Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various ...Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various types of hazardous elements are required. Among such impurities, hexavalent chromium (Cr(VI)) is very likely to become a future challenge. Different industrial ways to treat phosphate rock are currently being practised, and we have here studied how chromium behaves when using the nitro-phosphate process. The reduction mechanism of Cr (VI) in nitric acid and phosphoric acid solutions was investigated by measuring redox potential and UV-VIS spectra. The results show that Cr (VI) is not stable in strong nitric acid solutions. Reduction of Cr (VI) species decreased with decreasing temperature, NO<sub>2</sub> concentration, ionic strength and absence of light. These findings support the proposed reduction reaction:The reduction rate was observed proportional to the nitric acid decomposition: .展开更多
A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determ...A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determined as the most favorable composite for hexavalent chromium(Cr(VI))removal.Distinct influencing parameters were discussed,and 99.0%of Cr(VI)removal occurred within 360 min under these optimized parameters.Pseudo-second order kinetic model and intra-particle diffusion model well depicted Cr(VI)removal process.The XRD,FTIR,SEM,and XPS analyses verified the key roles of G-nZVI and functional groups,as well as the primary removal mechanisms involving electrostatic attraction,reduction,and complexation.G-nZVI@MKB2 exhibited good stability and reusability with only a 16.4%decline in Cr(VI)removal after five cycles.This study offered evidence that mango kernel could be recycled as a beneficial resource to synthesize green nZVI-loaded biochar composite for efficient Cr(VI)elimination from water.展开更多
Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,a...Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,and durability of the Cr-containing geopolymers were investigated.The experimental results indicate that the red mud-based geopolymer could effectively solidify/stabilize different types of Cr salts with solidification/stabilization rates of above 99.61%.Geopolymers are environmentally safe when the dosage of CaCr_(2)O_(7)is≤1.0wt%,or the dosage of CrCl_(3),Cr_(2)O_(3),and Na_(2)CrO_(4)is≤1.5wt%,respectively.The effects of Cr salts on the compressive strength varies with the type and content of Cr salts.The freeze-thaw cycle is more destructive to geopolymer properties than sulfate attack or acid rain erosion.The solidification/stabilization of Cr is mainly attributed to the following reasons:a)The chemical binding of Cr is related to the formation of Cr-containing hydrates(eg,magnesiochromite((Mg,Fe)(Cr,Al)_(2)O_(4)))and doping into N-A-S-H gel and C-A-S-H gel framework;b)The physical effect is related to the encapsulation by the hydration products(e g,N-A-S-H gel and C-A-S-H gel).This study provides a reference for the treatment of hazardous Cr-containing wastes by solid waste-based geopolymers.展开更多
A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling t...A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.展开更多
Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango ke...Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango kernel powder (MKP) as bioadsorbent material for removal of Cr (VI) from water. Uv-visible spectroscopy was used to monitor and quantify Cr (VI) during processing using the Beer-Lambert formula. Some parameters such as pH, mango powder, mass and contact time were optimized to determine adsorption capacity and chromium removal rate. Adsorption kinetics, equilibrium, isotherms and thermodynamic parameters such as ΔG˚, ΔH˚, and ΔS˚, as well as FTIR were studied to better understand the Cr (VI) removal process by MKP. The adsorption capacity reached 94.87 mg/g, for an optimal contact time of 30 min at 298 K. The obtained results are in accordance with a pseudo-second order Freundlich adsorption isotherm model. Finally FTIR was used to monitor the evolution of absorption bands, while Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate surface properties and morphology of the adsorbent.展开更多
We investigated the effects of calcination temperature(950-1450℃),steel slag content,and the total chromium content of steel slag on the Cr^(6+)contents of clinker samples produced using steel slags with different ch...We investigated the effects of calcination temperature(950-1450℃),steel slag content,and the total chromium content of steel slag on the Cr^(6+)contents of clinker samples produced using steel slags with different chromium contents.Additionally,the reactions of chromium in clinker(produced using steel slag)during calcination were studied.It is found that Cr^(6+)conversion increases with increasing calcination temperature to 1250℃,reaching a maximum of 43%-79%,before decreasing to 18%-42%at 1450℃.Cr^(6+)is mainly formed by the oxidation of trivalent chromium(Cr^(3+))during the solid-phase reaction stage of clinker calcination.Furthermore,the Cr^(6+)content of a clinker sample is proportional to the chromium content of its raw meal precursor and is mainly in the form of water-insoluble calcium chromate(CaCrO_(4)).The chromium in clinker is mainly distributed in tricalcium aluminate and tetracalcium aluminoferrite,however,some is present in silicate minerals.We expect to inform the monitoring and control of the Cr^(6+)content of clinker(produced using steel slag)and resulting cement.展开更多
Alumina-magnesia dry materials are widely used in induction furnace linings, but they show different kinds of damage when melting different kinds of alloy steel. In this paper, the chemical composition, phase composit...Alumina-magnesia dry materials are widely used in induction furnace linings, but they show different kinds of damage when melting different kinds of alloy steel. In this paper, the chemical composition, phase composition, and microstructure of the post-use dry materials for the working liners melting different kinds of steel were evaluated. Furthermore, the corrosion mechanism of the steel on the furnace lining materials was comprehensively analyzed. The findings reveal a significant ability of the Mn element in the molten steel to diffuse and penetrate into the refractories. Mn oxidizes to form MnO at the steel-refractory interface, and then forms a liquid phase with Al_(2)O_(3). The Cr element is dissolved into corundum and spinel of the refractories, resulting in lattice defects and structural damage of the materials. TiO2reacts with Al_(2)O_(3) to form Al_(2)TiO_(5), which plays a crucial role in preventing crack formation and propagation. Part of Ti4+dissolves into magnesia-alumina(MA), densifying the materials. TiO2also slows down the reaction between the Cr element and refractory components, further improving the corrosion resistance of the materials.展开更多
