A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A ...A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.展开更多
Cantilever casting concrete arch bridge using form traveller has a broad application prospect.However,it is difficult to obtain reasonable initial cable force in construction stage.In this study,stress balance and inf...Cantilever casting concrete arch bridge using form traveller has a broad application prospect.However,it is difficult to obtain reasonable initial cable force in construction stage.In this study,stress balance and influence matrix methods were developed to determine the initial cable force of cantilever casting concrete arch bridge.The stress balance equation and influence matrix of arch rib critical section were established,and the buckle cable force range was determined by the allowable stress of arch rib critical section.Then a group of buckle cable forces were selected and substituted into the stress balance equation,and the reasonable initial buckle cable force was determined through iteration.Based on the principle of force balance,the initial anchor cable force was determined.In an engineering application example,it is shown that the stress balance and influence matrix methods for the determination of initial cable force are feasible and reliable.The initial cable forces of arch rib segments only need to be adjusted once in the corresponding construction process,which improves the working efficiency and reduces the construction risk.It is found that the methods have great advantages for determining initial cable force in cantilever casting construction process of concrete arch bridge.展开更多
Positive results are proved here about the ability of balanced methods to reproduce the mean square stability of the impulsive stochastic differential equations. It is shown that the balanced methods with strong conve...Positive results are proved here about the ability of balanced methods to reproduce the mean square stability of the impulsive stochastic differential equations. It is shown that the balanced methods with strong convergence can preserve the mean square stability with the sufficiently small stepsize. Weak variants and their mean square stability are also considered. Several numerical experiments are given for illustration and show that the fully implicit methods are superior to those of the explicit methods in terms of mean-square stabilities for relatively large stepsizes especially.展开更多
A class of general modified split-step balanced methods proposed in the paper can be applied to solve stiff stochastic differential systems with m-dimensional multiplicative noise. Compared to some other already repor...A class of general modified split-step balanced methods proposed in the paper can be applied to solve stiff stochastic differential systems with m-dimensional multiplicative noise. Compared to some other already reported split-step balanced methods, the drift increment function of the methods can be taken from any chosen ane-step ordinary differential equations （ODEs） solver. The schemes is proved to be strong convergent with order one. For the mean-square stability analysis, the investigation is confined to two cases. Some numerical experiments are reported to testify the performance and the effectiveness of the methods.展开更多
The harmonic balance method(HBM)is one of the most widely used methods in solving nonlinear vibration problems,and its accuracy and computational efficiency largely depend on the number of the harmonics selected.The a...The harmonic balance method(HBM)is one of the most widely used methods in solving nonlinear vibration problems,and its accuracy and computational efficiency largely depend on the number of the harmonics selected.The adaptive harmonic balance(AHB)method is an improved HBM method.This paper presents a modified AHB method with the asymptotic harmonic selection(AHS)procedure.This new harmonic selection procedure selects harmonics from the frequency spectra of nonlinear terms instead of estimating the contribution of each harmonic to the whole nonlinear response,by which the additional calculation is avoided.A modified continuation method is proposed to deal with the variable size of nonlinear algebraic equations at different values of path parameters,and then all solution branches of the amplitude-frequency response are obtained.Numerical experiments are carried out to verify the performance of the AHB-AHS method.Five typical nonlinear dynamic equations with different types of nonlinearities and excitations are chosen as the illustrative examples.Compared with the classical HBM and Runge-Kutta methods,the proposed AHB-AHS method is of higher accuracy and better convergence.The AHB-AHS method proposed in this paper has the potential to investigate the nonlinear vibrations of complex high-dimensional nonlinear systems.展开更多
