One of the most important parameter used for the evaluation of the energy rating of PV modules is, their spectral responsivities which are the measure of electrical performance parameters per incident solar radiation....One of the most important parameter used for the evaluation of the energy rating of PV modules is, their spectral responsivities which are the measure of electrical performance parameters per incident solar radiation. In this work, spectral responsivity measurements of a mono-crystalline, a poly-crystalline, a CIGS thin film and a bifacial module were measured using xenon-based flash type solar simulator system and a set of band pass filters. For the comprehensive characterization of parameters that may influence the spectral responsivity measurements, initially the simulator system was characterized both optically and thermally according to the IEC60904-9 and IEC60891 standard requirements. The optical characterizations in terms of spectral match, spatial non-uniformity and temporal instability indicate that the measured results (~3.0%, ~0.30% and ~0.20%) according to the IEC 60904-9 standard’s classification requirements correspond to A+A+A+ classes. Moreover, thermal characterizations in terms of the temperature uniformity show that over the 2 × 2 m area temperature uniformity of simulator system’s light distribution (1ºC) is almost two times better than the IEC 60891 standard requirements (±2ºC). Next, PV modules were electrically stabilized according to the IEC 61215-2 standard requirement’s (stability test) to reduce the fluctuations in their electrical performance parameters. Then, using the band pass filters, temperature controlled xenon-based solar simulator system and a reference PV module of the spectral responsivity of PV modules were measured from 400 nm to 1100 nm with 50 nm steps with relative uncertainty of 10<sup>-3</sup> level.展开更多
Software Defined Radio (SDR) architecture allows us to integrate different mobile technologies using common hardware but with different software modules. To achieve this, we need to keep the signal in digital form for...Software Defined Radio (SDR) architecture allows us to integrate different mobile technologies using common hardware but with different software modules. To achieve this, we need to keep the signal in digital form for as much portion of the circuitry as possible, so that the implementation could be carried out by programmable digital processors. For this purpose, the incoming radio frequency (RF) signal is down converted to baseband spectrum using band pass sampling method. Research works carried out so far in this field have developed a few algorithms for band pass sampling. But, these algorithms are not much useful for most of the mobile communication systems and they use complex methodology for computing the sampling frequency values. In order to use the SDR platform to integrate all current wireless technologies, an efficient, cost effective and less complex algorithm that can be labelled as universal band pass sampling algorithm is developed in this paper for multiple mobile systems. This algorithm is based on a novel idea of inserting guard bands between the signals which reduces the design complexities of perfect ADC and sharp cut off filters. Using this algorithm, valid sampling frequency ranges and corresponding IF values are calculated for down converting RF signals. The algorithm is tested for six RF signals of different wireless technologies which are integrated and simultaneously down converted using SDR based front end receiver and thus the system multiplies the base station capacity by a factor of six. The simulation results are obtained and shown in this paper which proves that the algorithm developed works well for most of the wireless technologies.展开更多
A new technique for the conversion of ladder based filter into CFOA based filter has been proposed. The technique uses signal flow graph and converts the existing LC ladder based filter into band pass & band stop ...A new technique for the conversion of ladder based filter into CFOA based filter has been proposed. The technique uses signal flow graph and converts the existing LC ladder based filter into band pass & band stop configurations. The design of band pass and band stop filter has been realized using the proposed technique. The proposed configuration is implemented using CFOA as an active device and all the capacitors are grounded. CFOA based circuits have greater linearity, high dynamic rate, high slew rate and high signal bandwidth. Simulation has been carried out using simulation software P Spice (v10.1). The simulation results have been demonstrated and discussed.展开更多
Novel accurate and efficient equivalent circuit trained artificial neural-network (EC-ANN) models,which inherit and improve upon EC model and EM-ANN models' advantages,are developed for coplanar waveguide (CPW) d...Novel accurate and efficient equivalent circuit trained artificial neural-network (EC-ANN) models,which inherit and improve upon EC model and EM-ANN models' advantages,are developed for coplanar waveguide (CPW) discontinuities. Modeled discontinuities include : CPW step, interdigital capacitor, symmetric cross junction, and spiral inductor, for which validation tests are performed. These models allow for circuit design, simulation, and optimization within a CAD simulator. Design and realization of a coplanar lumped element band pass filter on GaAs using the developed CPW EC-ANN models are demonstrated.展开更多
This paper presents a low power tunable active inductor and RF band pass filter suitable for multiband RF front end circuits. The active inductor circuit uses the PMOS cascode structure as the negative transconductor ...This paper presents a low power tunable active inductor and RF band pass filter suitable for multiband RF front end circuits. The active inductor circuit uses the PMOS cascode structure as the negative transconductor of a gyrator to reduce the noise voltage. Also, this structure provides possible negative resistance to reduce the inductor loss with wide inductive bandwidth and high resonance frequency. The RF band pass filter is realized using the proposed active inductor with suitable input and output buffer stages. The tuning of the center frequency for multiband operation is achieved through the controllable current source. The designed active inductor and RF band pass filter are simulated in 180 nm and 45 nm CMOS process using the Synopsys HSPICE simulation tool and their performances are compared. The parameters, such as resonance frequency, tuning capability, noise and power dissipation, are analyzed for these CMOS technologies and discussed. The design of a third order band pass filter using an active inductor is also presented.展开更多