A new magnetic nanocomposite chitosan/EDTA/CeZnO(MEC-CeZnO)is synthesized as an efficient and eco-friendly bio-compound for the removal of chromium Cr(VI)metal ions and phenol organic matters from aqueous solutions.Na...A new magnetic nanocomposite chitosan/EDTA/CeZnO(MEC-CeZnO)is synthesized as an efficient and eco-friendly bio-compound for the removal of chromium Cr(VI)metal ions and phenol organic matters from aqueous solutions.Nanocomposites are characterized using field emission scanning electron microscope,energy dispersive X-ray spectroscopy,transmission electron microscope,X-ray diffraction,X-ray photoelectron spectroscopy,Fourier transform infrared spectroscopy,diffuse reflection spectroscopy,and PL methods.The reduction rate of Cr(VI)ions and phenol degradation is evaluated under various experimental conditions,separately and simultaneously.The average pore diameter and specific surface of MEC-CeZnO nanocomposite are obtained 50 nm and 210 m^(2)·g^(-1)respectively,which suggest the successful synthesis of the nanocomposite because of the increased surface area and reduced pores in comparison to previous studies.Moreover,the best Cr(VI)and phenol reduction efficiencies are 98%and 92%at 180 min of retention time,both following the Langmuir-Hinshelwood first-order kinetics.The mechanisms of Cr(VI)and phenol removal from aqueous solutions involved Cr(VI)reduction,phenol oxidation,and adsorption.Examining the reusability of MEC-CeZnO showed that both degradation and recovery capacity is stable in 5 cycles.展开更多
Cr(III)ehydrolyzed polyacrylamide(HPAM)gels have been extensively studied as a promising strategy controlling waste water production for mature oilfields.However,the gelation time of the current technologies is not lo...Cr(III)ehydrolyzed polyacrylamide(HPAM)gels have been extensively studied as a promising strategy controlling waste water production for mature oilfields.However,the gelation time of the current technologies is not long enough for in-depth placement.In this study,we report a novel synthesis method to obtain chromium chloride/poly(methyl methacrylate)(PMMA)nanocapsules which can significantly delay the gelation of HPAM through encapsulating the chromium chloride crosslinker.The chromium chloride-loaded nanocapsules(CreNC)are prepared via a facile inverse miniemulsion evaporation method during which the hydrophobic PMMA polymers,pre-dispersed in an organic solvent,were carefully controlled to precipitate onto stable aqueous miniemulsion droplets.The stable aqueous nanodroplets(W)containing Cr(III)are dispersed in a mixture of organic solvent(O1)with PMMA and nonsolvent medium(O2)to prepare an inverse miniemulsion.With the evaporation of the O1,PMMA forms CreNCs around the aqueous droplets.The CreNCs are readily transferred into water from the organic nonsolvent phase.The CreNCs exhibit the tunable size(358-983 nm),Cr loading(7.1%-19.1%),and Cr entrapment efficiency(11.7%-80.2%),with tunable zeta potentials in different PVA solutions.The CreNCs can delay release of Cr(III)and prolong the gelation time of HPAM up to 27 days.展开更多
A chemical composite plating of Ni-B_(4)C was used to prepare the surface-modified zirconia toughened alumina(ZTA)ceramic particles.The ceramic preforms were prepared by the plated ZTA and sodium silicate solution bin...A chemical composite plating of Ni-B_(4)C was used to prepare the surface-modified zirconia toughened alumina(ZTA)ceramic particles.The ceramic preforms were prepared by the plated ZTA and sodium silicate solution binder,followed by casting infiltration to prepare the ZTA particles reinforced high chromium cast iron(HCCI)composites.The result reveals that a distinct interface layer forms at the ZTA/HCCI interface,which consists of phases of ZrB_(2),FeB,Fe_(2)B,and NaSiO_(4).The interfacial wettability between ZTA and HCCI is improved by the diffusion and reaction of Ni and B_(4)C.The wear test reveals that the Ni-B_(4)C plated ZTA particles can effectively improve the wear resistance of the ZTA/HCCI composite,and the wear rate of the composite is decreased to 11.6%of HCCI.展开更多
To prevent dense chromium oxide covers from cracking during firing,such as internal cracking,surface cracking and fracture,the firing process of dense chromium oxide products was simulated,and the performance paramete...To prevent dense chromium oxide covers from cracking during firing,such as internal cracking,surface cracking and fracture,the firing process of dense chromium oxide products was simulated,and the performance parameters at several specific temperatures before and after densification of chromium oxide green bodies were tested.The temperature difference and the stress difference of chromium oxide green bodies were calculated by Finite Element Software at heating and cooling rates of 10,20,30 and 40℃·h^(-1),respectively.The results show that large temperature difference and thermal stress difference are the main causes of internal cracking,surface cracking and fracture of the brick.Suitable heating rates reduce or avoid internal cracking of the brick.When the heating rate is 30℃·h^(-1) below 1450℃and 10℃·h^(-1) above 1450℃,the temperature difference and the thermal stress difference in the brick are below 4℃and 4 MPa,respectively,and there is no internal crack in the brick after firing.The initial cooling stage is the key stage that causes cracking or fracture of bricks.When the cooling rate is 20℃·h^(-1) above 1450℃,the thermal stress difference in the brick is less than 4 MPa,which can significantly reduce the surface cracks and fracture of the brick.展开更多
