistance of the AA5083 alloys.This is related to the relatively low amount of continuous β(Al3Mg2)phase along grain boundary and the formation of Zn-containing phase such as Al5Mg11Zn4 phase.Based on the results,the optimal Zn content with respect to SCC resistance is approximately 0.50 wt.%.Further increasing Zn content results in coarse precipitates discontinuously distributed along grain boundaries.展开更多
Aluminum alloy 5083(AA5083)processed by large-scale Equal-channel angular pressing(ECAP)is an excellent engineering material with great prospects for industrial applications.An accurate assessment of the underlying co...Aluminum alloy 5083(AA5083)processed by large-scale Equal-channel angular pressing(ECAP)is an excellent engineering material with great prospects for industrial applications.An accurate assessment of the underlying constitutive relationships with easily determined material constants is critical for the predictive design and informed processing of such structural materials.To develop such a design framework,uniaxial dynamic compressive tests over a wide range of temperatures(293-573 K)were carried out for an ECAP-processed AA5083 alloy.Additionally,the microstructure before and after dynamic loading was characterized by SEM and TEM.Based on the experimental results,a new dynamic constitutive model,based on thermal activation theory,was established to describe the plastic flow behavior of the AA5083 alloy that incorporates the effects of plastic strain,temperature,and strain rate.The input parameters of the new model were determined using a particle swarm optimization(PSO)method.The model predictions show excellent agreement with experimental results,which suggests that the current predictive constitutive model is highly effective in reproducing the dynamic deformation behavior of the large-scale ECAP-processed AA5083.展开更多
文摘A self-ordered porous film was fabricated on aluminum alloy in a ternary boric-sulfuric-oxalic acid electrolyte system. By means of voltage–time response, the oxidation process as well as the growth efficiency was studied. Field emission scanning electron microscopy（FE-SEM） was adopted to reveal the morphological and microstructural features of as-fabricated oxide layers. The corrosion protection properties of the films were investigated by electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The results showed that increasing the concentration of the double ionic layer located at the oxide interface could accelerate the film growth rate. The anodic oxidative layer with thickness of 8-9 μm and pore diameter of 10-14 nm maintains the pattern and topography of workpieces, compared with the overall closed film with hierarchical structure. Both samples exhibited much lower corrosion current density after boil water sealing. Meanwhile, a superior stability could be achieved through raising the ambient temperature.
文摘Microstructural characteristics and mechanical behavior of hot extruded Al5083/B4C nanocomposites were studied.Al5083and Al5083/B4C powders were milled for50h under argon atmosphere in attrition mill with rotational speed of400r/min.For increasing the elongation,milled powders were mixed with30%and50%unmilled aluminum powder(mass fraction)with meanparticle size of>100μm and<100μm and then consolidated by hot pressing and hot extrusion with9:1extrusion ratio.Hot extrudedsamples were studied by optical microscopy,scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),transmission electron microscopy(TEM),tensile and hardness tests.The results showed that mechanical milling process andpresence of B4C particles increase the yield strength of Al5083alloy from130to566MPa but strongly decrease elongation(from11.3%to0.49%).Adding<100μm unmilled particles enhanced the ductility and reduced tensile strength and hardness,but usingthe>100μm unmilled particles reduced the tensile strength and ductility at the same time.By increasing the content of unmilledparticles failure mechanism changed from brittle to ductile.
基金financial support and Program of the Ministry of Education in China (2011)。
文摘5083 Al alloy sheets with different grain sizes(8.7-79.2 μm) were obtained by cold rolling and annealing. Their microstructures, intergranular corrosion(IGC), stress corrosion cracking(SCC), and crack propagation behaviors were investigated. The results showed that samples with coarse grains exhibit better IGC resistance with a corrosion depth of 15 μm. The slow strain rate test results revealed that fine-grained samples exhibit better SCC resistance with a susceptibility index(ISSRT) of 11.2%. Furthermore, based on the crack propagation mechanism, grain refinement can improve the SCC resistance by increasing the number of grain boundaries to induce the corrosion crack propagation along a tortuous path. The grains with {011} orientation could hinder crack propagation by orientating it toward the low-angle grain boundary region. The crack in the fine-grained material slowly propagates due to the tortuous path, and low H;and Cl;concentrations.