Eliminating the effects of gravity and designing nonlinear energy sinks(NESs)that suppress vibration in the vertical direction is a challenging task with numerous damping requirements.In this paper,the dynamic design ...Eliminating the effects of gravity and designing nonlinear energy sinks(NESs)that suppress vibration in the vertical direction is a challenging task with numerous damping requirements.In this paper,the dynamic design of a vertical track nonlinear energy sink(VTNES)with zero linear stiffness in the vertical direction is proposed and realized for the first time.The motion differential equations of the VTNES coupled with a linear oscillator(LO)are established.With the strong nonlinearity considered of the VTNES,the steady-state response of the system is analyzed with the harmonic balance method(HBM),and the accuracy of the HBM is verified numerically.On this basis,the VTNES prototype is manufactured,and its nonlinear stiffness is identified.The damping effect and dynamic characteristics of the VTNES are studied theoretically and experimentally.The results show that the VTNES has better damping effects when strong modulation responses(SMRs)occur.Moreover,even for small-amplitude vibration,the VTNES also has a good vibration suppression effect.To sum up,in order to suppress the vertical vibration,an NES is designed and developed,which can suppress the vertical vibration within certain ranges of the resonance frequency and the vibration intensity.展开更多
The time domain harmonic balance method is an attractive reduced order method of analyzing unsteady flow for turbomachines. However, the method can admit non-physical solutions. Non-physical solutions were encountered...The time domain harmonic balance method is an attractive reduced order method of analyzing unsteady flow for turbomachines. However, the method can admit non-physical solutions. Non-physical solutions were encountered from a three-blade-row compressor configuration in a time domain harmonic balance analysis. This paper aims to investigate the root cause of the non-physical solutions. The investigation involves several strategies, which include increasing the number of harmonics, increasing the number of time instants, including scattered modes,including the rotor-rotor interaction, and the use of a new method-the approximate time domain nonlinear harmonic method. Numerical analyses pertinent to each strategy are presented to reveal the root cause of the non-physical solution. It is found that the nonlinear interaction of unsteady flow components with different fundamental frequencies is the cause of the non-physical solution. The non-physical solution can be eliminated by incorporating extra scattered modes or using the approximate time domain nonlinear harmonic method.展开更多
Comparisons of the common methods for obtaining the periodic responses show that the harmonic balance method with alternating frequency/time （HB-AFT） do- main technique has some advantages in dealing with nonlinear ...Comparisons of the common methods for obtaining the periodic responses show that the harmonic balance method with alternating frequency/time （HB-AFT） do- main technique has some advantages in dealing with nonlinear problems of fractional exponential models. By the HB-AFT method, a rigid rotor supported by ball bearings with nonlinearity of Hertz contact and ball passage vibrations is considered. With the aid of the Floquet theory, the movement characteristics of interval stability are deeply studied. Besides, a simple strategy to determine the monodromy matrix is proposed for the stability analysis.展开更多
We have deduced incremental harmonic balance an iteration scheme in the （IHB） method using the harmonic balance plus the Newton-Raphson method. Since the convergence of the iteration is dependent upon the initial va...We have deduced incremental harmonic balance an iteration scheme in the （IHB） method using the harmonic balance plus the Newton-Raphson method. Since the convergence of the iteration is dependent upon the initial values in the iteration, the convergent region is greatly restricted for some cases. In this contribution, in order to enlarge the convergent region of the IHB method, we constructed the zeroth-order deformation equation using the homotopy analysis method, in which the IHB method is employed to solve the deformation equation with an embedding parameter as the active increment. Taking the Duffing and the van der Pol equations as examples, we obtained the highly accurate solutions. Importantly, the presented approach renders a convenient way to control and adjust the convergence.展开更多
We applied the material balance principle of the denudation volume and sedimentary flux to study the denudation-accumulation system between the Longmen Mountains （Mts.） and the foreland basin. The amount of sediment...We applied the material balance principle of the denudation volume and sedimentary flux to study the denudation-accumulation system between the Longmen Mountains （Mts.） and the foreland basin. The amount of sediment in each sedimentation stage of the basin was estimated to obtain the denudation volume, erosion thickness and deposit thickness since the Late Triassic Epoch, to enable us to recover the paleoelevation of the provenance and the sedimentary area. The results show the following： （1） Since the Late Triassic Epoch, the elevation of the surface of the Longmen Mts. has uplifted from 0 m to 2751 m, and the crust of the Longmen Mts. has uplifted by 9.8 km. Approximately 72% of the materials introduced have been denuded from the mountains. （2） It is difficult to recover the paleoelevation of each stage of the Longmen Mts. foreland basin quantitatively by the present-day techniques and data. （3） The formation of the Longmen Mts. foreland basin consisted of three stages of thrust belt tectonic load and three stages of thrust belt erosional unload. During tectonic loading stages （Late Triassic Epoch, Late Jurassic-Early Cretaceous, Late Cretaceous-Miocene）, the average elevation of Longmen Mts. was lower （approximately 700-1700 m）. During erosional unloading stages （Early and Middle Jurassic, Middle Cretaceous and Jiaguan, Late Cenozoic）, the average elevation of Longmen Mts. was high at approximately 2000-2800m.展开更多
