氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过...氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过浸渍法制备了不同Ru负载量(质量分数分别为0.5%、1.0%和2.0%)的催化剂(分别为0.5%Ru/Si_(3)N_(4)、1.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)),并以商品氮化硅(Si_(3)N_(4)-C)为载体制备了2.0%Ru/Si_(3)N_(4)-C催化剂作为对照组。表征了催化剂的理化性质,测试了其在300℃、0.1 MPa下的CO_(2)加氢反应活性。结果显示,与Si_(3)N_(4)-C相比,Si_(3)N_(4)的比表面积较高(502 m^(2)/g),Si_(3)N_(4)作为载体显著提高了金属分散度,降低了金属粒径,催化剂暴露出更多的活性位点。0.5%Ru/Si_(3)N_(4)的金属粒径较小,展现出强的H_(2)吸附能力,H难以解吸,抑制了中间物种CO加氢生成CH_(4)。随着Ru负载量增加,金属粒径增大,催化剂的CH_(4)选择性更好。Ru/Si_(3)N_(4)系列催化剂中,2.0%Ru/Si_(3)N_(4)的CH_(4)选择性较高(98.8%)。空速为10000 m L/(g·h)时,0.5%Ru/Si_(3)N_(4)的CO选择性为88.2%。与2.0%Ru/Si_(3)N_(4)相比,2.0%Ru/Si_(3)N_(4)-C的金属粒径更大,活性位点较少,活性更低。2.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)-C的CO_(2)转化率分别为53.1%和9.2%。Si_(3)N_(4)有效提高了金属分散度,提高了催化剂的CO_(2)加氢反应活性;通过调控Ru负载量控制催化剂金属粒径,可实现对产物CO或CH_(4)选择性的调控。展开更多
This study examines the impact of different CO<sub>2</sub> injection methods on coalbed methane recovery. Specifically, this study investigated the effectiveness of continuously injecting CO<sub>2<...This study examines the impact of different CO<sub>2</sub> injection methods on coalbed methane recovery. Specifically, this study investigated the effectiveness of continuously injecting CO<sub>2</sub> versus injecting CO<sub>2</sub> that had been soaked for two weeks. The objective was to ascertain which approach was more successful in enhancing CO<sub>2</sub> Enhanced coalbed Methane (CO<sub>2</sub>-ECBM). The experiment involved injecting 3 MPa of CH<sub>4</sub> into dry coal samples, allowing it to adsorb until reaching equilibrium, and then injecting 5 MPa of CO<sub>2</sub> to recover adsorbed CH<sub>4</sub>. The continuous method recovered CH<sub>4</sub> without detectable effluent concentration for 5 hours, but desorption efficiency was only 26% due to fast flow. On the other hand, the desorption efficiency of the cyclic method was only 12%, indicating trapped CH<sub>4</sub>. A comparison of desorption efficiency per unit of time shows the continuous method is more effective than the cyclic method. The results of this study demonstrate the continuous method is more effective for the desorption of CH<sub>4</sub>, and its efficiency can be improved by briefly soaking CO<sub>2</sub> on coal and then reinjecting it to maximize CH<sub>4</sub> recovery. It is advisable to limit the soaking time to prevent excessive swelling of the coal matrix, which can hinder seam flow and harm long-term gas production.展开更多
The experimental research programs of 1950s, to understand the adsorption of CO on W surfaces, changed to ab initio studies in 2000s. The goals were to seek improved practical applications. Most of the studies were ba...The experimental research programs of 1950s, to understand the adsorption of CO on W surfaces, changed to ab initio studies in 2000s. The goals were to seek improved practical applications. Most of the studies were based on density functional theory. Many studies also used programs, such as VASP (Vienna Abinitio simulation package) and CPMD. The computational procedures used plane wave approximations. This needed studies with selection of K points and cutoff energy selection to assure convergence in energy calculations. Observations and analysis of papers published from 2006 to 2022 indicate that the cutoff energies were selected arbitrarily without any needed convergence studies. By selecting a published 2006 paper, this paper has clearly showed that an arbitrary selection of cutoff energy, such as 460 eV, is not in the range of, cutoff energies that assure convergence of energy calculations, with ab initio methods and have indicated correction procedures. .展开更多