基金the National Natural Science Foundation of China(Nos.41376003,41806089,41827805)the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDA13040405)。
文摘Marine corrosion and biofouling seriously affect the service life of marine structural materials,resulting in performance failure,enormous economic loss,and even catastrophic safety accidents.It is worthwhile and desirable to develop high-efficiency strategy for anti-corrosion and anti-biofouling.In this paper,superhydrophobic 5083 aluminum alloy(AA5083)surface with micro-nano hierarchical morphology was fabricated through anodization followed by 1H,1H,2H,2H-perfluorooctyltriethoxysilane(POTS)modification.The surface morphologies,roughness,and chemical compositions were revealed by scanning electron microscopy,atomic force microscopy,and X-ray diffraction.The self-cleaning ability,corrosion resistance and algae adhesion suppression ability of the fabricated surfaces were investigated,indicating an excellent water-proofing,anti-corrosion and anti-biofouling performance.We believe the superhydrophobic creation of metallic materials is expected to have potential applications in marine corrosion and antibiofouling fields.
文摘In this research, EIS （electrochemical impedance spectroscopy） technique was utilized to study the pitting corrosion behaviour of AA5083-H321 aluminum-magnesium alloy in 3.5% NaCl solution. Impedance spectra were obtained during 240 h of exposure of the sample to the test solution. The surface and cross-section of the samples were studied by scanning electron microscopy （SEM） and EDAX （energy dispersive analysis of X-ray） analysis. The results indicated that as the resistance of the passive layer on intermetallic particles is very small, this parameter on the sample surface layers is controlled by that of pure passive layer. However, the capacitors in the proposed equivalent circuit are replaced with the constant phase elements （CPE）, due to non-uniformity and occurrence of pitting corrosion on the surface. The outward diffusion of Al^＋3 ions through the passive layer and the thickening of this layer cause the impedance decrease in the first 24 h and increase afterwards. The detachment of intermetallic particles from some of pits and the accumulation of the corrosion products inside some others are factors that prevents the continuation of cathodic reactions on the top of the intermetallic particles.
文摘Flow-induced corrosion consists electrochemical and mechanical components. The present paper has to assessed the role of chloride ion and dissolved oxygen in the electrochemical component of flow induced corrosion for AA5083-H321 aluminum-magnesium alloy which is extensively used in the construction of high-speed boats, submarines, hovercrafts, and desalination systems, in NaCI solutions. Electrochemical tests were carried out at flow velocities of 0, ：2, 5, 7 and 10 m/s, in aerated and deaerated NaCI solutions with different sodium chloride concentrations. The results showed that the high rate of oxygen reduction under hydrodynamic conditions causes an increase in the density of pits on the surface. The increase of chloride ions concentration under flow conditions accelerates the rate of anodic reactions, but have no influence on the cathodic reactions. Thus, in the current work, it was found that under flow conditions, due to the elimination of corrosion products inside the pits, corrosion resistance of the alloy is increased.
基金supported by the National Natural Science Foundation of China (No. U1706221)。
文摘As a material with good corrosion resistance,5083 aluminum alloy has a great application prospect in marine environment.In this work,the corrosion characteristics of 5083 aluminum alloy in seawater containing phosphate were investigated with Potentiodynamic Polarization,Electrochemical Impedance Spectroscopy (EIS),Scanning Electron Microscope (SEM),Energy Dispersive Spectroscopy Analysis (EDSA),X-ray Photoelectron Spectroscopy (XPS) and Laser Confocal Microscope.The results indicated that the effects of phosphate in seawater were two-fold.Firstly,phosphate slightly accelerated the corrosion of 5083 in seawater in the early stage of corrosion.HPO_4~(2-)competed with OH~-in the adsorption process on the alloy surface,which weakened the contact between OH~-and Al~(3+)near the interface of the alloy,and inhibited the formation as well as the self-repair of the passive film,thus accelerating the activation dissolution process.Compared with the natural seawater,the charge transfer resistance of 5083 in the seawater containing phosphate decreased faster during the early stage of corrosion,and the corrosion current density i_(corr) was higher in seawater containing phosphate.On the other hand,the addition of phosphate would not affect the cluster distribution of the second phase of 5083 in seawater,but it changed the composition of the corrosion product layer and had an obvious inhibitory effect on the local corrosion of 5083 in seawater.After 16-day exposure,shallower and more sparsely distributed pits could be observed on the derusted surface of 5083 in the seawater containing phosphate,and the pitting coefficient in the seawater containing phosphate was significantly lower than that in natural seawater.The reduction of pitting tendency could be realized mainly through two ways.First,the HPO_4~(2-)adsorbed on the surface of the passive film in the early stage of corrosion and repeled the corrosive anions such as Cl~-.Second,phosphate participated in the construction of the Ca HPO_4 precipitation film,which acted as a barrier and protection.