The objective of this research was to evaluate the influences that supplemental dietary chromium propionate (CrP;0 or 0.4 mg·kg<sup>-</sup><sup>1</sup> added to the total diet on a DM basi...The objective of this research was to evaluate the influences that supplemental dietary chromium propionate (CrP;0 or 0.4 mg·kg<sup>-</sup><sup>1</sup> added to the total diet on a DM basis) has on plasma indicators of energy status in newly weaned steers upon introduction to the feedlot. For this experiment single source, Angus steers (n = 28;BW = 289 ± 12.0 kg) from a ranch in Western South Dakota were weaned and immediately shipped 579 km to the Ruminant Nutrition Center (RNC) in Brookings, SD. Steers were allotted to one of four 7.6 m × 7.6 m pens (2 pens/diet;7 steers/pen) at 4 d post-arrival to the RNC and test diets were initiated. No anabolic implant was used in this study. Subsequent BW measurements were obtained at 1400 h, to accommodate a post-prandial timing for blood sampling. This was 4 h after initial access to feed, and immediately prior to the afternoon feed delivery. Weights and blood sampling occurred on d 5, 12, 19, and 33. Whole blood samples were collected from all steers via jugular venipuncture and separated as plasma. There were no diet x day interactions (P ≥ 0.51) for plasma glucose, insulin, or urea-N. Plasma glucose, insulin, and urea-n levels were similar between diets (P ≥ 0.35). Plasma glucose and urea-n levels were not different across days (P ≥ 0.59). Insulin levels differed as a result of days of adaptation and were greatest (P = 0.01) on d 12 regardless of diet. There tended (P = 0.12) to be a diet x day interaction for NEFA levels. Plasma NEFA levels tended to be lower (P = 0.13) for calves fed CrP on d 5, and were greater (P = 0.09) on d 12 in calves fed CrP. The shift in NEFA on d 12 coincided with the spike in insulin levels. Both events occurred at the time that NEg intake was approaching the acclimated plateau and neither event impacted glucose status. In non-ruminants, elevated insulin concentrations decrease circulating NEFA levels. We detected minimal differences in regard to plasma indicators of lipid metabolism in this study due to chromium supplementation. These data indicate that ruminants may differ from non-ruminants in the regulation and maintenance of glucose status and body fat catabolism during the post-absorptive state.展开更多
The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The ef...The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The effects of molar ratio of C to Fe n(C)/n(Fe) and temperature on the behaviors of vanadium and chromium during direct reduction and magnetic separation were investigated. The reduced samples were characterized by X-ray diffraction(XRD), scanning election microscopy(SEM) and energy dispersive spectrometry(EDS) techniques. Experimental results indicate that the recoveries of vanadium and chromium rapidly increase from 10.0% and 9.6% to 45.3% and 74.3%, respectively, as the n(C)/n(Fe) increases from 0.8 to 1.4. At n(C)/n(Fe) of 0.8, the recoveries of vanadium and chromium are always lower than 10.0% in the whole temperature range of 1100-1250 °C. However, at n(C)/n(Fe) of 1.2, the recoveries of vanadium and chromium considerably increase from 17.8% and 33.8% to 42.4% and 76.0%, respectively, as the temperature increases from 1100 °C to 1250 °C. At n(C)/n(Fe) lower than 0.8, most of the FeO·V2O3 and FeO·Cr2O3 are not reduced to carbides because of the lack of carbonaceous reductants, and the temperature has little effect on the reduction behaviors of FeO·V2O3 and FeO·Cr2O3, resulting in very low recoveries of vanadium and chromium during magnetic separation. However, at higher n(C)/n(Fe), the reduction rates of FeO·V2O3 and FeO·Cr2O3 increase significatly because of the excess amount of carbonaceous reductants. Moreover, higher temperatures largely induce the reduction of FeO·V2O3 and FeO·Cr2O3 to carbides. The newly formed carbides are then dissolved in the γ(FCC) phase, and recovered accompanied with the metallic iron during magnetic separation.展开更多
The electro-reduction of chromium oxide（Cr2O3） was investigated in an equimolar mixture of CaCl2-NaCl molten salt at 800℃ for developing a more efficient process for chromium preparation. Cyclic voltammetry and pot...The electro-reduction of chromium oxide（Cr2O3） was investigated in an equimolar mixture of CaCl2-NaCl molten salt at 800℃ for developing a more efficient process for chromium preparation. Cyclic voltammetry and potentiostatic electrolysis were used to study the electro-reduction of the Cr2O3-loaded metallic cavity electrode. In addition, a number of parameters affecting the rate and extent of Cr2O3 electrolysis were considered to better understand the electrolysis process. The results demonstrate that CaCl2-NaCl molten salt is applicable for preparing Cr directly from Cr2O3 and the electrolysis parameters exert great influence on the cathode product. Under optimal experimental conditions, nodular Cr with an oxygen content of 0.5%（mass fraction） was obtained without any chromium carbides detected by XRD. Furthermore, the relatively high solubility of CaO and quite rapid crystal growth result in the formation of large platelet CaCr2O4, and the addition of NaCl to CaCl2 results in several variations on the electrolysis process and the product morphology from pure CaCl2 molten salt.展开更多
Study was carried out to analyze the distribution and migration patterns,soil-to-plant transfer and potential health risks of chromium in soil-vegetable system in areas near a ferro-alloy manufactory in Hunan province...Study was carried out to analyze the distribution and migration patterns,soil-to-plant transfer and potential health risks of chromium in soil-vegetable system in areas near a ferro-alloy manufactory in Hunan province.The results show that soils near sewer outlet,sewer channel and in control area are averaged 2 239.5,995.33 and 104.9 mg/kg,respectively.The total Cr has a relative accumulation in soil depth of 200-400 mm near the sewer outlet,mainly enriches in the surface layer（0-200 mm） near the sewer channel and decreases gradually in unpolluted soils.The differential concentration level of enrichment between layers is little.The results also indicate that the three vegetables of celery,lettuce and Chinese cabbage are able to convert the potentially toxic Cr（Ⅵ） species into the non-toxic Cr（Ⅲ） species,and the chromium contents in the edible parts of the vegetables are averaged 11.95 mg/kg.The transfer factors of the three vegetables follow the order：Chinese cabbage lettuce celery.The estimated total daily intake of chromium substantially exceeds the dietary allowable value,which may pose health risks to local population.展开更多
