Low-temperature ausforming(LT-AF)prior to bainitic transformation leads to a noticeable acceleration of bainitic transformation kinetics;however,the effect of LT-AF on the retained austenite(RA)features and the result...Low-temperature ausforming(LT-AF)prior to bainitic transformation leads to a noticeable acceleration of bainitic transformation kinetics;however,the effect of LT-AF on the retained austenite(RA)features and the resulting mechanical properties is still unclear.LT-AF was applied to ultrahigh-strength bainitic steel before austempering.The deformation behavior and the resulting dislocation substructures were investigated by thermomechanical simulator and transmission electron microscopy(TEM).The planar dislocation structures produced during deformation at 350℃ accelerate the bainitic transformation kinetics during isothermal holding.The effect of LT-AF on the bainitic transformation kinetics and the features of RA was elucidated via dilatometer measurement,TEM,scanning electron microscopy,and X-ray diffraction.It is observed that LT-AF not only retains more RA content but also facilitates improved RA stability.This trend is mainly due to the large amounts of planar dislocations in RA and bainitic laths inherited from undercooled austenite caused by LT-AF,the decrease in bainitic sheaves size,and the increase in filmy RA content compared to the sample without ausforming.A large fraction of filmy RA with high stability and the refinement of bainitic sheaves obtained by LT-AF remarkably enhance the strain hardening capacity and achieve significantly better ductility compared to the directly austempered sample.展开更多
The effects of ausforming procedure and subsequent annealing treatments on microstructures of cobalt（Co）samples are investigated by electron channeling contrast and electron backscatter diffraction techniques.Result...The effects of ausforming procedure and subsequent annealing treatments on microstructures of cobalt（Co）samples are investigated by electron channeling contrast and electron backscatter diffraction techniques.Results show that the ausformed Co samples consist of coarsen blocky laths（single ε phase）with the irregular morphology and the ultra-fine acicular laths（dual phase：γ and ε）with the slender and rectangular morphologies.As compared to the slight reduction sample,the much denser acicular laths are observed in the heavily ausformed sample.In addition,recrystallization behavior and annealing-induced 7--＋ e transformation have occurred in ausformed Co samples during the annealing treatment.展开更多
The addition of boron（B） is frequently adopted to increase the hardenability of bainitic steels. Although it is well known that B can retard the bainitic transformation kinetics, it is still not clear how the B affe...The addition of boron（B） is frequently adopted to increase the hardenability of bainitic steels. Although it is well known that B can retard the bainitic transformation kinetics, it is still not clear how the B affects the bainitic transformation kinetics after ausforming. By systematic high-resolution dilatometry tests, the present work reveals that the bainitic transformation kinetics is accelerated in a low C steel with B addition after ausforming from all aspects including incubation time, transformation velocity and transformed volume fraction. In contrast, for the same steel without B addition, both transformation velocity and transformed volume fraction are retarded after ausforming. It is proposed that ausforming can reduce B segregation at prior austenite grain boundaries as some boron can interact with dislocations and therefore enhance bainite nucleation rate. Furthermore, auforming can refine the average volume of bainitic sheaf. Based on the competing mechanisms between increase of nucleation rate and refinement of bainitic sheaf, the effects of B and ausforming on the bainitic transformation kinetics are discussed.展开更多
The production of lightweight ferrous castings with increased strength properties became unavoidable facing the serious challenge of lighter aluminum and magnesium castings. The relatively new ferrous casting alloy AD...The production of lightweight ferrous castings with increased strength properties became unavoidable facing the serious challenge of lighter aluminum and magnesium castings. The relatively new ferrous casting alloy ADI offers promising strength prospects, and the thermo-mechanical treatment of ductile iron may suggest a new route for production of thin-wall products. This work aims at studying the influence of thermomechanical treatment, either by ausforming just after quenching and before the onset of austempering reaction or by cold rolling after austempering. In the first part of this work, ausforming of ADI up to 25% reduction in height during a rolling operation was found to add a mechanical processing component compared to the conventional ADI heat treatment, thus increasing the rate