期刊文献+
共找到53篇文章
< 1 2 3 >
每页显示 20 50 100
CSRm束流累积阶段闭轨校正系统设计 被引量:1
1
作者 李维凯 张玮 +1 位作者 殷达钰 安石 《强激光与粒子束》 EI CAS CSCD 北大核心 2019年第3期64-68,共5页
为测量兰州重离子加速器冷却储存环主环(CSRm)束流累积阶段的闭轨畸变并进行闭轨校正,开发了闭轨校正系统,该系统由轨道测量系统、闭轨控制系统和校正磁铁系统构成。轨道测量系统实现对束流轨道的实时监测;闭轨控制系统读取束流轨道信息... 为测量兰州重离子加速器冷却储存环主环(CSRm)束流累积阶段的闭轨畸变并进行闭轨校正,开发了闭轨校正系统,该系统由轨道测量系统、闭轨控制系统和校正磁铁系统构成。轨道测量系统实现对束流轨道的实时监测;闭轨控制系统读取束流轨道信息,然后进行闭轨校正计算,并将计算后的校正值传输给校正磁铁系统;校正磁铁系统通过改变校正电源的值,改变校正磁铁的强度,实现对束流轨道的调整,完成闭轨校正。模拟测试结果表明,束流轨道水平方向的最大畸变由校正前的3.37mm减小为校正后的0.39mm,垂直方向的最大畸变由校正前的4.21mm减小为校正后的0.31mm。该系统能够实现响应矩阵的自动测量和束流轨道的自动校正,满足设计要求。 展开更多
关键词 csrm 闭轨畸变 闭轨校正 响应矩阵
下载PDF
HIRFL-CSRm内靶实验终端CsI(Tl)电磁量能器性能模拟 被引量:3
2
作者 李文飞 徐瑚珊 +12 位作者 孙志宇 肖国青 詹文龙 郭忠言 段利敏 李加兴 徐华根 陈若富 张雪荧 贾飞 祁辉荣 马越 张宏斌 《原子核物理评论》 CAS CSCD 北大核心 2004年第4期309-311,共3页
基于GEANT4模拟了HIRFL CSRm内靶实验终端的CsI(Tl)电磁量能器系统,给出了CsI电磁量能器的最佳设计参数及可能达到的性能.结果表明,设计的CsI(Tl)电磁量能器系统能够满足所研究的物理要求.
关键词 电磁量能器 HIRFL CSR GEANT4 实验 系统 物理
下载PDF
CSRm内靶实验中的轻离子束流寿命模拟研究 被引量:1
3
作者 张雪荧 徐瑚珊 +2 位作者 孙志宇 胡正国 张宏斌 《强激光与粒子束》 EI CAS CSCD 北大核心 2008年第6期1011-1016,共6页
建立了内靶对兰州冷却储存环主环束流影响的单粒子跟踪模拟程序,对pellet小丸靶和碳靶对束流带来的负面影响进行了模拟研究,主要讨论CSRm内靶实验中的束流存活率和束流寿命状态。结果显示利用厚度为1×1016atoms.cm-2小丸内靶时,2.6... 建立了内靶对兰州冷却储存环主环束流影响的单粒子跟踪模拟程序,对pellet小丸靶和碳靶对束流带来的负面影响进行了模拟研究,主要讨论CSRm内靶实验中的束流存活率和束流寿命状态。结果显示利用厚度为1×1016atoms.cm-2小丸内靶时,2.6 GeV质子束流寿命在100 s量级,而对于目前技术水平下的碳膜靶(厚度为5×1017atoms.cm-2),质子束流寿命为s量级;束流寿命和束流能量基本成正比关系,束流寿命和内靶厚度近似成反比关系。 展开更多
关键词 柬流寿命 CSR主环 内靶 束流发射度 接收度 蒙特-卡罗模拟
下载PDF
Magnetic alloy cores for the HIRFL-CSRm compressor cavity 被引量:1
4
作者 MEI Lirong XU Zhe +3 位作者 YUAN Youjin JIN Peng BIAN Zhibin ZHAO Hongwei 《Nuclear Science and Techniques》 SCIE CAS CSCD 2011年第2期118-121,共4页
Four types of magnetic alloy cores,labeled as V1,V2,A1 and A2,were produced by Liyuan Corp.Ltd.,for the radio frequency compression cavity of HIRFL-CSRm.In this work,their permeability,quality factor (Q value) and shu... Four types of magnetic alloy cores,labeled as V1,V2,A1 and A2,were produced by Liyuan Corp.Ltd.,for the radio frequency compression cavity of HIRFL-CSRm.In this work,their permeability,quality factor (Q value) and shunt impedance were measured before installing them into the cavity.The results show that the V1,V2 and A2 have higher permeability and shunt impedance,and lower Q value,and are suitable to the radio frequency compression cavity. 展开更多
关键词 HIRFL csrm 压缩机 磁合金 磁芯 无线电频率 阻抗测量 品质因数
下载PDF
6-24 Study of Heavy-ion-stimulated Gas Desorption Rate in CSRm
5
作者 Chai Zhen Meng Jun +4 位作者 Luo Cheng Li Peng Zheng Wenheng Niu Zhiwei Gao Yanmin 《IMP & HIRFL Annual Report》 2015年第1期296-297,共2页