A modified homogeneous balance method is proposed by improving some key steps in the homogeneousbalance method.Bilinear equations of some nonlinear evolution equations are derived by using the modified homogeneousbala...A modified homogeneous balance method is proposed by improving some key steps in the homogeneousbalance method.Bilinear equations of some nonlinear evolution equations are derived by using the modified homogeneousbalance method.Generalized Boussinesq equation,KP equation,and mKdV equation are chosen as examples to illustrateour method.This approach is also applicable to a large variety of nonlinear evolution equations.展开更多
The incremental harmonic balance method was extended to analyze the flutter of systems with multiple structural strong nonlinearities. The strongly nonlinear cubic plunging and pitching stiffness terms were considered...The incremental harmonic balance method was extended to analyze the flutter of systems with multiple structural strong nonlinearities. The strongly nonlinear cubic plunging and pitching stiffness terms were considered in the flutter equations of two-dimensional airfoil. First, the equations were transferred into matrix form, then the vibration process was divided into the persistent incremental processes of vibration moments. And the expression of their solutions could be obtained by using a certain amplitude as control parameter in the harmonic balance process, and then the bifurcation, limit cycle flutter phenomena and the number of harmonic terms were analyzed. Finally, numerical results calculated by the Runge-Kutta method were given to verify the results obtained by the proposed procedure. It has been shown that the incremental harmonic method is effective and precise in the analysis of strongly nonlinear flutter with multiple structural nonlinearities.展开更多
The dynamical properties of fractional-order Duffing–van der Pol oscillator are studied, and the amplitude–frequency response equation of primary resonance is obtained by the harmonic balance method. The stability c...The dynamical properties of fractional-order Duffing–van der Pol oscillator are studied, and the amplitude–frequency response equation of primary resonance is obtained by the harmonic balance method. The stability condition for steady-state solution is obtained based on Lyapunov theory. The comparison of the approximate analytical results with the numerical results is fulfilled, and the approximations obtained are in good agreement with the numerical solutions. The bifurcations of primary resonance for system parameters are analyzed. The results show that the harmonic balance method is effective and convenient for solving this problem, and it provides a reference for the dynamical analysis of similar nonlinear systems.展开更多
Based on the homogenous balance method and with the help of mathematica, the Backlund transformation and the transfer heat equation are derived. Analyzing the heat-transfer equation, the multiple soliton solutions and...Based on the homogenous balance method and with the help of mathematica, the Backlund transformation and the transfer heat equation are derived. Analyzing the heat-transfer equation, the multiple soliton solutions and other exact analytical solution for Whitham-Broer-Kaup equations(WBK) are derived. These solutions contain Fan's, Xie's and Yan's results and other new types of analytical solutions, such as rational function solutions and periodic solutions. The method can also be applied to solve more nonlinear differential equations.展开更多
In this paper, we present a solution methodology to obtain exact solutions of some nonlinear evolution equation by modifying the homogeneous balance method. Based on the modified homogeneous balance method, several ki...In this paper, we present a solution methodology to obtain exact solutions of some nonlinear evolution equation by modifying the homogeneous balance method. Based on the modified homogeneous balance method, several kinds of exact（new） solutions of the generalized KdV equation are obtained.展开更多
In this paper, the Auto-B?cklund transformation connected with the homogeneous balance method (HB) and the extended tanh-function method are used to construct new exact solutions for the time-dependent coefficients Ca...In this paper, the Auto-B?cklund transformation connected with the homogeneous balance method (HB) and the extended tanh-function method are used to construct new exact solutions for the time-dependent coefficients Calogero-Degasperis (VCCD) equation. New soliton and periodic solutions of many types are obtained. Furthermore, the soliton propagation is discussed under the effect of the variable coefficients.展开更多