[Objective] The aim was to develop a rapid, simple method for determination of chromium and zinc in soil samples by flame atomic absorption spectrometry.[Method] The method for determination of Cr and Zn in soil by co...[Objective] The aim was to develop a rapid, simple method for determination of chromium and zinc in soil samples by flame atomic absorption spectrometry.[Method] The method for determination of Cr and Zn in soil by combined flame atomic absorption spectrometry and microwave digestion was used. [Result] The concentration curve was linear within the range of 0-0.8 mg/L for Cr and 0-0.8 mg/L for Zn, the detection limits of Cr and Zn was 0.0025 mg/L and 0.002 3 mg/L, respectively. Recoveries of 102.4%-103.2% for Cr and 97.7%-98.3% for Zn were obtained for there soil samples. [Conclusion] The proposed method has the advantages of simple operation, high sensitivity, and high efficiency; it was successfully used for determination of Cr and Zn in soil samples.展开更多
[Objective] To optimize the techniques for culturing Cr-enriched Dendrobi-um candidum protocorm. [Method] By adopting Plackett-Burman test, the effects of time, temperature, Cr-content in medium, NAA content, KT conte...[Objective] To optimize the techniques for culturing Cr-enriched Dendrobi-um candidum protocorm. [Method] By adopting Plackett-Burman test, the effects of time, temperature, Cr-content in medium, NAA content, KT content and light intensi-ty on Cr-enriched protocorm were researched. Three factors of time, Cr-content in medium and light intensity had statistical y significant effects; then steepest ascent procedures were applied to define optimal response region of these three factors; fi-nal y the optimal factors were determined by RSM analysis. [Result] The results showed that the optimal conditions for Cr-enrichment were chromium concentration at 0.37 mg/L, culture time of 59 d and il umination intensity of 1 822.22 lx. The predicted value of Cr-content in protocorm was 5.08 mg/kg. [Conclusion] RSM can optimize the techniques for culturing Cr-enriched protocorm of Dendrobium can-didum, provide the optimum process parameters and lay the foundation for further research.展开更多
The extraction experiments of chromium（W） from aqueous waste solution by predispersed solvent extraction （PDSE） process with extractant （HEHPEHE） and its mixture, including acidic extractant （D2EHPA）, alkaline...The extraction experiments of chromium（W） from aqueous waste solution by predispersed solvent extraction （PDSE） process with extractant （HEHPEHE） and its mixture, including acidic extractant （D2EHPA）, alkaline extractant （TOA） and neutral extractant （TBP） were carried out respectively. It is found that the extractant HEHPEHE exhibited high extraction selectivity to chromium（III） from aqueous waste solution. The colloidal liquid aphrons （CLAs） were successfully generated using kerosene as a solvent, HEHPEHE as an extractant, sodium dodecyl benzene sulphate （SDBS） as a surfactant in aqueous phase and polyoxyethylene sorbitol anhydride monolaurate （Tween-20） in oil phase. To study the extraction efficiency and advantages of the PDSE process in the removal of chromium（III）, the effects of major factors, such as initial chromium（III） concentration, volume of colloidal gas aphrons （CGAs）, HEHPEHE volume fraction, phase ratio （solvent phase to water phase）, mass fraction of dodecyl trimethylammonium bromide （HTAB）, mass fraction of SDBS, mass fraction of Tween-20 and initial pH of aqueous waste solution were also investigated and the appropriate process conditions were obtained. Under the appropriate conditions, the extraction efficiency of chromium（III） above 99.9 % can be achieved and the treated aqueous waste solution can be discharged directly without polluting the environment.展开更多
The oxidation induration and reduction swelling behavior of chromium-bearing vanadium titanomagnetite pellets(CVTP)with Cr2O3 addition were studied,and the reduction swelling index(RSI)and compressive strength(CS)of t...The oxidation induration and reduction swelling behavior of chromium-bearing vanadium titanomagnetite pellets(CVTP)with Cr2O3 addition were studied,and the reduction swelling index(RSI)and compressive strength(CS)of the reduced CVTP with simulated coke oven gas(COG)injection were investigated.The results showed that the CS of the CVTP decreases and the porosity of the CVTP increases with increasing amount of Cr2O3 added.The Cr2O3 mainly exists in the form of(Cr,Fe)2O3 solid solution in the CVTP and as Fe-Cr in the reduced CVTP.The CS of the reduced CVTP increases and the RSI of the reduced CVTP decreases with increasing amount of Cr2O3 added.The limited aggregation and diffusion of metallic iron contribute to the formation of dense lamellar crystals,which leads to the slight decrease for reduction swelling behavior of reduced CVTP.This work provides a theoretical and technical basis for the utilization of CVTP and other Cr-bearing ores such as chromite with COG recycling technology.展开更多
文摘Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various types of hazardous elements are required. Among such impurities, hexavalent chromium (Cr(VI)) is very likely to become a future challenge. Different industrial ways to treat phosphate rock are currently being practised, and we have here studied how chromium behaves when using the nitro-phosphate process. The reduction mechanism of Cr (VI) in nitric acid and phosphoric acid solutions was investigated by measuring redox potential and UV-VIS spectra. The results show that Cr (VI) is not stable in strong nitric acid solutions. Reduction of Cr (VI) species decreased with decreasing temperature, NO<sub>2</sub> concentration, ionic strength and absence of light. These findings support the proposed reduction reaction:The reduction rate was observed proportional to the nitric acid decomposition: .