There is a definite requirement of high vacuum degree in synchrotron accelerator. According to a study[1], the static LEAR vacuum pressure was about 510?12 Torr, but local pressure bumps up to 10?9 Torr occurred duri... There is a definite requirement of high vacuum degree in synchrotron accelerator. According to a study[1], the static LEAR vacuum pressure was about 510?12 Torr, but local pressure bumps up to 10?9 Torr occurred during continuous injection of about 108 ions/s. A dynamic pressure increase was attributed to the outgassing of vacuum equipment due to the impact of lost ions. The ion-induced desorption can seriously limit the ion intensity, luminosity, and beam lifetime of the accelerator. 展开更多
关键词 DESORPTION RATE csrm
下载PDF
6-26 Power Supplies Control for Electron Cooling of CSRm
6
作者 Su Jianjun Wang Yanyu Zhang Jianchuan 《IMP & HIRFL Annual Report》 2015年第1期300-301,共2页
To improve the efficiency of Electron Cooling Control System of CSRm, power supplies control system was designed and set up in September 2015. The control software package is developed with Visual C++, which is able t... To improve the efficiency of Electron Cooling Control System of CSRm, power supplies control system was designed and set up in September 2015. The control software package is developed with Visual C++, which is able to control and monitor all power supplies. In order to prevent the power supplies’ leakage accident which may cause the breakdown of other device, alarm and interlock-protection functions are added to the software and hardware. 展开更多
关键词 ELECTRON COOLING csrm
下载PDF
4-8 Dielectronic Recombination of 112Sn35+ Ions at the CSRm
7
作者 Xu Xin Wang Shuxing +15 位作者 Zhu Linfan Huang Zhongkui Ma Xinwen Wen Weiqiang Wang Hanbing Chuai Xiaoya Dou Lijun Zhu Xiaolong Zhao Dongmei Yuan Youjin Mao Lijun Li Jie Ma Xiaoming Yan Tailai Yang Jiancheng Xia Jiawen 《IMP & HIRFL Annual Report》 2015年第1期202-202,共1页
The total recombination rate coefficient of Phosphorus-like 112Sn35+ have been measured at the main cooler storage ring (CSRm) employing the electron-ion merged-beams technique. The Phosphorus-like 112Sn35+ ions were ... The total recombination rate coefficient of Phosphorus-like 112Sn35+ have been measured at the main cooler storage ring (CSRm) employing the electron-ion merged-beams technique. The Phosphorus-like 112Sn35+ ions were injected into the CSRm at an energy of 3.7 MeV/u with a typical current of 50 eA, and the momentum spread of the ion beam is 210?4 after several seconds of cooling. 展开更多
关键词 112Sn35+ IONS csrm
下载PDF
Measurements of CSRm Quadrupoles
8
作者 He Yuan, Liu Weijun, Zhang Bin, Han Shaofei, Ma Lizhen, Su Yalong Zhang Siling and Yuan Ping 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2003年第1期132-132,共1页
There are 30 quadruples in main ring of CSR. Its parameters are listed in Table 1. All of them were manufactured and tested last yeal.