基金This research was supported by Major Subject Foundation of Beijing University of Technology
文摘Laser beam welding of aluminum alloys is expected to offer good mechanical properties of welded joints. In this experimental work reported, CO2 laser beam autogenoas welding and wire feed welding are conducted on 4 mm thick 5083- H321 aluminum alloy sheets at different welding variables. The mechanical properties and microstructure characteristics of the welds are evaluated through tensile tests, micro-hardness tests, optical microscopy and scanning electron microscopy （SEM）. Experimental results indicate that both the tensile strength and hardness of laser beam welds are affected by the constitution of filler material, except the yield strength. The soften region of laser beam welds is not in the heat-affected zone （ HAZ ）. The tensile fracture of laser beam welded specimens takes place in the weld zone and close to the weld boundary because of different filler materials. Some pores are found on the fracture face, including hydrogen porosities and blow holes, but these pores have no influence on the tensile strength of laser beam welds. Tensile strength values of laser beam welds with filler wire are up to 345.57 MPa, 93% of base material values, and yield strengths of laser beam welds are equivalent to those of base metal （264. 50 MPa）.
基金partially supported by the Iran National Science Foundation(INSF) with grant number 92014140
文摘Dual equal channel lateral extrusion (DECLE), as a severe plastic deformation (SPD) process, was employed forimproving the mechanical properties of AA5083 aluminum alloy. Several experiments were conducted to study the influences of theroute type, namely A and B, and pass number on mechanical properties of the material. The process was conducted up to 6 passeswith decreasing process temperature, specifically from 573 to 473 K. Supplementary experiments involving metallography, hardnessand tensile tests were carried out in order to evaluate the effects of the process variables. The hardness measurements exhibitedreasonably uniform distributions within the product with a maximum increase of 64% via a 6-pass operation. The yield and ultimatestrengths also amended 107% and 46%, respectively. These significant improvements were attributed to the severe shear deformationof grains and decreasing pass temperature, which intensified the grain refinement. TEM images showed an average grain sizereduction from 100 μm for the annealed billet to 200 nm after 6 passes of DECLE. Finally, the experimental findings for routes A andB were compared and discussed and some important conclusions were drawn.
文摘The liquid phase behavior of the fine-grained 5083 AI alloy obtained through thermomechanical process was investigated during the tensile tests in a temperature range of 380-570℃ and strain rate range of 4.17× 10^-4- 1.0× 10^-2 s^-1. The maximum elongation 530% of the fine-grained 5083 AI alloy was obtained at 550℃ and 4.17× 10^-4 s^-1. Fracture analysis by scanning electron microscopy （SEM） indicated that the formation of filament （formed by liquid phase） was greatly affected by the tensile temperature and strain rate. The results also showed that the optimum morphology of formed filament was obtained at 550℃ and a strain rate of 4.17× 10^-4 s^-1. The effect of liquid phase on superplastic deformation of the alloy was further discussed.
文摘The microstructure evolution of the fine-grained 5083 Al alloy was investigated in annealing temperature range of 150−300℃.Then the effects of the different annealed microstructures on high-temperature deformation behavior were further studied.The results indicate that the initial recrystallization temperature is about 200℃.By tensile tests at 380−570℃and in strain rate range of 4.17×10^(−4)−1.0×10^(−2) s^(−1),the optimum superplastic parameters are obtained as follows:the annealed temperature 250℃,the tensile temperature 550℃and the strain rate 4.17×10^(−4) s^(−1).With the aid of scanning electronic microscopy(SEM),the fractography of the alloy after the superplastic deformation was analyzed.The results reveal that intergranular cavities with fine size and homogeneous distribution are beneficial to superplastic deformation.