The coupling vibration of a hydraulic pipe system consisting of two pipes is studied.The pipes are installed in parallel and fixed at their ends,and are restrained by clips to one bracket at their middle points.The pi...The coupling vibration of a hydraulic pipe system consisting of two pipes is studied.The pipes are installed in parallel and fixed at their ends,and are restrained by clips to one bracket at their middle points.The pipe subjected to the basement excitation at the left end is named as the active pipe,while the pipe without excitation is called the passive pipe.The clips between the two pipes are the bridge for the vibration energy.The adjacent natural frequencies will enhance the vibration coupling.The governing equation of the coupled system is deduced by the generalized Hamilton principle,and is discretized to the modal space.The modal correction is used during the discretization.The investigation on the natural characters indicates that the adjacent natural frequencies can be adjusted by the stiffness of the two clips and bracket.The harmonic balance method(HBM)is used to study the responses in the adjacent natural frequency region.The results show that the vibration energy transmits from the active pipe to the passive pipe swimmingly via the clips together with a flexible bracket,while the locations of them are not node points.The adjacent natural frequencies may arouse wide resonance curves with two peaks for both pipes.The stiffness of the clip and bracket can release the vibration coupling.It is suggested that the stiffness of the clip on the passive pipe should be weak and the bracket should be strong enough.In this way,the vibration energy is reflected by the almost rigid bracket,and is hard to transfer to the passive pipe via a soft clip.The best choice is to set the clips at the pipe node points.The current work gives some suggestions for weakening the coupled vibration during the dynamic design of a coupled hydraulic pipe system.展开更多
In this study,a coupling model of fluid-conveying pipes made of functionally graded materials(FGMs)with NiTiNOL-steel(NiTi-ST)for vibration absorption is investigated.The vibration responses of the FGM fluid-conveying...In this study,a coupling model of fluid-conveying pipes made of functionally graded materials(FGMs)with NiTiNOL-steel(NiTi-ST)for vibration absorption is investigated.The vibration responses of the FGM fluid-conveying pipe with NiTi-ST are studied by the Galerkin truncation method(GTM)and harmonic balance method(HBM).The harmonic balance solutions and the numerical results are consistent.Also,the linearized stability of the structure is determined.The effects of the structure parameters on the absorption performance are also studied.The results show that the NiTi-ST is an effective means of vibration absorption.Furthermore,in studying the effect of the NiTi-ST,a closed detached response(CDR)is first observed.It is noteworthy that the CDR may dramatically change the vibration amplitude and that the parameters of the NiTi-ST may determine the emergence or disappearance of the CDR.This vibration absorption device can be extended to offer more general vibration control in engineering applications.展开更多
Wireless Sensor Network(WSN)technology is the real-time applica-tion that is growing rapidly as the result of smart environments.Battery power is one of the most significant resources in WSN.For enhancing a power facto...Wireless Sensor Network(WSN)technology is the real-time applica-tion that is growing rapidly as the result of smart environments.Battery power is one of the most significant resources in WSN.For enhancing a power factor,the clustering techniques are used.During the forward of data in WSN,more power is consumed.In the existing system,it works with Load Balanced Cluster-ing Method(LBCM)and provides the lifespan of the network with scalability and reliability.In the existing system,it does not deal with end-to-end delay and deliv-ery of packets.For overcoming these issues in WSN,the proposed Genetic Algo-rithm based on Chicken Swarm Optimization(GA-CSO)with Load Balanced Clustering Method(LBCM)is used.Genetic Algorithm generates chromosomes in an arbitrary method then the chromosomes values are calculated using Fitness Function.Chicken Swarm Optimization(CSO)helps to solve the complex opti-mization problems.Also,it consists of chickens,hens,and rooster.It divides the chicken into clusters.Load Balanced Clustering Method(LBCM)maintains the energy during communication among the sensor nodes and also it balances the load in the gateways.The proposed GA-CSO with LBCM improves the life-span of the network.Moreover,it minimizes the energy consumption and also bal-ances the load over the network.The proposed method outperforms by using the following metrics such as energy efficiency,ratio of packet delivery,throughput of the network,lifetime of the sensor nodes.Therefore,the evaluation result shows the energy efficiency that has achieved 83.56%and the delivery ratio of the packet has reached 99.12%.Also,it has attained linear standard deviation and reduced the end-to-end delay as 97.32 ms.展开更多
基金support from the Youth Innovation Promotion Association of Chinese Academy of Sciences (Grant No.2019319)support from the Start-up Foundation of Suzhou Institute of Nano-Tech and Nano-Bionics,CAS,Suzhou (Grant No.Y9AAD110)。
文摘A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.