of ausferrite formation and leading to a much finer and more homogeneous ausferrite product. The kinetics of ausferrite formation was studied using both metallographic as well as XRD-techniques. The effect of ausforming on the strength was quite dramatic （up to 70% and 50% increase in the yield and ultimate strength respectively）. A mechanism involving both a refined microstructural scale and an elevated dislocation density was suggested. Nickel is added to ADI to increase hardenability of thick section castings, while ausforming to higher degrees of deformation is necessary to alleviate the deleterious effect of alloy segregation on ductility. In the second part of this work, the influence of cold rolling （CR） on the mechanical properties and structural characteristics of ADI was investigated. The variation in properties was related to the amount of retained austenite （7~） and its mechanically induced transformation. In the course of tensile deformation of ADI, transformation induced plasticity （TRIP） takes place, indicated by the increase of the instantaneous value of strain-hardening exponent with tensile strain. The amount of retained austenite was found to decrease due to partial transformation of 7~ to martensite under the CR strain. Such strain-induced transformation resulted in higher amounts of mechanically generated martensite. The strength and hardness properties were therefore increased, while ductility and impact toughness decreased with increasing CR reduction.展开更多
The effect of austenite deformation on the pearlite microstructure of eutectoid steel w as investigated by hot uniaxial compression tests using a Gleeble 1500 thermo-mechanical simulator. The results show ed that the ...The effect of austenite deformation on the pearlite microstructure of eutectoid steel w as investigated by hot uniaxial compression tests using a Gleeble 1500 thermo-mechanical simulator. The results show ed that the deformation of the austenite phase accelerated the transformation of pearlite,leading to a smaller colony size and a smaller interlamellar space of pearlite; meanw hile,the orientation of pearlite lamellae became more heterogeneous,and the lamellar thickness decreased. Larger strain of austenite w as observed to accelerate the spheroidization process of carbides w ithin pearlite colonies.展开更多
基金The financial support provided by the National Natural Science Foundation of China(No.U1808208)the Fundamental Research Funds for the Central Universities(N2107005)is gratefully acknowledged.
文摘Low-temperature ausforming(LT-AF)prior to bainitic transformation leads to a noticeable acceleration of bainitic transformation kinetics;however,the effect of LT-AF on the retained austenite(RA)features and the resulting mechanical properties is still unclear.LT-AF was applied to ultrahigh-strength bainitic steel before austempering.The deformation behavior and the resulting dislocation substructures were investigated by thermomechanical simulator and transmission electron microscopy(TEM).The planar dislocation structures produced during deformation at 350℃ accelerate the bainitic transformation kinetics during isothermal holding.The effect of LT-AF on the bainitic transformation kinetics and the features of RA was elucidated via dilatometer measurement,TEM,scanning electron microscopy,and X-ray diffraction.It is observed that LT-AF not only retains more RA content but also facilitates improved RA stability.This trend is mainly due to the large amounts of planar dislocations in RA and bainitic laths inherited from undercooled austenite caused by LT-AF,the decrease in bainitic sheaves size,and the increase in filmy RA content compared to the sample without ausforming.A large fraction of filmy RA with high stability and the refinement of bainitic sheaves obtained by LT-AF remarkably enhance the strain hardening capacity and achieve significantly better ductility compared to the directly austempered sample.
基金supported by the National Natural Science Foundation of China(Nos.51501026 and 51401039)the Natural Science Foundation of Chongqing(CSTC2014jcyj A50017)+1 种基金the Scientific and Technological Research Program of Chongqing Municipal Education Commission(No.KJ1500923)the Australian Research Council
文摘The effects of ausforming procedure and subsequent annealing treatments on microstructures of cobalt（Co）samples are investigated by electron channeling contrast and electron backscatter diffraction techniques.Results show that the ausformed Co samples consist of coarsen blocky laths（single ε phase）with the irregular morphology and the ultra-fine acicular laths（dual phase：γ and ε）with the slender and rectangular morphologies.As compared to the slight reduction sample,the much denser acicular laths are observed in the heavily ausformed sample.In addition,recrystallization behavior and annealing-induced 7--＋ e transformation have occurred in ausformed Co samples during the annealing treatment.