文摘One of the most important parameter used for the evaluation of the energy rating of PV modules is, their spectral responsivities which are the measure of electrical performance parameters per incident solar radiation. In this work, spectral responsivity measurements of a mono-crystalline, a poly-crystalline, a CIGS thin film and a bifacial module were measured using xenon-based flash type solar simulator system and a set of band pass filters. For the comprehensive characterization of parameters that may influence the spectral responsivity measurements, initially the simulator system was characterized both optically and thermally according to the IEC60904-9 and IEC60891 standard requirements. The optical characterizations in terms of spectral match, spatial non-uniformity and temporal instability indicate that the measured results (~3.0%, ~0.30% and ~0.20%) according to the IEC 60904-9 standard’s classification requirements correspond to A+A+A+ classes. Moreover, thermal characterizations in terms of the temperature uniformity show that over the 2 × 2 m area temperature uniformity of simulator system’s light distribution (1ºC) is almost two times better than the IEC 60891 standard requirements (±2ºC). Next, PV modules were electrically stabilized according to the IEC 61215-2 standard requirement’s (stability test) to reduce the fluctuations in their electrical performance parameters. Then, using the band pass filters, temperature controlled xenon-based solar simulator system and a reference PV module of the spectral responsivity of PV modules were measured from 400 nm to 1100 nm with 50 nm steps with relative uncertainty of 10<sup>-3</sup> level.
文摘Software Defined Radio (SDR) architecture allows us to integrate different mobile technologies using common hardware but with different software modules. To achieve this, we need to keep the signal in digital form for as much portion of the circuitry as possible, so that the implementation could be carried out by programmable digital processors. For this purpose, the incoming radio frequency (RF) signal is down converted to baseband spectrum using band pass sampling method. Research works carried out so far in this field have developed a few algorithms for band pass sampling. But, these algorithms are not much useful for most of the mobile communication systems and they use complex methodology for computing the sampling frequency values. In order to use the SDR platform to integrate all current wireless technologies, an efficient, cost effective and less complex algorithm that can be labelled as universal band pass sampling algorithm is developed in this paper for multiple mobile systems. This algorithm is based on a novel idea of inserting guard bands between the signals which reduces the design complexities of perfect ADC and sharp cut off filters. Using this algorithm, valid sampling frequency ranges and corresponding IF values are calculated for down converting RF signals. The algorithm is tested for six RF signals of different wireless technologies which are integrated and simultaneously down converted using SDR based front end receiver and thus the system multiplies the base station capacity by a factor of six. The simulation results are obtained and shown in this paper which proves that the algorithm developed works well for most of the wireless technologies.
文摘A new technique for the conversion of ladder based filter into CFOA based filter has been proposed. The technique uses signal flow graph and converts the existing LC ladder based filter into band pass & band stop configurations. The design of band pass and band stop filter has been realized using the proposed technique. The proposed configuration is implemented using CFOA as an active device and all the capacitors are grounded. CFOA based circuits have greater linearity, high dynamic rate, high slew rate and high signal bandwidth. Simulation has been carried out using simulation software P Spice (v10.1). The simulation results have been demonstrated and discussed.
文摘Novel accurate and efficient equivalent circuit trained artificial neural-network (EC-ANN) models,which inherit and improve upon EC model and EM-ANN models' advantages,are developed for coplanar waveguide (CPW) discontinuities. Modeled discontinuities include : CPW step, interdigital capacitor, symmetric cross junction, and spiral inductor, for which validation tests are performed. These models allow for circuit design, simulation, and optimization within a CAD simulator. Design and realization of a coplanar lumped element band pass filter on GaAs using the developed CPW EC-ANN models are demonstrated.
文摘This paper presents a low power tunable active inductor and RF band pass filter suitable for multiband RF front end circuits. The active inductor circuit uses the PMOS cascode structure as the negative transconductor of a gyrator to reduce the noise voltage. Also, this structure provides possible negative resistance to reduce the inductor loss with wide inductive bandwidth and high resonance frequency. The RF band pass filter is realized using the proposed active inductor with suitable input and output buffer stages. The tuning of the center frequency for multiband operation is achieved through the controllable current source. The designed active inductor and RF band pass filter are simulated in 180 nm and 45 nm CMOS process using the Synopsys HSPICE simulation tool and their performances are compared. The parameters, such as resonance frequency, tuning capability, noise and power dissipation, are analyzed for these CMOS technologies and discussed. The design of a third order band pass filter using an active inductor is also presented.