关键词 csrm 四极 测量方法 有效长度 离子磁饱和度 谐波场
下载PDF
Vacuum System in CSRm Commissioning
9
作者 Yang Xiaotian Zhang Junhui Meng Jun Hu Zhenjun Zhang Xiping Hou Shengjun Guo Dizhou Yang Weishun Wu Huimin Zhang Xinjun 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2006年第1期141-141,共1页
关键词 真空系统 试车 csrm系统 加速器
下载PDF
Progress of CSRm Vacuum System in 2004
10
作者 Vacuum Group 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2004年第1期147-147,共1页
Great progress was achieved in CSRm vacuum system in the year of 2004. All of the components have been fixed to the system. After mechanic adjustment, baking-out on line, average vacuum degree of CSRm was up to better... Great progress was achieved in CSRm vacuum system in the year of 2004. All of the components have been fixed to the system. After mechanic adjustment, baking-out on line, average vacuum degree of CSRm was up to better than 5×10-10 Pa. In this paper, the mechanic installation and adjustment, fix of baking system, process of pumping and result are introduced. 展开更多
关键词 真空系统 csrm 企业社会责任 宾夕法尼亚州 烘烤系统 真空度 机械 调整
下载PDF
Pellet Target- a novel internal target at CSRm
11
作者 Li Zhankui and Xu Hushan 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2004年第1期175-176,共2页
The internal targets used in the storage ring are quite promising targets due to the well defined reaction vertex, low background and undisturbed reaction products. Light-isotope targets, such as hydrogen and deuteriu... The internal targets used in the storage ring are quite promising targets due to the well defined reaction vertex, low background and undisturbed reaction products. Light-isotope targets, such as hydrogen and deuterium, are the most favorite candidates for hadron physics study. For physical experiments, the figure of merit is usually the luminosity, and it is found that the frozen micro-spheres (called pellets) could provide a high luminosity which is comparable to that of an external target, whereas the conventional gas targets can not reach this criterion because of the heavy gas load in the reaction chamber. A global detector with nearly '4 configuration can be arranged around the pellet target. In the near future, a pellet target facility with global detectors is foreseen at CSRm in Lanzhou. 展开更多
关键词 csrm 内靶 球团 反应产物 强子物理 物理实验 高亮度 探测器
下载PDF
Estimated Maximum Luminosity for Pellet Internal Target at CSRm
12
作者 Li Zhankui and Xu Hushan 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2004年第1期174-175,共2页
A pellet target facility with global detectors will be constructed at CSRm, Lanzhou for hadron physics research. The pellet diameter ranges from 25 to 35 μm, and thus an effective target thickness of 1015 - 1016 atom... A pellet target facility with global detectors will be constructed at CSRm, Lanzhou for hadron physics research. The pellet diameter ranges from 25 to 35 μm, and thus an effective target thickness of 1015 - 1016 atoms/cm2 is expected. The number of stored particles in CSRm is estimated to be 1×109 particles per cycle with the existing accelerator(s) as the injector. With the aid of a planned booster as the injector, the maximum stored particles per cycle can be elevated to 1×1012. The revolution frequency is typically in the order of 1 MHz for the present CSRm ring with a circumference of 161.0 m. With the new booster, a maximum experimental luminosity for pellet target is estimated to be 1×1034/(cm2·s). 展开更多
关键词 csrm 估计 内靶 球团 亮度 颗粒直径 粒子加速器 强子物理
下载PDF
Kicker Vacuum System on CSRm
13
作者 Zhang Junhui Zhao Yugang Hu Zhenjun Hou Shengjun 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2006年第1期143-143,共1页
关键词 csrm系统 真空系统 Kicker磁铁 重离子加速器
下载PDF
Event Generator for Hadron Physics Programs at HIRFL-CSRm
14
作者 Zheng Chuan Yuan Xiaohua Xiao Zhigang Xu Hushan Wang Jiansong Yue Ke Ouyang Zhen Cao Xu Zhang Yapeng 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2009年第1期56-56,共1页
关键词 兰州重离子加速器 强子物理 csrm 事件 介质效应 聚丙烯
下载PDF
Elementary Application of Schottky Probe in CSRm Commissioning
15
作者 Zheng Jianhua, Xiao Guoqing, Mao Ruishi, Zhao Tiecheng, Wang Yanmou Ying Yan, Ma Weinian, Song Haihong and Wu Junxia 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2005年第1期136-136,共1页