基金supported by the National Natural Science Foundation of China(51808253)the Science and Technology Planning Project of Jilin Province(20220508008RC)+1 种基金Science and Technology Project of Jilin Provincial Education Department(JJKH20220295KJ and JJKH20210272KJ)the Science and Technology Projects of the Ministry of Housing and Urban-Rural Development(2018-K6-003).
文摘A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determined as the most favorable composite for hexavalent chromium(Cr(VI))removal.Distinct influencing parameters were discussed,and 99.0%of Cr(VI)removal occurred within 360 min under these optimized parameters.Pseudo-second order kinetic model and intra-particle diffusion model well depicted Cr(VI)removal process.The XRD,FTIR,SEM,and XPS analyses verified the key roles of G-nZVI and functional groups,as well as the primary removal mechanisms involving electrostatic attraction,reduction,and complexation.G-nZVI@MKB2 exhibited good stability and reusability with only a 16.4%decline in Cr(VI)removal after five cycles.This study offered evidence that mango kernel could be recycled as a beneficial resource to synthesize green nZVI-loaded biochar composite for efficient Cr(VI)elimination from water.
基金Funded by the National Natural Science Foundation of China(Nos.52074245,52374416 and 52202029)the China Postdoctoral Science Foundation(No.2022M721058)。
文摘Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,and durability of the Cr-containing geopolymers were investigated.The experimental results indicate that the red mud-based geopolymer could effectively solidify/stabilize different types of Cr salts with solidification/stabilization rates of above 99.61%.Geopolymers are environmentally safe when the dosage of CaCr_(2)O_(7)is≤1.0wt%,or the dosage of CrCl_(3),Cr_(2)O_(3),and Na_(2)CrO_(4)is≤1.5wt%,respectively.The effects of Cr salts on the compressive strength varies with the type and content of Cr salts.The freeze-thaw cycle is more destructive to geopolymer properties than sulfate attack or acid rain erosion.The solidification/stabilization of Cr is mainly attributed to the following reasons:a)The chemical binding of Cr is related to the formation of Cr-containing hydrates(eg,magnesiochromite((Mg,Fe)(Cr,Al)_(2)O_(4)))and doping into N-A-S-H gel and C-A-S-H gel framework;b)The physical effect is related to the encapsulation by the hydration products(e g,N-A-S-H gel and C-A-S-H gel).This study provides a reference for the treatment of hazardous Cr-containing wastes by solid waste-based geopolymers.
文摘A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.
文摘Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango kernel powder (MKP) as bioadsorbent material for removal of Cr (VI) from water. Uv-visible spectroscopy was used to monitor and quantify Cr (VI) during processing using the Beer-Lambert formula. Some parameters such as pH, mango powder, mass and contact time were optimized to determine adsorption capacity and chromium removal rate. Adsorption kinetics, equilibrium, isotherms and thermodynamic parameters such as ΔG˚, ΔH˚, and ΔS˚, as well as FTIR were studied to better understand the Cr (VI) removal process by MKP. The adsorption capacity reached 94.87 mg/g, for an optimal contact time of 30 min at 298 K. The obtained results are in accordance with a pseudo-second order Freundlich adsorption isotherm model. Finally FTIR was used to monitor the evolution of absorption bands, while Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate surface properties and morphology of the adsorbent.
文摘We investigated the effects of calcination temperature(950-1450℃),steel slag content,and the total chromium content of steel slag on the Cr^(6+)contents of clinker samples produced using steel slags with different chromium contents.Additionally,the reactions of chromium in clinker(produced using steel slag)during calcination were studied.It is found that Cr^(6+)conversion increases with increasing calcination temperature to 1250℃,reaching a maximum of 43%-79%,before decreasing to 18%-42%at 1450℃.Cr^(6+)is mainly formed by the oxidation of trivalent chromium(Cr^(3+))during the solid-phase reaction stage of clinker calcination.Furthermore,the Cr^(6+)content of a clinker sample is proportional to the chromium content of its raw meal precursor and is mainly in the form of water-insoluble calcium chromate(CaCrO_(4)).The chromium in clinker is mainly distributed in tricalcium aluminate and tetracalcium aluminoferrite,however,some is present in silicate minerals.We expect to inform the monitoring and control of the Cr^(6+)content of clinker(produced using steel slag)and resulting cement.
基金the National Natural Science Foundation of China(52272022)Key Program of Natural Science Foundation of Hubei Province(2021CFA071).
文摘Alumina-magnesia dry materials are widely used in induction furnace linings, but they show different kinds of damage when melting different kinds of alloy steel. In this paper, the chemical composition, phase composition, and microstructure of the post-use dry materials for the working liners melting different kinds of steel were evaluated. Furthermore, the corrosion mechanism of the steel on the furnace lining materials was comprehensively analyzed. The findings reveal a significant ability of the Mn element in the molten steel to diffuse and penetrate into the refractories. Mn oxidizes to form MnO at the steel-refractory interface, and then forms a liquid phase with Al_(2)O_(3). The Cr element is dissolved into corundum and spinel of the refractories, resulting in lattice defects and structural damage of the materials. TiO2reacts with Al_(2)O_(3) to form Al_(2)TiO_(5), which plays a crucial role in preventing crack formation and propagation. Part of Ti4+dissolves into magnesia-alumina(MA), densifying the materials. TiO2also slows down the reaction between the Cr element and refractory components, further improving the corrosion resistance of the materials.