基金Projects(51478049,51778068)supported by the National Natural Science Foundation of ChinaProject(14JJ2075,2019JJ40301)supported by the Hunan Natural Science Foundation of China+1 种基金Project(17A010)supported by the Scientific Research Fund of Hunan Provincial Education Department of ChinaProject(2017GK4034)supported by the Major Technological Achievements Transformation Program of Hunan Strategic Emerging Industries of China
文摘Cantilever casting concrete arch bridge using form traveller has a broad application prospect.However,it is difficult to obtain reasonable initial cable force in construction stage.In this study,stress balance and influence matrix methods were developed to determine the initial cable force of cantilever casting concrete arch bridge.The stress balance equation and influence matrix of arch rib critical section were established,and the buckle cable force range was determined by the allowable stress of arch rib critical section.Then a group of buckle cable forces were selected and substituted into the stress balance equation,and the reasonable initial buckle cable force was determined through iteration.Based on the principle of force balance,the initial anchor cable force was determined.In an engineering application example,it is shown that the stress balance and influence matrix methods for the determination of initial cable force are feasible and reliable.The initial cable forces of arch rib segments only need to be adjusted once in the corresponding construction process,which improves the working efficiency and reduces the construction risk.It is found that the methods have great advantages for determining initial cable force in cantilever casting construction process of concrete arch bridge.
基金National Natural Science Foundations of China(Nos.11561028,11101101,11461032,11401267)Natural Science Foundations of Jiangxi Province,China(Nos.20151BAB201013,20151BAB201010,20151BAB201015)
文摘Positive results are proved here about the ability of balanced methods to reproduce the mean square stability of the impulsive stochastic differential equations. It is shown that the balanced methods with strong convergence can preserve the mean square stability with the sufficiently small stepsize. Weak variants and their mean square stability are also considered. Several numerical experiments are given for illustration and show that the fully implicit methods are superior to those of the explicit methods in terms of mean-square stabilities for relatively large stepsizes especially.
基金National Natural Science Foundation of China(No.11171352)
文摘A class of general modified split-step balanced methods proposed in the paper can be applied to solve stiff stochastic differential systems with m-dimensional multiplicative noise. Compared to some other already reported split-step balanced methods, the drift increment function of the methods can be taken from any chosen ane-step ordinary differential equations （ODEs） solver. The schemes is proved to be strong convergent with order one. For the mean-square stability analysis, the investigation is confined to two cases. Some numerical experiments are reported to testify the performance and the effectiveness of the methods.
基金Project supported by the National Natural Science Foundation of China(Nos.11972129 and12372008)the National Major Science and Technology Projects of China(No.2017-IV-0008-0045)+3 种基金the Natural Science Foundation of Heilongjiang Province of China(No.YQ2022A008)the Fundamental Research Funds for the Central Universities of China(No.HIT.OCEF.2023006)the Polish National Science Centre of Poland under the OPUS 18 grant(No.2019/35/B/ST8/00980)the Tianjin University Independent Innovation Foundation of China(No.2023XJS-0038)。
文摘The harmonic balance method(HBM)is one of the most widely used methods in solving nonlinear vibration problems,and its accuracy and computational efficiency largely depend on the number of the harmonics selected.The adaptive harmonic balance(AHB)method is an improved HBM method.This paper presents a modified AHB method with the asymptotic harmonic selection(AHS)procedure.This new harmonic selection procedure selects harmonics from the frequency spectra of nonlinear terms instead of estimating the contribution of each harmonic to the whole nonlinear response,by which the additional calculation is avoided.A modified continuation method is proposed to deal with the variable size of nonlinear algebraic equations at different values of path parameters,and then all solution branches of the amplitude-frequency response are obtained.Numerical experiments are carried out to verify the performance of the AHB-AHS method.Five typical nonlinear dynamic equations with different types of nonlinearities and excitations are chosen as the illustrative examples.Compared with the classical HBM and Runge-Kutta methods,the proposed AHB-AHS method is of higher accuracy and better convergence.The AHB-AHS method proposed in this paper has the potential to investigate the nonlinear vibrations of complex high-dimensional nonlinear systems.