文摘The superplasticity of spray deposited and thermomechanical processed 5083Al-Mg alloy is investigated in this paper. The results show that spray deposited 5083 Al exhibits anequiaxed grain morphology with an average size of 15 m and porosity in the range of 0.1 vol. % to 5vol. % . Two distinct TMP procedures are employed to close porosity and refine grain size:extrusion plus rolling and direct rolling. The material processed using the former method exhibits arelatively high superplasticity with a maximum superplastic elongation of 465 % , whereas thatprocessed using the latter method exhibits a maximum superplastic elongation of 295 % . Materialsprocessed using extrusion plus rolling and direct rolling both exhibit similar stress-strainbehavior and strain rate sensitivity factors. The strain rate factors are in the 0.3 to 0.5 range.The difference in their superplastic elongation is possibly the result of differences in grain sizeand available cavity nucleation sites provided by closed gas pores.
文摘The microstructure with uniform equiaxed fine gain was obtained by the thermo-mechanical processing （TMP） for the 5083 Al alloy （Al-4.56%Mg-0.61%Mn） plate. Uniaxial tensile test was carried out at a temperature range of 500-570 ℃ and a strain rate range of 4.17×10^-4 s-1^- 1×10^- 2 s^- 1. Maximum tensile elongation 530% was obtained at 550 ℃ and strain rate ε＆ =4 .17×10^-4 s^-1. Dislocations were observed in grain interiors and at grain boundaries during uniaxial tensile deformation by transmission electronic microscopy （TEM）, respectively. Results show that the grain boundary sliding （GBS） accommodated by dislocation motion is the principal reason for superplastic deformation. The cavities and fracture were observed during uniaxial tensile deformation of the alloy by scanning electronic microscopy （SEM）, indicating that linkage of cavities in large region would induce failure of the material. Moreover, presence of liquid phase at grain boundary also affects the superplastic deformation and behavior of cavities.
文摘Laser-MIG hybrid welding process was dealt with 6 mm thick 5083Hl16 Al-Mg alloy plate in butt-joint configuration. Weld formation principle during hybrid welding was explained. The joint properties and microstructure characteristics of welded joints were analyzed by tensile tests, fractographs observed by optical microscopy and scanning electron microscopy （SEM）. Higher heat input could obtain better mechanical properties, and tensile strength and elongation reached 97.2%, 81% of the base metal, respectively. Fracture position traasited from fusion line to weld center in the higher heat input, and fracture location were only in the center of welded joints for the heat input relatively small.
基金Supported by Department of Education of Liaoning Province(Grant No.JDL2020019)Dalian High Level Talents Project(Grant No.2017RQ132).
文摘With the popularization of friction stir welding(FSW),5083-H321 and 6061-T6 aluminum alloy materials are widely used during the FSW process.In this study,the fatigue life of friction stir welding with two materials,i.e.,5083-H321 and 6061-T6 aluminum alloy,are studied.Fatigue tests were carried out on the base metal of these two materials as well as on the butt joints and overlapping FSW samples.The principle of the equivalent structural stress method is used to analyze the FSW test data of these two materials.The fatigue resistances of these two materials were com-pared and a unified principal S-N curve equation was fitted.Two key parameters of the unified principal S-N curve obtained by fitting,Cd is 4222.5,and h is 0.2693.A new method for an FSW fatigue life assessment was developed in this study and can be used to calculate the fatigue life of different welding forms with a single S-N curve.Two main fatigue tests of bending and tension were used to verify the unified principal S-N curve equation.The results show that the fatigue life calculated by the unified mean 50%master S-N curve parameters are the closest to the fatigue test results.The reliability,practicability,and generality of the master S-N curve fitting parameters were verified using the test data.The unified principal S-N curve acquired in this study can not only be used in aluminum alloy materials but can also be applied to other materials.
基金Sponsored by the National Science and Technology Mayor Project(Grant No.2010ZX04014-073-01)
文摘Abstract： The superplastic response of commercial 5083 alloy （Al-4. 42Mg） under uniaxial tension at strain rates ranging from 5 × 10-5 to 10-2s -1 in the temperature interval 400 -550℃ was systematically studied in this paper. The tension test was conducted on samples of rolling direction. The maximum elongation-to-failure of 486% was found at 500 % and strain rate of 10-4s-1. To identify the main characteristics of superplastic deformation and to determine the mechanism of superplastic deformation of the alloy, the microstructure and fracture of the alloy were analyzed as a function of strain, strain rate and temperature using optical microscopy （OM） and scanning electron microscopy （SEM）, the apparent strain rate sensitivity exponent ma and the apparent activation energy Qa were also studied. Based on the fracture analysis and the calculated data of m and Qa, it is suggested that the dominant deformation mechanism in the present alloy is grain boundary sliding （GBS） during the best deformation condition.