文摘A new magnetic nanocomposite chitosan/EDTA/CeZnO(MEC-CeZnO)is synthesized as an efficient and eco-friendly bio-compound for the removal of chromium Cr(VI)metal ions and phenol organic matters from aqueous solutions.Nanocomposites are characterized using field emission scanning electron microscope,energy dispersive X-ray spectroscopy,transmission electron microscope,X-ray diffraction,X-ray photoelectron spectroscopy,Fourier transform infrared spectroscopy,diffuse reflection spectroscopy,and PL methods.The reduction rate of Cr(VI)ions and phenol degradation is evaluated under various experimental conditions,separately and simultaneously.The average pore diameter and specific surface of MEC-CeZnO nanocomposite are obtained 50 nm and 210 m^(2)·g^(-1)respectively,which suggest the successful synthesis of the nanocomposite because of the increased surface area and reduced pores in comparison to previous studies.Moreover,the best Cr(VI)and phenol reduction efficiencies are 98%and 92%at 180 min of retention time,both following the Langmuir-Hinshelwood first-order kinetics.The mechanisms of Cr(VI)and phenol removal from aqueous solutions involved Cr(VI)reduction,phenol oxidation,and adsorption.Examining the reusability of MEC-CeZnO showed that both degradation and recovery capacity is stable in 5 cycles.
基金The authors were also supported by the National Natural Science Foundation of China(grant number 52104057 and 52204041)Natural Science Foundation of Shandong Province(grant number ZR2021QE106)China Postdoctoral Science Foundation(grant number 2021M693506)during the writing of this paper at China University of Petroleum(East China).
文摘Cr(III)ehydrolyzed polyacrylamide(HPAM)gels have been extensively studied as a promising strategy controlling waste water production for mature oilfields.However,the gelation time of the current technologies is not long enough for in-depth placement.In this study,we report a novel synthesis method to obtain chromium chloride/poly(methyl methacrylate)(PMMA)nanocapsules which can significantly delay the gelation of HPAM through encapsulating the chromium chloride crosslinker.The chromium chloride-loaded nanocapsules(CreNC)are prepared via a facile inverse miniemulsion evaporation method during which the hydrophobic PMMA polymers,pre-dispersed in an organic solvent,were carefully controlled to precipitate onto stable aqueous miniemulsion droplets.The stable aqueous nanodroplets(W)containing Cr(III)are dispersed in a mixture of organic solvent(O1)with PMMA and nonsolvent medium(O2)to prepare an inverse miniemulsion.With the evaporation of the O1,PMMA forms CreNCs around the aqueous droplets.The CreNCs are readily transferred into water from the organic nonsolvent phase.The CreNCs exhibit the tunable size(358-983 nm),Cr loading(7.1%-19.1%),and Cr entrapment efficiency(11.7%-80.2%),with tunable zeta potentials in different PVA solutions.The CreNCs can delay release of Cr(III)and prolong the gelation time of HPAM up to 27 days.
基金financially supported by the National Natural Science Foundation of China(52005217)the University Research Platform and Research Projects of Guangdong Education Department(2022ZDZX3003)+2 种基金Basic and Applied Basic Research Fund Project of Guangdong Province in China(2022A1515010091,2021A1515010523,and 2020A1515110020)Basic Scientific Research Projects of Central Universities(No.21620344)Jinan University Open Fund for Advanced Materials(JNIWRM2021004)。
文摘A chemical composite plating of Ni-B_(4)C was used to prepare the surface-modified zirconia toughened alumina(ZTA)ceramic particles.The ceramic preforms were prepared by the plated ZTA and sodium silicate solution binder,followed by casting infiltration to prepare the ZTA particles reinforced high chromium cast iron(HCCI)composites.The result reveals that a distinct interface layer forms at the ZTA/HCCI interface,which consists of phases of ZrB_(2),FeB,Fe_(2)B,and NaSiO_(4).The interfacial wettability between ZTA and HCCI is improved by the diffusion and reaction of Ni and B_(4)C.The wear test reveals that the Ni-B_(4)C plated ZTA particles can effectively improve the wear resistance of the ZTA/HCCI composite,and the wear rate of the composite is decreased to 11.6%of HCCI.
文摘To prevent dense chromium oxide covers from cracking during firing,such as internal cracking,surface cracking and fracture,the firing process of dense chromium oxide products was simulated,and the performance parameters at several specific temperatures before and after densification of chromium oxide green bodies were tested.The temperature difference and the stress difference of chromium oxide green bodies were calculated by Finite Element Software at heating and cooling rates of 10,20,30 and 40℃·h^(-1),respectively.The results show that large temperature difference and thermal stress difference are the main causes of internal cracking,surface cracking and fracture of the brick.Suitable heating rates reduce or avoid internal cracking of the brick.When the heating rate is 30℃·h^(-1) below 1450℃and 10℃·h^(-1) above 1450℃,the temperature difference and the thermal stress difference in the brick are below 4℃and 4 MPa,respectively,and there is no internal crack in the brick after firing.The initial cooling stage is the key stage that causes cracking or fracture of bricks.When the cooling rate is 20℃·h^(-1) above 1450℃,the thermal stress difference in the brick is less than 4 MPa,which can significantly reduce the surface cracks and fracture of the brick.