基金the China National Funds for Distinguished Young Scholars(No.12025204)。
文摘Eliminating the effects of gravity and designing nonlinear energy sinks(NESs)that suppress vibration in the vertical direction is a challenging task with numerous damping requirements.In this paper,the dynamic design of a vertical track nonlinear energy sink(VTNES)with zero linear stiffness in the vertical direction is proposed and realized for the first time.The motion differential equations of the VTNES coupled with a linear oscillator(LO)are established.With the strong nonlinearity considered of the VTNES,the steady-state response of the system is analyzed with the harmonic balance method(HBM),and the accuracy of the HBM is verified numerically.On this basis,the VTNES prototype is manufactured,and its nonlinear stiffness is identified.The damping effect and dynamic characteristics of the VTNES are studied theoretically and experimentally.The results show that the VTNES has better damping effects when strong modulation responses(SMRs)occur.Moreover,even for small-amplitude vibration,the VTNES also has a good vibration suppression effect.To sum up,in order to suppress the vertical vibration,an NES is designed and developed,which can suppress the vertical vibration within certain ranges of the resonance frequency and the vibration intensity.
基金National Natural Science Foundation of China(51976172)National Science and Technology Major Project (2017-II-0009-0023)+1 种基金China’s 111 project(B17037)Innovation Foundation for Doctor Dissertation of Northwestern Polytechnical University(CX2023056)。
文摘The time domain harmonic balance method is an attractive reduced order method of analyzing unsteady flow for turbomachines. However, the method can admit non-physical solutions. Non-physical solutions were encountered from a three-blade-row compressor configuration in a time domain harmonic balance analysis. This paper aims to investigate the root cause of the non-physical solutions. The investigation involves several strategies, which include increasing the number of harmonics, increasing the number of time instants, including scattered modes,including the rotor-rotor interaction, and the use of a new method-the approximate time domain nonlinear harmonic method. Numerical analyses pertinent to each strategy are presented to reveal the root cause of the non-physical solution. It is found that the nonlinear interaction of unsteady flow components with different fundamental frequencies is the cause of the non-physical solution. The non-physical solution can be eliminated by incorporating extra scattered modes or using the approximate time domain nonlinear harmonic method.
基金supported by the National Natural Science Foundation of China(No.10632040)
文摘Comparisons of the common methods for obtaining the periodic responses show that the harmonic balance method with alternating frequency/time （HB-AFT） do- main technique has some advantages in dealing with nonlinear problems of fractional exponential models. By the HB-AFT method, a rigid rotor supported by ball bearings with nonlinearity of Hertz contact and ball passage vibrations is considered. With the aid of the Floquet theory, the movement characteristics of interval stability are deeply studied. Besides, a simple strategy to determine the monodromy matrix is proposed for the stability analysis.
基金supported by the National Natural Science Foundation of China (10772202)Doctoral Program Foundation of Ministry of Education of China (20050558032)Guangdong Province Natural Science Foundation (07003680, 05003295)
文摘We have deduced incremental harmonic balance an iteration scheme in the （IHB） method using the harmonic balance plus the Newton-Raphson method. Since the convergence of the iteration is dependent upon the initial values in the iteration, the convergent region is greatly restricted for some cases. In this contribution, in order to enlarge the convergent region of the IHB method, we constructed the zeroth-order deformation equation using the homotopy analysis method, in which the IHB method is employed to solve the deformation equation with an embedding parameter as the active increment. Taking the Duffing and the van der Pol equations as examples, we obtained the highly accurate solutions. Importantly, the presented approach renders a convenient way to control and adjust the convergence.