文摘Thepurpose of the present paper is to study the mechanical propertiesand microstructureof the twin-roll cast and cold rolled AA5083 aluminum alloy sheet in strain-hardened H321 temper. To reach this goal, first, a sound surface slab of 8.90 mm thick and 1260 mm wide was cast by a 15°; tilt back twin roll caster at a casting speed of 490 mm/min. After homogenization at 520 ℃, the product was cold rolled to two thicknesses of 6.30 mm and 3.85 mm with an intermediate annealing at 370 ℃ and final stabilization at 180 ℃. Opticalmicroscopyand scanning electron microscopy （SEM） investigations of the as-cast state depicted the segregation of intermetallic particles mainly in grain boundaries which wasthe cause of grain removal observed in the fracture surface of tensile test samples. In addition, mechanical properties indicated an increase in total elongation after homogenization heat treatment dueto the elimination of the grain boundary segregations. Finally, it was observed that the properties of the 3.85 mmthick sheet were consistent with the H321 temper requirements according to ASTM B 290M standard due to applying sufficient cold reduction during cold rolling stage.
文摘With no annealing treatment, cathodic polarization trends in 5083F A1 alloy revealed concentration polarization and activation polarization. However, the annealed specimens have lower current densities at corrosion protection potential compared to the non-annealed specimen. The results of SSRTs conducted in seawater at the applied potential range of-l.8 V to -0.5 V indicated that the maximum tensile strength, elongation, and time-to-fracture had high values at applied potentials of -0.7 to -1.4 V. The maximum tensile strength, elongation, and time-to-f？acture decreased when the potential values were beyond this range in either anodic or cathodic direction. In general, the increased shear lip caused by annealing treatment indicates elongation. Time-to-fracture would likely increase with elongation. Potentials between -0.5 V to -0.6 V were found to be in the region of stress corrosion cracking. The corrosion protection zone was determined to be -0.7 V to -J,4 V because these potential ranges produced good mechanical properties. Potential less than -1.4 V produced a fractured surface with a mixture of dimples （ductile fractures） and a quasi-cleavage pattern resulting from the effects of hydrogen gas.
基金financially supported by the Nature Science Research Project of Anhui Province(No.1808085QE136)the Anhui Postdoctoral Science Foundation(No.934269)the National Natural Science Foundation of China(No.51905143)。
文摘To enhance the stress corrosion cracking(SCC)resistance,Zn was utilized as an alloy element to add in the AA5083 aluminum alloys.The effects of Zn content on the microstructures,mechanical properties and SCC resistance were systematically evaluated.The results demonstrate that in the studied range adding Zn can significantly improve the SCC resistance of the AA5083 alloys.This is related to the relatively low amount of continuous β(Al3Mg2)phase along grain boundary and the formation of Zn-containing phase such as Al5Mg11Zn4 phase.Based on the results,the optimal Zn content with respect to SCC resistance is approximately 0.50 wt.%.Further increasing Zn content results in coarse precipitates discontinuously distributed along grain boundaries.
文摘Aluminum alloy 5083(AA5083)processed by large-scale Equal-channel angular pressing(ECAP)is an excellent engineering material with great prospects for industrial applications.An accurate assessment of the underlying constitutive relationships with easily determined material constants is critical for the predictive design and informed processing of such structural materials.To develop such a design framework,uniaxial dynamic compressive tests over a wide range of temperatures(293-573 K)were carried out for an ECAP-processed AA5083 alloy.Additionally,the microstructure before and after dynamic loading was characterized by SEM and TEM.Based on the experimental results,a new dynamic constitutive model,based on thermal activation theory,was established to describe the plastic flow behavior of the AA5083 alloy that incorporates the effects of plastic strain,temperature,and strain rate.The input parameters of the new model were determined using a particle swarm optimization(PSO)method.The model predictions show excellent agreement with experimental results,which suggests that the current predictive constitutive model is highly effective in reproducing the dynamic deformation behavior of the large-scale ECAP-processed AA5083.