文摘The objective of this research was to evaluate the influences that supplemental dietary chromium propionate (CrP;0 or 0.4 mg·kg<sup>-</sup><sup>1</sup> added to the total diet on a DM basis) has on plasma indicators of energy status in newly weaned steers upon introduction to the feedlot. For this experiment single source, Angus steers (n = 28;BW = 289 ± 12.0 kg) from a ranch in Western South Dakota were weaned and immediately shipped 579 km to the Ruminant Nutrition Center (RNC) in Brookings, SD. Steers were allotted to one of four 7.6 m × 7.6 m pens (2 pens/diet;7 steers/pen) at 4 d post-arrival to the RNC and test diets were initiated. No anabolic implant was used in this study. Subsequent BW measurements were obtained at 1400 h, to accommodate a post-prandial timing for blood sampling. This was 4 h after initial access to feed, and immediately prior to the afternoon feed delivery. Weights and blood sampling occurred on d 5, 12, 19, and 33. Whole blood samples were collected from all steers via jugular venipuncture and separated as plasma. There were no diet x day interactions (P ≥ 0.51) for plasma glucose, insulin, or urea-N. Plasma glucose, insulin, and urea-n levels were similar between diets (P ≥ 0.35). Plasma glucose and urea-n levels were not different across days (P ≥ 0.59). Insulin levels differed as a result of days of adaptation and were greatest (P = 0.01) on d 12 regardless of diet. There tended (P = 0.12) to be a diet x day interaction for NEFA levels. Plasma NEFA levels tended to be lower (P = 0.13) for calves fed CrP on d 5, and were greater (P = 0.09) on d 12 in calves fed CrP. The shift in NEFA on d 12 coincided with the spike in insulin levels. Both events occurred at the time that NEg intake was approaching the acclimated plateau and neither event impacted glucose status. In non-ruminants, elevated insulin concentrations decrease circulating NEFA levels. We detected minimal differences in regard to plasma indicators of lipid metabolism in this study due to chromium supplementation. These data indicate that ruminants may differ from non-ruminants in the regulation and maintenance of glucose status and body fat catabolism during the post-absorptive state.
基金Projects(2013CB632601,2013CB632604)supported by the National Basic Research Program of ChinaProject(51125018)supported by the National Science Foundation for Distinguished Young Scholars of China+1 种基金Project(KGZD-EW-201-2)supported by the Key Research Program of the Chinese Academy of SciencesProjects(51374191,21106167,51104139)supported by the National Natural Science Foundation of China
文摘The reduction behaviors of FeO·V2O3 and FeO·Cr2O3 during coal-based direct reduction have a decisive impact on the efficient utilization of high-chromium vanadium-bearing titanomagnetite concentrates. The effects of molar ratio of C to Fe n(C)/n(Fe) and temperature on the behaviors of vanadium and chromium during direct reduction and magnetic separation were investigated. The reduced samples were characterized by X-ray diffraction(XRD), scanning election microscopy(SEM) and energy dispersive spectrometry(EDS) techniques. Experimental results indicate that the recoveries of vanadium and chromium rapidly increase from 10.0% and 9.6% to 45.3% and 74.3%, respectively, as the n(C)/n(Fe) increases from 0.8 to 1.4. At n(C)/n(Fe) of 0.8, the recoveries of vanadium and chromium are always lower than 10.0% in the whole temperature range of 1100-1250 °C. However, at n(C)/n(Fe) of 1.2, the recoveries of vanadium and chromium considerably increase from 17.8% and 33.8% to 42.4% and 76.0%, respectively, as the temperature increases from 1100 °C to 1250 °C. At n(C)/n(Fe) lower than 0.8, most of the FeO·V2O3 and FeO·Cr2O3 are not reduced to carbides because of the lack of carbonaceous reductants, and the temperature has little effect on the reduction behaviors of FeO·V2O3 and FeO·Cr2O3, resulting in very low recoveries of vanadium and chromium during magnetic separation. However, at higher n(C)/n(Fe), the reduction rates of FeO·V2O3 and FeO·Cr2O3 increase significatly because of the excess amount of carbonaceous reductants. Moreover, higher temperatures largely induce the reduction of FeO·V2O3 and FeO·Cr2O3 to carbides. The newly formed carbides are then dissolved in the γ(FCC) phase, and recovered accompanied with the metallic iron during magnetic separation.
基金Project(2013CB632600)supported by the National Basic Research Program of ChinaProjects(21376251,21406233)supported by the National Natural Science Foundation of ChinaProject supported by the Fund of Hubei Zhenhua Chemical Co.,Ltd.,China
文摘The electro-reduction of chromium oxide（Cr2O3） was investigated in an equimolar mixture of CaCl2-NaCl molten salt at 800℃ for developing a more efficient process for chromium preparation. Cyclic voltammetry and potentiostatic electrolysis were used to study the electro-reduction of the Cr2O3-loaded metallic cavity electrode. In addition, a number of parameters affecting the rate and extent of Cr2O3 electrolysis were considered to better understand the electrolysis process. The results demonstrate that CaCl2-NaCl molten salt is applicable for preparing Cr directly from Cr2O3 and the electrolysis parameters exert great influence on the cathode product. Under optimal experimental conditions, nodular Cr with an oxygen content of 0.5%（mass fraction） was obtained without any chromium carbides detected by XRD. Furthermore, the relatively high solubility of CaO and quite rapid crystal growth result in the formation of large platelet CaCr2O4, and the addition of NaCl to CaCl2 results in several variations on the electrolysis process and the product morphology from pure CaCl2 molten salt.