基金the Project of the National Natural Science Foudation of China (Grant No.41372114,41340005,41172162,40972083)
文摘We applied the material balance principle of the denudation volume and sedimentary flux to study the denudation-accumulation system between the Longmen Mountains （Mts.） and the foreland basin. The amount of sediment in each sedimentation stage of the basin was estimated to obtain the denudation volume, erosion thickness and deposit thickness since the Late Triassic Epoch, to enable us to recover the paleoelevation of the provenance and the sedimentary area. The results show the following： （1） Since the Late Triassic Epoch, the elevation of the surface of the Longmen Mts. has uplifted from 0 m to 2751 m, and the crust of the Longmen Mts. has uplifted by 9.8 km. Approximately 72% of the materials introduced have been denuded from the mountains. （2） It is difficult to recover the paleoelevation of each stage of the Longmen Mts. foreland basin quantitatively by the present-day techniques and data. （3） The formation of the Longmen Mts. foreland basin consisted of three stages of thrust belt tectonic load and three stages of thrust belt erosional unload. During tectonic loading stages （Late Triassic Epoch, Late Jurassic-Early Cretaceous, Late Cretaceous-Miocene）, the average elevation of Longmen Mts. was lower （approximately 700-1700 m）. During erosional unloading stages （Early and Middle Jurassic, Middle Cretaceous and Jiaguan, Late Cenozoic）, the average elevation of Longmen Mts. was high at approximately 2000-2800m.
基金Supported by the National Natural Science Foundation of China under Grant No. 11071209the Natural Science Foundation of the Higher Education Institutions of Jiangsu Province under Grant No. 10KJBll0011
文摘A modified homogeneous balance method is proposed by improving some key steps in the homogeneousbalance method.Bilinear equations of some nonlinear evolution equations are derived by using the modified homogeneousbalance method.Generalized Boussinesq equation,KP equation,and mKdV equation are chosen as examples to illustrateour method.This approach is also applicable to a large variety of nonlinear evolution equations.
基金Project supported by the Ph. D. Programs Foundation of Ministry of Education of China (No.20050558032) the Natural Science Foundation of Guangdong Province of China (No.05003295) the Foundation of Sun Yat-sen University Advanced Research Center (No.06M8) the Young Teacher Scientific Research Foundation of Sun Sat-sen University (No.1131011)
文摘The incremental harmonic balance method was extended to analyze the flutter of systems with multiple structural strong nonlinearities. The strongly nonlinear cubic plunging and pitching stiffness terms were considered in the flutter equations of two-dimensional airfoil. First, the equations were transferred into matrix form, then the vibration process was divided into the persistent incremental processes of vibration moments. And the expression of their solutions could be obtained by using a certain amplitude as control parameter in the harmonic balance process, and then the bifurcation, limit cycle flutter phenomena and the number of harmonic terms were analyzed. Finally, numerical results calculated by the Runge-Kutta method were given to verify the results obtained by the proposed procedure. It has been shown that the incremental harmonic method is effective and precise in the analysis of strongly nonlinear flutter with multiple structural nonlinearities.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11872254 and 11672191)
文摘The dynamical properties of fractional-order Duffing–van der Pol oscillator are studied, and the amplitude–frequency response equation of primary resonance is obtained by the harmonic balance method. The stability condition for steady-state solution is obtained based on Lyapunov theory. The comparison of the approximate analytical results with the numerical results is fulfilled, and the approximations obtained are in good agreement with the numerical solutions. The bifurcations of primary resonance for system parameters are analyzed. The results show that the harmonic balance method is effective and convenient for solving this problem, and it provides a reference for the dynamical analysis of similar nonlinear systems.
基金Supported by the National Nature Science Foundation of China(10371070)Supported by the Nature Science Foundation of Educational Committee of Liaoning Province(2021401157)
文摘Based on the homogenous balance method and with the help of mathematica, the Backlund transformation and the transfer heat equation are derived. Analyzing the heat-transfer equation, the multiple soliton solutions and other exact analytical solution for Whitham-Broer-Kaup equations(WBK) are derived. These solutions contain Fan's, Xie's and Yan's results and other new types of analytical solutions, such as rational function solutions and periodic solutions. The method can also be applied to solve more nonlinear differential equations.
基金Foundation item： Supported by the National Natural Science Foundation of China（10671182） Supported by the Foundation and Frontier Technology Research of Henan（082300410060）
文摘In this paper, we present a solution methodology to obtain exact solutions of some nonlinear evolution equation by modifying the homogeneous balance method. Based on the modified homogeneous balance method, several kinds of exact（new） solutions of the generalized KdV equation are obtained.
文摘In this paper, the Auto-B?cklund transformation connected with the homogeneous balance method (HB) and the extended tanh-function method are used to construct new exact solutions for the time-dependent coefficients Calogero-Degasperis (VCCD) equation. New soliton and periodic solutions of many types are obtained. Furthermore, the soliton propagation is discussed under the effect of the variable coefficients.