Schottky signal analysis plays an important role in the HIRFL-CSR beam diagnostic system. The beam dynamic characteristic in the cooling storage ring is measured with the schottky probes. The relative momentum spread... Schottky signal analysis plays an important role in the HIRFL-CSR beam diagnostic system. The beam dynamic characteristic in the cooling storage ring is measured with the schottky probes. The relative momentum spreadΔp/p of the beam, the value of the tune Q, the revolution frequency of particles along the ring circumference and particle number can be acquired by the Schottky signal. Two Schottky 展开更多
关键词 csrm 肖特基 兰州重离子加速器 应用 调试 束流诊断系统 信号分析 冷却储存环
下载PDF
Building up of CSRm Vacuum Baking-out System
16
作者 Zhang Xiping and Hu Zhenjun 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2004年第1期149-149,共1页
The project of the HIRPL-CSR is being done and the CSRm vacuum system was finished in March 2004. In order to meet the requirement of the beam storage time in HIRFL-CSR storage ring, the average vacuum degree of 6... The project of the HIRPL-CSR is being done and the CSRm vacuum system was finished in March 2004. In order to meet the requirement of the beam storage time in HIRFL-CSR storage ring, the average vacuum degree of 6×10-9 Pa is requested in the ultra-high vacuum system. To reach the target, the vacuum baking-out system must be set up on the system so as to make it baked to about 250℃after the system being exposed to the atmosphere. The vacuum baking-out system main by consists of the thermal sensors, heating jackets (Fig.1), baking-out control system and so on. 展开更多
关键词 真空烘烤 csrm 兰州重离子加速器 超高真空系统 存储时间 热传感器 控制系统 储存环
下载PDF
Radiation Monitoring System of HIRFL-CSRm
17
作者 Li Wuyuan, Su Youwu and Li Zongqiang 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2004年第1期180-180,共1页
The radiation monitoring system of HIRFL-CSRm was composed of neutron and 7 detector, data acquisition and procession system(Fig.1). Fig.2 gives the monitoring sites distribution layout of HIRFL-CSRm. The data obtaine... The radiation monitoring system of HIRFL-CSRm was composed of neutron and 7 detector, data acquisition and procession system(Fig.1). Fig.2 gives the monitoring sites distribution layout of HIRFL-CSRm. The data obtained from detectors were input into a local computer through a PCL-836 counter card, at where the data were processed and the dose rate was obtained. The processed data were upload to the local network, a 展开更多
关键词 兰州重离子加速器 辐射监测系统 csrm 网络服务器 数据采集 分布格局 数据输入 数据上传
下载PDF
Atomic Physics:First Test Experiment Performed at Electron Cooler of CSRm
18
作者 Ma Xinwen Meng Linjie Liu Huiping Xia Jiawen Xu Hushan Hu Zhengguo Yang Xiaodong Wang Men Mao Ruishi Zhang Dachen Mao Lijun Li Jie Li Guohong Yang Jianchen Yuan Youjin Zheng Jianhua Xiao Guoqing Zhan Wenlong 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2008年第1期109-109,111,共2页
关键词 电子束能量 测试实验 csrm 原子物理 冷却器 高电荷态离子 企业社会责任 粒子探测器
下载PDF
Longitudinal Cooling Force Measurements in HIRFL-CSRm
19
作者 Mao Lijun Yang Xiaodong Xia Jiawen Li Jie Li Guohong Yuan Youjin Liu Yong Yang Jiancheng Xiao Chen Li Ke Tian Maohui Li Pen 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2008年第1期143-144,共2页
关键词 兰州重离子加速器 电子冷却装置 csrm 力测量 实时频谱分析仪 电子参数 电子能量 冷却技术
下载PDF
CSRm Injection Beam Line Vacuum System
20
作者 Meng Jun, Yang Xiaotian, Hao Binggan,Wu Huimin, Hou Shengjun and Hu Zhenjun 《近代物理研究所和兰州重离子加速器实验室年报:英文版》 2004年第1期148-148,共1页
CSRm injection beam line is the transitional section between HIRFL post beam line and CSRm. HIRFL post beam line's vacuum degree is about 10-6 Pa and CSRm's designed average pressure is 6×10-9 Pa, so CSRm... CSRm injection beam line is the transitional section between HIRFL post beam line and CSRm. HIRFL post beam line's vacuum degree is about 10-6 Pa and CSRm's designed average pressure is 6×10-9 Pa, so CSRm injection beam line is a very important section which must finish three order of magnitudes pressure transition from 10-9 to 10-6 Pa. 展开更多
关键词 csrm 真空系统 兰州重离子加速器 平均压力 佛罗里达州 过渡段 光束线 真空度
下载PDF
上一页 1 2 3 下一页 到第
使用帮助 返回顶部