基金Project (2009ZX07212-001-01) supported by the Key Project of National Natural Science Foundation for Water Pollution Control and RemediationProject (50925417) supported by the National Funds for Distinguished Young Scientists+1 种基金Project (50830301) supported by the National Natural Science Foundation of ChinaProject (51074191) supported by the National Natural Science Foundation of China
文摘Study was carried out to analyze the distribution and migration patterns,soil-to-plant transfer and potential health risks of chromium in soil-vegetable system in areas near a ferro-alloy manufactory in Hunan province.The results show that soils near sewer outlet,sewer channel and in control area are averaged 2 239.5,995.33 and 104.9 mg/kg,respectively.The total Cr has a relative accumulation in soil depth of 200-400 mm near the sewer outlet,mainly enriches in the surface layer（0-200 mm） near the sewer channel and decreases gradually in unpolluted soils.The differential concentration level of enrichment between layers is little.The results also indicate that the three vegetables of celery,lettuce and Chinese cabbage are able to convert the potentially toxic Cr（Ⅵ） species into the non-toxic Cr（Ⅲ） species,and the chromium contents in the edible parts of the vegetables are averaged 11.95 mg/kg.The transfer factors of the three vegetables follow the order：Chinese cabbage lettuce celery.The estimated total daily intake of chromium substantially exceeds the dietary allowable value,which may pose health risks to local population.
基金Supported by Key Fund of Guangxi Academy of Agricultural Sciences(2014JZ01 and2013YZ07)~~
文摘[Objective] The aim was to develop a rapid, simple method for determination of chromium and zinc in soil samples by flame atomic absorption spectrometry.[Method] The method for determination of Cr and Zn in soil by combined flame atomic absorption spectrometry and microwave digestion was used. [Result] The concentration curve was linear within the range of 0-0.8 mg/L for Cr and 0-0.8 mg/L for Zn, the detection limits of Cr and Zn was 0.0025 mg/L and 0.002 3 mg/L, respectively. Recoveries of 102.4%-103.2% for Cr and 97.7%-98.3% for Zn were obtained for there soil samples. [Conclusion] The proposed method has the advantages of simple operation, high sensitivity, and high efficiency; it was successfully used for determination of Cr and Zn in soil samples.
文摘[Objective] To optimize the techniques for culturing Cr-enriched Dendrobi-um candidum protocorm. [Method] By adopting Plackett-Burman test, the effects of time, temperature, Cr-content in medium, NAA content, KT content and light intensi-ty on Cr-enriched protocorm were researched. Three factors of time, Cr-content in medium and light intensity had statistical y significant effects; then steepest ascent procedures were applied to define optimal response region of these three factors; fi-nal y the optimal factors were determined by RSM analysis. [Result] The results showed that the optimal conditions for Cr-enrichment were chromium concentration at 0.37 mg/L, culture time of 59 d and il umination intensity of 1 822.22 lx. The predicted value of Cr-content in protocorm was 5.08 mg/kg. [Conclusion] RSM can optimize the techniques for culturing Cr-enriched protocorm of Dendrobium can-didum, provide the optimum process parameters and lay the foundation for further research.
基金Project (NCET-07-0577) supported by New Century Excellent Talents of Ministry of Education, China
文摘The extraction experiments of chromium（W） from aqueous waste solution by predispersed solvent extraction （PDSE） process with extractant （HEHPEHE） and its mixture, including acidic extractant （D2EHPA）, alkaline extractant （TOA） and neutral extractant （TBP） were carried out respectively. It is found that the extractant HEHPEHE exhibited high extraction selectivity to chromium（III） from aqueous waste solution. The colloidal liquid aphrons （CLAs） were successfully generated using kerosene as a solvent, HEHPEHE as an extractant, sodium dodecyl benzene sulphate （SDBS） as a surfactant in aqueous phase and polyoxyethylene sorbitol anhydride monolaurate （Tween-20） in oil phase. To study the extraction efficiency and advantages of the PDSE process in the removal of chromium（III）, the effects of major factors, such as initial chromium（III） concentration, volume of colloidal gas aphrons （CGAs）, HEHPEHE volume fraction, phase ratio （solvent phase to water phase）, mass fraction of dodecyl trimethylammonium bromide （HTAB）, mass fraction of SDBS, mass fraction of Tween-20 and initial pH of aqueous waste solution were also investigated and the appropriate process conditions were obtained. Under the appropriate conditions, the extraction efficiency of chromium（III） above 99.9 % can be achieved and the treated aqueous waste solution can be discharged directly without polluting the environment.
基金financially supported by the National Natural Science Foundation of China (Nos.51674084, 51174051, and 51574082)
文摘The oxidation induration and reduction swelling behavior of chromium-bearing vanadium titanomagnetite pellets(CVTP)with Cr2O3 addition were studied,and the reduction swelling index(RSI)and compressive strength(CS)of the reduced CVTP with simulated coke oven gas(COG)injection were investigated.The results showed that the CS of the CVTP decreases and the porosity of the CVTP increases with increasing amount of Cr2O3 added.The Cr2O3 mainly exists in the form of(Cr,Fe)2O3 solid solution in the CVTP and as Fe-Cr in the reduced CVTP.The CS of the reduced CVTP increases and the RSI of the reduced CVTP decreases with increasing amount of Cr2O3 added.The limited aggregation and diffusion of metallic iron contribute to the formation of dense lamellar crystals,which leads to the slight decrease for reduction swelling behavior of reduced CVTP.This work provides a theoretical and technical basis for the utilization of CVTP and other Cr-bearing ores such as chromite with COG recycling technology.