文摘氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过浸渍法制备了不同Ru负载量(质量分数分别为0.5%、1.0%和2.0%)的催化剂(分别为0.5%Ru/Si_(3)N_(4)、1.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)),并以商品氮化硅(Si_(3)N_(4)-C)为载体制备了2.0%Ru/Si_(3)N_(4)-C催化剂作为对照组。表征了催化剂的理化性质,测试了其在300℃、0.1 MPa下的CO_(2)加氢反应活性。结果显示,与Si_(3)N_(4)-C相比,Si_(3)N_(4)的比表面积较高(502 m^(2)/g),Si_(3)N_(4)作为载体显著提高了金属分散度,降低了金属粒径,催化剂暴露出更多的活性位点。0.5%Ru/Si_(3)N_(4)的金属粒径较小,展现出强的H_(2)吸附能力,H难以解吸,抑制了中间物种CO加氢生成CH_(4)。随着Ru负载量增加,金属粒径增大,催化剂的CH_(4)选择性更好。Ru/Si_(3)N_(4)系列催化剂中,2.0%Ru/Si_(3)N_(4)的CH_(4)选择性较高(98.8%)。空速为10000 m L/(g·h)时,0.5%Ru/Si_(3)N_(4)的CO选择性为88.2%。与2.0%Ru/Si_(3)N_(4)相比,2.0%Ru/Si_(3)N_(4)-C的金属粒径更大,活性位点较少,活性更低。2.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)-C的CO_(2)转化率分别为53.1%和9.2%。Si_(3)N_(4)有效提高了金属分散度,提高了催化剂的CO_(2)加氢反应活性;通过调控Ru负载量控制催化剂金属粒径,可实现对产物CO或CH_(4)选择性的调控。
文摘This study examines the impact of different CO<sub>2</sub> injection methods on coalbed methane recovery. Specifically, this study investigated the effectiveness of continuously injecting CO<sub>2</sub> versus injecting CO<sub>2</sub> that had been soaked for two weeks. The objective was to ascertain which approach was more successful in enhancing CO<sub>2</sub> Enhanced coalbed Methane (CO<sub>2</sub>-ECBM). The experiment involved injecting 3 MPa of CH<sub>4</sub> into dry coal samples, allowing it to adsorb until reaching equilibrium, and then injecting 5 MPa of CO<sub>2</sub> to recover adsorbed CH<sub>4</sub>. The continuous method recovered CH<sub>4</sub> without detectable effluent concentration for 5 hours, but desorption efficiency was only 26% due to fast flow. On the other hand, the desorption efficiency of the cyclic method was only 12%, indicating trapped CH<sub>4</sub>. A comparison of desorption efficiency per unit of time shows the continuous method is more effective than the cyclic method. The results of this study demonstrate the continuous method is more effective for the desorption of CH<sub>4</sub>, and its efficiency can be improved by briefly soaking CO<sub>2</sub> on coal and then reinjecting it to maximize CH<sub>4</sub> recovery. It is advisable to limit the soaking time to prevent excessive swelling of the coal matrix, which can hinder seam flow and harm long-term gas production.
文摘The experimental research programs of 1950s, to understand the adsorption of CO on W surfaces, changed to ab initio studies in 2000s. The goals were to seek improved practical applications. Most of the studies were based on density functional theory. Many studies also used programs, such as VASP (Vienna Abinitio simulation package) and CPMD. The computational procedures used plane wave approximations. This needed studies with selection of K points and cutoff energy selection to assure convergence in energy calculations. Observations and analysis of papers published from 2006 to 2022 indicate that the cutoff energies were selected arbitrarily without any needed convergence studies. By selecting a published 2006 paper, this paper has clearly showed that an arbitrary selection of cutoff energy, such as 460 eV, is not in the range of, cutoff energies that assure convergence of energy calculations, with ab initio methods and have indicated correction procedures. .