基金Project supported by the National Natural Science Foundation of China(No.12002195)the Pujiang Project of Shanghai Science and Technology Commission of China(No.20PJ1404000)。
文摘The coupling vibration of a hydraulic pipe system consisting of two pipes is studied.The pipes are installed in parallel and fixed at their ends,and are restrained by clips to one bracket at their middle points.The pipe subjected to the basement excitation at the left end is named as the active pipe,while the pipe without excitation is called the passive pipe.The clips between the two pipes are the bridge for the vibration energy.The adjacent natural frequencies will enhance the vibration coupling.The governing equation of the coupled system is deduced by the generalized Hamilton principle,and is discretized to the modal space.The modal correction is used during the discretization.The investigation on the natural characters indicates that the adjacent natural frequencies can be adjusted by the stiffness of the two clips and bracket.The harmonic balance method(HBM)is used to study the responses in the adjacent natural frequency region.The results show that the vibration energy transmits from the active pipe to the passive pipe swimmingly via the clips together with a flexible bracket,while the locations of them are not node points.The adjacent natural frequencies may arouse wide resonance curves with two peaks for both pipes.The stiffness of the clip and bracket can release the vibration coupling.It is suggested that the stiffness of the clip on the passive pipe should be weak and the bracket should be strong enough.In this way,the vibration energy is reflected by the almost rigid bracket,and is hard to transfer to the passive pipe via a soft clip.The best choice is to set the clips at the pipe node points.The current work gives some suggestions for weakening the coupled vibration during the dynamic design of a coupled hydraulic pipe system.
基金Project supported by the National Natural Science Foundation of China(Nos.12272240 and12022213)。
文摘In this study,a coupling model of fluid-conveying pipes made of functionally graded materials(FGMs)with NiTiNOL-steel(NiTi-ST)for vibration absorption is investigated.The vibration responses of the FGM fluid-conveying pipe with NiTi-ST are studied by the Galerkin truncation method(GTM)and harmonic balance method(HBM).The harmonic balance solutions and the numerical results are consistent.Also,the linearized stability of the structure is determined.The effects of the structure parameters on the absorption performance are also studied.The results show that the NiTi-ST is an effective means of vibration absorption.Furthermore,in studying the effect of the NiTi-ST,a closed detached response(CDR)is first observed.It is noteworthy that the CDR may dramatically change the vibration amplitude and that the parameters of the NiTi-ST may determine the emergence or disappearance of the CDR.This vibration absorption device can be extended to offer more general vibration control in engineering applications.
基金supported by a grant of the Korea Health Technology R&D Project through the Korea Health Industry Development Institute(KHIDI)funded by the Ministry of Health&Welfare,Republic of Korea(Grant Number:HI21C1831)the Soonchunhyang University Research Fund.
文摘Wireless Sensor Network(WSN)technology is the real-time applica-tion that is growing rapidly as the result of smart environments.Battery power is one of the most significant resources in WSN.For enhancing a power factor,the clustering techniques are used.During the forward of data in WSN,more power is consumed.In the existing system,it works with Load Balanced Cluster-ing Method(LBCM)and provides the lifespan of the network with scalability and reliability.In the existing system,it does not deal with end-to-end delay and deliv-ery of packets.For overcoming these issues in WSN,the proposed Genetic Algo-rithm based on Chicken Swarm Optimization(GA-CSO)with Load Balanced Clustering Method(LBCM)is used.Genetic Algorithm generates chromosomes in an arbitrary method then the chromosomes values are calculated using Fitness Function.Chicken Swarm Optimization(CSO)helps to solve the complex opti-mization problems.Also,it consists of chickens,hens,and rooster.It divides the chicken into clusters.Load Balanced Clustering Method(LBCM)maintains the energy during communication among the sensor nodes and also it balances the load in the gateways.The proposed GA-CSO with LBCM improves the life-span of the network.Moreover,it minimizes the energy consumption and also bal-ances the load over the network.The proposed method outperforms by using the following metrics such as energy efficiency,ratio of packet delivery,throughput of the network,lifetime of the sensor nodes.Therefore,the evaluation result shows the energy efficiency that has achieved 83.56%and the delivery ratio of the packet has reached 99.12%.Also,it has attained linear standard deviation and reduced the end-to-end delay as 97.32 ms.