基金the financial support by the Steel Joint Funds of the National Natural Science Foundation of China(Grant No.U1560204)National Natural Science Foundation of China(Grant No.51301148)+2 种基金the Research Grants Council of Hong Kong(Grant Nos.HKU719712E,HKU712713E,17203014)Shenzhen Science,the Technology and Innovation Commission(Grant No.JCYJ20150629151046886)financial support from National Natural Science Foundation of China(Grant No.51574080)
文摘The addition of boron（B） is frequently adopted to increase the hardenability of bainitic steels. Although it is well known that B can retard the bainitic transformation kinetics, it is still not clear how the B affects the bainitic transformation kinetics after ausforming. By systematic high-resolution dilatometry tests, the present work reveals that the bainitic transformation kinetics is accelerated in a low C steel with B addition after ausforming from all aspects including incubation time, transformation velocity and transformed volume fraction. In contrast, for the same steel without B addition, both transformation velocity and transformed volume fraction are retarded after ausforming. It is proposed that ausforming can reduce B segregation at prior austenite grain boundaries as some boron can interact with dislocations and therefore enhance bainite nucleation rate. Furthermore, auforming can refine the average volume of bainitic sheaf. Based on the competing mechanisms between increase of nucleation rate and refinement of bainitic sheaf, the effects of B and ausforming on the bainitic transformation kinetics are discussed.
文摘The production of lightweight ferrous castings with increased strength properties became unavoidable facing the serious challenge of lighter aluminum and magnesium castings. The relatively new ferrous casting alloy ADI offers promising strength prospects, and the thermo-mechanical treatment of ductile iron may suggest a new route for production of thin-wall products. This work aims at studying the influence of thermomechanical treatment, either by ausforming just after quenching and before the onset of austempering reaction or by cold rolling after austempering. In the first part of this work, ausforming of ADI up to 25% reduction in height during a rolling operation was found to add a mechanical processing component compared to the conventional ADI heat treatment, thus increasing the rate of ausferrite formation and leading to a much finer and more homogeneous ausferrite product. The kinetics of ausferrite formation was studied using both metallographic as well as XRD-techniques. The effect of ausforming on the strength was quite dramatic （up to 70% and 50% increase in the yield and ultimate strength respectively）. A mechanism involving both a refined microstructural scale and an elevated dislocation density was suggested. Nickel is added to ADI to increase hardenability of thick section castings, while ausforming to higher degrees of deformation is necessary to alleviate the deleterious effect of alloy segregation on ductility. In the second part of this work, the influence of cold rolling （CR） on the mechanical properties and structural characteristics of ADI was investigated. The variation in properties was related to the amount of retained austenite （7~） and its mechanically induced transformation. In the course of tensile deformation of ADI, transformation induced plasticity （TRIP） takes place, indicated by the increase of the instantaneous value of strain-hardening exponent with tensile strain. The amount of retained austenite was found to decrease due to partial transformation of 7~ to martensite under the CR strain. Such strain-induced transformation resulted in higher amounts of mechanically generated martensite. The strength and hardness properties were therefore increased, while ductility and impact toughness decreased with increasing CR reduction.
文摘The effect of austenite deformation on the pearlite microstructure of eutectoid steel w as investigated by hot uniaxial compression tests using a Gleeble 1500 thermo-mechanical simulator. The results show ed that the deformation of the austenite phase accelerated the transformation of pearlite,leading to a smaller colony size and a smaller interlamellar space of pearlite; meanw hile,the orientation of pearlite lamellae became more heterogeneous,and the lamellar thickness decreased. Larger strain of austenite w as observed to accelerate the spheroidization process of carbides w ithin pearlite colonies.
